新型荧光试剂1-(8-喹啉)-3-(3,5-二溴-2-吡啶)-三氮烯的合成及其应用

将具有荧光特性的杂环8-氨基喹啉和吡啶类试剂结合,并引入三氮烯结构,合成了新型荧光试剂1-(8-喹啉)-3-(3,5-二溴-2-吡啶)-三氮烯(QBPyT)。其结构经元素分析、红外光谱、核磁共振波谱证实。研究结果表明,在pH 9.5硼酸-氢氧化钠缓冲溶液的介质存在下,该试剂在λex/λem=248nm/496nm处产生强荧光,并且能与铅(Ⅱ)形成配合物从而使荧光增强。据此建立了三氮烯测定铅(Ⅱ)的新型荧光分析法。铅的浓度在5.0×10-7～1.2×10-5 mol.L范围内与其荧光强度呈线性关系,检出限(3S/N)为9.5×10-8 mol.L。将其应用于水样中铅(Ⅱ)的测定,测得回收率在92.6%～94.0%之间,测定值的相对标准偏差(n=5)小于3.5%。     

双波长荧光法同时测定水溶解态的茚、萘和菲

建立了一种同时测定水体中多组分溶解态多环芳烃的新方法。为消除共存组分干扰,利用三维荧光谱确定茚、萘和菲的最佳测量点为A(λex250.0nm,λem308.0nm)、B(λex225.0nm,λem335.0nm)、C(λex250.0nm,λem364.0nm);萘和菲相应的最佳参比波长分别为292.5nm和286.7nm,所建方法用于水体中茚、萘和菲的同时测定。其线性范围分别为:2.00×10-7～2.00×10-5mol/L、5.00×10-8～3.50×10-6mol/L和1.00×10-8～1.00×10-6mol/L;检出限分别为:8.63×10-9、1.01×10-8和5.29×10-10mol/L;相对标准偏差分别为:1.1%、1.0%和0.7%(n=7)。方法用于自来水样和海水样的测定,结果满意。     

新型杂环三氮烯荧光试剂1,8-双(2-苯并噻唑重氮氨基)萘的合成及其分析应用

将1,8-萘二胺和苯并噻唑类试剂结合, 并引入杂环三氮烯结构, 合成了新荧光试剂1,8-双(2-苯并噻唑重氮氨基)萘(BBTANP), 其结构经红外光谱、核磁共振谱和元素分析证实. 研究结果表明, 在碱性介质中, 该试剂与Cu(Ⅱ)形成1∶1的络合物, 并在λex/λem=362 nm/459 nm处产生荧光增强作用. 据此建立了BBTANP测定Cu(Ⅱ)的新型荧光分析法, 该方法的线性范围为8.0×10-7—1.0×10-5 mol /L, 检测限为1.3×10-7 mol/L. 将其应用于水样中Cu(Ⅱ)的测定, 结果令人满意.     

铝敏化荧光法测定甲磺酸加替沙星

研究了甲磺酸加替沙星的铝敏化荧光性质。实验发现,在pH6.00的邻苯二甲酸氢钾-NaOH缓冲体系中,溶液中的铝(Ⅲ)能与甲磺酸加替沙星反应生成稳定的络合物从而增强甲磺酸加替沙星的内源性荧光,使其荧光强度显著增强。据此建立了铝(Ⅲ)-甲磺酸加替沙星体系荧光增强法测定微量甲磺酸加替沙星的新方法。该体系在λex=365nm,λem=470nm时,甲磺酸加替沙星的浓度在1.28×10-8～3.15×10-6mol/L范围内与荧光强度呈良好的线性关系,方法检出限为8.6×10-9mol/L。相对标准偏差为1.3%(c=2.0×10-7mol/L,n=5)。此方法已成功用于药物制剂中甲磺酸加替沙星含量的测定。     

