原子吸收光谱法测定三醋酸纤维素膜中铜铁

运用空气-乙炔火焰原子吸收光谱法同时测定银锌电池三醋酸纤维素膜中铜铁含量，并对测定条件和干扰因素进行了综合分析．该测定方法具有很好的灵敏度，干扰少，选择性和重现性好等优点．测定样品铜铁含量的相对标准偏差均小于1．0％．标准加入回收率均在97．3％-98．8％范围内．完全适用于银锌电池三醋酸纤维素膜中铜铁含量的控制和样品系统分析．     

电镀液中铜、铁、铅和锌等杂质元素的原子吸收光谱测定

电镀液中常见的有害杂质:铜、铁、铅和锌等的允许含量随镀液种类和杂质元素不同而异。例如,镀镍液中的铜、铁、铅和锌的允许范围在几个至几十个毫克/升内,而镀铬液中的铁的允许范围却在1—几克/升内。1964年Whittington报告用原子吸收加入法测镀镍液中的铜、铁、铅和锌。我们也用过此法。此法比较麻烦。虽然Parker报告把电镀液稀释后直接用原子吸收法测锌、铜、铬,但未报导具体条件。本文除测定镀镍液和镀钻液中低含量铁仍用加入法外,铜、铅、锌及镍、钴镀液中高于50毫克/升铁都用稀释法。实验表明:     

用N2O-C2H2原子吸收光谱法测定铜银合金中铁

提出用N2O-C2H2火焰原子吸收光谱法测试镉镍电池材料铜银合金中铁含量．方法具有良好的灵敏度,干扰少,重现性好．铁含量在0．1～30．0mg／L范围内与吸收值呈良好的线性关系．在测试铁含量为6．26mg／L（测定次数n=10）时,其相对标准偏差小于1．0％．标准回收率在97．0%-99．0％（n=6）范围内,适用于镉镍电池材料铜银合金中铁含量的质量控制分析和样品系统分析,结果令人满意．     

工业废水中铜、镉、镍、锌离子示波极谱法同时测定

电镀车间清洗镀件的废水中含有槽液的各种成份。其中毒性较强的有镉、氰化物和铬酸盐。铜、镍、锌毒性较弱,但当含量超过允许浓度时,也有不同程度的危害。福的测定是本文重点。工业废水及地面水中铜、镉、锌的测定,通常采用双硫腙萃取比色法,镍的测定用丁二肟比色法。我们用示波极谱法在氨性底液中同时测定这四种离子。在氨性底液中Cu~(2+),Cd~(2+),Ni~(2+),Zn~(2+)离子在滴汞电极上还原产生很好的极谱波。我们用示波极谱法在1M     

ICP-AES法测定锡铅焊料中铜铁镉锌铝铋

锡铅焊料试样经盐酸、硝酸分解后，加入一定量的硫酸沉淀分离基体铅，以盐酸一氢溴酸排锡后，采用ICP—AES法同时测定铜、铁、镉、锌、铝、铋。方法没有谱线和背景干扰，检出限铜为0．000034％，铁为0．000038％，镉为0．000026％，锌为0．000071％，铝为0．00025％，铋为0．00060％，回收率在91．09／5～99．2％之间。完全满足锡铅焊料中的铜、铁、镉、锌、铝、铋测定的要求。     

银锌电池材料用无甘油玻璃纸中铜铁含量的测定

采用空气-乙炔火焰原子吸收光谱法连续测定银锌电池材料用无甘油玻璃纸中铜、铁含量。介绍铜铁最佳测定条件及呈良好线性关系的浓度范围,并对样品消化处理条件及在样品测定中的干扰因素进行了考察。样品测定结果的相对标准偏差均小于1．0％（n=10）,加标回收率为98．0％～98．5％。该法适合生产现场控制分析和样品系统分析。     

硝酸镉中铁铜锌铅的FAAS快速分析测试技术

运用FAAS快速分析硝酸镉中铁、铜、锌、铅含量,建立了铁、铜、锌、铅的共振线,灯电流,酸性介质等最佳实验条件．显示出该方法具有很好的灵敏度和材料重现性,具有方法步骤简单、操作容易、干扰少等特点．测定样品铁、铜、锌、铅含量的相对标准偏差均小于1．0％（n=10）．标准加入回收率均在97．0％～98．5％范围内．适用于硝酸镉中铁、铜、锌、铅的含量控制分析和样品系统分析．     

