Influence of SiC Electron Acceptor–Donor Modification on Thermal and Physical Properties of Carbon Fiber/SiC/Epoxy Composites

In this work, the effects of electron acceptor–donor modification on the surface properties of SiC were investigated in the mechanical interfacial properties of carbon fibers-reinforced SiC-impregnated epoxy matrix composites. The surface properties of the SiC were determined according to acid/base values and FT-IR, and contact angle measurements. The thermal and mechanical interfacial properties of the composites were evaluated using a thermogravimetric analysis, critical strain energy release rate mode II (G _IIC), and impact strength testing. As a result, the electron acceptor-treated SiC had a higher acid value and polar component in surface free energy than did the untreated SiC or the electron donor-treated SiC. The G _IIC and impact strength mechanical interfacial properties of the composites had been improved in the specimens treated by acidic solutions due to the good wetting and a high degree of adhesion with electron donor characteristic epoxy resins.     

Effects of plasma surface modification on the mechanical properties of carbon fiber and carbon fiber/epoxy composite

_The effect of surface treatment on mechanical properties of carbon fibers has been investigated by application of plasma polymerization of selected monomers in the vapor phase. The role of the fiber-matrix interface on carbon fiber-reinforced epoxy resin composites has also been studied. Composites have been prepared separately by the use of plasma-modified and unmodified carbon fibers in the epoxy resin matrix. The mechanical properties of carbon fibers (Hercules and Grafil) as well as of fiber/epoxy composites were examined by using single filament and three-point bending tests, respectively. It was observed that plasma polymerization treatment at selected plasma conditions led to significant improvement of interlaminar shear and flexural strength values of composites.     

Surface Modification of Ultrahigh-molecular-weight Polyethylene Fibers with Coupling Agent during Extraction Process

Ultrahigh molecular weight polyethylene (UHMWPE) fibers were treated with a coupling agent following the extraction of gel fibers, resulting in modified fibers after subsequent ultra-drawing. The structure and morphology of the modified UHMWPE fibers were characterized and their surface wetting, interfacial adhesion, and mechanical properties were investigated. It was found that the coupling agent was absorbed into the UHMWPE fiber and trapped on the fiber surface. Compared with unmodified UHMWPE fibers, the modified fibers had smaller contact angle, higher crystallinity, and smaller crystal size. The interfacial adhesion and mechanical properties of UHMWPE fibers were significantly improved with increasing coupling agent concentration and gradually reached a plateau value. After treatment with 1.5 wt% solution of a silane coupling agent (γ -aminopropyl triethoxysilane, SCA-KH-550), the interfacial shear strength of the UHMWPE-fiber/epoxy composites was increased by 108% and the tensile strength and modulus of modified UHMWPE fibers were increased by 11% and 37% respectively.     

Dielectric analysis of the interfacial polarization of alkali treated woven flax fibers reinforced epoxy composites

Dielectric measurements were performed on alkali treated flax fibers reinforced epoxy composites in the frequency range 0.1 Hz–1 MHz and the temperature range 40–170 °C. Two common dielectric relaxations were observed for all composites. The first one appearing at low temperatures was attributed to the water dipoles polarization due to the hydrophilic character of flax fibers. The second one observed at high temperatures was identified to the interfacial polarization. Analysis of this latter using the Havriliak–Negami model showed an improvement of the fibers/matrix adhesion by these alkali treatments. The best adhesion was obtained by the leaching treatment.     

Interfacial characterisation and mechanical properties of heat treated non-woven kenaf fibre and its reinforced composites

This paper reports on the comprehensive characterisation of heat treated kenaf fibre (KF) and its composites. The kenaf fibres were modified by heating for 2.5–12.5 h inside a drying oven. Heat treatment produces an increase in the crystallinity index and fibre strength of KF. The highest value of KF strength was recorded by applying heat treatment of 10 h on KF. The heat treatment results in the partial removal of impurities/extractives on the KF surface which is detected by scanning electron microscopy and X-ray photoelectron spectroscopy. Atomic force microscopy results signify the decrease of roughness, the increase in peak area density and the increase of the adhesion force on the surface area of heat treated KF. The effect of the heat treatment in enhancing the interface bonding characteristics between the KF and unsaturated polyester matrix can be reflected by the interlaminar shear strength (ILSS) and dynamic mechanical analysis value of the composites. The flexural properties of the composites showed a similar trend to ILSS. However, the fracture toughness revealed contrasting results. Water absorption induced a drastic loss of the mechanical properties of the composites albeit better retention of properties was observed in the case of heat-treated KF composites.     

