Study of carbon surface-modified Li[Li0.2Mn0.54Ni0.13Co0.13]O2 for high-capacity lithium ion battery cathode

Carbon surface-modified Li-excess layered oxide solid solution Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ cathode is fabricated through a liquid phase route using polyvinylpyrrolidone as carbon source. X-ray diffraction and X-ray photoelectron spectroscopy indicate that the crystal structure and the chemical states of elements for Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ are kept after carbon surface treatment. The high-resolution transmission electron microscopy demonstrated the existence of very little carbon on the surface and the clear boundary after carbon treatment. The carbon surface-modified sample delivers a discharge capacity of 293.2 mAh?g^?1 at C/10 rate (suppose 1 C rate?=?250 mA?g^?1) and 191.6 mAh?g^?1 at 1 C rate between 2.0 and 4.8 V; the capacity retention rate is ～86 % after 70 cycles at 1 C rate. Superior electrochemical properties can be contributed to the carbon surface modification in these aspects including minimizing nanoparticle aggregation and cell polarization, increasing the electronic conductivity, suppressing the elimination of oxide ion vacancies, as well as suppressing the formation of the thick solid electrolyte interfacial layer. Moreover, the annealing process of carbon surface modification might be able to consume Li₂CO₃ impurity partly and cause the recrystallization of the surface disordered layer.     

Mesoporous Spherical Li4Ti5O12 as High‐Performance Anodes for Lithium‐Ion Batteries

Porous microspherical Li₄Ti₅O₁₂ aggregates (LTO‐PSA) can be successfully prepared by using porous spherical TiO₂ as a titanium source and lithium acetate as a lithium source followed by calcinations. The synthesized LTO‐PSA possess outstanding morphology, with nanosized, porous, and spherical distributions, that allow good electrochemical performances, including high reversible capacity, good cycling stability, and impressive rate capacity, to be achieved. The specific capacity of the LTO‐PSA at 30 C is as high as 141 mA h g^?1, whereas that of normal Li₄Ti₅O₁₂ powders prepared by a sol–gel method can only achieve 100 mA h g^?1. This improved rate performance can be ascribed to small Li₄Ti₅O₁₂ nanocrystallites, a three‐dimensional mesoporous structure, and enhanced ionic conductivity.     

New NASICON type oxyanion high capacity anode, Li2Co2(MoO4)3, for lithium-ion batteries: preliminary studies

We describe in this paper the lithium insertion/extraction behavior of a new NASICON type Li₂Co₂(MoO₄)₃ at a low potential and explored the possibility of considering this new oxyanion material as anode for lithium-ion batteries for the first time. Li₂Co₂(MoO₄)₃ was synthesized by a soft-combustion glycine-nitrate low temperature protocol. Test cells were assembled using composite Li₂Co₂(MoO₄)₃ as the negative electrode material and a thin lithium foil as the positive electrode material separated by a microporous polypropylene (Celgard® membrane) soaked in aprotic organic electrolyte (1 M LiPF₆ in EC/DMC). Electrochemical discharge down to 0.001 V from OCV (～3.5 V) revealed that about 35 Li⁺ could ^possibly be inserted into Li₂Co₂(MoO₄)₃ during the first discharge (reduction) corresponding to a specific capacity amounting to 1,500 mAh g^?1. This is roughly fourfold higher compared to that of frequently used graphite electrodes. However, about 24 Li⁺ could be extracted during the first charge. It is interesting to note that the same amount of Li⁺ could be inserted during the second Li⁺ insertion process (second cycle discharge) giving rise to a second discharge capacity of 1,070 mAh g^?1. It was also observed that a major portion of lithium intake occurs below 1.0 V vs Li/Li⁺, which is typical of anodes being used in lithium-ion batteries.     

Biomimetic Straw-Like Bundle Cobalt-Doped Fe2O3 Electrodes towards Superior Lithium-Ion Storage

Biomimetic straw-like bundles of Co-doped Fe₂O₃ (SCF), with Co²⁺ incorporated into the lattice of α-Fe₂O₃, was fabricated through a cost-effective hydrothermal process and used as the anode material for lithium-ion batteries (LIBs). The SCF exhibited ultrahigh initial discharge specific capacity (1760.7 mA h⁻¹ g⁻¹ at 200 mA g⁻¹) and cycling stability (with the capacity retention of 1268.3 mA h⁻¹ g⁻¹ after 350 cycles at 200 mA g⁻¹). In addition, a superior rate capacity of 376.1 mA h⁻¹ g⁻¹ was obtained at a high current density of 4000 mA g⁻¹. The remarkable electrochemical lithium storage of SCF is attributed to the Co-doping, which increases the unit cell volume and affects the whole structure. It makes the Li⁺ insertion–extraction process more flexible. Meanwhile, the distinctive straw-like bundle structure can accelerate Li ion diffusion and alleviate the huge volume expansion upon cycling.     

