催化裂化干气与苯烷基化催化蒸馏制乙苯反应网络热力学研究

 高温气相反应条件下的催化裂化干气制乙苯过程中，容易生成甲苯和二甲苯等副产物；在该过程中采用催化蒸馏技术，使苯与乙烯在低温条件下进行反应，可大幅度降低产品中二甲苯的含量．通过对催化裂化干气与苯烷基化催化精馏过程中的各反应步骤进行分析与热力学计算，结合反应的实际产物组成，提出了苯与乙烯烷基化的反应网络，探讨了苯与乙烯烷基化反应过程中甲苯和二甲苯的形成机理及影响因素．结果表明，增大苯／乙烯比对提高乙烯平衡转化率及乙苯收率有利；在较低温度下进行烷基化反应，可大大减缓C－C键裂解速度，抑制甲苯和二甲苯生成，提高乙苯产品质量．     

色谱交点在多相催化研究中的应用I. 芳烃在分子筛催化剂上的交点

测定了苯、甲苯、乙苯、二乙苯在四种分子筛催化剂上的保留体积。这些催化剂都被用于研究从苯和乙醇合成乙苯的反应中。发现了苯、甲苯、乙苯的logVg-1/T直线都有共同交点。证明了气相色谱中同系物交点的一般原则, 可以用在催化反应的研究中,从而为该反应提供一些有用的信息。     

色谱交点在多相催化研究中的应用I. 芳烃在分子筛催化剂上的交点

测定了苯、甲苯、乙苯、二乙苯在四种分子筛催化剂上的保留体积。这些催化剂都被用于研究从苯和乙醇合成乙苯的反应中。发现了苯、甲苯、乙苯的logVg-1/T直线都有共同交点。证明了气相色谱中同系物交点的一般原则, 可以用在催化反应的研究中,从而为该反应提供一些有用的信息。     

色谱交点在多相催化研究中的应用——Ⅰ.芳烃在分子筛催化剂上的交点

测定了苯、甲苯、乙苯、二乙苯在四种分子筛催化剂上的保留体积.这些催化剂都被用于研究从苯和乙醇合成乙苯的反应中.发现了苯、甲苯、乙苯的 logV_g-1/T 直线都有共同交点.证明了气相色谱中同系物交点的一般原则,可以用在催化反应的研究中,从而为该反应提供一些有用的信息.     

ZSM—5分子筛吸附分离对二乙苯的研究

本文用动态法对二乙苯在ＺＳＭ－５分子筛上的吸附进行了研究，考察了温度，脉冲进料量，解吸剂的流速，解吸剂的性质等分离效果的影响，确定了最佳操作条件：温度为２００℃￣２３０℃，常压，以甲苯为解吸剂，解吸剂流量２５０￣３５０Ｋｇ／ｍ＾２·ｈ。对二乙苯的单程收率为６０，纯度〉９５％。     

ZSM-5分子筛吸附分离对二乙苯的研究

本文用动态法就对二乙苯在ＺＳＭ－５分子筛上的吸附进行了研究，考察了温度、脉冲进料量、解吸剂的流速、解吸剂的性质等对分离效果的影响，确定了最佳操作条件：温度为２００℃～２３０℃，常压，以甲苯为解吸剂，解吸剂流量 ２５０～３５０Ｋｇ／ｍ２·ｈ，对二乙苯的单程收率为 ６０％，纯度＞９５％。     

