Long‐Life Room‐Temperature Sodium–Sulfur Batteries by Virtue of Transition‐Metal‐Nanocluster–Sulfur Interactions

Room‐temperature sodium–sulfur (RT‐Na/S) batteries hold significant promise for large‐scale application because of low cost of both sodium and sulfur. However, the dissolution of polysulfides into the electrolyte limits practical application. Now, the design and testing of a new class of sulfur hosts as transition‐metal (Fe, Cu, and Ni) nanoclusters (ca. 1.2 nm) wreathed on hollow carbon nanospheres (S@M‐HC) for RT‐Na/S batteries is reported. A chemical couple between the metal nanoclusters and sulfur is hypothesized to assist in immobilization of sulfur and to enhance conductivity and activity. S@Fe‐HC exhibited an unprecedented reversible capacity of 394 mAh g^?1 despite 1000 cycles at 100 mA g^?1, together with a rate capability of 220 mAh g^?1 at a high current density of 5 A g^?1. DFT calculations underscore that these metal nanoclusters serve as electrocatalysts to rapidly reduce Na₂S₄ into short‐chain sulfides and thereby obviate the shuttle effect.     

Electrospun cellulose acetate/poly(vinylidene fluoride) nanofibrous membrane for polymer lithium-ion batteries

The membranes for gel polymer electrolyte (GPE) for lithium-ion batteries were prepared by electrospinning a blend of poly(vinylidene fluoride) (PVdF) with cellulose acetate (CA). The performances of the prepared membranes and the resulted GPEs were investigated, including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), porosity, hydrophilicity, electrolyte uptake, mechanical property, thermal stability, AC impedance measurements, linear sweep voltammetry, and charge–discharge cycle tests. The effect of the ratio of CA to PVdF on the performance of the prepared membranes was considered. It is found that the GPE based on the blended polymer with CA:PVdF =2:8 (in weight) has an outstanding combination property-strength (11.1 MPa), electrolyte uptake (768.2 %), thermal stability (no shrinkage under 80 °C without tension), and ionic conductivity (2.61 × 10^?3 S cm^?1). The Li/GPE/LiCoO₂ battery using this GPE exhibits superior cyclic stability and storage performance at room temperature. Its specific capacity reaches up to 204.15 mAh g^?1, with embedded lithium capacity utilization rate of 74.94 %, which is higher than the other lithium-ion batteries with the same cathode material LiCoO₂ (about 50 %).     

A Stable Quasi‐Solid‐State Sodium–Sulfur Battery

Ambient‐temperature sodium–sulfur (Na–S) batteries are considered a promising energy storage system due to their high theoretical energy density and low costs. However, great challenges remain in achieving a high rechargeable capacity and long cycle life. Herein we report a stable quasi‐solid‐state Na‐S battery enabled by a poly(S‐pentaerythritol tetraacrylate (PETEA))‐based cathode and a (PETEA‐tris[2‐(acryloyloxy)ethyl] isocyanurate (THEICTA))‐based gel polymer electrolyte. The polymeric sulfur electrode strongly anchors sulfur through chemical binding and inhibits the shuttle effect. Meanwhile, the in situ formed polymer electrolyte with high ionic conductivity and enhanced safety successfully stabilizes the Na anode/electrolyte interface, and simultaneously immobilizes soluble Na polysulfides. The as‐developed quasi‐solid‐state Na‐S cells exhibit a high reversible capacity of 877 mA h g^?1 at 0.1 C and an extended cycling stability.     

