Pt nanoparticles modified Au nanowire array for amperometric and potentiometric detection of glucose

A new glucose biosensor, based on the modification of highly ordered Au nanowire arrays (ANs) with Pt nanoparticles (PtNPs) and subsequent surface adsorption of glucose oxidase (GOx), is described. Morphologies of ANs and ANs/PtNPs were observed by scanning electron microscope. The electrochemical properties of ANs, ANs/GOx, ANs/PtNPs, and ANs/PtNPs/GOx electrodes were compared by cyclic voltammetry. Results obtained from comparison of the cyclic voltammograms show that PtNPs modification enhances electrochemical catalytic activity of ANs to H₂O₂. Hence, ANs/PtNPs/GOx biosensor exhibits much better sensing to glucose than ANs/GOx. Optimum deposition time of ANs/PtNPs/GOx biosensor for both amperometric and potentiometric detection of glucose was achieved to be 150 s at deposition current of 1?×?10^?6 A. A sensitivity of 0.365 μA/mM with a linear range from 0.1 to 7 mM was achieved for amperometric detection; while for potentiometric detection the sensitivity is 33.4 mV/decade with a linear range from 0.1 to 7 mM.     

Glucose biosensor based on graphite electrodes modified with glucose oxidase and colloidal gold nanoparticles

The electrochemistry of glucose oxidase (GOx) immobilized on a graphite rod electrode modified by gold nanoparticles (Au-NPs) was studied. Two types of amperometric glucose sensors based on GOx immobilized and Au-NPs modified working electrode (Au-NPs/GOx/graphite and GOx/Au-NPs/graphite) were designed and tested in the presence and the absence of N-methylphenazonium methyl sulphate in different buffers. Results were compared to those obtained with similar electrodes not containing Au-NPs (GOx/graphite). This study shows that the application of Au-NPs increases the rate of mediated electron transfer. Major analytical characteristics of the amperometric biosensor based on GOx and 13 nm diameter Au-NPs were determined. The analytical signal was linearly related to glucose concentration in the range from 0.1 to 10 mmol L^?1. The detection limit for glucose was found within 0.1 mmol L^?1 and 0.08 mmol L^?1 and the relative standard deviation in the range of 0.1–100 mol L^?1 was 0.04–0.39%. The τ_1/2 of V _max characterizes the storage stability of sensors: this parameter for the developed GOx/graphite electrode was 49.3 days and for GOx/Au-NPs/graphite electrode was 19.5 days. The sensor might be suitable for determination of glucose in beverages and/or in food.     

Glucose Biosensor Based on Silicon Nitride Nanoparticles

For the first time silicon nitride (Si₃N₄) nanoparticles was used for preparation electrochemical biosensor. GOx immobilized on the Si₃N₄ nanoparticles exhibits facile and direct electrochemistry. The surface coverage and heterogeneous electron transfer rate constant (k_s) of immobilized GOx were 6.3×10^?13 mol cm^?2 and 47.4±0.3 s^?1. The sensitivity, linear concentration range and detection limit of the biosensor for glucose detection were 38.57 µA mM^?1 cm^?2, 25 µM to 8 mM and 6.5 µM, respectively. This biosensor also exhibits good stability, reproducibility and long life time. These indicate Si₃N₄ nanoparticles is good candidate material for construction of third generation biosensor and bioelectronics devices.     

Pt-polyaniline nanocomposite on boron-doped diamond electrode for amperometic biosensor with low detection limit

Boron-doped diamond electrodes covered with a nanostructured Pt nanoparticle-polyaniline composite have been fabricated and employed as sensitive amperometric sensors with low detection limit. A highly conductive boron-doped diamond thin film (BDD) was prepared by chemical vapor deposition, and its morphology was characterized by scanning electron microscopy and transmission electron microscopy. The nanostructured composite layer was grown on the BDD electrode by electrochemical deposition of polyaniline and Pt nanoparticles. Glucose oxidase (GOx) was then adsorptively immobilized on the modified BDD electrode. The biosensor displays a large surface area, high catalytic activity of the Pt nanoparticles, efficient electron mediation through the conducting polymer, and low background current of the electrode. The biosensor exhibits an excellent response to glucose, with a broad linear range from 5.9 μM to 0.51 mM, a sensitivity of 5.5 μA·mM^?1, a correlation coefficient (R) of 0.9947, and a detection limit of 0.10 μM. The apparent Michaelis-Menten constant (K _M ^app ) and the maximum current density of the electrode are 4.1 mM and 0.021 mA, respectively. This suggests that the immobilized GOx possesses a higher affinity for glucose at the lower K _M ^app , and that the enzymatic reaction rate constitutes the rate-limiting step of the response.     