Preparation of Li2SnO3 and its application in lithium‐ion batteries

Tin‐based oxide Li₂SnO₃ has been synthesized by a hydrothermal route as negative material for lithium‐ion batteries. The microstructure and electrochemical properties of the as‐synthesized materials were investigated by some characterizations means and electrochemical measurements. The as‐synthesized Li₂SnO₃ is a porous rod, which is composed of many uniform and regular nano‐flakes with a size of 50–60 nm. Li₂SnO₃ also displays an electrochemical performance with high capacity and good cycling stability (510.2 mAh g^?1 after 50 cycles at a current density of 60 mA g^?1 between 0.0 V and 2.0 V verusus Li/Li⁺). Copyright © 2013 John Wiley & Sons, Ltd.     

Electrochemical behavior of Li[Li0.2Co0.3Mn0.5]O2 as cathode material in Li2SO4 aqueous electrolyte

Layered, lithium-rich Li[Li_0.2Co_0.3Mn_0.5]O₂ cathode material is synthesized by reactions under autogenic pressure at elevated temperature (RAPET) method, and its electrochemical behavior is studied in 2?M Li₂SO₄ aqueous solution and compared with that in a non-aqueous electrolyte. In cyclic voltammetry (CV), Li[Li_0.2Co_0.3Mn_0.5]O₂ electrode exhibits a pair of reversible redox peaks corresponding to lithium ion intercalation and deintercalation at the safe potential window without causing the electrolysis of water. CV experiments at various scan rates revealed a linear relationship between the peak current and the square root of scan rate for all peak pairs, indicating that the lithium ion intercalation–deintercalation processes are diffusion controlled. The corresponding diffusion coefficients are found to be in the order of 10^?8?cm²?s^?1. A typical cell employing Li[Li_0.2Co_0.3Mn_0.5]O₂ as cathode and LiTi₂(PO₄)₃ as anode in 2?M Li₂SO₄ solution delivers a discharge capacity of 90?mA?h g^?1. Electrochemical impedance spectral data measured at various discharge potentials are analyzed to determine the kinetic parameters which characterize intercalation–deintercalation of lithium ions in Li[Li_0.2Co_0.3Mn_0.5]O₂ from 2?M Li₂SO₄ aqueous electrolyte.     

Graphitized carbon and graphene modified Fe2O3/Li4Ti5O12 as anode material for lithium ion batteries

Graphitized carbon (GC) and graphene (GE) modified Fe₂O₃/Li₄Ti₅O₁₂ (LTO) composites have been synthesized via a solid‐state reaction, respectively. The structure, morphology and electrochemical performance of the materials have also been characterized with X‐ray diffraction (XRD), scanning electron microscope (SEM) with an energy dispersive spectroscopy (EDS) system, X‐ray photoelectron spectrometer (XPS), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. The discharge capacities of Fe₂O₃/LTO, GC/Fe₂O₃/LTO and GE/Fe₂O₃/LTO are 100.2 mAh g^?1, 207.5 mAh g^?1 and 238.9 mAh g^?1 after 100 cycles at the current density of 176 mA g^?1. The cyclic stability and rate capability are in the order of GE/Fe₂O₃/LTO > GC/Fe₂O₃/LTO > Fe₂O₃/LTO because of the synergistic effect between GC (GE) and Fe₂O₃/LTO. Copyright © 2016 John Wiley & Sons, Ltd.     