PVDF/PAN/SiO<Subscript>2</Subscript> polymer electrolyte membrane prepared by combination of phase inversion and chemical reaction method for lithium ion batteries

PVDF/PAN/SiO₂ polymer electrolyte membranes based on non-woven fabrics were prepared via introducing a chemical reaction into Loeb-Sourirajan (L-S) phase inversion process. It was found that physical properties (porosity, electrolyte uptake and ionic conductivity) and electrochemical properties were obviously improved. A favorable membrane structure with fully connective porous and uniform pore size distribution was obtained. The effects of PVDF/PAN weight ratio on the morphology, crystallinity, porosity, and electrochemical performances of membranes were studied. The optimized PVDF/PAN (70/30 w/w) (designated as M_pc30) polymer electrolyte membrane delivered excellent electrolyte uptake of 246.8 % and the highest ionic conductivity of 3.32 × 10^?3 S/cm with electrochemical stability up to 5.0 V (vs. Li/Li⁺). In terms of cell performance, the Li/M_pc30 polymer electrolyte/LiFePO₄ battery exhibited satisfactory electrochemical properties including high discharge capacity of 149 mAh/g at 0.2 C rate and good discharge performance at different current densities. The promising results reported here clearly indicated that PVDF/PAN/SiO₂ polymer electrolyte membranes prepared by the combination of phase inversion and chemical reaction method were promising enough to be applied in power lithium ion batteries.     

Enhanced Performance of a Lithium–Sulfur Battery Using a Carbonate‐Based Electrolyte

The lithium–sulfur battery is regarded as one of the most promising candidates for lithium–metal batteries with high energy density. However, dendrite Li formation and low cycle efficiency of the Li anode as well as unstable sulfur based cathode still hinder its practical application. Herein a novel electrolyte (1 m LiODFB/EC‐DMC‐FEC) is designed not only to address the above problems of Li anode but also to match sulfur cathode perfectly, leading to extraordinary electrochemical performances. Using this electrolyte, lithium|lithium cells can cycle stably for above 2000 hours and the average Coulumbic efficiency reaches 98.8 %. Moreover, the Li–S battery delivers a reversible capacity of about 1400 mAh g^?1_sulfur with retention of 89 % for 1100 cycles at 1 C, and a capacity above 1100 mAh g^?1_sulfur at 10 C. The more advantages of this cell system are its outstanding cycle stability at 60 °C and no self‐discharge phenomena.     

A Four‐Electron Sulfur Electrode Hosting a Cu2+/Cu+ Redox Charge Carrier

The elemental sulfur electrode with Cu²⁺ as the charge carrier gives a four‐electron sulfur electrode reaction through the sequential conversion of S?CuS?Cu₂S. The Cu‐S redox‐ion electrode delivers a high specific capacity of 3044 mAh g^?1 based on the sulfur mass or 609 mAh g^?1 based on the mass of Cu₂S, the completely discharged product, and displays an unprecedently high potential of sulfur/metal sulfide reduction at 0.5 V vs. SHE. The Cu‐S electrode also exhibits an extremely low extent of polarization of 0.05 V and an outstanding cycle number of 1200 cycles retaining 72 % of the initial capacity at 12.5 A g^?1. The remarkable utility of this Cu‐S cathode is further demonstrated in a hybrid cell that employs an Zn metal anode and an anion‐exchange membrane as the separator, which yields an average cell discharge voltage of 1.15 V, the half‐cell specific energy of 547 Wh kg^?1 based on the mass of the Cu₂S/carbon composite cathode, and stable cycling over 110 cycles.     

Sucrose assisted hydrothermal synthesis of SnO2/graphene nanocomposites with improved lithium storage properties

SnO₂/graphene nanocomposites are synthesized by a new hydrothermal treatment strategy under the assistance of sucrose. From the images of the scanning electron microscope (SEM) and transmission electron microscope (TEM), it can be observed that SnO₂ nanoparticles with the size of 4~5 nm uniformly distribute on the graphene nanosheets. The result demonstrates that sucrose can effectively prevent graphene nanosheets from restacking during hydrothermal treatment and subsequently treatment. The charging/discharging test result indicates that the SnO₂/graphene nanocomposites exhibit high specific capacity and excellent cycleability. The first reversible specific capacity is 729 mAh.g^?1 at the current density of 50 mA.g^?1, and remains 646 mAh.g^?1 after 30 cycles at the current density of 100 mA.g^?1, 30 cycles at the current density of 200 mA.g^?1, 30 cycles at the current density of 400 mA.g^?1, 30 cycles at the current density of 800 mA.g^?1, and 30 cycles at the current density of 50 mA.g^?1.     