Ionic liquid/graphene oxide as a nanocomposite for improving the direct electrochemistry and electrocatalytic activity of glucose oxidase

By combination of 1-ethyl-3-methyl immidazolium ethyl sulfate as a typical room temperature ionic liquid (IL) and graphene oxide (GO) nanosheets, a nanocomposite was introduced for improving the direct electrochemistry and electrocatalytic activity of glucose oxidase (GOx). The enzyme on the IL–GO-modified glassy carbon electrode exhibited a quasireversible cyclic voltammogram corresponding to the flavine adenine dinucleotide/FADH₂ redox prosthetic group of GOx. At the scan rate of 100 mV?s^?1, the enzyme showed a peak-to-peak potential separation of 82 mV and the formal potential of ?463 mV (vs Ag/AgCl in 0.1 M phosphate buffer solution, pH?7.0). The kinetic parameters of the charge transfer rate constant, the electron transfer coefficient, and the apparent Michaelis–Menten constant were calculated as 1.36 s^?1 and 0.35 and 2.47 μM, respectively. When the modified electrode was examined as a biosensor for glucose determination, a linear range of 2.5–45 nM with detection limit of 0.175 nM (signal to noise?=?3) was obtained. The biosensor was stable for 2 months.     

Sonication-polished anodic TiO<Subscript>2</Subscript> nanotube array-based photoanode for efficient solar energy conversion

In this work, the capping layer atop anodic TiO₂ nanotube arrays (NTAs), which hinders filling of other guest materials and transport of charge carriers, is discerned to be TiO₂ nanotapes. Then, it is completely removed by a novel sonication-polishing (SP) treatment, after which Sb₂S₃ is subsequently introduced to fill the nanotubes by chemical bath deposition. The morphological, structural, and optical properties of the SP-treated TiO₂ NTAs and TiO₂ NTAs/Sb₂S₃ heterogeneous structures are characterized systematically. The results indicate that SP treatment opens the tops of nanotubes with diameters of ～120 nm, which endure a phase conversion from amorphous to anatase after calcination at 450 °C; besides, stibnite Sb₂S₃ with a band gap of ～1.75 eV inside the TiO₂ networks is formed upon heat treatment at 330 °C in Ar, which enhances the absorption in visible light range. The photoelectrochemical (PEC) and photovoltaic properties for the SP-treated TiO₂ NTAs are investigated. Results shows that the photoresponse of TiO₂ NTAs is improved by the SP treatment, and the photocurrent for the TiO₂ NTAs/Sb₂S₃ electrode is substantially enhanced as compared to the bare TiO₂ one. A high efficiency of 6.28 % is achieved in a TiO₂ NTAs/Sb₂S₃ PEC cell. In addition, charge recombination in the photoanode of dye-sensitized solar cells (DSSCs) is observed to be greatly retarded by using the SP-treated TiO₂ NTAs as compared to TiO₂ nanoparticles (NPs). Thus, the SP anodic TiO₂ NTAs are promising in applications in various PEC areas such as photocatalysis and sensitized solar cells.     