4-溴-1，8-萘酰亚胺衍生物室温磷光性质研究

本文研究了在环己烷存在下,β-环糊精诱导N-二氨乙基-4-溴-1,8-萘酰亚胺(DBN)的室温磷光(RTP),λex/λem=347/572 nm.详细考察了影响DBN室温磷光的各种因素,如β-环糊精、环己烷用量等.在pH 1.0～4.0范围内,RTP强度随pH值增大而减小.优化实验条件下,DBN的浓度在2.0×10-5～9.0×10-5mol/L范围内与RTP强度呈良好的线性关系,相关系数r=0.9984,栓出限为6.7×10-6mol/L.该方法已用于水样中DBN含量的测定,回收率为98.3%～102.6%,相对标准偏差小于1.4%.     

铽-依诺沙星-SDS敏化荧光猝灭法检测雷公藤红素

在pH 9.3的氨-氯化铵缓冲溶液中,铽(Ⅲ)能与依诺沙星、十二烷基硫酸钠(SDS)形成荧光配合物(λex=330 nm、λem=545 nm),SDS的存在能增强配合物的荧光强度。研究发现,在该反应体系中加入适量雷公藤红素溶液后,铽(Ⅲ)与依诺沙星络合物的激发、发射峰位置不变,但其荧光强度呈规律性下降。据此,建立了简单、快速、灵敏地测定雷公藤红素的荧光分析方法。雷公藤红素的浓度在5.2×10-6～8.4×10-5 mol/L范围内呈良好线性关系,方法的检出限为4.1×10-8 mol/L。     

β-环糊精增敏荧光法测定克拉霉素含量的研究

克拉霉素在λex=275、λem=325处能产生荧光,经β-环糊精增敏后,荧光强度大大增强,据此建立了测定克拉霉素含量的新方法。克拉霉素的浓度在5.0×10-7～5.0×10-6 mol/L范围内与体系荧光强度呈良好的线性关系,相关系数R=0.9992,检出限为3.9×10-7 mol/L。对药物制剂中克拉霉素的含量进行测定,测定值与标示值吻合,回收率在97%以上。该方法可用于测定胶囊和血清样品中克拉霉素的含量。     

荧光光度法测定环境水样中的苯酚和对苯二酚

建立了荧光光度法直接测定环境水样中的苯酚和对苯二酚的新方法.通过β-环糊精增敏,三维荧光扫描选择测量波长,在波长对为λex/λem=273/307 nm时测定苯酚,苯酚的线性范围为0～1×10-4 mol/L,检出限为6.6×10-8 mol/L;在波长对为λex/λem=295/331 nm时测定对苯二酚, 对苯二酚的线性范围为0～1.5×10-5 mol/L,检出限为5.2×10-9 mol/L,回收率达到93.5%～103.5%.     

铁敏化荧光分析法测定乳酸环丙沙星的研究

研究了胶束体系中乳酸环丙沙星的铁敏化荧光性质.实验发现,在pH 5.56的HAc-NaAc介质中,溶液中的Fe(Ⅲ)能与乳酸环丙沙星和十二烷基硫酸钠(SDS)反应生成稳定的络合物从而增强乳酸环丙沙星分子的内源性荧光,使其荧光强度显著增强.据此,建立了Fe(Ⅲ)-乳酸环丙沙星-SDS三元体系荧光增强法测定微量乳酸环丙沙星的新方法.该体系在最大激发波长λex=365nm,最大发射波长λem=430 nm时,乳酸环丙沙星浓度在4.0×10-9～2.0×10-5 mol/L范围内与其荧光强度呈良好的线性关系.方法的检出限为:6.2×10-10 mol/L,相对标准偏差(RSD)为1.8%(c=2.0×10-7 mol/L,n=5).     