多束毛细管柱–离子迁移率谱检测环境大气中的苯系物

采用多束毛细管柱–离子迁移率谱(MCC–IMS)系统对环境大气中的苯、甲苯、乙苯、二甲苯和苯乙烯5种苯系物进行快速检测。IMS漂移管温度为80℃,载气和漂移气均为洁净空气,测得苯系物的约化迁移率。苯、甲苯、乙苯、二甲苯和苯乙烯分别在0.20~3.00,0.20~2.00,0.15~1.00,0.25~3.00,0.08~1.00 mg/m~3质量浓度范围内线性良好,线性相关系数均不小于0.96。基于3倍噪声计算,苯、甲苯、乙苯、二甲苯和苯乙烯的检出限分别为0.055,0.023,0.017,0.065和0.013 mg/m~3。MCC–IMS法可快速检测混合样品中5种苯系物,其中苯、甲苯和苯乙烯的定量相对误差分别为5.0%,9.4%,0.2%,测定结果的相对标准偏差分别为2.7%,5.0%,6.7%(n=6)。MCC–IMS的单次测量可在3 min内完成。     

碱金属改性Y分子筛的甲苯氧化甲基化反应性能及基酸碱性质

碱金属改性Ｙ分子筛的甲苯氧化甲基化反应性能及其酸碱性质＊周灵萍李伟苏明李赫口亘陶克毅＊＊（南开大学化学系，天津３０００７１）关键词Ｙ型分子筛，甲苯，甲烷，氧化甲基化，苯乙烯，乙苯，酸性，碱性分类号Ｏ６４３／ＴＱ４２苯乙烯和乙苯是重要的化工原料．以往合...     

有机膨润土对水中苯、甲苯、乙苯、二甲苯和铬酸根离子的吸附性能

污水处理;有机膨润土对水中苯、甲苯、乙苯、二甲苯和铬酸根离子的吸附性能     

吹扫捕集-气相色谱分析海水和沉积物中的苯、甲苯、乙苯及二甲苯

单环芳烃苯、甲苯、乙苯和二甲苯（简称BTEX）是石油的重要组分，也是环境中需要重点监测的致癌污染物。本实验建立了动态顶空（吹扫捕集）和光离子化检测器的气相色谱测量海水、沉积物中痕量BTEX的方法。在120—1200ng／L的浓度范围，苯、甲苯、乙苯、间对二甲苯及邻二甲苯标准溶液的检出限分别为6．4、35．2、15．8、12．3、10．7ng／L，相对标准偏差0．9％-6．1％。样品无需预处理，海水中BTEX回收率为93．50％-98．40％。7个渤海表层海水样品中BTEX的浓度均低于140ng／L；海底沉积物中苯、甲苯、乙苯、间对二甲苯及邻二甲苯浓度分别为169—1243、531—1732、1308—5624、237—1136、510—5194ng／L。测量方法和结果对评价环境污染具有重要意义。     

水体中痕量挥发性有机物单体碳同位素组成分析

将固相微萃取(SPME)技术与冷阱富集系统相结合,对水体中痕量挥发性有机物进行了单体碳同位素分析,方法检测限较常规SPME提高了一个数量级。在优化的条件下,对20 μg/L的三氯乙烯/四氯乙烯和10 μg/L的苯/甲苯水溶液进行了单体碳同位素分析,相比于纯溶剂(液相)碳同位素值,顶空(气相)同位素分析误差不超过0.5‰,而样本标准偏差为0.3‰。对某受四氯乙烯污染的北京地下水进行了同位素测定,近污染源点(B408)与远污染源点(B230)四氯乙烯的碳同位素值(δ13C)分别为 -37.8‰和-34.45‰     

基于平行因子分析法解析遥感傅里叶变换红外光谱谱图

本研究利用平行因子分析法(PARAFAC)完成了甲苯、苯和甲醇三组分体系的遥感傅里叶变换红外光谱(FTIR)谱图的同时定性定量分析.在有丙酮干扰情况下,定量分析的误差分别在6.61、18.76、16.00以下.将PARAFAC的输出结果作为偏最小二乘法(PLSDA)模型输入,实现了定性分析的自动完成.对主动式下数据定性分析的识别率和拒绝率均为100%,对被动式下数据的拒绝率为90%,识别率为85%.分析结果表明,PARAFAC可以同时进行定性定量分析,避免了干扰物存在的影响,可以满足遥感FTIR对多组分体系的实时、在线监测的需要.     