Construction of a biointerface for glucose oxidase through diazonium chemistry and electrostatic self-assembly technique

In this study, a new procedure for the fabrication of biosensors was developed. The method is based on the covalent attachment of nitrophenyl groups to the electrode surface via diazonium salt reaction followed by their conversion to amine moieties through electrochemical reduction and electrostatic layer-by-layer (LbL) assembly technique. In this procedure, highly stable iron oxide (Fe₃O₄) nanoparticles (IONPs), chitosan (CHIt), GOx, and Nile blue (NB) were assembled on the surface of aminophenyl modified glassy carbon electrode (AP/GCE) by LbL assembly technique. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to characterize the interfaces. The surface coverage of the active GOx and Michaelis–Menten constant (K _M) of the immobilized GOx were Γ?=?3.38?×?10^?11 mol cm^?2 and 2.54 mM, respectively. The developed biosensor displayed a well-defined amperometric response for glucose determination with high sensitivity (8.07 μA mM^?1) and low limit of detection (LOD) of 19.0 μM. The proposed approach allows simple biointerface regeneration by increasing pH which causes disruption of the ionic interactions and release of the electrostatic attached layers. The biosensor can then be reconstructed again using fresh enzyme. Simple preparation, good chemical and mechanical stabilities, and easy surface renewal are remarkable advantages of the proposed biosensor fabrication procedure.     

Glucose biosensor based on glucose oxidase immobilized on unhybridized titanium dioxide nanotube arrays

A glucose biosensor has been fabricated by immobilizing glucose oxidase (GOx) on unhybridized titanium dioxide nanotube arrays using an optimized cross-linking technique. The TiO₂ nanotube arrays were synthesized directly on a titanium substrate by anodic oxidation. The structure and morphology of electrode material were characterized by X-ray diffraction and scanning electron microscopy. The electrochemical performances of the glucose biosensor were conducted by cyclic voltammetry and chronoamperometry measurements. It gives a linear response to glucose in the 0.05 to 0.65 mM concentration range, with a correlation coefficient of 0.9981, a sensitivity of 199.6 μA mM^?1 cm^?2, and a detection limit as low as 3.8 µM. This glucose biosensor exhibited high selectivity for glucose determination in the presence of ascorbic acid, sucrose and other common interfering substances. This glucose biosensor also performed good reproducibility and long-time storage stability. This optimized cross-linking technique could open a new avenue for other enzyme biosensors fabrication.

Sol–gel immobilized enzymatic glucose biosensor on gold interdigitated array (IDA) microelectrode

An enzymatic glucose biosensor with good sensitivity, selectivity and stability employing interdigitated array microelectrode (IDA μ-electrode) was reported. IDA μ-electrode was prepared by photolithography method with its surface immobilized with a layer of glucose oxidase (GOx), entrapped in a three-dimensional network composed of chitosan and tetraethyl orthosilicate sol–gel. The surface of the as-prepared IDA μ-electrode was characterized by scanning electron microscope, electron spectroscopy for chemical analysis, and atomic force microscopy. The experimental parameters for the best glucose sensing performance were optimized according to the loading of GOx, the applied voltages, the concentration of mediator, and the pH for glucose detection. The resulted biosensor exhibited a good response to glucose with a wide linear range from 0 to 35 mM and a low detection limit of 1 mM. The glucose sensor also showed a short response time (within 5 s) that the fast response was reflected by the small Michaelis–Menten constant (K_M ^app) with a value of 2.94 mM. The reported glucose biosensor exhibited good sensitivity (8.74 μA/mM.cm²), reproducibility, and stability.     

Sensitization of Mn with CdS nanoparticles via electrochemical deposition technique for photocurrent enhancement of nanomaterial’s-sensitized photoelectrochemical cells

A photoconversion efficiency of 2.12% was obtained under visible light illumination by nanostructure-sensitized photoelectrochemical cells using Mn/CdS as sensitizer loaded on TiO₂ nanotube arrays (NTAs) (Mn/CdS/TiO₂). Sensitization of Mn on CdS nanoparticles pre-loaded on TiO₂ NTAs was carried out by a two-step electrodeposition method. Compared with unsensitized TiO₂ NTAs, the photocurrent had increased from 0.03 to 4.12 for Mn/CdS/TiO₂ prepared at 1 min. The effects of deposited Mn on the physical, chemical, and photoelectrochemical properties of the CdS/TiO₂ NTAs nanostructure were investigated by using UV–visible diffuse reflectance spectroscopy, X-ray diffractometry, and field-emission scanning electron microscopy coupled with energy dispersive X-ray spectroscopy. The photoelectrochemical analysis was examined in a three-electrode system under a halogen illumination by using the prepared film as the photo-anode.     