Rechargeable Room‐Temperature Na–CO2 Batteries

Developing rechargeable Na–CO₂ batteries is significant for energy conversion and utilization of CO₂. However, the reported batteries in pure CO₂ atmosphere are non‐rechargeable with limited discharge capacity of 200 mAh g^?1. Herein, we realized the rechargeability of a Na–CO₂ battery, with the proposed and demonstrated reversible reaction of 3 CO₂+4 Na?2 Na₂CO₃+C. The battery consists of a Na anode, an ether‐based electrolyte, and a designed cathode with electrolyte‐treated multi‐wall carbon nanotubes, and shows reversible capacity of 60000 mAh g^?1 at 1 A g^?1 (≈1000 Wh kg^?1) and runs for 200 cycles with controlled capacity of 2000 mAh g^?1 at charge voltage <3.7 V. The porous structure, high electro‐conductivity, and good wettability of electrolyte to cathode lead to reduced electrochemical polarization of the battery and further result in high performance. Our work provides an alternative approach towards clean recycling and utilization of CO₂.     

Activated carbon aerogels with high bimodal porosity for lithium/sulfur batteries

Activated carbon aerogels (ACAs) with high bimodal porosity were obtained for lithium/sulfur batteries by potassium hydroxide (KOH) activation. Then sulfur–activated carbon aerogels (S–ACAs) composites were synthesized by chemical deposition strategy. The S–ACAs composites were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy, and N₂ adsorption/desorption measurements. It is found that the activated carbon aerogels treated by KOH activation presents a porous structure, and sulfur is embedded into the pores of the ACAs network-like matrix after a chemical deposition process. The Li/S–ACAs (with 69.1 wt% active material) composite cathode exhibits discharge capacities of 1,493 mAh g^?1 in the first cycle and 528 mAh g^?1 after 100 cycles at a higher rate of C/5 (335 mA g^?1). The S–ACAs composite cathode exhibits better electrochemical reversibility, higher active material utilization, and less severe polysulfide shuttle than S–CAs composite cathode because of high bimodal porosity structure of the ACAs matrix.     

Synthesis of γ-LiV2O5 nanorods as a high-performance cathode for Li ion battery

One-dimension γ-LiV₂O₅ nanorods were synthesized using VO₂(B) nanorods as precursor in this study. The as-prepared material is characterized by X-ray diffraction, X-ray photoelectron spectrometry, Fourier-transform infrared, transmission electron microscopy (TEM), cyclic voltammetry, and charge–discharge cycling test. TEM results show that LiV₂O₅ nanorods are 90–250 nm in diameter. The nanorods deliver a maximum discharge capacity of 284.3 mAh g^?1 at 15 mA g^?1 and 270.2 mAh g^?1 is maintained at the 15th cycle. Good rate performance is also observed with the discharge capacity of 250.1 and 202.6 mAh g^?1 at 50 and 300 mA g^?1, respectively. The capacity retention at 300 mA g^?1 is 84.2% over 50 cycles. The Li⁺ diffusion coefficient of LiV₂O₅ is calculated to be 10^-10–10^?9 cm² s^?1. It is demonstrated that the nanorod morphology could greatly facilitate to shorten lithium ion diffusion pathways and increase the contact area between active material and electrolyte, resulting in high capacity and rate performance for LiV₂O₅.     

