PEO-LITFSI-SiO2-SN System Promotes the Application of Polymer Electrolytes in All-Solid-State Lithium-ion Batteries

All-solid-state polymer lithium-ion batteries are ideal choice for the next generation of rechargeable lithium-ion batteries due to their high energy, safety and flexibility. Among all polymer electrolytes, PEO-based polymer electrolytes have attracted extensive attention because they can dissolve various lithium salts. However, the ionic conductivity of pure PEO-based polymer electrolytes is limited due to high crystallinity and poor segment motion. An inorganic filler SiO₂ nanospheres and a plasticizer Succinonitrile (SN) are introduced into the PEO matrix to improve the crystallization of PEO, promote the formation of amorphous region, and thus improve the movement of PEO chain segment. Herein, a PEO₁₈−LiTFSI−5 %SiO₂−5 %SN composite solid polymer electrolyte (CSPE) was prepared by solution-casting. The high ionic conductivity of the electrolyte was demonstrated at 60 °C up to 3.3×10⁻⁴ S cm⁻¹. Meanwhile, the electrochemical performance of LiFePO₄/CSPE/Li all-solid-state battery was tested, with discharge capacity of 157.5 mAh g⁻¹ at 0.5 C, and capacity retention rate of 99 % after 100 cycles at 60 °C. This system provides a feasible strategy for the development of efficient all-solid-state lithium-ion batteries.     

PEO-LiClO4-ZSM5复合聚合物电解质 I. 电化学研究

首次以“择形”分子筛ZSM5为填料, 通过溶液浇铸法制得PEO-LiClO₄-ZSM5全固态复合聚合物电解质(CPE)膜. 交流阻抗实验表明ZSM5的引入可以显著地提高CPE的离子电导率. 利用交流阻抗-稳态电流相结合的方法对CPE的锂离子迁移数进行了测定, 结果表明掺入ZSM5后锂离子迁移数明显升高. ZSM5的含量为10%时, CPE同时具有最高离子电导率1.4×10^－5 S•cm^－1(25 ℃)和最大锂离子迁移数0.353. PEO-LiClO₄-ZSM5/Li电极界面稳定性实验表明PEO-LiClO₄-ZSM5复合聚合物电解质在全固态锂离子电池领域具有良好的应用前景.     

介孔材料SBA-15改性的复合凝胶聚合物电解质的制备及性能

以聚(甲基丙烯酸甲酯-聚乙二醇二甲基丙烯酸酯)(P(MMA-PEGDMA))共聚物为基体,介孔硅分子筛SBA-15为无机填料制备了复合凝胶聚合物电解质.采用原子力显微镜(AFM)、热重分析(TG)和交流阻抗(AC)等技术对其形貌、热稳定性及电化学性能进行了研究.结果表明:无机填料SBA-15与聚合物基体有较好的相容性;SBA-15的加入改善了聚合物电解质的热稳定性,提高了离子电导率,当W(SBA-15)=0.03时,离子电导率达最大值3.68×lO-3S/cm;并且掺杂SBA-15后,聚合物电解质的电化学稳定性得到了提高,其电化学稳定窗口为4.9V(vs Li /Li),可满足高性能锂离子电池的要求.     

Comparison of Li+‐ion conductivity in linear and crosslinked poly(ethylene oxide)

Polymer electrolytes are of tremendous importance for applications in modern lithium‐ion (Li⁺‐ion) batteries due to their satisfactory ion conductivity, low toxicity, reduced flammability, as well as good mechanical and thermal stability. In this study, the Li⁺‐ion conductivity of well‐defined poly(ethylene oxide) (PEO) networks synthesized via copper(I)‐catalyzed azide–alkyne cycloaddition is investigated by electrochemical impedance spectroscopy after addition of different lithium salts. The ion conductivity of the network electrolytes increases with increasing molar mass of the PEO chains between the junction points which is completely opposite to the behavior of their respective uncrosslinked linear precursors. Obviously, this effect is directly related to the segmental mobility of the PEO chains. Furthermore, the ion conductivity of the network electrolytes under investigation increases also with increasing size of the anion of the added lithium salt due to a weaker anti‐plasticizing effect of the more bulky anions. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 21–28     

