Electrocatalytic performance of fuel oxidation by Pt3Ti nanoparticles

A Pt-based electrocatalyst for direct fuel cells, Pt3Ti, has been prepared in the form of nanoparticles. Pt(1,5-cyclooctadiene)Cl2 and Ti(tetrahydrofuran)2Cl4 are reduced by sodium naphthalide in tetrahydrofuran to form atomically disordered Pt3Ti nanoparticles (FCC-type structure: Fm3m; a = 0.39 nm; particle size = 3 +/- 0.4 nm). These atomically disordered Pt3Ti nanoparticles are transformed to larger atomically ordered Pt3Ti nanoparticles (Cu3Au-type structure: Pm3m; a = 0.3898 nm; particle size = 37 +/- 23 nm) by annealing above 400 degrees C. Both atomically disordered and ordered Pt3Ti nanoparticles show lower onset potentials for the oxidation of formic acid and methanol than either pure Pt or Pt-Ru nanoparticles. Both atomically disordered and ordered Pt3Ti nanoparticles show a much lower affinity for CO adsorption than either pure Pt or Pt-Ru nanoparticles. Atomically ordered Pt3Ti nanoparticles show higher oxidation current densities for both formic acid and methanol than pure Pt, Pt-Ru, or atomically disordered Pt3Ti nanoparticles. Pt3Ti nanoparticles, in particular the atomically ordered materials, have promise as anode catalysts for direct fuel cells.     

Pt/PAn/Ti电极的制备及对甲醛的电催化氧化

通过循环伏安的电化学方法在金属钛基体上先后进行苯胺的聚合和金属铂的电化学沉积,得到以金属钛为基体的聚苯胺载铂电极(Pt/PAn/Ti),并通过扫描电镜和循环伏安法对该电极进行了表征。通过研究甲醛在该电极上的电催化氧化行为,考察了载铂量对甲醛氧化效果的影响及PAn在电催化氧化甲醛的过程中所起的作用。结果表明,载铂量与甲醛的氧化有一定的关系,PAn的存在使得铂微粒分散程度更好,有效面积更大,与相同铂沉积量的Pt/Ti电极相比,甲醛在其上的正向扫描氧化峰电流密度增加了2.3倍,电位负移了40mV;反向扫描氧化峰电流密度增加了5倍,电位负移了30mV。同时,PAn的存在也增强了电极的抗中毒能力。     

Electrocatalytic activity of sol-gel-prepared RuO2/Ti anode in chlorine and oxygen evolution reactions

Electrocatalytic properties of RuO₂/Ti anode with different coating masses, which are prepared by the alkoxide sol-gel procedure, are investigated in chlorine and oxygen evolution reactions by polarization measurements and electrochemical impedance spectroscopy in H₂SO₄ and NaCl electrolytes. According to polarization measurements, the activity of anodes at overpotentials below 100 mV is independent of coating mass. However, impedance measurements above 100 mV reveal changes in the activity of anodes in chlorine evolution reaction for different coating masses. The diffusion limitations related to the evolved chlorine are registered in low-frequency domain at 1.10 V (SCE), diminishing with the increase in potential to the 1.15 V (SCE). The observed impedance behavior is discussed with respect to the activity model for activated titanium anodes in chlorine evolution reaction involving formation of gas channels within porous coating structure. Gas channels enhance the mass transfer rate similarly to the forced convection, which also increases the activity of anode. This is more pronounced for the anode of greater coating mass due to its more compact surface structure. The more compact structure appears to be beneficial for gas channels formation. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 10, pp. 1173–1179. The text was submitted by the authors in English.     

Insights into the electrochemical degradation of sulfamethoxazole and its metabolite by Ti/SnO2-Sb/Er-PbO2 anode

Electrochemical degradation of sulfamethoxazole (SMX) and its metabolite acetyl-sulfamethoxazole (Ac-SMX) by Ti/SnO₂-Sb/Er-PbO₂ were investigated. Results indicated that the electrochemical degradation of SMX and Ac-SMX followed pseudo-first-order kinetics. The rate constants of SMX and Ac-SMX were 0.268 and 0.072 min^-1 at optimal current density of 10 and 14 mA/cm², respectively. Transformation products of SMX and Ac-SMX were identified and the possible degradation pathways, including the cleavage of S-N bond, opening ring of isoxazole and nitration of amino group, were proposed. Total organic carbon removal of SMX was nearly 63.2% after 3 h electrochemical degradation. 22.4% nitrogen of SMX was transformed to NO₃^-, and 98.8% sulfur of SMX was released as SO₄^2-. According to quantitative structure-activity relationship model, toxicities of SMX and Ac-SMX to aquatic organisms significantly decreased after electrochemical degradation. Electric energy consumption for 90% SMX and Ac-SMX degradation was determined to be 0.58-8.97 and 6.88-44.19 Wh/L at different experimental conditions, respectively. Compared with parent compound SMX, the metabolite Ac-SMX is more refractory and toxic, which emphasizes the importance of taking its metabolites into account when investigating the disposal of pharmaceuticals from wastewater.     