荧光试剂3-(4-氨基苯基)中氮茚-1-羧酸甲酯用于亚硝酸根测定

介绍了一种新的测定亚硝酸根的荧光探针分子———3-(4-氨基苯基)中氮茚-1-羧酸甲酯(API)。API在酸性介质中与亚硝酸根生成重氮盐化合物,进一步在碱性介质中生成相应的羟基二氮烯,使荧光强度明显增强。基于该反应,提出了一种操作简便、灵敏度高、选择性好的亚硝酸根荧光测定方法。该方法对亚硝酸根检测的线性范围为4.5×10-8~7.5×10-6mol/L,检出限为8.3×10-9mol/L(0.38μg/L,S/N=3)。用于检测水体中亚硝酸根浓度,取得了满意的结果。     

Spectrofluorimetric quantification of bromazepam using a highly selective optical probe based on Eu–bromazepam complex in pharmaceutical and serum samples

A rapid, simple and sensitive spectrofluorimetric method for determination of trace amount of bromazepam is developed. In phosphate buffer of pH 7.4. The bromazepam enhance the luminescence intensity of the Eu³⁺ ion in Eu³⁺–bromazepam complex at λ_ex = 390 nm. The produced luminescence intensity of Eu³⁺–bromazepam complex is in proportion to the concentration of bromazepam. The working range for the determination of bromazepam is 2.3 × 10⁻⁸ to 6.2 × 10⁻⁷ M with detection limit (LoD) and quantitative detection limit (LoQ) of 3 × 10⁻⁹ and 1.2 × 10⁻⁸ M, respectively. While, the working range, detection limit (LoD) and quantitative detection limit (LoQ) in case of the quantum yield calculations are 3.7 × 10⁻⁸ to 3.4 × 10⁻⁷ M with of 3.4 × 10⁻⁹ and 9.2 × 10⁻⁸ M, respectively. The enhancement mechanism of the luminescence intensity in the Eu³⁺–bromazepam system has been also explained.     

Comparison of the effects of visible femtosecond laser pulses and continuous wave laser radiation of low average intensity on the clonogenicity of Escherichia coli

To evaluate the contribution of local pulsed heating of light-absorbing microregions to biochemical activity, irradiation of Escherichia coli was carried out using femtosecond laser pulses (λ = 620 nm, τ_p=3 × 10⁻¹³ s, f_p = 0.5 Hz, E_p = 1.1 × 10⁻³J cm⁻², I_av = 5.5 × 10⁻⁴ W cm⁻², I_p = 10⁹ W cm⁻²) and continuous wave (CW) laser radiation (λ = 632.8 nm, I = 1.3 W cm⁻²). The irradiation dose required to produce a similar biological effect (a 160%–190% increase in the clonogenic activity of the irradiated cells compared with the non-irradiated controls) is a factor of about 10³ lower for pulsed radiation than for CW radiation (3.3 × 10⁻¹ and 7.8 × 10² J cm⁻² respectively). The minimum size of the microregions transiently heated on irradiation with femtosecond laser pulses is estimated to be about 10 Å, which corresponds to the size of the chromophores of hypothetical primary photoacceptors—respiratory chain components.     

Spectrofluorometric study of 1,4-diaminoanthraquinone-calcium complex in aqueous sulfuric acid mediums: Spectrofluorometric determination of calcium

The spectrofluorometric study was made of the complex 1,4-diaminoanthraquinone-Ca in aqueous sulfuric mediums [λ_max,ex = 410 nm; λ_max,em = 580 nm; 50% H₂O; stable for at least 4 hr; range temperature OPTIMUM = 20–35 °C; [R]_optimum = 2 × 10⁻⁴M; stoichiometry 2:1 (fluorescent complex) and 1:1 (no fluorescent complex)]. A new method for the spectrofluorometric determination of Ca traces is proposed for concentrations between 150 and 400 ppb. The relative error and the interferences of the method have been investigated.     