Effect of fiber surface treatments on the fiber–matrix interaction in banana fiber reinforced polyester composites

Cellulosic fibers have been used as cost-cutting fillers in plastic industry. Among the various factors, the final performance of the composite materials depends to a large extent on the adhesion between the polymer matrix and the reinforcement and therefore on the quality of the interface. To achieve optimum performance of the end product, sufficient interaction between the matrix resin and the cellulosic material is desired. This is often achieved by surface modification of the resin or the filler. Banana fiber, the cellulosic fibers obtained from the pseudo-stem of banana plant (Musa sepientum) is a bast fiber with relatively good mechanical properties. The fiber surface was modified chemically to bring about improved interfacial interaction between the fiber and the polyester matrix. Various silanes and alkali were used to modify the fiber surface. Modified surfaces were characterized by SEM and FTIR. The polarity parameters of the chemically modified fibers were investigated using the solvatochromic technique. The results were further confirmed by electrokinetic measurements. Chemical modification was found to have a profound effect on the fiber–matrix interactions. The improved fiber–matrix interaction is evident from the enhanced tensile and flexural properties. The lower impact properties of the treated composites compared to the untreated composites further point to the improved fiber–matrix adhesion. In order to know more about the fiber–matrix adhesion, fractured surfaces of the failed composites where further investigated by SEM. Of the various chemical treatments, simple alkali treatment with NaOH of 1% concentration was found to be the most effective. The fiber–matrix interactions were found to be dependent on the polarity of the modified fiber surface.     

Roles of interfaces between carbon fibers and epoxy matrix on interlaminar fracture toughness of composites

The effect of atmospheric-pressure plasma treatment on high strength PAN-based carbon fibers had been studied in terms of fiber surface energetics and mode I and II interlaminar fracture toughness of unidirectional carbon fibers/epoxy matrix composites. The surface characterization of plasma treated carbon fibers was investigated by X-ray photoelectron spectroscopy (XPS) and contact angles. As a result, the plasma treatment changed the surface properties of the carbon fibers, mainly through formation of oxygen functional groups like hydroxyl, carbonyl, and carboxyl groups. According to contact angle measurements, it was observed that plasma treatment led to an increase in surface free energy of the fibers, mainly due to the increase of its specific component. Fracture toughness test results employing double-cantilever beam (DCB) and end notched flexure (ENF) specimens also showed that the increase in specific components or hydrogen bonding between the –OH groups on carbon fibers and the =O ring in epoxy matrix resins played an important role in improving the degree of adhesion at interfaces, resulting in an increase in the interfacial fracture toughness of the composites studied.     

Fiber-matrix adhesion mechanism of pitch-based carbon fiber composites

The fiber-matrix adhesion mechanism in high modulus pitch-based carbon fiber-epoxy matrix composites has been studied. The surface morphology and chemistry of the carbon fibers were examined by microscopic (SEM, STM), thermodynamic and spectroscopic (XPS, Raman) techniques. The interlaminar shear strength and transverse tensile strength of the composites made from surface-treated and untreated fibers were also obtained. In the microscopic analysis, there was no difference in the surface roughness between the surface-treated and untreated fibers. In the thermodynamic and spectroscopic analyses, surface treatment of the carbon fibers increased the amount of surface oxygen. The results indicated that the major role of the surface treatment on the carbon fiber-epoxy resin adhesion is not the mechanical interlocking effect by the surface roughness. The formation of surface oxygen-containing functional groups is assumed to account for the increase in fiber-matrix interfacial adhesion.     

Role of curing conditions and silanization of glass fibers on carbon nanotubes (CNTs) reinforced glass fiber epoxy composites

Curing behavior of amino-functionalized carbon nanotubes (ACNT) used as reinforcing agent in epoxy resin has been examined by thermal analysis. Experiments performed as per supplier’s curing conditions showed that modification of the curing schedule influences the thermo-mechanical properties of the nanocomposites. Specifically, the glass transition temperature (T_g) of ACNT-reinforced composites increased likely due to the immobility of polymer molecules, held strongly by amino carbon nanotubes. Further, a set of composites were prepared by implementing the experimentally determined optimal curing schedule to examine its effect on the mechanical properties of different GFRP compositions, while focusing primarily on reinforced ACNT and pristine nanotube (PCNT) matrix with silane-treated glass fibers. From the silane treatment of glass fibers in ACNT matrix composition it has been observed that amino silane is much better amongst all the mechanical (tensile and flexural) properties studied. This is because of strong interface between amino silane-treated glass fibers and modified epoxy resin containing uniformly dispersed amino-CNTs. On the other hand, PCNT GFRP composites with epoxy silanes demonstrated enhanced results for the mechanical properties under investigation which may be attributed to the presence of strong covalent bonding between epoxy silane of glass fiber and epoxy–amine matrix.     