Study of quasi-solid electrolyte in dye-sensitized solar cells using surfactant as pore-forming materials in TiO<Subscript>2</Subscript> photoelectrodes

A novel polymer gel electrolyte was used to improve the performance and long-term stability in dye-sensitized solar cells (DSSCs). The polymer gel electrolyte (PGE) was prepared by mixing 5 wt% poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and 2 % TiO₂ nanoparticles. The conductivity of PGE with P25 reached 9.98 × 10^?3 S/cm, which increased by 34.9 % compared with 7.40 × 10^?3 S/cm of PGE without P25, and the diffusion coefficient was also increased by 19.0 %. Different photoelectrodes were obtained by using three kinds of surfactants (cetylamine, octadecylamine, and P123) as pore-forming materials, and their morphologies were contrasted through scanning electron microscopy (SEM). The results showed that gel electrolyte can increase the short-circuit current density (J _sc) from 11.01 to 12.99 mA/cm² in DSSCs. Moreover, unlike the liquid electrolyte, the gel electrolyte is more conducive to the TiO₂ photoelectrodes with larger pores. In conclusion, the efficiency of DSSC with gel electrolyte and P123 as pore-forming material was 6.73 %, which was 12 % higher than the liquid electrolyte in the same test condition. In addition, the sealed gel electrolyte DSSCs showed better stability than did liquid electrolyte DSSCs during nearly 600 h.     

Tin oxide-titanium oxide/graphene composited as anode materials for lithium-ion batteries

A tin oxide-titanium oxide/graphene (SnO₂-TiO₂/G) ternary nanocomposite as high-performance anode for Li-ion batteries was prepared via a simple reflux method. The graphite oxide (GO) was reduced to graphene nanosheet, and the SnO₂-TiO₂ nanocomposites were evenly distributed on the graphene matrix in the SnO₂-TiO₂/G nanocomposite. The as-prepared SnO₂-TiO₂/G nanocomposites were employed as anode materials for lithium-ion batteries, showing an outstanding performance with high reversible capacity and long cycle life. The composite delivered a superior initial discharge capacity of 1,594.6 mAh g^?1 and a reversible specific capacity of 1,500.3 mAh g^?1 at a current density of 100 mA g^?1. After 100 cycles, the reversible discharge capacity was still maintained at 1,177.4 mAh g^?1 at a current density of 100 mA g^?1 with a high retained rate of reversible capacity of 73.8 %. The addition of small amount of TiO₂ nanoparticles improved the cycling stability and specific capacity of SnO₂-TiO₂/G nanocomposite, obviously. The results demonstrate that the SnO₂-TiO₂/G nanocomposite is a promising alternative anode material for practical Li-ion batteries.     

Hybrids of MnO<Subscript>2</Subscript> nanoparticles anchored on graphene sheets as efficient sulfur hosts for high-performance lithium sulfur batteries

Lithium–sulfur (Li–S) battery is considered as a promising option for electrochemical energy storage applications because of its low-cost and high theoretical capacity. However, the practical application of Li–S battery is still hindered due to the poor electrical conductivity of S cathode and the high dissolution/shuttling of polysulfides in electrolyte. Herein, we report a novel physical and chemical entrapment strategy to address these two problems by designing a sulfur–MnO₂@graphene (S–MnO₂@GN) ternary hybrid material structure. The MnO₂ particles with size of ~ 10 nm are anchored tightly on the wrinkled and twisted GN sheets to form a highly efficient sulfur host. Benefiting from the synergistic effects of GN and MnO₂ in both improving the electronic conductivity and hindering polysulfides by physical and chemical adsorptions, this unique S–MnO₂@GN composite exhibits excellent electrochemical performances. Reversible specific capacities of 1416, 1114, and 421 mA h g^?1 are achieved at rates of 0.1, 0.2, and 3.2 C, respectively. After a 100 cycle stability test, S–MnO₂@GN composite cathode could still maintain a reversible capacity of 825 mA h g^?1.     

Gel Polymer Electrolytes with Talc as a Natural Mineral Filler and a Biodegradable Polymer Matrix in Sodium-Ion Batteries

A gel polymer electrolyte based on poly(vinyl alcohol) (PVA) is used in sodium-ion batteries (SIBs). The use of biodegradable and water-soluble polymer potentially reduces the negative environmental impact. The other components include sodium salt (NaPF₆), sulfolane (TMS) as a plasticizer and talc. For the first time, natural and abundant talc has been used as an inert filler in a gel polymer electrolyte. The best results were obtained for moderate amounts of filler (1 and 3 wt%). Then, an increase in the conductivity, transference numbers, and thermal stability of the membranes was observed. Moreover, the presence of talc had a positive effect on the cyclability of the hard carbon electrode. The discharge capacity after 50 cycles of HC|1 % T_TMS|Na and HC|3 % T_TMS|Na was 243 and 225 mAh g⁻¹, respectively. The use of talc in gel polymer electrolytes containing sodium ions improves the safety and efficiency of SIBs.     

