SiO2 的甲硅烷基化对钴基催化剂费-托合成催化性能的影响

利用甲硅烷基化作用制得了不同疏水程度的SiO₂载体,采用等体积浸渍法制备了质量分数为5%的一系列负载型钴催化剂。结合FT-IR、²⁹Si CP MAS NMR、BET、XRD、Raman、XPS和H₂-TPR等表征手段,考察了SiO₂甲硅烷基化对钴基催化剂物相结构、还原行为以及费-托合成催化性能的影响。催化剂在固定床反应器中,在p=2.0 MPa、t=240 ℃、n(H₂)/n(CO)=2和GHSV=1 000 h^-1的条件下进行评价。结果表明,随 SiO₂ 疏水程度的增加,钴催化剂的Co₃O₄晶粒长大且晶型趋于完整,钴硅相互作用减弱,还原度增加,催化剂的活性增强。     

有机改性二氧化硅及其负载钴催化剂的费托合成反应性能

利用硅烷化作用分别制得了甲基、二甲基和三甲基改性的SiO2载体,采用等体积浸渍法制备了质量分数为5%的一系列负载型钴催化剂.考察了有机改性对催化剂费托合成催化性能的影响.结果表明,SiO2经有机基团改性后,表面硅羟基浓度减小,削弱了钴硅之间的相互作用,促进了催化剂的还原,提高了催化剂的活性,降低了甲烷选择性.由于空间位阻不同,不同有机基团改性的SiO2的表面硅羟基浓度不同,催化剂活性随着表面硅羟基浓度的减小而提高.     

结构助剂SiO2、Al2O3对铁基催化剂浆态床F-T合成性能的影响

采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了微球状Fe/Cu/K/SiO2和Fe/Cu/K/Al2O3催化剂,研究SiO2和Al2O3作为结构助剂对铁基催化剂吸附行为、炭化行为及F-T合成反应性能的影响。表征结果表明,与Al2O3相比较,SiO2抑制了H2的吸附,但促进了CO的吸附,有利于催化剂的炭化。催化剂在260℃、1.5MPa、H2/CO=0.67和2000h-1下的浆态床F-T合成反应评价表明,Fe/Cu/K/SiO2催化剂具有较高的F-T合成活性、高的水煤气变换反应（WGS）活性,且其烃产物选择性明显向高炭数方向偏移,而Fe/Cu/K/Al2O3催化剂则表现出较低的F-T合成活性、低的水煤气变换反应（WGS）活性和高的轻质烃选择性。但Fe/Cu/K/Al2O3催化剂比Fe/Cu/K/SiO2催化剂具有更好的运行稳定性。     

超声浸渍对费托合成Co/Zr/SiO2催化剂性能的影响

采用超声浸渍法制备了费托合成Co/Zr/SiO2催化剂,考察了超声波功率对催化剂费托反应性能的影响,并运用N2物理吸附、X射线衍射、H2程序升温脱附、H2程序升温还原和透射电子显微镜对催化剂进行了表征,结果表明,超声波处理可以增大催化剂的比表面积,减小金属Co的粒径,并使其较为均匀地分散于载体表面,其中以高功率超声波作...     

完全液相法制备的Cu-Zn-Si-Al浆状催化剂一步法合成二甲醚的失活研究

采用完全液相法制备了Cu-Zn-Si-Al浆状二甲醚合成催化剂, 分析研究了其在浆态床合成气一步法合成二甲醚过程中的失活现象和机理. 采用X射线粉末衍射、 N_2吸附测试、 X射线光电子能谱以及元素分析等表征方法对催化剂使用前后的变化情况进行了分析. 结果表明, 完全液相法制备的Cu-Zn-Si-Al浆状催化剂的失活与传统方法制备的催化剂不尽相同, 没有发现催化剂Cu晶粒的长大和比表面积降低等失活因素;催化剂失活与Si的存在有关, Cu组分的流失是其失活的主要原因.     

In situ surface oxidation study of a planar Co/SiO2/Si(100) model catalyst with nanosized cobalt crystallites under model Fischer-Tropsch synthesis conditions

The oxidation of nanosized metallic cobalt to cobalt oxide during Fischer-Tropsch synthesis (FTS) has long been postulated as a major deactivation mechanism. In this study a planar Co/SiO(2)/Si(100) model catalyst with well-defined cobalt crystallites, close to the threshold value reported for oxidation in the literature (4-10 nm), was prepared by the spin coating method. The planar Co/SiO(2)/Si(100) model catalyst was characterized with atomic force microscopy, X-ray photoelectron spectroscopy, and Rutherford backscattering. The surface oxidation behavior of the nanosized metallic cobalt crystallites of 4-5 nm was studied using in situ near-edge X-ray absorption fine structure under model FTS conditions, i.e., H(2)/H(2)O = 1, P(Total) = 0.4 mbar, and 150-450 degrees C. No surface oxidation of metallic cobalt was observed under these model FTS conditions over a wide temperature range, i.e., 150-400 degrees C.     