Lithium garnet based free-standing solid polymer composite membrane for rechargeable lithium battery

Electrolytes with high lithium-ion conductivity, better mechanical strength and large electrochemical window are essential for the realization of high-energy density lithium batteries. Polymer electrolytes are gaining interest due to their inherent flexibility and nonflammability over conventional liquid electrolytes. In this work, lithium garnet composite polymer electrolyte membrane (GCPEM) consisting of large molecular weight (W_avg ~?5?×?10⁶) polyethylene oxide (PEO) complexed with lithium perchlorate (LiClO₄) and lithium garnet oxide Li_6.28Al_0.24La₃Zr₂O₁₂ (Al-LLZO) is prepared by solution-casting method. Significant improvement in Li⁺ conductivity for Al-LLZO containing GCPEM is observed compared with the Al-LLZO free polymer membrane. Maximized room temperature (30 °C) Li⁺ conductivity of 4.40?×?10^?4 S cm^?1 and wide electrochemical window (4.5 V) is observed for PEO₈/LiClO₄?+?20 wt% Al-LLZO (GCPEM-20) membrane. The fabricated cell with LiCoO₂ as cathode, metallic lithium as anode and GCPEM-20 as electrolyte membrane delivers an initial charge/discharge capacity of 146 mAh g^?1/142 mAh g^?1 at 25 °C with 0.06 C-rate.     

Electrospun Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite nanofibers for enhanced high-rate lithium ion batteries

Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers with the mean diameter of ca. 60 nm have been synthesized via facile electrospinning. When the molar ratio of Li to Ti is 4.8:5, the Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers exhibit initial discharge capacity of 216.07 mAh g^?1 at 0.1 C, rate capability of 151 mAh g^?1 after being cycled at 20 C, and cycling stability of 122.93 mAh g^?1 after 1000 cycles at 20 C. Compared with pure Li₄Ti₅O₁₂ nanofibers and Li₂TiO₃ nanofibers, Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers show better performance when used as anode materials for lithium ion batteries. The enhanced electrochemical performances are explained by the incorporation of appropriate Li₂TiO₃ which could strengthen the structure stability of the hosted materials and has fast Li⁺-conductor characteristics, and the nanostructure of nanofibers which could offer high specific area between the active materials and electrolyte and shorten diffusion paths for ionic transport and electronic conduction. Our new findings provide an effective synthetic way to produce high-performance Li₄Ti₅O₁₂ anodes for lithium rechargeable batteries.     

Preparation of Li4Ti5O12 Yolk–Shell Powders by Spray Pyrolysis and their Electrochemical Properties

We have reported for the first time the preparation of yolk–shell‐structured Li₄Ti₅O₁₂ powders for use as anode materials in lithium‐ion batteries. One Li₄Ti₅O₁₂ yolk–shell‐particle powder is directly formed from each droplet containing lithium, titanium, and carbon components inside the hot wall reactor maintained at 900 °C. The precursor Li₄Ti₅O₁₂ yolk–shell‐particle powders, which are directly prepared by spray pyrolysis, have initial discharge and charge capacities of 155 and 122 mA h g^?1, respectively, at a current density of 175 mA g^?1. Post‐treatment of the yolk–shell‐particle powders at temperatures of 700 and 800 °C improves the initial discharge and charge capacities. The initial discharge capacities of the Li₄Ti₅O₁₂ powders with a yolk–shell structure and a dense structure post‐treated at 800 °C are 189 and 168 mA h g^?1, respectively. After 100 cycles, the corresponding capacities are 172 and 152 mA h g^?1, respectively (retentions of 91 and 90 %).     

Nitridated mesoporous Li4Ti5O12 spheres for high-rate lithium-ion batteries anode material

Nitridated mesoporous Li₄Ti₅O₁₂ spheres were synthesized by a simple ammonia treatment of Li₄Ti₅O₁₂ derived from mesoporous TiO₂ particles and lithium acetate dihydrate via a solid state reaction in the presence of polyethylene glycol 20000. The carbonization of polyethylene glycol could effectively restrict the growth of primary particles, which was favorable for lithium ions diffusing into the nanosized TiO₂ lattice during the solid state reaction to form a pure phase Li₄Ti₅O₁₂. After a subsequent thermal nitridation treatment, a high conductive thin TiO _x N _y layer was in situ constructed on the surface of the primary nanoparticles. As a result, the nitridated mesoporous Li₄Ti₅O₁₂ structure, possessing shorter lithium-ion diffusion path and better electrical conductivity, displays significantly improved rate capability. The discharge capacity reaches 138 mAh?g^?1 at 10 C rate and 120 mAh?g^?1 at 20 C rate in the voltage range of 1–3 V.     