Electrochemical properties of PEO/PMMA blend-based polymer electrolytes using imidazolium salt-supported silica as a filler

In this study, the composite polymer electrolytes (CPEs) were prepared by solution casting technique. The CPEs consisted of PEO/PMMA blend as a host matrix doped with LiClO₄. Propylene carbonate (PC) was used as plasticizer and a small amount of imidazolium salt-supported amorphous silica (IS-AS) as a filler was prepared by the sol–gel method. At room temperature, the highest conductivity was obtained for the composition having PEO–PMMA–LiClO₄–PC–4wt. % IS-AS with a value of 1.15 × 10^?4 S/cm. In particular, the CPE using the IS-AS filler showed a higher conductivity than any other sample (fumed silica, amorphous silica). Studies of differential scanning calorimetry and scanning electron microscopy indicated that the ionic conductivity increase was due to an expansion in the amorphous phase which enhances the flexibility of polymeric chains and the homogeneous structure of CPEs. It was found that the ionic conductivity and interfacial resistance stability of CPEs was significantly improved by the addition of IS-AS. In other words, the resistance stability and maximum ambient ionic conductivity of CPEs containing IS-AS filler were better than CPEs containing any other filler.     

Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

Effect of NiO nanofiller concentration on the properties of PEO-NiO-LiClO4 composite polymer electrolyte

Composite polymer electrolyte films comprising polyethylene oxide (PEO) as the polymer host, LiClO₄ as the dopant, and NiO nanoparticle as the inorganic filler was prepared by solution casting technique. NiO inorganic filler was synthesized via sol-gel method. The effect of NiO filler on the ionic conductivity, structure, and morphology of PEO-LiClO₄-based composite polymer electrolyte was investigated by AC impedance spectroscopy, X-ray diffraction, and scanning electron microscopy, respectively. It was observed that the conductivity of the electrolyte increases with NiO concentration. The highest room temperature conductivity of the electrolyte was 7.4?×?10^?4 S cm^?1 at 10 wt.% NiO. The observation on structure shows the highest conductivity appears in amorphous phase. This result has been supported by surface morphology analysis showing that the NiO filler are well distributed in the samples. As a conclusion, the addition of NiO nanofiller improves the conductivity of PEO-LiClO₄ composite polymer electrolyte.     

Nano lithium aluminate filler incorporating gel lithium triflate polymer composite: Preparation,characterization and application as an electrolyte in lithium ion batteries

Gel polymer composites electrolytes containing nano LiAlO₂ as filler were prepared using a solution cast technique and characterized using different techniques such as X-ray diffraction (XRD), thermal analysis (TG, DSC), Fourier transform infra – red spectroscopy (FT-IR) and scanning electron microscope (SEM). X-ray diffraction analysis showed the effect of lithium tri fluoro methane sulphonate (LiCF₃SO₃), poly vinyl acetate (PVAc) and nano lithium aluminate (LiAlO₂) on the crystalline structure of the poly vinylidene fluoride –co– hexa fluoro propylene (PVDF-co-HFP) matrix containing ethylene carbonate (EC) and diethyl carbonate (DEC) as plasticizers. FT-IR analysis confirmed both the good dissolution of the LiCF₃SO₃ salt and the good interaction of the nano LiAlO₂ filler with the polymer matrix. TG analysis showed the good thermal stability of the LiAlO₂ samples compared to the free one. Also, addition of nano LiAlO₂ filler enhanced the conductivity value of the polymer composites electrolytes. The sample containing 2 wt% of LiAlO₂ showed the highest conductivity value, 4.98 × 10⁻³ Ω ⁻¹ cm⁻¹ at room temperature, with good thermal stability behavior (T_d = 362 °C). This good conductive and thermally stable polymer nano composite electrolyte was evaluated as a promising membrane for lithium ion batteries application.     