Degradation Studies of Polycaprolactone in Banana Fibers Reinforced Thermoplastics Composites

In this paper we report the fabrication, properties and degradation studies of banana fibers–reinforced thermoplastic polymers. In order to impart hydrophobicity to the fibers and also to concomitantly increase interfacial bond strength, which is a critical factor for obtaining better mechanical properties of composites, banana fibers were treated with sodium hydroxide (5% and 10% for 4 h), sebacoyl chloride (SC) (0.5 g, 4 h), or toluene diisocyanate (TDl) (1.5 mL, 4 h). Mechanical properties of banana fibers treated with TDl were not affected to any significant extent, but there was an increase in tensile strength of fibers treated with sodium hydroxide (NaOH). Deterioration in mechanical properties was observed upon SC treatment. In thermograssimetre analogue (TGA) studies fibers showed initial mass loss (6.5%–9.5%) in the 50–150°C temperature region. Major weight loss occurred above 200°C. Scanning electron microscope (SEM) studies revealed an increase in surface roughness after alkali treatment. High density polyethylene (HDPE) modified by blending with poly (ε‐caprolactone) (80:20 w/w) was used as a thermoplastic matrix. Composites were fabricated by using 1 cm long banana fibers; the weight fraction of fibers was varied from 0.05–0.13. An increase in weight fraction of fibers resulted in an increase in tensile strength and modulus and decrease in elongation at break. Thin sheets and dumbbells were used for enzymatic and chemical hydrolysis degradation tests. The degradation of the material was monitored by weight change and loss of mechanical properties. The enzymatic degradation in (PCL) presence of Pseudomonas cepacia lipase (PCL) gave appreciable weight loss in PCL and blended materials.     

Effect of Alkali Treatment on Structure and Mechanical Properties of Acrylonitrile–Butadiene–Styrene/Bamboo Fiber Composites

The preparation and properties of wood–plastic composites (WPCs) based on acrylonitrile–butadiene–styrene (ABS) and bamboo fibers (BFs) are described. The BFs were first modified by alkali treatment in order to improve their adhesion to an ABS matrix. The BF modifications were monitored by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Styrene–maleic anhydride (SMA) copolymer, as a compatibilizer, was added to both the untreated and alkali-treated composites. The changes in the structure and the properties resulting from these treatments were observed by the SEM and mechanical tests. The experimental results indicated that both the alkali treatment of the BF and the inclusion of the SMA copolymer improved the interactions between the BF and ABS matrix, and promoted better mechanical properties of the composites.     

Roughness and fibre reinforcement effect onto wettability of composite surfaces

Wettability of glass/epoxy and carbon/epoxy composites materials has been determined via sessile drop technique. Good-Van Oss approach has been used to evaluate surface free energy parameters of smooth and rough surfaces. Results obtained point out the influence of fibre reinforcement on surface free energy of composite materials. In addition, the interest of surface treatment to increase surface roughness has been discussed in terms of wettability. To sum up, results obtained clearly demonstrate the necessity of considering properties of a given composite surface not only as a polymer but a fibre/polymer couple. The drawn conclusions are of great interest as it may have numerous consequences in applications such as adhesion.     

Enhancing the interfacial strength of glass/epoxy composites using ZnO nanowires

This paper investigated the application of ZnO nanowires (ZnO NW) to enhance the interfacial strength of glass/epoxy composites. ZnO NW were grown on glass fibers by hydrothermal method, tensile properties of bare and ZnO NW coated fibers were measured by single fiber tensile testing, wettability of fiber with resin was studied by contact angle measurements and finally the interfacial strength and mechanisms were determined by single fiber fragmentation testing of glass/epoxy composites. The surface coverage of ZnO NW on glass fibers was fairly uniform without formation of major clusters. The coating of ZnO NW slightly reduced the tensile strength and improved the tensile modulus of fibers. Wettability tests showed reduction in contact angles for ZnO NW coated fibers because of enhanced wetting and infiltration of epoxy resin into nanowires. In fragmentation testing of microcomposites, smaller and concentrated interfacial debonding zones for ZnO NW coated fibers indicated good stress transfer and strong interfacial adhesion. A new form of crossed and closely spaced stress patterns were observed for nanowires of high aspect ratios. The interfacial strength of ZnO NW coated fibers increased by at least 109% and by 430% on average, which was attributed to the increased surface area and mechanical interlocking provided by ZnO NW.     