Sucrose assisted hydrothermal synthesis of SnO2/graphene nanocomposites with improved lithium storage properties

SnO₂/graphene nanocomposites are synthesized by a new hydrothermal treatment strategy under the assistance of sucrose. From the images of the scanning electron microscope (SEM) and transmission electron microscope (TEM), it can be observed that SnO₂ nanoparticles with the size of 4~5 nm uniformly distribute on the graphene nanosheets. The result demonstrates that sucrose can effectively prevent graphene nanosheets from restacking during hydrothermal treatment and subsequently treatment. The charging/discharging test result indicates that the SnO₂/graphene nanocomposites exhibit high specific capacity and excellent cycleability. The first reversible specific capacity is 729 mAh.g^?1 at the current density of 50 mA.g^?1, and remains 646 mAh.g^?1 after 30 cycles at the current density of 100 mA.g^?1, 30 cycles at the current density of 200 mA.g^?1, 30 cycles at the current density of 400 mA.g^?1, 30 cycles at the current density of 800 mA.g^?1, and 30 cycles at the current density of 50 mA.g^?1.     

Natural graphite enhanced the electrochemical performance of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> cathode material for lithium ion batteries

Natural graphite treated by mechanical activation can be directly applied to the preparation of Li₃V₂(PO₄)₃. The carbon-coated Li₃V₂(PO₄)₃ with monoclinic structure was successfully synthesized by using natural graphite as carbon source and reducing agent. The amount of activated graphite is optimized by X-ray diffraction, scanning electron microscope, transmission electron microscope, Raman spectrum, galvanostatic charge/discharge measurements, cyclic voltammetry, and electrochemical impedance spectroscopy tests. Our results show that Li₃V₂(PO₄)₃ (LVP)-10G exhibits the highest initial discharge capacity of 189 mAh g^?1 at 0.1 C and 162.9 mAh g^?1 at 1 C in the voltage range of 3.0–4.8 V. Therefore, natural graphite is a promising carbon source for LVP cathode material in lithium ion batteries.     

Ionic conductivity and interfacial stability of Li6PS5Cl–Li6.5La3Zr1.5Ta0.5O12 composite electrolyte

Solid electrolytes which possess excellent lithium-ion conductivity and chemical compatibility with electrode materials are necessary for the commercialization of all-solid-state lithium batteries. However, a single solid electrolyte meeting above requirements is difficult. Consequently, the composite electrolytes have attracted more attention. In this paper, Li₆PS₅Cl–xLi_6.5La₃Zr_1.5Ta_0.5O₁₂ (LLZTO) (x = 0, 2.5 wt%, 5 wt%, 10 wt%) composite electrolytes are prepared by a simple planetary grinding process. It has been found that adding an appropriate amount of LLZTO can increase the lithium-ion conductivity. At 30 °C, the lithium-ion conductivity increases from 2.6 × 10⁻⁴ S/cm (Li₆PS₅Cl) to 5.4 × 10⁻⁴ S/cm (Li₆PS₅Cl-5 wt% LLZTO). Besides, the addition of LLZTO to the Li₆PS₅Cl can influence the growth rate of the SEI. It has been shown that the SEI growth rate obeys a parabolic rate law, and the growth rates of Li₆PS₅Cl, Li₆PS₅Cl-2.5 wt% LLZTO, Li₆PS₅Cl-5 wt% LLZTO, and Li₆PS₅Cl-10 wt% LLZTO are 8.62, 3.53, 3.33, and 3.38 Ω/h^1/2 at 60 °C, respectively. In lithium plating and stripping experiment, the voltage of symmetrical Li/Li₆PS₅Cl/Li cell suddenly drops to 0 V after cycling 39 h at 0.103 mA/cm² (0.097 mAh/cm²). On the contrary, the Li/Li₆PS₅Cl–xLLZTO (x = 2.5 wt%, 5 wt%, 10 wt%)/Li symmetrical cell exhibits a stable voltage profile over 100 h at the same test conditions. The corresponding interfacial impedance of Li/Li₆PS₅Cl–xLLZTO (x = 2.5 wt%, 5 wt%, 10 wt%) remains stable after 10, 30, and 50 charge/discharge cycles.