完全液相法与溶胶-凝胶法制备Cu-Zn-Al双功能催化剂对浆态床一步法合成二甲醚的催化性能比较

采用完全液相法和溶胶-凝胶法分别制备了组成完全相同的Cu-Zn-Al双功能催化剂,用XRD、氮气吸附-脱附实验和XPS等手段对催化剂的性质进行表征,考察了催化剂对浆态床一步法合成二甲醚反应的催化性能.结果表明,两种方法制备的Cu基催化剂中Cu组分的物相和表面Cu含量明显不同,而催化剂的织构性质基本相同.完全液相法制备的...     

Deactivation studies of nano-structured iron catalyst in Fischer-Tropsch synthesis

A nano-structured iron catalyst for syngas conversion to hydrocarbons in Fischer-Tropsch synthesis (FTS) was prepared by micro-emulsion method. Compositions of bulk iron phase and phase transformations of carbonaceous species during catalyst deactivation in FTS reaction were characterized by temperature-programmed surface reaction with hydrogen (TPSR-H2), and XRD techniques. Many carbonaceous species on surface and bulk of the nano-structured iron catalysts were completely identified by combined TPSR-H2 and XRD spectra and which were compared with those recorded on conventional co-precipitated iron catalyst. The results reveal that the catalyst deactivation results from the formation of inactive carbide phases and surface carbonaceous species like graphite, and it will be increased when the particle size of iron oxides was reduced in FTS iron catalyst.     

焙烧温度对含Mg助剂的铁基催化剂F-T合成反应性能的影响

采用连续共沉淀和喷雾干燥技术相结合的方法制备了Mg助剂的Fe/Cu/K/SiO2催化剂,采用N2物理吸附、XRD、MES 和H2-TPR等表征手段,考察了焙烧温度对催化剂比表面积、体相结构和还原性能的影响。结果表明,随着焙烧温度的升高,催化剂的比表面积降低,平均孔径增大,体相中α-Fe2O3晶粒逐渐增大,催化剂变的越来越难还原,其结构更加稳定。在H2/CO （摩尔比）= 2.2、250 ℃、2.0 MPa和2 000 h－1于固定床反应器考察了焙烧温度对该催化剂F-T合成反应性能的影响,结果表明,随着焙烧温度的升高,催化剂的F-T合成反应活性降低,在运行过程中反应活性逐渐增加直至达到平稳,但达到平稳所需的诱导期越来越长;提高焙烧温度使烃产物分布向重质烃方向转移,有利于降低CH4的选择性,促进重质烃的生成。     

Effect of Re and Al 2 O 3 Promotion on the Working Stability of Cobalt Catalysts for the Fischer–Tropsch Synthesis

The results of the working stability studies of cobalt catalysts based on SiO2 and Al2O3 promoted with Re and Al2O3 in the synthesis of hydrocarbons from CO and H2 in continuous tests for 200–300 h are presented. The prepared catalysts were characterized by transmission electron spectroscopy, temperature-programmed reduction with hydrogen, temperature-programmed desorption of CO, and X-ray fluorescence spectroscopy and tested at a temperature 200°C, a pressure of 0.1 MPa, and a GHSV of 100 h–1. It was determined that a cobalt–silica catalyst promoted with Al2O3 had the highest activity. It was established that the addition of Al2O3 to a cobalt–silica catalyst increased the conversion of CO and selectivity for C5+ hydrocarbons and inhibited the agglomeration of Co particles under the action of a reaction atmosphere in the Fischer–Tropsch synthesis. It was found that the initial conversion of CO increased by a factor of 2 upon the introduction of 0.1 wt % rhenium into the Co/γ-Al2O3 catalyst; however, the rate of its deactivation increased in this case due to an almost twofold increase in the size of cobalt particles in the course of synthesis after operation for 300 h.     

硅对铁基费-托合成催化剂的影响

用共沉淀法制备了一系列不同硅含量的铁基催化剂,采用N2吸附和原位X射线衍射对催化剂进行了表征,在固定床反应器中考察了催化剂的费-托合成反应活性、选择性和稳定性.结果表明,含硅的催化剂具有较大的比表面积和较小的平均孔径,在CO还原及费-托合成反应中生成的碳化铁物种的稳定性比不含硅的催化剂高.在费-托合成反应中,不含硅的催化剂具有较高的初始活性,但易失活;含硅的催化剂具有较低的初始活性,但稳定性较高.Fe7C3是活性最高的碳化铁物种.随着硅含量的增加,催化剂的费-托合成反应更易生成低碳数产物.     