Effect of chemical modifications of the pineapple leaf fiber surfaces on the interfacial and mechanical properties of laminated biocomposites

Natural fiber reinforced renewable resource based laminated composites were prepared from biodegradable poly(lactic acid) (PLA) and untreated or surface-treated pineapple leaf fibers (PALF) by compression molding using the film stacking method. The objective of this study was to determine the effects of surface treatment of PALF on the performance of the fiber-reinforced composites. X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) were used to aid in the analysis. The mechanical properties of the PLA laminated composites were improved significantly after chemical treatment. It was found that both silane- and alkali-treated fiber reinforced composites offered superior mechanical properties compared to untreated fiber reinforced composites. The effects of temperature on the viscoelastic properties of composites were studied by dynamic mechanical analysis (DMA). From the DMA results, incorporation of the PALF fibers resulted in a considerable increase of the storage modulus (stiffness) values. The heat defection temperature (HDT) of the PALF fiber reinforced PLA laminated composites was significantly higher than the HDT of the neat PLA resin. The differential scanning calorimeter (DSC) results suggest that surface treatment of PALF affects the crystallization properties of the PLA matrix. Additionally, scanning electron microscopy (SEM) was used to investigate the distribution of PLA within the fiber network. SEM photographs of fiber surface and fracture surfaces of composites clearly indicated the extent of fiber–matrix interface adhesion. It was found that the interfacial properties between the reinforcing PALF fibers and the surrounding matrix of the laminated composite are very important to the performance of the composite materials and PALF fibers are good candidates for the reinforcement fiber of high performance laminated biodegradable biocomposites.     

Surface Modification of Para-Aramid Fiber by Direct Fluorination and its Effect on the Interface of Aramid/Epoxy Composites

Surface modification of a para-aramid fiber (DAFIII) was performed by direct fluorination. The properties of treated and untreated fibers were characterized and compared in detail by mechanical testing, Fourier transform infrared (FTIR) spectroscopy characterization, X-ray photoelectron spectroscopy (XPS) analysis and static contact angle measurements. The results showed that little damage of the fiber occurred after direct fluorine treatment, and the content of polar groups on the fibers surfaces were increased significantly, which resulted in a lower value of contact angle. The interlaminar shear strength (ILSS) of DAFIII fiber/epoxy composites and the tensile strength of NOL-ring specimens increased by 33% and 12%, increasing to 56.2 MPa and 2340 MPa, respectively, which indicated that the interfacial adhesion between the matrix and the aramid fiber was improved significantly by the fluorination treatment. Further tests showed that the durability of the direct fluorination treatment on the aramid fiber was also satisfactory.     

Micromechanical Behavior of Carbon Nanotube-Covered SiC Fibers in Polymer Matrix Composites

The incorporation of nanotube-covered fibers in continuous fiber/epoxy composites has been shown to influence the mechanical, electrical, and thermal properties of the composite. Increased interlaminar shear stress, flexural strength and modulus have been reported in such composites over composites containing bare fibers. In this study, the microstructure and interfacial shear strength (ISS) of continuous silicon carbide fiber/epoxy composites with and without nanotubes grown from the SiC fiber surface were investigated with micro-Raman spectroscopy (MRS) and microscopy. The fibers with nanotubes grown from the surface were found to have a reduced ISS compared with the bare fibers. Electron microscopy showed good wetting of epoxy in the nanotube forests, but poor attachment of the nanotube forests to the fibers. These results suggest that the mechanism leading to improvements in bulk composite properties is not due to an improvement in the fiber/matrix ISS.     

The Controllable Surface Morphology of Polyimide (PI) Electrospun Fibers

Electrospun materials have been proposed for application for gas filtration, drug carriers, and tissue engineering. The surface morphology of electrospun fibers is the key for consideration for the above applications, such as pore size on the fiber surface, surface area, and roughness. In this work, we investigated the influence of polymer/solvent properties on soluble polyimide (PI) fibers. The studied PIs included three fluorinated aromatic polyimides containing naphthalene pendant groups. By using various solvents we adjusted the size, shape, and structure of the fibers. As a result, PI electrospun fibers could be achieved with width around 10 μm. The rough and smooth surface morphologies were studied by scanning electron microscopy (SEM). Surface wettability of the electrospun fiber membranes were characterized by contact angle measurement. The contact angles on the electrospun PI fiber mats for water and glycerol were in the range of 137.6°–144.5° and 139.1°–143.6°, respectively. Moreover, the rough fiber surface could make the electrospun fiber membrane possess good adhesive force for liquids. The results suggest that we could widen the application of electrospun membranes through controlling the fiber morphology.     