毛细管气相色谱法测定腈纶布料中苯、甲苯和二甲基甲酰胺残留

 建立了同时定量测定腈纶布料及其服装中的苯、甲苯和二甲基甲酰胺残留的毛细管气相色谱分析方法。测得的回收率分别为 93 .3 % ,1 0 1 .8% ,94.9% ;变异系数为 3 .4% ,2 .0 % ,2 .8%。方法简便、快速、准确。     

苯酚、马尿酸和甲基马尿酸的反相高效液相色谱分析

本文提出了人体内苯、甲苯和二甲苯的代谢产物苯酚、马尿酸和甲基马尿酸的反相高效液相色谱分析法,讨论了其保留机制和样品预处理技术.以ODS为固定相,甲醇-水-醋酸为流动相时可实现良好分离.方法回收率为97.3%,相对标准偏差为1.02%.提出的方法可用于尿样分析,适用于临床与职业病防治的监测分析.     

Vapor-phase testing of the memory-effects in benzene- and toluene-imprinted polymers conditioned at elevated temperature

The preparation of polymers imprinted with common aromatic solvents such as benzene and toluene is an under-exploited subject of research. The present study was aimed at the understanding of whether true solvent memory effects can be achieved by molecular imprinting, as well as if they are stable at elevated temperature. A set of copolymers, comprising low and high cross-linking levels, was prepared from four different combinations of functional monomer and cross-linker, namely methacrylic acid (MAA)/ethylene glycol dimethacrylate (EGDMA), methyl methacrylate (MMA)/EGDMA, MAA/divinyl benzene (DVB) and MMA/DVB. Each possible combination was prepared separately in benzene, toluene and acetonitrile. The obtained materials were applied as coatings onto nickel–titanium (Ni–Ti) alloy wires which were incorporated into solid-phase microextraction devices and finally tested for their ability to competitively adsorb vapors from the headspace of an aqueous solution containing a few volatile organic compounds.     

流动气体捕集法测定贯叶连翘提取物中大孔树脂残留物

采用流动气体捕集法,通过GC／MS法测定贯叶连翘提取物中大孔树脂残留物—苯、甲苯和二乙烯苯。与萃取、回流和顶空进样三种处理方式比较,自制的流动气体捕集装置能够很好地收集待测成分并有效地消除干扰。整体(流动气体捕集法处理 含量测定)检出限和回收率(苯：0．3ng/g,99．0％;甲苯：0．8ng／g,99．5％;二乙烯苯：0．5ng／g,99．2％),与GC／MS法所得结果(苯：0．1ng／g,99．2％;甲苯：0．2ng／g,99．4％;二乙烯苯：0．1ng／g,99．2％)无显著差别,说明该法有较低的检出限和良好的回收率。经其他3种方式处理后,检出限变差回收率下降。结果证明流动气体捕集法适于中药提取物中大孔树脂残留物的定量检测。     

Recognition of benzene, toluene and xylene using TGS array integrated with linear and non-linear classifier

Three volatile organic compounds (VOCs): benzene, toluene and xylene were measured with an array of six Taguchi gas sensors in the air with variable humidity content. The recognition of single compounds was performed, based on measurement results. The principal component analysis (PCA) pointed at humidity as the main classification factor in the measurement data set. The linear discriminant analysis (LDA) was applied to overcome this drawback and enforce classification with respect to benzene, toluene or xylene. It was shown that discriminant function analysis (DFA), which is an LDA method allowed for 100% success rate in test samples recognition of benzene. It did not allow for accurate recognition of test samples of toluene or xylene. Following, the non-linear classifier, radial basis function neural network (RBFNN) was applied. A specific configuration of input ‘s was found, which provided for successful recognition of each single compound: benzene, toluene or xylene in air with variable humidity content.     