Direct electrochemistry and electrochemical biosensing of glucose oxidase based on CdSe@CdS quantum dots and MWNT-modified electrode

The direct electron transfer of glucose oxidase (GOx) was achieved based on the immobilization of CdSe@CdS quantum dots on glassy carbon electrode by multi-wall carbon nanotubes (MWNTs)-chitosan (Chit) film. The immobilized GOx displayed a pair of well-defined and reversible redox peaks with a formal potential (E ^θ’) of ?0.459 V (versus Ag/AgCl) in 0.1 M pH 7.0 phosphate buffer solution. The apparent heterogeneous electron transfer rate constants (k _s) of GOx confined in MWNTs-Chit/CdSe@CdS membrane were evaluated as 1.56 s^?1 according to Laviron's equation. The surface concentration (Γ*) of the electroactive GOx in the MWNTs-Chit film was estimated to be (6.52?±?0.01)?×?10^?11?mol?cm^?2. Meanwhile, the catalytic ability of GOx toward the oxidation of glucose was studied. Its apparent Michaelis–Menten constant for glucose was 0.46?±?0.01 mM, showing a good affinity. The linear range for glucose determination was from 1.6?×?10^?4 to 5.6?×?10^?3?M with a relatively high sensitivity of 31.13?±?0.02 μA?mM^?1?cm^?2 and a detection limit of 2.5?×?10^?5?M (S/N=3).     

Preparation and nonlinear optical properties of Au nanoparticles doped TiO2 thin films

Nano-sized noble metal nanoparticles doped dielectric composite films with large third-order nonlinear susceptibility due to the confinement and the enhancement of local field were considered to be applied for optical information processing devices, such as optical switch or all optical logical gates. In this paper, sol–gel titania thin films doped with gold nanoparticles (AuNPs, ~10 nm in average size) were prepared. AuNPs were firstly synthesized from HAuCl₄ in aqueous solution at ~60 °C, using trisodium citrate as the reducing agent, polyvinylpyrrolidone as the stable agent; then the particle size and optical absorption spectra of the AuNPs in aqueous solutions were characterized by transmitting electron microscopy and UV–Vis–NIR spectrometry. Sol–gel 2AuNPs–100TiO₂ (in %mol) thin films (5 layers, ~1 μm in thickness) were deposited on silica glass slides by multilayer dip-coating. After heat-treated at 300–1,000 °C in air, the AuNPs–TiO₂ thin films were investigated by X-ray diffraction, scanning electron microscopy and atomic force microscopy. The nonlinear optical properties of the AuNPs–TiO₂ thin films were measured with the Z-scan technique, using a femtosecond laser (200 fs) at the wavelength of 800 nm. The third-order nonlinear refractive index and nonlinear absorption coefficient of 2AuNPs–100TiO₂ films were at the order of 10^?12 cm²/W, and the order of 10^?6 cm/W, respectively, and the third-order optical nonlinear susceptibility χ⁽³⁾ was ~6.88 × 10^?10 esu.     

Direct Electrochemistry of Glucose Oxidase at Reduced Graphene Oxide and β‐Cyclodextrin Composite Modified Electrode and Application for Glucose Biosensing

A simple glucose biosensor has been developed based on direct electrochemistry of glucose oxidase (GOx) immobilized on the reduced graphene oxide (RGO) and β‐cyclodextrin (CD) composite. A well‐defined redox couple of GOx appears with a formal potential of ～?0.459 V at RGO/CD composite. A heterogeneous electron transfer rate constant (K_s) has been calculated for GOx at RGO/CD as 3.8 s^?1. The fabricated biosensor displays a wide response to glucose in the linear concentrations range from 50 µM to 3.0 mM. The sensitivity and limit of detection of the biosensor is estimated as 59.74 µA mM^?1 cm^?2 and 12 µM, respectively.     