Short sisal fiber reinforced polypropylene composites: the role of interface modification on ultimate properties

Sisal fibers have been used for the reinforcement of polypropylene matrix. The compatibilization between the hydrophilic cellulose fiber and hydrophobic PP has been achieved through treatment of cellulose fibers with sodium hydroxide, isocyanates, maleic anhydride modified polypropylene (MAPP), benzyl chloride and by using permanganate. Various fiber treatments enhanced the tensile properties of the composites considerably, but to varying degrees. The SEM photomicrographs of fracture surfaces of the treated composites clearly indicated the extent of fiber–matrix interface adhesion, fiber pullout and fiber surface topography. Surface fibrillation is found to occur during alkali treatment which improves interfacial adhesion between the fiber and PP matrix. The grafting of the fibers by MAPP enhances the tensile strength of the resulting composite. It has been found that the urethane derivative of polypropylene glycol and cardanol treatments reduced the hydrophilic nature of sisal fiber and thereby enhanced the tensile properties of the sisal–PP composites, as evident from the SEM photomicrographs of the fracture surface. The IR spectrum of the urethane derivative of polypropylene glycol gave evidence for the existence of a urethane linkage. Benzoylation of the fiber improves the adhesion of the fiber to the PP matrix. The benzoylated fiber was analyzed by IR spectroscopy. Experimental results indicated a better compatibility between benzoylated fiber and PP. The observed enhancement in tensile properties of permanganate-treated composites at a low concentration is due to the permanganate-induced grafting of PP on to sisal fibers. Among the various treatments, MAPP treatment gave superior mechanical properties. Finally, experimental results of the mechanical properties of the composite have been compared with theoretical predictions.     

Fabrication and Flexural Properties of Bagasse Fiber Reinforced Biodegradable Composites

Biodegradable composites made from bagasse fiber and biodegradable resin were fabricated and the flexural properties of the composites investigated in terms of the effects of fiber length, fiber volume fraction, and different alkali treatments of the bagasse fibers. The flexural properties of the composites increased with the increase in fiber length but decreased below the critical fiber length. The flexural properties increased with the increase in fiber volume fraction. The scanning electron microscope (SEM) micrographs showed that compression of the cellulose structure of bagasse fiber after preparation could have caused enhancement in the flexural properties. Furthermore, when comparing the effects of different alkali treatments of the bagasse fibers, maximum improvement in the flexural properties was observed for the 1% NaOH solution treated fiber composites. After alkali treatment, fibrillation occurred and the surface of the treated fibers became finer; this could contribute to improvement in the fiber‐matrix adhesion and result in enhancing the flexural properties.     

Synergistic Effect of Polyhedral Oligomeric Silsesquioxane and Multiwalled Carbon Nanotubes on the Flame Retardancy and the Mechanical and Thermal Properties of Epoxy Resin

A novel polyhedral oligomeric silsesquioxane containing phosphorus and boron (PB-POSS) was synthesized. The resulting PB-POSS and multiwalled carbon nanotubes (MWCNTs) were incorporated into an epoxy resin (EP) to prepare PB-POSS/MWCNTs/EP composites through a solution mixing method. The synergistic effect of MWCNTs and PB-POSS on the thermal and mechanical properties and the flame retardancy of these flame retardant composites were studied. The experimental results showed that the introduction of PB-POSS or MWCNTs further improved the LOI values of the epoxy resin, and the highest LOI value (32.8%) was obtained for the formulation containing 14.6 wt% PB-POSS and 0.4 wt% MWCNTs. In addition, the incorporation of both PB-POSS and MWCNTs significantly improved the thermal and mechanical properties of the composites. The mechanical properties of composites containing 14.7 wt% PB-POSS and 0.3 wt% MWCNTs reached the maximum. The impact strength and flexural strength increased by 42% and 7%, respectively, compared to the neat epoxy resin. Thus, a combination of PB-POSS and MWCNTs in the appropriate ratio could effectively enhance the thermal and mechanical properties and the flame retardancy of the epoxy resin matrix.