Investigation of the spectral properties of a squarylium near-infrared dye and its complexation with Fe(III) and Co(II) ions

The spectral features of the squarylium near-infrared (NIR) dye NN525 in different solutions and its complexation with several metal ions were investigated. The absorbance maximum of the dye is λ=663 nm in methanol. This value matches the output of a commercially available laser diode (650 nm), thus making use of such a source practical for excitation. The emission wavelength of the dye in methanol is λ_em=670 nm. The addition of either Fe(III) ion or Co(II) ion resulted in fluorescence quenching of the dye. The Stern–Volmer quenching constant, K_SV, was calculated from the Stern–Volmer plot to be K_SV=2.70×10⁷ M⁻¹ for Co(II) ion. The K_SV value for Fe(III) ion could not be established due to the non-linearity of the Stern–Volmer plot and the modified Stern–Volmer plot for this ion. The detection limit is 6.24×10⁻⁸ M for Fe(III) ion and 1.55×10⁻⁵ M for Co(III) ion. The molar ratio of the metal to the dye was established to be 1:1 for both metal ions. The stability constant, K_S, of the metal–dye complex was calculated to be 3.14×10⁶ M⁻¹ for the Fe–dye complex and 2.64×10⁵ M⁻¹ for the Co–dye complex.     

Binding of 6-propyl-2-thiouracil to human serum albumin destabilized by chemical denaturants

We compared the binding affinity of 6-propyl-2-thiouracil (PTU) with native and destabilized human serum albumin (HSA) as a model to assess the binding ability of albumin in patients suffering from chronic liver or renal diseases. Urea (U) and guanidine hydrochloride (Gu·HCl) at a concentration of 3.0 M were used as denaturation agents.Increasing the concentration of PTU from 0.8 × 10⁻⁵ to 1.20 × 10⁻⁴ M in the systems with HSA causes a decrease in fluorescence intensity of the protein excited with both 280 and 295 nm wavelengths. The results indicate that urea and Gu·HCl bind to the carbonyl group and then to the NH-group. To determine binding constants we used the Scatchard plots. The presence of two classes of HSA–PTU binding sites was observed. The binding constants (K_b) are equal to 1.99 × 10⁴ M⁻¹ and 1.50 × 10⁴ M⁻¹ at λ_ex = 280 nm, 5.20 × 10⁴ M⁻¹ and 1.65 × 10⁴ M⁻¹ at λ_ex = 295 nm. At λ_ex = 280 nm the number of drug molecules per protein molecule is a_I = 1.45 and a_II = 1.32 for I and II binding sites, respectively. At λ_ex = 295 nm they are a_I = 0.63 and a_II = 1.54 for the I and II binding sites.The estimation of the binding ability of changed albumin in the uremic and diabetic patients suffering from chronic liver or renal diseases is very important for safety and effective therapy.     

Determination of trace amounts of mercury(II) in water samples using a novel kinetic catalytic ligand substitution reaction of hexacyanoruthenate(II)

A simple, sensitive, selective and rapid kinetic catalytic method has been developed for the determination of Hg(II) ions at micro-level. This method is based on the catalytic effect of Hg(II) ion on the rate of substitution of cyanide in hexacyanoruthenate(II) with nitroso-R-salt (NRS) in aqueous medium and provides good accuracy and precision. The concentration of Hg(II) catalyst varied from 4.0 to 10.0 × 10⁻⁶ M and the progress of reaction was followed spectrophotometrically at 525 nm (λ_max of purple-red complex [Ru(CN)₅NRS]³⁻,  = 3.1 × 10³ M⁻¹ s⁻¹) under the optimized reaction conditions; 8.75 × 10⁻⁵ M [Ru(CN)₆⁴⁻], 3.50 × 10⁻⁴ M [nitroso-R-salt], pH 7.00 ± 0.02, ionic strength, I = 0.1 M (KCl), temp 45.0 ± 0.1 °C. The linear calibration curves, i.e. calibration equations between the absorbance at fixed times (t = 15, 20 and 25 min) versus concentration of Hg(II) ions were established under the optimized experimental conditions. The detection limit was found to be 1.0 × 10⁻⁷ M of Hg(II). The effect of various foreign ions on the proposed method has also been studied and discussed. The method has been applied to the determination of mercury(II) in aqueous solutions.     