Effect of Cl− anions on photocatalytic decomposition of gaseous ozone over Au @ Ag/TiO2 catalyst

Au core Ag shell composite structure nanoparticles were prepared using a sol method. The Au core Ag shell composite nanoparticles were loaded on TiO₂ nanoparticles as support using a modified powder–sol method, enabling the generation of Au @ Ag/TiO₂ photocatalysts for photocatalytic decomposition and elimination of ozone. The sols were characterized by means of ultraviolet–visible light (UV–Vis) reflection spectrometry, X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM). The activity of the Au @ Ag/TiO₂ photocatalysts for photocatalytic decomposition and elimination of ozone was evaluated and the effect of Cl^? anions on the photocatalytic activity of the catalysts was highlighted. Results showed that Au @ Ag/TiO₂ prepared via the modified powder–sol route in the presence of an appropriate amount of NaCl solid as demulsifier had better activity in the photocatalytic decomposition and elimination of ozone. At the same time, Au @ Ag/TiO₂ catalysts had better ability to resist poisonous Cl^? anions than conventional Au/TiO₂ catalyst. The reasons could be, first, that NaCl was capable of reducing the concentration of free Ag⁺ by adsorption on the surface of Ag particles forming AgCl and enhancing the formation of Au core Ag shell particles, leading to a better resistance to Cl^? anions of the catalysts, and, second, AgCl took part in the photocatalytic decomposition of ozone together with Au @ Ag/TiO₂ catalysts and had a synergistic effect on the latter, resulting in better photocatalytic activity of Au @ Ag/TiO₂ catalysts.     

Investigation of carbon-supported Ni@Ag core-shell nanoparticles as electrocatalyst for electrooxidation of sodium borohydride

Carbon-supported Ni@Ag core-shell nanoparticles were synthesized and used as the anode electrocatalyst for direct borohydride-hydrogen peroxide fuel cell (DBHFC). The morphology, structure, and composition of the as-prepared electrocatalysts are characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), and energy dispersive spectroscopy (EDS). Electrochemical characterizations are performed by cyclic voltammetry (CV), chronoamperometry (CA), linear scan voltammetry with rotating disk electrode (LSV RDE), and fuel cell test. The catalytic behaviors and main kinetic parameters (e.g., Tafel slope, number of electrons exchanged, exchange current density, and apparent activation energy) toward BH ₄ ^‐ oxidation on Ag/C and Ni@Ag/C electrocatalysts are determined. Results show that the as-prepared nanoparticles have a core-shell structure with the average size approximately 13 nm. The kinetics of NaBH₄ oxidation is faster for Ni@Ag/C than that for Ag/C. Among the as-prepared catalysts, the highest transition electron value and the lowest apparent activation energy are obtained on Ni₁@Ag₁/C; the values are 4.8 and 20.23 kJ mol^?1, respectively. The DBHFC using Ni₁@Ag₁/C as anode electrocatalyst and Pt mesh (1 cm²) as cathode electrode obtains the maximum anodic power density as high as 8.54 mW cm^?2 at a discharge current density of 8.42 mA cm^?2 at 25 °C.     

Amperometric Sensor Based on Neutral Red-Doped Silica Nanoparticles Coupled with Microdialysis for the Measurement of Glutamate in the Rat Striatum

Amperometric sensor based on neutral red-doped silica （NRSiO2） nanoparticles （NPs） was fabricated and coupled with a microdialysis sampling system




















































































































































































































































































for the detection of glutamate （Glu） in the rat striatum. The NRSiO2 NPs [about （45 ± 3） nm] were prepared with water-in-oil （W/O） microemulsion method, and characterized by transmission electron microscope （TEM） technique. The neutral red （NR） doped in silica network could maintain its high electroactivity and behave as an excellent electron mediator for electrocatalysis of hydrogen dioxide. Furthermore, the silica surface could prevent the leakage of NR, hence, the stability of biosensor was improved. The novel Glu biosensor showed a linear range from 5.0×10^-7 to 1.5×10^-4 mol/L, with a detection limit of 2.0×10^-7 mol/L （S/N=3）.     

