Free convection heat transfer from an isothermal plate with arbitrary inclination

This paper presents a new formulation for the laminar free convection from an arbitrarily inclined isothermal plate to fluids of any Prandtl number between 0.001 and infinity. A novel inclination parameter is proposed such that all cases of the horizontal, inclined and vertical plates can be described by a single set of transformed equations. Moreover, the self-similar equations for the limiting cases of the horizontal and vertical plates are recovered from the transformed equations by setting=0 and=1, respectively. Heated upward-facing plates with positive and negative inclination angles are investigated. A very accurate correlation equation of the local Nusselt number is developed for arbitrary inclination angle and for 0.001 Pr .

---

Wärmeübertragung bei freier Konvektion an einer isothermen Platte mit beliebiger Neigung

Zusammenfasssung Diese Untersuchung stellt eine neue Formulierung der laminaren freien Konvektion von Flüssigkeiten mit einer Prandtl-Zahl zwischen 0,001 und unendlich an einer beliebig schräggestellten isothermen Platte dar. Ein neuer Neigungsparameter wird eingeführt, so daß alle Fälle der horizontalen, geneigten oder vertikalen Platte von einem einzigen Satz transformierter Gleichungen beschrieben werden können. Die unabhängigen Gleichungen für die beiden Fälle der horizontalen and vertikalen Platte wurden für=0 und=1 aus den transformierten Gleichungen wieder abgeleitet. Es wurden erwärmte aufwärtsgerichtete Platten mit positiven und negativen Neigungswinkeln untersucht. Eine sehr genaue Gleichung wurde für die lokale Nusselt-Zahl bei beliebigen Neigungswinkeln und für 0,001 Pr entwickelt.

---

Nomenclature C _p specific heat - f reduced stream function - g gravitational acceleration - Gr local Grashof number,g(T _w –T _w ) x³/v² - h local heat transfer coefficient - k thermal conductivity - n constant exponent - Nu local Nusselt number,hx/k - p pressure - Pr Prandtl number, v/ - Ra local Rayleigh number,g(T _w –T )J x³/v - T fluid temperature - T _w wall temperature - T temperature of ambient fluid - u velocity component in x-direction - v velocity component in y-direction - x coordinate parallel to the plate - y coordinate normal to the plate Greek symbols thermal diffusivity - thermal expansion coefficient - (Ra¦sin¦)^1/4/( Ra cos()^1/5 - pseudo-similarity variable, (y/) - dimensionless temperature, (T–T )/(T _w–T ) - ( Ra cos)^1/5+(Rasin)^1/4 - v kinematic viscosity - 1/[1 +(Ra cos)^1/5/( Ra¦sin)^1/4] - density of fluid - Pr/(1+Pr) - _w wall shear stress - angle of plate inclination measured from the horizontal - stream function - dimensionless dynamic pressure     

Mean and turbulent velocity measurements of supersonic mixing layers

The behavior of supersonic mixing layers under three conditions has been examined by schlieren photography and laser Doppler velocimetry. In the schlieren photographs, some large-scale, repetitive patterns were observed within the mixing layer; however, these structures do not appear to dominate the mixing layer character under the present flow conditions. It was found that higher levels of secondary freestream turbulence did not increase the peak turbulence intensity observed within the mixing layer, but slightly increased the growth rate. Higher levels of freestream turbulence also reduced the axial distance required for development of the mean velocity. At higher convective Mach numbers, the mixing layer growth rate was found to be smaller than that of an incompressible mixing layer at the same velocity and freestream density ratio. The increase in convective Mach number also caused a decrease in the turbulence intensity ( _u/U).List of symbols a speed of sound - b total mixing layer thickness between U ₁ – 0.1 U and U ₂ + 0.1 U - f normalized third moment of u-velocity, f u³/(U)³ - g normalized triple product of u² , g u²/(U)³ - h normalized triple product of u ², h u ²/(U)³ - l _u axial distance for similarity in the mean velocity - l _u axial distance for similarity in the turbulence intensity - M Mach number - M _c convective Mach number (for ₁ = ₂), M _c (U ₁ – U ₂)/(a ₁ + a ₂) - P static pressure - r freestream velocity ratio, r U ₂/U ₁ - Re unit Reynolds number, Re U/ - s freestream density ratio, s ₂/₁ - T _t total temperature - u instantaneous streamwise velocity - u deviation of u-velocity, uu – U - U local mean streamwise velocity - U ₁ primary freestream velocity - U ₂ secondary freestream velocity - average of freestream velocities, (U ₁ + U ₂)/2 - U freestream velocity difference, U U ₁ – U ₂ - instantaneous transverse velocity - v deviation of -velocity, – V - V local mean transverse velocity - x streamwise coordinate - y transverse coordinate - y ₀ transverse location of the mixing layer centerline - ensemble average - ratio of specific heats - boundary layer thickness (y-location at 99.5% of free-stream velocity) - similarity coordinate, (y – y ₀)/b - compressible boundary layer momentum thickness - viscosity - density - standard deviation - dimensionless velocity, (U – U ₂)/U - 1 primary stream - 2 secondary stream A version of this paper was presented at the 11th Symposium on Turbulence, October 17–19, 1988, University of Missouri-Rolla     