Conductivity,thermal and morphology studies of PEO based salted polymer electrolytes

Polymer electrolyte has been prepared via solution-casting technique. The polymer electrolytes are formed from polyethylene oxide (PEO) and lithium hexafluorate is used as the doping salt. The conductivity increases from 10⁻⁹ to 10⁻⁴ S cm⁻¹ upon the addition of various concentrations of salt. The results reveal that the conductivity increases with increasing temperature when the salt concentration increases up to 20 wt% The conductivity for 20 wt% of salt remains similar to the conductivity for 15 wt% of salt at 318 K. Differential scanning calorimetry studies show that the melting transition temperature and crystallinity decreases upon the addition of various concentrations of salt. Thermogravimetric analysis (TGA) results indicate that a significant effect on the thermal stability of polyethylene–lithium salt composites. SEM images reveal that the morphology of polymer electrolyte's surface changes when various concentrations of salt are added into the polymer system.     

Effect of nanoporous alumina filler on conductivity enhancement in PEO9(MgClO4)2 polymer electrolyte: a 1H NMR study

Ionic conductivity, differential scanning calorimetry (DSC), and ¹H nuclear magnetic resonance (NMR) measurements have been performed on (PEO)₉Mg(ClO₄)₂ and (PEO)₉Mg(ClO₄)₂ + Al₂O₃ (neutral, nanoporous) polymer electrolyte systems. It is observed that the conductivity enhances due to the presence of filler up to 15 wt.% and then decreases. The NMR results are consistent with the idea that the conductivity enhancement is mainly due to the increase in chain mobility and ionic mobility of the solid polymer electrolyte caused by increased amorphocity of the electrolyte due to the presence of filler. DSC results also demonstrate that the fraction of the amorphous phase has increased due to the addition of the filler.     

Effect of plasticizers (EC or PC) on the ionic conductivity and thermal properties of the (PEO)9LiTf: Al2O3 nanocomposite polymer electrolyte system

A new plasticized nanocomposite polymer electrolyte based on poly (ethylene oxide) (PEO)-LiTf dispersed with ceramic filler (Al₂O₃) and plasticized with propylene carbonate (PC), ethylene carbonate (EC), and a mixture of EC and PC (EC+PC) have been studied for their ionic conductivity and thermal properties. The incorporation of plasticizers alone will yield polymer electrolytes with enhanced conductivity but with poor mechanical properties. However, mechanical properties can be improved by incorporating ceramic fillers to the plasticized system. Nanocomposite solid polymer electrolyte films (200–600 μm) were prepared by common solvent-casting method. In present work, we have shown the ionic conductivity can be substantially enhanced by using the combined effect of the plasticizers as well as the inert filler. It was revealed that the incorporating 15 wt.% Al₂O₃ filler in to PEO: LiTf polymer electrolyte significantly enhanced the ionic conductivity [σ _RT (max)?=?7.8?×?10^?6 S cm^?1]. It was interesting to observe that the addition of PC, EC, and mixture of EC and PC to the PEO: LiTf: 15 wt.% Al₂O₃ CPE showed further conductivity enhancement. The conductivity enhancement with EC is higher than PC. However, mixture of plasticizer (EC+PC) showed maximum conductivity enhancement in the temperature range interest, giving the value [σ _RT (max)?=?1.2?×?10^?4 S cm^?1]. It is suggested that the addition of PC, EC, or a mixture of EC and PC leads to a lowering of glass transition temperature and increasing the amorphous phase of PEO and the fraction of PEO-Li⁺ complex, corresponding to conductivity enhancement. Al₂O₃ filler would contribute to conductivity enhancement by transient hydrogen bonding of migrating ionic species with O–OH groups at the filler grain surface. The differential scanning calorimetry thermograms points towards the decrease of T _g , crystallite melting temperature, and melting enthalpy of PEO: LiTf: Al₂O₃ CPE after introducing plasticizers. The reduction of crystallinity and the increase in the amorphous phase content of the electrolyte, caused by the filler, also contributes to the observed conductivity enhancement.     