Glucose biosensor based on new carbon nanotube-gold-titania nano-composites modified glassy carbon electrode

In this paper, a novel biosensor was prepared by immobilizing glucose oxidase （GOx） on carbon nanotube-gold-titania nanocomposites （CNT/Au/TiO2） modified glassy carbon electrode （GCE）. SEM was initially used to investigate the surface morphology of CNT/Au/TiO2 nanocomposites modified GCE, indicating the formation of the nano-porous structure which could readily facilitate the attachment of GOx on the electrode surface. Cyclic voltammogram （CV） and electrochemical impedance spectrum （EIS） were further utilized to explore relevant electrochemical activity on CNT]Au/TiO2 nanocomposites modified GCE. The observations demonstrated that the immobilized GOx could efficiently execute its bioelectrocatalytic activity for the oxidation of glucose. The biosensor exhibited a wider linearity range from 0.1 mmol L-1 to 8 mmol L^-1 glucose with a detection limit of 0.077 mmol L^- 1.     

Direct electrochemistry of hemoglobin and its biosensing for hydrogen peroxide on TiO2–polystyrene nanofilms

Nanofilms of titanium dioxide (TiO₂) nanoparticles that mediate the assembly of polystyrene (PS) nanoparticles for immobilizing hemoglobin (Hb) on carbon ionic liquid electrode have been developed. Fourier transform infrared spectroscopy shows that Hb retains its native structure in TiO₂–PS nanofilms. Scanning electron microscopy reveals that the nanofilms possess uniform morphology and Hb is immobilized on the surface of the nanofilms. Electrochemical investigation of the biosensor indicates that the direct electrochemistry of hemoglobin is realized on the nanofilms, and there is a formal potential of ?0.320 V in deaerated buffer solutions; the biosensor shows good electrocatalytic activity toward the reduction of hydrogen peroxide with a linear range from 0.5 to 640 μM, a detection limit of 0.2 μM (S/N = 3) and a sensitivity of 103 μA mM^?1. Thus, the nanofilms will have potential application in the design of novel electrochemical biosensors.     

Glucose biosensor based on a platinum electrode modified with rhodium nanoparticles and with glucose oxidase immobilized on gold nanoparticles

We have developed an enzymatic glucose biosensor that is based on a flat platinum electrode which was covered with electrophoretically deposited rhodium (Rh) nanoparticles and then sintered to form a large surface area. The biosensor was obtained by depositing glucose oxidase (GOx), Nafion, and gold nanoparticles (AuNPs) on the Rh electrode. The electrical potential and the fractions of Nafion and GOx were optimized. The resulting biosensor has a very high sensitivity (68.1 μA mM^?1 cm^?2) and good linearity in the range from 0.05 to 15 mM (r?=?0.989). The limit of detection is as low as 0.03 mM (at an SNR of 3). The glucose biosensor also is quite selective and is not interfered by electroactive substances including ascorbic acid, uric acid and acetaminophen. The lifespan is up to 90 days. It was applied to the determination of glucose in blood serum, and the results compare very well with those obtained with a clinical analyzer.

A Glucose Biosensor Based on Immobilization of Glucose Oxidase into 3D Macroporous TiO2

3D macroporous TiO₂ inverse opals have been derived from a sol‐gel procedure using polystyrene colloidal crystals as templates. EDS and SEM showed a face‐centered cubic (FCC) structure TiO₂ inverse opal was obtained. Glucose oxidase (GOx) was successfully immobilized on the surface of indium‐tin oxide (ITO) electrode modified by TiO₂ inverse opal (TiO_2(IO)). Electrochemical properties of GOx/TiO_2(IO)/ITO electrode were characterized by using the three electrodes system. The result of cyclic voltammetry showed that a couple of stable and well‐defined redox peaks for the direct electron transfer of GOx in absence of glucose, and the redox peak height enhanced in presence of 0.1 μM glucose. Compare with the ordinary structured GOx/TiO₂/ITO electrode, inverse opal structured GOx/TiO_2(IO)/ITO electrode has a better respond to the glucose concentration change. Under optimized experimental conditions of solution pH 6.8 and detection potential at 0.30 V versus saturated calomel electrode (SCE), amperometric measurements were performed. The sensitivity and the detection limit of glucose detection was 151 μA cm^?2 mM^?1 and 0.02 μM at a signal‐to‐noise ratio of 3, respectively. The good response was due to the good biocompatibility of TiO₂ and the large effective surface of the three‐dimensionally ordered macroporous structure.