Spectrophotometric study of pseudopurpurin-Pd(II) dimer complex. Spectrophotometric determination of traces of Pd(II)

We have studied spectrophotometrically the Pseudopurpurin-Pd(II) complex in an ethanolic-water medium ¦Ethanolamine ¦_optimum = 4 × 10⁻¹M; λ = 670 nm; 20% H₂O; stable for at least 4 hr; ¦Reagent¦_optimum = 5 × 10⁻⁵M; stoichiometry 2:2; log K = 17.7. A new method for the spectrophotometric determination of Pd traces is proposed for concentrations between 0.30 and 2.40 ppm. The relative error and the interferences of the method have been investigated.     

A novel fluorescent distinguished probe for Cr (VI) in aqueous solution

Salicylaldehyde rhodamine B hydrazone (SRBH) was developed as a new spectrofluorimetric probe for the selective and sensitive detection of CrO₄²⁻ in acidic conditions. The proposed method was based on the special oxidation reaction between non-fluorescent SRBH by potassium dichromate to produce a highly fluorescent rhodamine B, as a product. Under the optimum conditions described, the fluorescence enhancement at 591 nm was good linearly related to the concentration of CrO₄²⁻ from 1.0 × 10⁻⁸ to 3.0 × 10⁻⁷ M (0.42–12.6 ng mL⁻¹) with a correlation coefficient of R² = 0.9989 (n = 10) and a detection limit of 1.5 × 10⁻⁹ M (0.063 ng mL⁻¹). The relative standard deviation (R.S.D.) was 2.0% (n = 6). The proposed method was also successfully applied to the determination of chromium (VI) in drinking water, river water and synthetic samples.     

Kinetic spectrophotometric method for the determination of urinary cobalt based on its catalytic effect on the oxidation of -adrenaline hydrochloride by hydrogen peroxide

A catalytic for determination of nanomolar concentrations of Co(II), i.e., oxidation of -adrenaline hydrochloride with H₂O² in alkaline medium, is proposed. The reaction gives a low limit of detection of 2.5 × 10 ⁻⁹ M Co(II) in the reaction mixture, good reproducibility with a relative standard deviation (R.S.D.) of 4−5% in the Co(II) concentration range 8.0 × 10⁻⁹−8.0 × 10⁻⁸M and good selectivity. On the basis of this indicator reaction, a catalytic-spectrophotometric method for the determination of cobalt in small urine samples (5.00 ml) was elaborated. The analysis of 17 urine samples, taken from healthy persons of different ages, gave cobalt concentrations in the range 0.20–1.50 μmol 1⁻¹. The R.S.D. for ten replicate analyses of a urine sample with an average cobalt content of 0.63 μmol 1⁻¹ was 5.6%. The reliability of the method was verified by a comparative photometric method (r = 0.9755) and by a determination based on known additions of cobalt (r = 0.9894).     

A novel method for determination of peroxynitrite based on hemoglobin catalyzed reaction

A novel spectrofluorimetric method for the determination of peroxynitrite is proposed. The method is based on a mimetic enzyme catalyzed reaction with hemoglobin as the catalyst and l-tyrosine as the substrate. A new fluorescent substance is produced that might probably be the coupled dimmer of tyrosine, which, instead of nitryl-tyrosine, is likely to be a new marking substance of ONOO⁻ injury in vivo. Kinetics of the reaction is studied and the possible reaction mechanism is also recommended. The proposed method is simple and highly sensitive with a detection limit of 5.00 × 10⁻⁸ mol L⁻¹ of peroxynitrite. A liner calibration graph is obtained over the peroxynitrite concentration range 5.60 × 10⁻⁷ to 2.10 × 10⁻⁵ mol L⁻¹, with a correlation coefficient of 0.9983. Interferences from some amino acids and metal ions normally seen in biological samples, and also some anions structurally similar to ONOO⁻ are studied.