A new composite polymer electrolyte based on poly(ethyleneoxide)/ polysiloxane/BMImTFSI/organomontmorillonite

Composite polymer electrolytes based on poly(ethylene oxide)-polysiloxane/l-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide/organomontmorillonite(PEO-PDMS/1L/OMMT) were prepared and characterized.Addition of both an ionic liquid and OMMT to the polymer base of PEO-PDMS resulted in an increase in ionic conductivity.At room temperature,the ionic conductivity of sample PPB100-OMMT4 was 2.19×10~3 S/cm.The composite polymer electrolyte also exhibited high thermal and electrochemical stability and may potentially be applied in lithium batteries.     

Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber–titanium dioxide–lithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol–gel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4 × 10⁻⁵ S cm⁻¹ was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.

     

Nanocomposite solid polymeric electrolyte of 49% poly(methyl methacrylate)-grafted natural rubber�Ctitanium dioxide�Clithium tetrafluoroborate (MG49-TiO2-LiBF4)

A nanocomposite polymer electrolyte consisting of 49% poly(methyl methacrylate)-grafted natural rubber (MG49) as a polymer matrix, lithium tetrafluoroborate (LiBF₄) as a dopant salt, and titanium dioxide (TiO₂) as an inert ceramic filler was prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by a sol?Cgel process. The ionic conductivity was investigated by alternating current impedance spectroscopy. X-ray diffraction (XRD) was used to determine the structure of the electrolyte, and its morphology was examined by scanning electron microscopy (SEM). The highest conductivity, 1.4?×?10^?5 S cm^?1 was obtained at 30 wt.% of LiBF₄ salt addition with 6 wt.% of TiO₂ filler content. Ionic conductivity was found to increase with the increase of salt concentration. The optimum value of conductivity was found at 6 wt.% of TiO₂. The XRD analysis revealed that the crystalline phase of the polymer host slightly decreased with the addition of salt and filler. The SEM analysis showed that the smoother the surface of the electrolyte, the higher its conductivity.     

Effect of solvated ionic liquids on the ion conducting property of composite membranes for lithium ion batteries

We prepared the polyethylene oxide (PEO)-based composite membrane electrolytes which contained the specialized ionic liquids and the inorganic filler of Li₇La₃Zr₂O₁₂ (LLZO). Mixtures of ionic liquids and tetragonal inorganic fillers were used as additives to prepare composite electrolytes for an application of all solid-state lithium ion batteries (ASLBs). In order to improve the ionic conductivity of composite membranes, we studied the structural change and the electrochemical behaviors as a function of the amounts of solvated ionic liquids (ILs). The addition effect of solvated ILs showed the higher ionic conductivity such as 10^?4 S/cm at 55 °C by reducing the crystalline character of polymer based composite, resulting in the enhanced ion conducting property. The hybrid composite membranes were successfully made in flexible form, and have an excellent thermal and electrochemical stability. Finally, the electrochemical performance of the half-cell was evaluated, and it was confirmed that the ion-conducting characteristics were influenced and controlled by the effect of ILs.     

Investigation on the effect of nanosilica towards corn starch–lithium perchlorate-based polymer electrolytes

Biodegradable corn starch–lithium perchlorate (LiClO₄)-based solid polymer electrolytes with addition of nano-sized fumed silica (SiO₂) were prepared by solution casting technique. Ionic conductivity at ambient temperature was measured by AC impedance spectroscopy. Upon addition of nano-sized SiO₂, the ionic conductivity at room temperature is increased. The optimum ionic conductivity value obtained was 1.23?×?10^?4?S?cm^?1 at 4?wt% SiO₂. This may be attributed to the low crystallinity of the polymer electrolytes resulting from the dispersed nanosilica particles. Fourier–transform infrared spectroscopy studies confirmed the complexation between corn starch, lithium perchlorate, and silica. The thermal properties of the prepared samples were investigated with differential scanning calorimetry and thermogravimetric analysis. The surface morphology of the polymer electrolytes confirmed the agglomeration of particles after excess dispersion of inorganic filler. This was proven in the scanning electron microscopy studies.     