     

Green and efficient extraction strategy to lithium isotope separation with double ionic liquids as the medium and ionic associated agent

The paper reported a green and efficient extraction strategy to lithium isotope separation. A 4-methyl-10-hydroxybenzoquinoline (ROH), hydrophobic ionic liquid—1,3-di(isooctyl)imidazolium hexafluorophosphate ([D(i-C₈)IM][PF₆]), and hydrophilic ionic liquid—1-butyl-3-methylimidazolium chloride (ILCl) were used as the chelating agent, extraction medium and ionic associated agent. Lithium ion (Li⁺) first reacted with ROH in strong alkali solution to produce a lithium complex anion. It then associated with IL⁺ to form the Li(RO)₂IL complex, which was rapidly extracted into the organic phase. Factors for effect on the lithium isotope separation were examined. To obtain high extraction efficiency, a saturated ROH in the [D(i-C₈)IM][PF₆] (0.3 mol l^?1), mixed aqueous solution containing 0.3 mol l^?1 lithium chloride, 1.6 mol l^?1 sodium hydroxide and 0.8 mol l^?1 ILCl and 3:1 were selected as the organic phase, aqueous phase and phase ratio (o/a). Under optimized conditions, the single-stage extraction efficiency was found to be 52 %. The saturated lithium concentration in the organic phase was up to 0.15 mol l^?1. The free energy change (ΔG), enthalpy change (ΔH) and entropy change (ΔS) of the extraction process were ?0.097 J mol^?1, ?14.70 J mol K^?1 and ?48.17 J mol^?1 K^?1, indicating a exothermic process. The partition coefficients of lithium will enhance with decrease of the temperature. Thus, a 25 °C of operating temperature was employed for total lithium isotope separation process. Lithium in Li(RO)₂IL was stripped by the sodium chloride of 5 mol l^?1 with a phase ratio (o/a) of 4. The lithium isotope exchange reaction in the interface between organic phase and aqueous phase reached the equilibrium within 1 min. The single-stage isotope separation factor of ⁷Li–⁶Li was up to 1.023 ± 0.002, indicating that ⁷Li was concentrated in organic phase and ⁶Li was concentrated in aqueous phase. All chemical reagents used can be well recycled. The extraction strategy offers green nature, low product cost, high efficiency and good application prospect to lithium isotope separation.     

Synthesis of Mesoporous Lithium Titanate Thin Films and Monoliths as an Anode Material for High‐Rate Lithium‐Ion Batteries

Mesoporous Li₄Ti₅O₁₂ (LTO) thin film is an important anode material for lithium‐ion batteries (LIBs). Mesoporous films could be prepared by self‐assembly processes. A molten‐salt‐assisted self‐assembly (MASA) process is used to prepare mesoporous thin films of LTOs. Clear solutions of CTAB, P123, LiNO₃, HNO₃, and Ti(OC₄H₉)₄ in ethanol form gel‐like meso‐ordered films upon either spin or spray coating. In the assembly process, the CTAB/P123 molar ratio of 14 is required to accommodate enough salt species in the mesophase, in which the Li^I/P123 ratio can be varied between molar ratios of 28 and 72. Calcination of the meso‐ordered films produces transparent mesoporous spinel LTO films that are abbreviated as Cxx‐yyy‐zzz or CAxx‐yyy‐zzz (C=calcined, CA=calcined–annealed, xx=Li^I/P123 molar ratio, and yyy=calcination and zzz=annealing temperatures in Celsius) herein. All samples were characterized by using XRD, TEM, N₂‐sorption, and Raman techniques and it was found that, at all compositions, the LTO spinel phase formed with or without an anatase phase as an impurity. Electrochemical characterization of the films shows excellent performance at different current rates. The CA40‐350‐450 sample performs best among all samples tested, yielding an average discharge capacity of (176±1) mA h g^?1 at C/2 and (139±4) mA h g^?1 at 50 C and keeping 92 % of its initial discharge capacity upon 50 cycles at C/2.     

Iron Fluoride Hollow Porous Microspheres: Facile Solution‐Phase Synthesis and Their Application for Li‐Ion Battery Cathodes

Iron fluoride cathodes have been attracting considerable interest due to their high electromotive force value of 2.7 V and their high theoretical capacity of 237 mA h g^?1 (1 e^? transfer). In this study, uniform iron fluoride hollow porous microspheres have been synthesized for the first time by using a facile and scalable solution‐phase route. These uniform porous and hollow microspheres show a high specific capacity of 210 mA h g^?1 at 0.1 C, and excellent rate capability (100 mA h g^?1 at 1 C) between 1.7 and 4.5 V versus Li/Li⁺. When in the range of 1.3 to 4.5 V, stable capacity was achieved at 350 mA h g^?1 at a current of 50 mA g^?1.     