Characterisation and properties of magnetron sputtered nanoscale bi‐layered Ni/Ti thin films and effect of annealing

Single‐bi‐layer of Ni–Ti thin film was deposited using DC and RF magnetron sputtering technique by layer‐wise deposition of Ni and Ti on Si(100) substrate in the order of Ni as the bottom layer and Ti as the top layer. The deposition of these amorphous as‐deposited thin films was followed by annealing at 300 °C, 400 °C, 500 °C, and 600 °C temperature with 1‐h annealing time for each to achieve crystalline thin films. This paper describes the fabrication processes and the novel characterization techniques of the as‐deposited as well as the annealed thin films. Microstructures were analysed using FESEM and HRTEM. Nano‐indentation and AFM were carried out to characterize the mechanical properties and surface profiles of the films. It was found that, for the annealing temperatures of 300 °C to 600 °C, the increase in annealing temperature resulted in gradual increase in atomic‐cluster coarsening with improved ad‐atom mobility. Phase analyses, performed by GIXRD, showed the development of silicide phases and intermetallic compounds. Cross‐sectional micrographs exhibited the inter‐diffusion between the two‐layer constituents, especially at higher temperatures, which resulted either in amorphization or in crystallization after annealing at temperatures above 400 °C. Copyright © 2015 John Wiley & Sons, Ltd.     

The diffusion of Pt in BST films on Pt/Ti/SiO2/Si substrate by sol-gel method

Barium strontium titanate (Ba_0.65Sr_0.35TiO₃) ferroelectric thin films have been prepared by sol-gel method on Pt/Ti/SiO₂/Si substrate. The X-ray diffraction (XRD) pattern indicated that the films were a polycrystalline perovskite structure and the atomic force microscope (AFM) image showed that the crystallite size and the root mean square roughness (RMS) were 90 nm and 3.6 nm, respectively. The X-ray photoelectron spectrum (XPS) images showed that Pt consisting in BST thin films was the metallic state, and the Auger electron spectroscopy (AES) analysed the Pt concentration in different depth profiles of BST thin films. The result displayed that the Pt diffusion in BST thin film is divided into two regions: near the BST/Pt interface, the diffusion type was volume diffusion, and far from the interface correspondingly, the diffusion type became grain boundary diffusion. In this paper, the previous researcher’s result was used to verify our conclusion.     

Photocatalytic membrane processes for degradation of various types of organic pollutants and micropollutants in water

Degradation tests in a photocatalytic membrane system have been carried out using TiO2 (Degussa P25) as catalyst and humic acid, organic dyes, 4-nitrophenol as pollutants. The influence of UV radiation and initial concentration of pollutant on the photodegradation rate were investigated in discontinuous and continuous systems. Experimental results showed that it is possible to obtain an efficient photocatalytic membrane process, but various parameters (e.g. pH) should be optimised to obtain high reaction rate and high membrane rejection of pollutants and their by-products.     

Growth,characterization and interfacial reaction of magnetron sputtered Pt/CeO2 thin films on Si and Si3N4 substrates

Growth of magnetron sputtered Pt/CeO₂ thin films on Si and Si₃N₄ were characterized by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and X‐ray photoelectron spectroscopy (XPS). Interaction of Pt/CeO₂ films with Si on Si and Si₃N₄ substrates was extensively investigated by XPS. XRD studies show that films are oriented preferentially to (200) direction of CeO₂. XPS results show that Pt is mainly present in +2 oxidation state in Pt/CeO₂/Si film, whereas Pt⁴⁺ predominates in Pt/CeO₂/Si₃N₄ film. Concentration of Pt⁴⁺ species is more than four times on Si₃N₄ substrate as compared with that on Si. Ce is present as both +4 and +3 oxidation states in Pt/CeO₂ films deposited on Si and Si₃N₄ substrates, but concentration of Ce³⁺ species is more in Pt/CeO₂/Si film. Interfacial reaction between CeO₂ and Si substrate is controlled in the presence of Pt. Pt/Ce concentration ratio decreases in Pt/CeO₂/Si₃N₄ film upon successive sputtering, whereas this ratio decreases initially and then increases in Pt/CeO₂/Si film. Copyright © 2015 John Wiley & Sons, Ltd.     