Influence of barium titanate nanofiller on PEO/PVdF-HFP blend-based polymer electrolyte membrane for Li-battery applications

Organic-inorganic hybrid membranes based on poly(ethylene oxide) (PEO) 6.25 wt%/poly(vinylidene fluoride hexa fluoro propylene) [P(VdF-HFP)] 18.75 wt% were prepared by using various concentration of nanosized barium titanate (BaTiO₃) filler. Structural characterizations were made by X-ray diffraction and Fourier transform infrared spectroscopy, which indicate the inclusion of BaTiO₃ in to the polymer matrix. Addition of filler creates an effective route of polymer-filler interface and promotes the ionic conductivity of the membranes. From the ionic conductivity results, 6 wt% of BaTiO₃-incorporated composite polymer electrolyte (CPE) showed the highest ionic conductivity (6 × 10^?3 Scm^?1 at room temperature). It is found that the filler content above 6 wt% rendered the membranes less conducting. Morphological images reveal that the ceramic filler was embedded over the membrane. Thermogravimetric and differential thermal analysis (TG-DTA) of the CPE sample with 6 wt% of the BaTiO₃ shows high thermal stability. Electrochemical performance of the composite polymer electrolyte was studied in LiFePO₄/CPE/Li coin cell. Charge-discharge cycle has been performed for the film exhibiting higher conductivity. These properties of the nanocomposite electrolyte are suitable for Li-batteries.     

Enhanced ionic conductivity of poly(ethylene oxide) (PEO) electrolyte by adding mesoporous molecular sieve LiAlSBA

Mesoporous molecular sieve LiAlSBA was prepared via an ion exchange process with mesoporous AlSBA directly, which has a regular 2D hexagonal structure with pore size about 7 nm. It was added into poly(ethylene oxide) (PEO) solid electrolyte as filler. The characteristics of the composite polymer electrolyte were determined by XRD, DSC, TGA, FTIR, PLM and electrochemical methods. Compared with bare PEO electrolyte, the adding of dispersed LiAlSBA powder improved the ionic conductivity of PEO polymer electrolyte more than three orders. The reason for it is that mesoporous LiAlSBA powder acts as crystal cores in PEO composite electrolyte and fines the crystallites, decreases the crystallinity, which provides much more continuous amorphous domain for Li⁺ moving easily in PEO electrolyte. Besides, lithium ions of the mesoporous molecular sieves can hop from one site to another along the surface of the mesoporous channels, this mechanism is absent in the case of common nano-ceramic fillers in PEO electrolyte.     

All solid polymer electrolytes based on polar side group rotation for rechargeable lithium batteries

A novel polymer matrix with a polar carbonyl group was designed and used to prepare an all‐solid polymer electrolyte in lithium rechargeable batteries. The ionic conductivity of this type of polymer electrolyte was examined. The relationship between the lithium salt concentration and ionic conductivity was investigated by Fourier transform infrared (FTIR) spectroscopy. The carbonyl groups in the polymer matrix effectively interacted with the lithium salt, which improved the ionic conductivity at a large range of temperatures. The ionic conductivity of this type of polymer electrolyte was approximately 10^?4 S cm^?1 at room temperature. The stability of the interface between electrode and electrolyte was evaluated by measuring the alternating current (AC) impedance. Copyright © 2009 John Wiley & Sons, Ltd.     

Structural,thermal, vibrational,and electrochemical behavior of lithium ion conducting solid polymer electrolyte based on poly(vinyl alcohol)/poly(vinylidene fluoride) blend

The present study focuses on the preparation and characterization of poly(vinyl alcohol)/poly(vinylidene fluoride) blend polymer electrolyte doped with lithium triflate (LiCF₃SO₃). Interaction of lithium triflate with the host polymer in the solid polymer electrolyte was studied using X-ray diffraction, Fourier transform infrared spectroscopy and differential scanning calorimetry analysis. It was found that 15% salt doped polymer electrolyte possesses the highest ionic conductivity (2.7 × 10^–3 S/cm) at 303 K, the higher thermal stability at 175°C. Linear sweep voltammetry results revealed that the film is electrochemically stable up to 3.4 V.