Reservoir transport equations by compositional approach

The objective of this paper is to present an overview of the fundamental equations governing transport phenomena in compressible reservoirs. A general mathematical model is presented for important thermo-mechanical processes operative in a reservoir. Such a formulation includes equations governing multiphase fluid (gas-water-hydrocarbon) flow, energy transport, and reservoir skeleton deformation. The model allows phase changes due to gas solubility. Furthermore, Terzaghi's concept of effective stress and stress-strain relations are incorporated into the general model. The functional relations among various model parameters which cause the nonlinearity of the system of equations are explained within the context of reservoir engineering principles. Simplified equations and appropriate boundary conditions have also been presented for various cases. It has been demonstrated that various well-known equations such as Jacob, Terzaghi, Buckley-Leverett, Richards, solute transport, black-oil, and Biot equations are simplifications of the compositional model.Notation List B reservoir thickness - B formation volume factor of phase - Cⁱ mass of component i dissolved per total volume of solution - C ⁱ mass fraction of component i in phase - C heat capacity of phase at constant volume - C_p heat capacity of phase at constant pressure - D ⁱ hydrodynamic dispersion coefficient of component i in phase - D_MTf thermal liquid diffusivity for fluid f - F = F(x, y, z, t) defines the boundary surface - f_p fractional flow of phase - g gravitational acceleration - H_p enthalpy per unit mass of phase - J_p volumetric flux of phase - k_rf relative permeability to fluid f - k₀ absolute permeability of the medium - M_p ⁱ mass of component i in phase - n porosity - N rate of accretion - P_f pressure in fluid f - p_ca capillary pressure between phases and =p-p - Rⁱ rate of mass transfer of component i from phase to phase - Rⁱ _source source rate of component i within phase - S saturation of phase - s gas solubility - T temperature - t time - U displacement vector - u velocity in the x-direction - v velocity in the y-direction - V volume of phase - V_s velocity of soil solids - W_i body force in coordinate direction i - x horizontal coordinate - z vertical coordinate Greek Letters _p volumetric coefficient of compressibility - _T volumetric coefficient of thermal expansion - _ij Kronecker delta - volumetric strain - _m thermal conductivity of the whole matrix - internal energy per unit mass of phase - gf suction head - density of phase - _ij tensor of total stresses - _ij tensor of effective stresses - volumetric content of phase - f viscosity of fluid f     

Pressure pulsations during interaction between a subsonic jet and the subsonic section of a supersonic jeton a flat obstacle

Pressure pulsations were measured during in-leakage of a subsonic jet and the subsonic section of a heated supersonic jet on a flat obstacle. Data have been obtained on the total and spectrum levels of the pressure pulsations at different spacings X of the obstacle from the nozzle exit. It is shown that when the obstacle is disposed at the section of the jet where the local velocity is subsonic, the pulsation levels outside the dependence on the conditions at the nozzle exit (Mach number Maxa 0 a 3.0; stagnation temperature T₀=280–1200K) vary in direct proportion to the local velocity head q. The ratio between the total level and q is (/g)=0.2–0.3. It is established that for a subsonic velocity ahead of the obstacle, all the spectra obtained for different values of M _a , T₀, d _a and X in the coordinates Sh=f(d/V) and (₁*/q)(V/d) will lie on a single generalized spectrum. Here ₁* is the pulsation level in a 1-Hz band, and d and V are, respectively, the jet diameter and velocity directly in front of the obstacle.Translated from Izvestiya Akademiya Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 5, pp. 172–174, September–October, 1975.     

Transport in ordered and disordered porous media II: Generalized volume averaging

In this paper we develop the averaged form of the Stokes equations in terms of weighting functions. The analysis clearly indicates at what point one must choose a media-specific weighting function in order to achieve spatially smoothed transport equations. The form of the weighting function that produces the cellular average is derived, and some important geometrical theorems are presented.Roman Letters A interfacial area of the- interface associated with the local closure problem, m² - A _e area of entrances and exits for the-phase contained within the averaging system, m² - A _p surface area of a particle, m² - d _p 6V _p/A_p, effective particle diameter, m - g gravity vector, m/s² - I unit tensor - K _m permeability tensor for the weighted average form of Darcy's law, m² - L general characteristic length for volume averaged quantities, m - L _p general characteristic length for volume averaged pressure, m - L characteristic length for the porosity, m - L _v characteristic length for the volume averaged velocity, m - l characteristic length (pore scale) for the-phase - l _i i=1, 2, 3 lattice vectors, m - (y) weighting function - m(–y) (y), convolution product weighting function - _v special weighting function associated with the traditional averaging volume - m _v special convolution product weighting function associated with the traditional averaging volume - m _g general convolution product weighting function - m _V unit cell convolution product weighting function - m _C special convolution product weighting function for ordered media which produces the cellular average - m _D special convolution product weighting function for disordered media - m _M master convolution product weighting function for ordered and disordered media - n unit normal vector pointing from the-phase toward the-phase - p pressure in the-phase, N/m² - p_m superficial weighted average pressure, N/m² - p _m intrinsic weighted average pressure, N/m² - p traditional intrinsic volume averaged pressure, N/m² - p p p _m , spatial deviation pressure, N/m² - r ₀ radius of a spherical averaging volume, m - r _m support of the convolution product weighting function, m - r position vector, m - r position vector locating points in the-phase, m - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ - V _cell volume of a unit cell, m³ - V velocity vector in the-phase, m/s - vm superficial weighted average velocity, m/s - v _m intrinsic weighted average velocity, m/s - V volume of the-phase contained in the averaging volume, m³ - V _p volume of a particle, m³ - v traditional superficial volume averaged velocity, m/s - v v p _m spatial deviation velocity, m/s - x position vector locating the centroid of the averaging volume or the convolution product weighting function, m - y position vector relative to the centroid, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters indicator function for the-phase - Dirac distribution associated with the- interface - V /V, volume average porosity - _m m * . weighted average porosity - mass density of the-phase, kg/m³ - viscosity of the-phase, Ns/m² - V /V, volume fraction of the-phase     