钌钯氧化物涂层电极光电降解活性红3BS的研究

光电催化技术作为一种新型的高级氧化过程日益受到重视,并在废水处理中起到重要作用。目前光电降解技术的研究主要集中于半导体电极作为阳极的光电体系中。本文以活性红3BS为模型反应物,自行烧制钌钯氧化物涂层电极为阳极,进行了光电脱色染料的实验研究,并对其可能机理做了初步的探讨。     

Electrocatalytic oxidation of methanol on Pt/NiZn electrode in alkaline medium

In this study, a platinum electrode was coated with NiZn layer (Pt/NiZn) in a nickel-zinc bath by electrodeposition for use as anode material for methanol electrooxidation in alkaline solution. The electrode prepared was etched in a concentrated alkaline solution (30% NaOH) to produce a porous and electrocatalytic surface suitable for use in the methanol electrooxidation (Pt/NiZn). The surface morphologies and compositions of coating before and after alkaline leaching were determined by energy dispersive X-ray (EDX) and scanning electron microscopy (SEM) techniques. The effect of NiZn coated platinum electrode for methanol electrooxidation was investigated in 1 M NaOH solution by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques. Methanol electrooxidation on Pt/NiZn electrode was studied at various temperatures and potential scan rates. The results showed that Pt/NiZn electrode behaved as an efficient catalyst for the electrooxidation of methanol in alkaline medium.     

Formation of NiO/YSZ functional anode layers of solid oxide fuel cells by magnetron sputtering

The decrease in the polarization resistance of the anode of solid-oxide fuel cells (SOFCs) due to the formation of an additional NiO/(ZrO₂ + 10 mol % Y₂O₃) (YSZ) functional layer was studied. NiO/YSZ films with different NiO contents were deposited by reactive magnetron sputtering of Ni and Zr–Y targets. The elemental and phase composition of the films was adjusted by regulating oxygen flow rate during the sputtering. The resulting films were studied by scanning electron microscopy and X-ray diffractometry. Comparative tests of planar SOFCs with a NiO/YSZ anode support, NiO/YSZ functional nanostructured anode layer, YSZ electrolyte, and La_0.6Sr_0.4Co_0.2Fe_0.8O₃/Ce_0.9Gd_0.1O₂ (LSCF/CGO) cathode were performed. It was shown that the formation of a NiO/YSZ functional nanostructured anode leads to a 15–25% increase in the maximum power density of fuel cells in the working temperature range 500–800°C. The NiO/YSZ nanostructured anode layers lead not only to a reduction of the polarization resistance of the anode, but also to the formation of denser electrolyte films during subsequent magnetron sputtering of electrolyte.     

Electrocatalytic Activity of Pt/C Electrodes for Ethanol Oxidation in Vapor Phase

Introduction The selective oxidation of ethanol to acetaldehydeis of special interest in the areas where biomass-basedeconomics are under development since acetaldehydecan be used for the syntheses of other basic chemicalssuch as acetic acid, acetic anhydride,n-butanol,etc.[1—6]. With the advancement of fuel cell technologyand electrocatalysis stimulated by the world energy andraw material situation, some special opportunities havebeen provided for investigating electrosynthesis of or-ganic c…     

Photocatalytic degradation of high ammonia concentration water solutions by TiO2

Recent studies reported the use of suspended TiO2 powder as photo catalyst in the degradation process of several organic and inorganic substances in water, like chlorinated hydrocarbons, alkyl- and alkanoloammines and ammonia. In order to evaluate the possibility of using this method for a further removal of ammonia from wastewater after a biological nitrification/denitrification treatment, a kinetic study of photo oxidation over TiO2 of NH3/NH4 in the high concentration range of 26 - 214 mg/I, has been carried out. Effects of pH, TiO2, ammonium and dissolved O2 concentration on the degradation efficiency and reaction products distribution (NO2-, NO3- e N2) were studied. The results have shown that, at a catalyst concentration of 0.012% (p/v), the photo catalytic oxidation of ammonia can be described with the Langumuir- Hinshelwood kinetic model, as reported by several authors.     