Polymer battery R&D in the U.S.

Polymer electrolytes that have been developed for battery applications fall into two general classes, neat or “pure” polymer and plasticized or gel in which the polymer is combined with a conducting organic electrolyte. The polyethylene oxide (PEO) and its modifications are typical of the “pure” polymer electrolytes. They have poor conductivity at room temperatures, but at elevated temperatures, their conductivity is of the order of 10⁻³ to 10⁻⁴ S/cm. The PEO electrolytes have found application in the high temperature (>60°C) lithium metal anode battery systems. The high temperature necessary for good operation makes them unsuitable for use in small consumer appliances. The polymer electrolyte battery development activities have resulted in several high performance battery systems now just entering the market. Not all of the developments have resulted in commercial cell production. The commercialization activities of high performance lithium‐ion (Li‐Ion) batteries have been based on two general plastic polymer systems: poly‐vinylidene difluoride‐hexafluoropropylene copolymer (PVdF‐HFP) and polyacrylates. The polymer cells are expected to have advantages in manufacturing, flexibility, thin cell formats and lightweight packaging. Important parameters in PVdF gel electrolyte performance include the electrolyte type (combination of organic carbonates), temperature, and HFP copolymer content. Li‐Ion coin cells fabricated with a polyolefin separator with either liquid electrolyte or with the PVdF gel polymer electrolyte have equivalent performance.     

Self-assembled reduced graphene oxide/sulfur composite encapsulated by polyaniline for enhanced electrochemistry performance

Reduced graphene oxide/sulfur/polyaniline (referred to RGO/S/PANI) composite was self-assembled through in situ synthesis and used to investigate the electrochemical properties of lithium/sulfur cells. The RGO/S/PANI composite possessed 809.3/801.9 mAh g^?1 of initial charge/discharge capacities, higher than 588.3/588.2 mAh g^?1 for reduced graphene oxide/sulfur (referred to RGO/S) and 681.4/669.9 mAh g^?1 for sulfur/polyaniline (referred to S/PANI) at similar conditions. The RGO/S/PANI composite obtained 400 mAh g^?1 at 2 C and good reversible capacities of 605.5 and 600.8 mAh g^?1 at 100th charge/discharge cycle at 0.1 C, in comparison with low electrochemical performance of RGO/S and S/PANI. The improved properties could be attributed to the collaboration of RGO and PANI. Co-generation of RGO and sulfur acted as seeds for their depositions, stimulated their uniform distributions, and restricted the agglomeration of sulfur particles in situ synthesis. Polyaniline coated RGO/S and stabilized the nanostructure of RGO/S/PANI in repeated charge/discharge cycles. In addition, RGO and PANI provided many electron channels to enhance sulfur conductivity and sufficient void space for sulfur swelling during charge/discharge cycles.     

Polyacrylamide-methanesulfonic acid gel polymer electrolytes for tin-air battery

The present work describes the synthesis and characterization of gel polymer electrolytes containing methanesulfonic acid (MSA) with Polyacrylamide (PAAm). The PAAm–MSA gel electrolytes were prepared with different concentrations of MSA. Addition of 0.5 M of MSA into the electrolyte increased the ionic conductivity of PAAm from 1.35 × 10^?3 to 1.56 × 10^?2 S cm^?1. The maximum ionic conductivity of 7.0 × 10^?1 S cm^?1 was obtained with 3 M MSA at room temperature. The chemical interaction between PAAm and MSA was studied by Fourier transformed infra-red. The performance as a polymer electrolyte was evaluated from the cell discharge and open circuit potential measurements of a tin-air cell. The tin-air cell supported relatively high current, up to 12 mA cm^?2 with a maximum power density of 5 mW cm^?2. The open-circuit potential of the cell was 1.27 V for 24 h.     