FeMn、FeMnNa和FeMnK催化剂上合成气制低碳烯烃的比较(英文)

研究了钠、钾助剂对FeMn合成低碳烯烃催化剂结构及性能的影响.低温N2吸附、X射线光电子能谱(XPS)、X射线衍射(XRD)、H2程序升温还原(H2-TPR)、CO/CO2程序升温脱附(CO/CO2-TPD)、M?ssbauer谱和CO+H2反应的研究结果表明,增加Mn助剂含量促进了活性相的分散和低碳烯烃的生成,而过多锰助剂在催化剂表面的富集则降低了费托合成反应的CO转化率;钾助剂和钠助剂的加入均抑制了催化剂的还原并且促进了CO2和CO的吸附.比较还原后(H2/CO摩尔比为20)和反应后(H2/CO摩尔比为3.5)催化剂的体相结构可以发现,在FeMn、FeMnNa和FeMnK催化剂中,由于钾助剂的碱性和CO吸附能力较强,因此体相中FeCx的含量相对较高;而活性测试结果表明,FeMnNa催化剂拥有最好的CO转化率(96.2%)和低碳烯烃选择性(30.5%,摩尔分数).     

间苯二酚-甲醛树脂凝胶对Co/SiO_2催化剂费-托性能的影响(英文)

采用共沉淀法制备了高Co含量的Co/SiO2费托合成催化剂,并向其中添加一定含量的间苯二酚-甲醛树脂凝胶.结果表明,催化剂在393K干燥时,树脂会发生分解,因而仅有少量的含碳凝胶残留在催化剂中.然而,少量碳凝胶的存在显著增加了催化剂的还原度和金属钴的分散度,致使催化剂表面产生更多的活性金属Co,同时,催化剂的孔径也有所增大,因此Co/SiO2催化剂具有更高的反应活性及高碳烃选择性.其中80%Co/SiO2-C催化剂活性及高碳烃的选择性与我们前期报道的一种高活性的80%Co-8%ZrO/SiO催化剂相近.     

Cr 助剂对 Fe 基催化剂结构和费托合成性能的影响

 采用 N2 吸附-脱附、X 射线衍射、穆斯堡尔谱、X 射线光电子能谱、程序升温还原和热重分析等技术研究了助剂 Cr 含量对 Fe 基费托合成催化剂的织构性质、还原行为以及物相变化的影响. 在 H2/CO = 2.0, 260~300 oC, 1.5 MPa 和 2 000 ml/(g•h) 条件下, 在固定床反应器中考察了 Cr 含量对 Fe 基催化剂费托合成反应活性和产物烃选择性的影响. 结果表明, 在氧化态催化剂中, Cr 助剂与 Fe 物相存在较强的相互作用, 形成固溶体相 α-(Cr1-xFex)2O3; 随着 Cr 含量的增加, 逐渐由单一的富 Fe 相 α-(Fe1-xCrx)2O3 向富 Fe 相和富 Cr 相 α-(Cr1-yFey)2O3 两相过渡. Fe-Cr 固溶体的生成显著抑制了催化剂的还原, 导致催化剂还原度降低, 因而催化剂活性下降. 同时, Cr 的添加提高了甲烷和轻质烃选择性, 但抑制了水煤气变换活性.     

不同pH值制备的TiO2和TiO2/SiO2催化剂结构、表面性质及光催化活性

以TiOSO₄和SiO₂溶胶为原料, 采用沉淀法用氨水调节pH值制备TiO₂和TiO₂/SiO₂催化剂. 制备的催化剂用X射线衍射(XRD), 扫描电镜(SEM), N₂吸附(BET), 紫外-可见(UV-Vis)漫反射光谱, 程序升温脱附(NH₃-TPD), 傅里叶变换红外(FT-IR)光谱技术分析. XRD谱图显示纯TiO₂中锐钛型和金红石相共存, 且金红石相含量随pH值升高而增加. 但是, TiO₂/SiO₂催化剂只有锐钛型. 扫描电镜发现制备的催化剂呈类球形, 颗粒间相互交叠, 粒径在10-25 nm之间. TiO₂和TiO₂/SiO₂光催化剂的比表面积随pH值升高略有增大. SiO₂的添加会增大催化剂的比表面积. 程序升温脱附实验结果说明催化剂的表面酸量随pH值升高而增加. TiO₂/SiO₂的表面酸量比相同pH值制备的TiO₂大. 红外光谱分析说明Si掺杂和高pH值有利于催化剂表面生成更多的羟基. TiO₂和TiO₂/SiO₂光催化剂的催化活性随pH值升高而明显增强. TiO₂/SiO₂的光催化活性优于TiO₂. TiO₂/SiO₂催化剂具有较好的耐久性.     