Enhanced lithium-ion intercalation and conduction of transparent tantalum oxide films by lithium addition with an atmospheric pressure plasma jet

An investigation is conducted on enhancing lithium-ion intercalation and conduction performance of transparent organo tantalum oxide (TaO _y C _z ) films, by addition of lithium via a fast co-synthesis onto 40 Ω/□ flexible polyethylene terephthalate/indium tin oxide substrates at the short exposed durations of 33–34 s, using an atmospheric pressure plasma jet (APPJ) at various mixed concentrations of tantalum ethoxide [Ta(OC₂H₅)₅] and lithium tert-butoxide [(CH₃)₃COLi] precursors. Transparent organo-lithiated tantalum oxide (Li _x TaO _y C _z ) films expose noteworthy Li⁺ ion intercalation and conduction performance for 200 cycles of reversible Li⁺ ion intercalation and deintercalation in a 1 M LiClO₄-propylene carbonate electrolyte, by switching measurements with a potential sweep from ?1.25 to 1.25 V at a scan rate of 50 mV/s and a potential step at ?1.25 and 1.25 V, even after being bent 360° around a 2.5-cm diameter rod for 1000 cycles. The Li⁺ ionic diffusion coefficient and conductivity of 6.2?×?10^?10 cm²/s and 6.0?×?10^?11 S/cm for TaO _y C _z films are greatly progressed of up to 9.6?×?10^?10 cm²/s and 7.8?×?10^?9 S/cm for Li _x TaO _y C _z films by co-synthesis with an APPJ.     

Tin oxide-titanium oxide/graphene composited as anode materials for lithium-ion batteries

A tin oxide-titanium oxide/graphene (SnO₂-TiO₂/G) ternary nanocomposite as high-performance anode for Li-ion batteries was prepared via a simple reflux method. The graphite oxide (GO) was reduced to graphene nanosheet, and the SnO₂-TiO₂ nanocomposites were evenly distributed on the graphene matrix in the SnO₂-TiO₂/G nanocomposite. The as-prepared SnO₂-TiO₂/G nanocomposites were employed as anode materials for lithium-ion batteries, showing an outstanding performance with high reversible capacity and long cycle life. The composite delivered a superior initial discharge capacity of 1,594.6 mAh g^?1 and a reversible specific capacity of 1,500.3 mAh g^?1 at a current density of 100 mA g^?1. After 100 cycles, the reversible discharge capacity was still maintained at 1,177.4 mAh g^?1 at a current density of 100 mA g^?1 with a high retained rate of reversible capacity of 73.8 %. The addition of small amount of TiO₂ nanoparticles improved the cycling stability and specific capacity of SnO₂-TiO₂/G nanocomposite, obviously. The results demonstrate that the SnO₂-TiO₂/G nanocomposite is a promising alternative anode material for practical Li-ion batteries.     

Storage performance of LiFe<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>PO<Subscript>4</Subscript> nanoplates (<Emphasis Type="Italic">x </Emphasis>= 0, 0.5, and 1)

Although LiFePO₄ (LFP) is considered to be a potential cathode material for the lithium-ion batteries, its rate performance is significantly restricted by sluggish kinetics of electrons and lithium ions. Several attempts have been made so far to improve the performance of LiFePO₄ by reducing the grain size, doping with aliovalent atoms, and coating conductive materials such as carbon or RuO₂. We report here synthesis of LFP nanoplates by solvothermal method, tailoring the thickness as well as carbon coverage at surfaces to explore their influence on the storage performance. Due to the fact that Li⁺ ion diffuses along the b-axis, solvothermal method was aimed to control the thickness of nanoplates across the b-axis. We synthesized several nanoplates with various plate thicknesses along b-axis; among those, nanoplates of LFP with ～30-nm-thick b-axis having thin (2–5 nm) and uniform layer of carbon coating exhibits high storage capacity as well as high rate performances. Thus, a favorable morphology for LiFePO₄ has been achieved via solvothermal method for fast insertion/extraction of Li⁺ as compared to spherical nanoparticles of carbon-coated LFP. Galvanostatic cycling shows a capacity of 164?±?5 mAh g^?1 at 0.1 C rate, 100?±?5 mAh g^?1 at 10 C rate, and 46?±?5 mAh g^?1 at 30 C rate, with excellent capacity retention of up to 50 cycles. Further attempts have been made to synthesize LiMnPO₄ (LMP) as well as Li(Fe_1???x Mn _x )PO₄/C (x?=?0.5) nanoplates using solvothermal method. Although LiMnPO₄ does not exhibit high storage behavior comparable with that of LiFePO₄, the mixed systems have shown an impressive storage performance.