Organotrisulfide: A High Capacity Cathode Material for Rechargeable Lithium Batteries

An organotrisulfide (RSSSR, R is an organic group) has three sulfur atoms which could be involved in multi‐electron reduction reactions; therefore it is a promising electrode material for batteries. Herein, we use dimethyl trisulfide (DMTS) as a model compound to study its redox reactions in rechargeable lithium batteries. With the aid of XRD, XPS, and GC‐MS analysis, we confirm DMTS could undergo almost a 4 e^? reduction process in a complete discharge to 1.0 V. The discharge products are primarily LiSCH₃ and Li₂S. The lithium cell with DMTS catholyte delivers an initial specific capacity of 720 mAh g^?1_DMTS and retains 82 % of the capacity over 50 cycles at C/10 rate. When the electrolyte/DMTS ratio is 3:1 mL g^?1, the reversible specific energy for the cell including electrolyte can be 229 Wh kg^?1. This study shows organotrisulfide is a promising high‐capacity cathode material for high‐energy rechargeable lithium batteries.     

Morphology-controllable synthesis of LiMn2O4 particles as cathode materials of lithium batteries

We reported a new method for the preparation of morphology-controllable LiMn₂O₄ particles. In this method, dimension-different MnO₂ nanowires synthesized hydrothermally by adjusting the reaction temperature were used as the precursor. The morphology and structure of the resulting products were characterized with scanning electron microscope and X-ray diffraction, and the performances of the prepared LiMn₂O₄ samples as cathode material of lithium batteries were investigated by cyclic voltammetry and galvanostatic charge/discharge test. The results indicate that the morphology of LiMn₂O₄ transforms from tridimensional particle (TP) to unidimensional rod (UR) through quadrate lamina (QL) with increasing the diameter and length of MnO₂ nanowires. Although the cyclic stabilities of LiMn₂O₄-TP, LiMn₂O₄-QL, and LiMn₂O₄-UR are very close (the 0.1 C capacity after 50 cycles is 101, 93, and 99 mAh g^?1 at 25 °C, and 84, 78, and 82 mAh g^?1 at 50 °C, respectively), LiMn₂O₄-QL delivers much higher rate capacity (about 70 mAh g^?1 at 5 C and 30 mAh g^?1 at 10 C) than LiMn₂O₄-TP and LiMn₂O₄-UR (about 20 mAh g^?1 at 5 C, 3 mAh g^?1 at 10 C, 25 mAh g^?1 at 5 C, and 3 mAh g^?1 at 10 C).     

Boron-incorporated Sulfonated polysulfone/polyphosphoric acid electrolytes for supercapacitor application

In the present work, boron-doped multicomponent gel polymer electrolytes composed of host polymer, sulfonated polysulfone (SPSU) and the additives; ionic liquid, 1-ethyl-3-methyl-imidazolium tetrafluoroborate (IL), H₃BO₃, polyphosphoric acid (PPA) were prepared. Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) techniques were used to characterize the sulfonated polysulfone-based electrolytes. Ion conductivity of these gel electrolytes were studied by dielectric impedance analyzer within the temperature from ?20 to 100°C. The ionic conductivity of the SPSU-5IL-1PPA and SPSU-5IL-1H₃BO₃-1PPA were measured as 4.8 × 10^?3 and 9 × 10^?4 S cm^?1, respectively. Supercapacitor having activated carbon-based composite electrode and electrolyte was constructed with the configuration: Al/C/electrolyte/C/Al. The electrochemical properties and ion transfer characteristics of the supercapacitor were investigated by the cyclic voltammetry (CV). Galvanostatic charge—discharge experiments exhibited good electrochemical reversibility and produced a specific capacitance value of 120 F g^?1 at 1 A g^?1. The symmetric supercapacitor system was retained almost 85% of its initial activity after 1000 cycle.