负载型氧化锆催化剂上甲醇脱氢制甲醛

甲醇在无氧条件下脱氢,可以制得含水量极低的甲醛。在上述反应中,主要采用以硅胶为载体的负载型氧化物催化剂,其中以周期表ⅠB和ⅡB族金属,如铜、银或锌为主要组分。这些金属的氧化物在高温下易还原、烧结和表面积炭而使催化剂失活。添加P,S,Se或Te等组分作为助催化剂,在一定程度上可以改善催化性能。最近的发展倾向是采用非负载的碱金属盐作为催化剂,如Na_2CO_3,Na_2MoO_4,或Na_xLi_(1-x)AlO_2(0≤x≤1)。这类催化剂要求过高的反应温度,如高于650℃,甚至900℃条件下使用。     

超临界条件下CO2和丙烯直接合成甲基丙烯酸Ni2(OCH3)2/SiO2催化剂

超临界反应;负载型催化剂;双核桥联配合物;配合物;超临界条件下CO2和丙烯直接合成甲基丙烯酸Ni2(OCH3)2/SiO2催化剂     

Ni-B/SiO2非晶态催化剂应用于硝基苯液相加氢制苯胺

 考察了Ni－B／SiO2非晶态催化剂在高压液相硝基苯加氢制苯胺反应中的催化活性和选择性．研究表明,该催化剂不仅具有很高的催化活性,而且对苯胺的选择性较高,优于RaneyNi以及其它Ni基催化剂．晶化导致催化剂失活．载体的存在不仅能提高催化剂的分散度,而且能对非晶态结构起稳定化作用;将催化剂保存在乙醇中可保持其活性不变．结合催化剂的表征,讨论了Ni－B／SiO2非晶态催化剂的催化性能与其结构的关系．     

Highly active and reusable catalyst for fries rearrangement of phenyl acetate

Silica-12-tungstophosphoric acid core-shell nanoparticles were prepared by sol-gel method followed by steaming. The catalytic activity of fresh and steamed catalysts was studied in Fries rearrangement of phenyl acetate. The reaction parameters, such as catalyst loading and reaction temperature, were optimized. The structural properties of the prepared catalysts were analyzed by X-ray diffraction and transmission electron microscopy techniques. The nature and strength of acid sites in the catalysts were analyzed by pyridine adsorption followed by infrared spectroscopy and differential scanning calorimetry measurements. The XRD and TEM analyses confirm the formation of silica-12-tungstophosphoric acid core-shell nanoparticles during steaming process. Acidity measurement indicates that both fresh and steamed catalyst samples carry weak acid sites and Brøsted acid sites. In addition, the steaming of heteropoly acid contained silica enhances the strength of Brøsted acid sites. The catalytic activity of fresh as well as steamed catalysts in liquid-phase Fries rearrangement showed that the steam treated sample exhibits higher conversion and selectivity to the desired product compared to the fresh catalyst sample. The higher activity of steam treated catalysts has been explained in terms of surface acidity of the catalysts. Reusability of the steamed catalyst shows that there is no appreciable change either in the conversion rate or product selectivity.     

S掺杂S-TiO_2/SiO_2可见光响应光催化剂的制备及性能

以四氯化钛为钛源,硫脲为硫源,采用液相水解-沉淀法制备了S掺杂的TiO2/SiO2(S-TiO2/SiO2)催化剂,并以苯酚为模型物,考察了催化剂在可见光区、紫外光区和太阳光下的光催化活性,以及催化剂的使用寿命和分离性能.采用X射线光电子能谱、傅里叶变换红外光谱、紫外-可见漫反射光谱、X射线衍射、透射电镜及N2吸附-脱附等技术对催化剂进行了表征.结果表明,S以+6价形式进入TiO2体相并置换晶格中的Ti4+,适量S掺杂的S-TiO2/SiO2在紫外光区、可见光区和太阳光下均表现出较高的光催化活性.SiO2与TiO2界面间有Ti-O-Si键形成,结合牢固.S掺杂在TiO2表面生成Ti-O-S键,形成新的能级结构,使光催化剂在450～550nm产生吸收,诱发TiO2可见光催化活性;同时提高了TiO2表面羟基数量.SiO2的加入可减小TiO2颗粒的平均尺寸,增大催化剂的比表面积,改善催化剂的分离性能,提高催化剂的使用寿命.