纳米PbO/Ti电极催化还原偏硼酸锂制备硼氢化锂

在乙二醇甲醚溶液中电解铅片,制备了铅醇盐配合物,然后将溶液直接水解、凝胶,再通过提拉法涂抹在钛丝表面,450 ℃煅烧2 h制备纳米PbO/Ti电极。 将PbO/Ti电极在0.2~1.0 mol/L LiOH+0.1~0.5 mol/L LiBO2溶液测试催化还原性能,研究了影响电解还原LiBO2制备硼氢化锂(LiBH4)的主要因素,如LiBO2和LiOH浓度等。 通过X射线粉末衍射和扫描电子显微镜对PbO/Ti电极和LiBH4进行了表征。 实验表明,纳米PbO/Ti电极表面颗粒分散较好,修饰电极催化性能稳定,放电电流较大,产率和电流效率分别达15.6%和25.3%。     

掺杂PbO2/Ti阳极在硫酸铬电氧化过程的电极行为

PbO2/Ti 电极具有耐腐蚀性能好、导电性强、析氧过电位高等优点,已成功地应用在无机和有机化合物电解生产、环境污染控制、阴极保护以及电浮选等方面[1-3].     

Quantification and confirmation of priority organic micropollutants in water by LC-tandem mass spectrometry

Liquid chromatography coupled to tandem mass spectrometry with a triple quadrupole analyser was used to determine selected (medium) polar organic pollutants—isoproturon, diuron and pentachlorophenol, as the herbicides simazine, atrazine, terbuthilazine, alachlor, and metolachlor—in treated water from urban solid-waste leachates. Two millilitres of water was preconcentrated by on-line trace enrichment (solid-phase extraction liquid chromatography) which allowed rapid analysis, but still with a satisfactory sensitivity, as the limits of quantification were 0.05?µg?L^?1, while the limits of detection were in the range of 0.001–0.01?µg?L^?1. Confirmation of the identity of compounds was ensured by the use of two tandem mass spectrometry transitions. Moreover, a study of matrix effects was thoroughly investigated by applying the developed procedure to different ground and surface waters. A simple dilution of the water sample with high-performance-liquid-chromatography-grade water was sufficient to minimize and/or remove this undesirable effect in all water samples tested, this approach being feasible due to the excellent sensitivity of the method.     

MIL-101(Cr)-decorated Ti/TiO2 anode for electrochemical oxidation of aromatic pollutants from water

Hydroxyl radicals (^?OH) generated on anode play a vital role in electrochemical oxidation (EO) of organic pollutants for water treatment. Inspired by the four-electron oxygen evolution reaction (OER), we supposed an anode-selection strategy to stabilize deeply oxidized states (*O and *OOH) which are beneficial to generating ^?OH. To verify the hypothesis, a candidate anode component (MIL-101(Cr), a well-known metal-organic framework with active variable-valence transition metal centers) was used to coat Ti/TiO₂ plate to fabricate anodes. Compared to TiO₂(101) plane on undecorated anode surface, fast and complete removal of aniline and phenol, and improved energy utilization were achieved on MIL-101(Cr)-coated-Ti/TiO₂ anode. Mechanism investigation, including pollutant degradation pathways, showed the predominate contribution (69.60%–75.13%) of ^?OH in pollutant mineralization. Density functional theory (DFT) computations indicated Cr site in MIL-101(Cr) was more conducive to stabilizing *O and *OOH, leading to thermodynamical spontaneous generation of ^?OH. This work opens up an exciting avenue to explore ^?OH production, and supplies a useful guidance to the development of anode materials for EO process.     

Photoelectrocatalytic performance of conductive carbon black-modified Ti/F-PbO2 anode for degradation of dye wastewater (reactive brilliant blue KN-R)

Journal of Solid State Electrochemistry - The conductive carbon black (CCB)-modified Ti/F-PbO2 electrodes were prepared by electrodeposition and characterized systemically using SEM, EDS, XRD, and...     

Optimization of Graphene Layers Grown on Pt/Ti/SiO2 by Hot Filament Chemical Vapor Deposition

Large area single and bilayer graphene are grown on Pt/Ti/SiO₂ substrates by hot filament chemical vapor deposition (HFCVD) with and without the assistance of Cu foil. The quality and number of graphene layers deposited on the substrate are assessed by Raman Spectroscopy. Atomic Force Microscopy (AFM) is used for assessing the surface topography of the graphene films grown on the Pt/Ti/SiO₂ substrates. The microstructure and elemental analyses are performed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). The results show that bilayer graphene growth is facilitated by a copper foil placed nearby Pt/Ti/SiO2 substrate and by a high filament temperature in the HFCVD reactor. Monolayer graphene grows only when no copper foil is placed near the Pt/Ti/SiO₂ substrate at a low filament temperature. The approach paves a novel pathway towards the layer-controlled growth of graphene on Pt/Ti/SiO₂ substrates by HFCVD for frontier applications.