Quantitative evaluation of benzene, toluene, and xylene in the larvae of Drosophila melanogaster by solid-phase microextraction/gas chromatography/mass spectrometry for potential use in toxicological studies

A simple, rapid, and solvent-free method for quantitative determination of benzene, toluene, and Xylene in exposed Drosophila larvae was developed using headspace solid-phase microextraction (HS-SPME) coupled to GC/MS. Larvae fed on standard Drosophila food mixed with benzene, toluene, and Xylene for 48 h were homogenized in Milli-Q water. Extraction of benzene, toluene, and Xylene was performed at 65 degrees C for 30 min on the SPME fiber (silica-fused). Subsequently, the fiber was desorbed in the GC injection port, followed by GC/MS analysis in the selected-ion monitoring mode. An external calibration curve was used for the quantification of benzene, toluene, and Xylene in the exposed organism. Recoveries were in the range of 78-82% (intraday) and 76-81% (interday) in larvae, and 91-96% (intraday) and 87-92% (interday) in the diet. LOD with an S/N of 3:1 and LOQ with an S/N of 10:1 were in the range of 0.01-0.023 and 0.034-0.077 microg/L, respectively. Percent RSD values for benzene, toluene, and Xylene were in the range of 0.50-0.81 (intraday) and 0.89-1.23 (interday) for retention time, and 2.16--3.85 (intraday) and 2.99-4.95 (interday) for peak concentration, showing good repeatability. This method was sensitive enough to quantitate benzene, toluene, and Xylene in small exposed organisms like Drosophila larvae. The SPME/GC/MS method developed may have wider applications in various in vivo toxicological studies.     

采用二维气相色谱及毛细管色谱柱分析汽油中苯和甲苯的含量

采用微板流路控制技术(Deans Switch)和常见的商品毛细管柱HP-5 (30 m×0.32 mm×0.25 μm)和Rtx-TCEP (30 m×0.25 mm×0.4 μm),建立了一种全新的分析车用汽油中苯和甲苯含量的二维气相色谱方法。用该方法分析汽油中0～5%的苯和0～20%的甲苯,两者校正曲线的线性关系良好,相关系数分别为0.9994和0.9999;标准样品5次重复测定的相对标准偏差均小于1.5%;车用汽油实际样品中苯和甲苯的加标回收率在96.8%～103.8%之间。车用汽油实际样品测定结果和SH/T 0713-2002标准方法测定结果一致。该方法是车用汽油中苯和甲苯含量测定的一种简便快捷、准确可靠的分析方法。     

Formation of trimer and dimer radical cations of methyl-substituted benzenes in gamma-irradiated low-temperature matrices

Dimer and trimer radical cations of benzene, toluene, and xylenes were produced selectively after gamma-irradiation in low-temperature 2-methylpentane matrices with electron scavengers: oxygen (O(2)) and sec-butyl chloride (sec-BuCl). The charge resonance (CR) band of the trimer radical cation (M(3)(+)) produced via the corresponding dimer radical cation (M(2)(+)) is clearly seen in the solution containing O(2) as the temperature increases over a range from 80 to 90 K. In o-xylene solution, a fairly strong and distinct M(3)(+) CR absorption is observed; this is due to the large M(3)(+)/M(2)(+) relative extinction coefficient. All benzene derivatives show an equilibrium between dimer and trimer radical cations at approximately 90 K; however, the equilibrium constants of toluene and the xylenes are considerably lower than that of benzene. Formation of the trimer radical cation is inhibited in sec-BuCl, which has commonly been used as a low-temperature optical matrix for producing cationic species. An ab initio DFT method is applied to predict the geometry of M(3)(+), giving "slipped sandwich" (for benzene, m-xylene, and p-xylene) and "slipped fan-shaped" (toluene and o-xylene) structures as the most plausible geometries. The experimentally observed spectroscopic parameters reflect well those predicted by TD-DFT calculation based on geometry, suggesting strong dependence of the geometry of M(3)(+) on substitution patterns. This is the first report not only of direct spectroscopic observation of aromatic trimer radical cations in the condensed phase but also on the quantitative analysis of their equilibria.