同时测定癌症病人血液中锌镉铅铜的微分脉冲阳极溶出伏安法

用微分脉冲阳极溶出伏安法同时测定癌症病人血液中的锌、镉、铅和铜，以为癌症与这4种微量元素在血液中含量的相关性研究提供实验数据；癌症病人血液用硝酸-高氯酸消化，消化后的白色固体加水溶解，以0．100mol/L硫酸铵为底液，在三电极体系中进行测定，以峰电位定性，峰电流定量；用该法测定了3种癌症病人血液中的锌、镉、铅和铜，相对标准偏差为2．9％—3．3％(n＝6)，加标回收率为98％—110％；该法不用除氧、干扰少、分辨率好、准确度高，适用于临床血液中锌、镉、铅和铜的测定和研究。     

镉基体分离及纯镉中杂质成分的ICP-MS法测定

研究了用阴离子交换树脂分离纯镉中铜、锌、铅、铁的条件，所得优化分离条件为：717型阴离子交换树脂柱，样品溶液为2mol/L HCl溶液；三段淋洗液依次为2mol/L HCl溶液、0．2mol/L HBr 0．25mol/L HNO3的混合酸溶液及3mol/L HNO3溶液。经ICP-MS测定证明，95％以上的镉得到分离，95％以上的铜、锌、铅、铁可以分离测定，有效地降低了ICP-MS测定纯镉中铜、锌、铅、铁时镉基体的干扰。     

火焰原子吸收法连续测定茶叶中铅、铜、锌、镉含量

采用火焰原子吸收方法连续测定了茶叶中铜，铜，锌，镉的含量，方法灵敏，准确。测定时无需富集，萃取，操作简便，回收率93．0％－98．1％，相对标准偏差不超过5．3％。     

Metal — organic interactions in sea water: an ecosystem experiment

A model plankton ecosystem was used to study the interactions of trace metals and organic compounds over a 10-day period during a phytoplankton bloom. Six bags of 1200–1 capacity were filled with coastal sea water. Three bags were spiked with copper (78, 157 and 314 nM) and one with copper (4.57 μM) plus nitrilotriacetic acid (10 μM). Samples were analysed for total dissolved copper, zinc, iron, nickel and manganese. The copper complexing capacity, determined by a method based on competition with Chelex-100 resin, was found to be essentially the same (35 nM) in all bags and independent of time. Organically bound complexes of copper (18% of the total), zinc (7%), nickel (4%) and iron (2%) were isolated by adsorption on Sep-Pak cartridges. The metal—organic complexes, were analysed on a liquid chromatograph interfaced to a multichannel atomic fluorescence detector. Organic complexes of zinc, iron and nickel were formed even in the presence of a large excess of copper. The organic and metal—organic compounds isolated by Sep-Pak cartridges became more polar as the bloom progressed.     

火焰原子吸收光谱法测定汉中石韦中微量元素含量

应用火焰原子吸收光谱法测定了汉中石韦中Fe、Cu、Zn、Mn共4种微量元素的含量。结果表明,汉中石韦中含有丰富的Fe（12．91μg／g）、Cu（32．12μg／g）、Nn（22．45μg／g）、Zn（72．84μg／g）等人体必需的微量元素,精密度不大于3．24％,回收率在93．5～106．2％之间。方法可靠,准确。     

Flow injection and microwave-oven sample decomposition for determination of copper,zinc and iron in whole blood by atomic absorption spectrometry

A simple and rapid method is proposed for the determination of copper, zinc and iron in whole blood. The injected sample is mineralized in the flow system on passage through a microwve oven and the metals are determined by atomic absorption spectrometry. Prior sample destruction or removal of organic material prior to injection is not necessary. The required volumes for each analysis are 90, 60 and 100 μl for copper, zinc and iron, respectively. The relative standard deviations were less than 3% in all cases. There was good agreement between the results obtained with the flow-injection method and those attained by conventional spectrophotometric measurements.     

火焰原子吸收法测定竹荪中的微量元素

使用灰化法处理样品,火焰原子吸收光谱法测定了竹荪中的钾、钙、钠、镁、铁、锰、铜、锌的含量。结果显示,竹荪中含有丰富的铁、锰、铜、锌4种人体必需微量元素。加标回收率为93.2%~103.2%,该法测定快速、简单,结果满意。     

Study on Determination of Six Transition Metal Ions in Biological Samples by SPE and RP‐HPLC

This paper reports the utilization of solid phase extraction and the reversed‐phase high‐performance liquid chromatography (RP‐HPLC) for the determination of six transition metal ions (iron, cobalt, nickel, copper, zinc and manganese) in biological samples. The samples were digested by microwave digestion. The iron, cobalt, nickel, copper, zinc and manganese ions in the digested samples can react with 2‐(2‐quinolinylazo)‐5‐diethylaminophenol (QADEAP) to form colored chelates in pH 4.0 acetic acid‐sodium acetic buffer solutions and cetyl trimethylammonium bromide (CTMAB) medium. These chelates were enriched by solid phase extraction with C₁₈ cartridge. Then the chelates were separated on a Waters Nova‐Pak‐C₁₈ column (3.9 × 150 mm, 5 μm) by gradient elution with methanol (containing 0.5% of acetic acid and 0.1% of CTMAB) and 0.05 mol/L pH 4.0 acetic acid‐sodium acetic buffer solution (containing 0.1% of CTMAB) as mobile phase at a flow rate of 0.5 mL/min. The detection limits of iron, cobalt, nickel, copper, zinc and manganese are 3 ng/L, 4 ng/L, 2 ng/L, 4 ng/L, 8 ng/L, 10 ng/L, respectively. This method was applied to the determination of iron, cobalt, nickel, copper, zinc and manganese in biological samples with good results.     

Determination of transition metal ions in tobacco as their 2-(2-quinolinylazo)-5-dimethylaminophenol derivatives using reversed-phase liquid chromatography with UV-VIS detection

This paper reports the utilization of solid-phase extraction and the reversed-phase high-performance liquid chromatography for the determination of six important transition metal ions: iron, cobalt, nickel, copper, zinc and manganese in tobacco with 2-(2-quinolinylazo)-5-dimethylaminophenol (QADMAP) as chelating reagent. Iron, cobalt, nickel, copper, zinc and manganese ions react with QADMAP to form colored chelates in the medium of acetic acid-sodium acetate buffer solution (pH 4.0). These chelates can be enriched by solid-phase extraction with Waters Sep-Pak-C18 cartridge, and eluted the retained chelates from cartridge with tetrahydrofuran. The chelates were separated on a Waters Nova-Pak-C18 column (150x3.9 mm, 5 microm) by gradient elution with methanol (containing 0.5% of acetic acid) and 0.05 mol/l pH 4.0 acetic acid-sodium acetate buffer solution as mobile phase at a flow-rate of 0.5 ml/min. The detection limits of iron, cobalt, nickel, copper, zinc and manganese are 10, 12, 8, 13, 17 and 22 ng/l, respectively. This method had been applied to the determination of iron, cobalt, nickel, copper, zinc and manganese in tobacco with good results.     

FAAS法连续分析测试电池锌粉中镁铁铜铅锰

提出了运用FAAS法连续分析测试电池锌粉中Mg、Fe、Cu、Pb、Mn的含量,给出了Mg、Fe、Cu、Pb、Mn最佳测定条件及线性范围,在测定中对样品中的干扰因素进行了综合考虑.方法具有很好的灵敏度和重现性,步骤简单、操作容易、干扰少.测定样品Mg、Fe、Cu、Pb、Mn含量的相对标准偏差均小于1.0%（n=10）.标准加入回收率均在97.0%-101.5%（n=6）范围内.适用于电池锌粉中Mg、Fe、Cu、Pb、Mn的含量控制分析和样品系统分析.     

微波消解原子发射光谱法测定鲍鱼中微量元素的含量

用硝酸-过氧化氢作消解液,用微波消解法处理样品,采用电感耦合等离子体原子发射光谱法测定了鲍鱼中锌、铁、锰和铜的含量。测定结果的相对标准偏差RSD<4%,加标回收率在97.4%~105.0%之间,检出限在0.764~1.539μg/L之间。该法快速、稳定、准确,结果令人满意。     

速差动力学分析法同时测定铁、锌、铜

将化学计量学方法引入速差动力学分析方法中,在不预知动力学模型参数(速率常数)的情况下,用人工神经网络(ANN)依据铁、锌、铜的EGTA配合物与PAR置换反应的速度差异,对其三组分混合体系进行了同时测定.并对人工神经网络和偏最小二乘法对多波长、多时间点的三维量测模型的解析能力进行了比较,结果表明前者总体上优于后者.混合体系中铁、锌、铜测定的相对标准偏差分别为1.63%,3.29%和4.41%.本法还被用于饲料添加剂中微量元素的测定.     

直读光谱法测定析出锌中铅、铜、铁、镉、锡、铝的含量

研究了湿法冶炼产出的析出锌,经过冲床冲压脱模、马弗炉高温熔化、模具浇铸成型、车床切削等过程,于直读光谱仪上测定析出锌中铅、铜、铁、镉、锡、铝含量的方法。通过实验确认了仪器的工作条件、熔样器皿、熔样温度、析出锌取样位置,并对熔样铸锭后铅、铜、铁、镉、锡、铝的偏析情况进行了分析,铅最大偏差达到30%,经玻璃棒搅动后保温,铅的偏差消除,拟定了直读光谱法测定析出锌中铅、铜、铁、镉、锡、铝含量的方法,应用后可以快速出具分析结果,指导生产。