Mixed convection flow in narrow vertical ducts

The mixed convection flow in a vertical duct is analysed under the assumption that , the ratio of the duct width to the length over which the wall is heated, is small. It is assumed that a fully developed Poiseuille flow has already been set up in the duct before heat from the wall causes this to be changed by the action of the buoyancy forces, as measured by a buoyancy parameter . An analytical solution is derived for the case when the Reynolds numberRe, based on the duct width, is of 0 (1). This is extended to the case whenRe is 0 (^–1) by numerical integrations of the governing equations for a range of values of representing both aiding and opposing flows. The limiting cases, || 1 andR=Re of 0 (1), andR and both large, with of 0 (R ^1/3) are considered further. Finally, the free convection limit, large with R of 0 (1), is discussed.

---

Mischkonvektion in engen senkrechten Rohren

Zusammenfassung Mischkonvektion in einem senkrechten Rohr wird unter der Voraussetzung untersucht, daß das Verhältnis der Rohrbreite zur Länge, über welche die Wand beheizt wird, klein ist. Es wird angenommen, daß sich bereits eine voll entwickelte Poiseuille-Strömung in dem Rohr eingestellt hat, bevor Antriebskräfte, gemessen mit dem Auftriebsparameter , aufgrund der Wandbeheizung die Strömung verändern. Es wird eine analytische Lösung für den Fall erhalten, daß die mit der Rohrbreite als charakteristische Länge gebildete Reynolds-ZahlRe konstant ist. Dies wird mittels einer numerischen Integration der wichtigsten Gleichungen auf den FallRe =f (^–1) sowohl für Gleich- als auch für Gegenstrom ausgedehnt. Weiterhin werden die beiden Grenzfälle betrachtet, wenn || 1 undR=Re konstant ist, sowieR und beide groß mit proportionalR ^1/3. Schließlich wird der Grenzfall der freien Konvektion, großes mit konstantem R, diskutiert.

---

Nomenclature g acceleration due to gravity - Gr Grashof number - G modified Grashof number - h duct width - l length of the heated section of the duct wall - p pressure - Pr Prandtl number - Q flow rate through the duct - Q ₀ heat transfer on the wally=0 - Q ₁ heat transfer on the wally=1 - Re Reynolds number - R modified Reynolds number - T temperature of the fluid - T ₀ ambient temperature - T applied temperature difference - u, velocity component in thex-direction - v, velocity component in they-direction - x, co-ordinate measuring distance along the duct - y, co-ordinate measuring distance across the duct - buoyancy parameter - ₀ modified buoyancy parameter, ₀=R ^–1/3 - coefficient of thermal expansion - ratio of duct width to heated length, =h/l - (non-dimensional) temperature - _w applied temperature on the wally=0 - kinematic viscosity - density of the fluid - ₀ shear stress on the wally=0 - ₁ shear stress on the wally=1 - stream function     

Measurement of the relaxation time in Darcy flow

The inertia of a liquid flowing through a porous medium is normally ignored, but if the acceleration is great, it may be important. The relaxation time, defined so that it alone accounts for the inertia, has been determined experimentally with a simple oscillator. A U-Tube is provided with a porous plug and filled with a liquid. During pendulation of the liquid, the frequency and the damping define the relaxation time. The measured value of the relaxation time is about 10 times the theoretical estimate derived from Navier-Stokes equation.Symbols E modulus of elasticity - E _D dissipated energy - E _k kinetic energy - g acceleration of gravity - G pressure gradient - h height - K ₀ permeability - L length of porous plug - n porosity - P dissipated power - pressure - R half the tube length - R _c radius of the tube bend - r radial coordinate - r _o radius of the tube - s coordinate along a streamline in the tube - t time - v flux per unit area - it relaxation time - , auxiliary variables - , v dynamic and kinematic viscosity - , velocity potential for inviscid flow and gravity potential - dissipation function - displacement of the liquid - , _o frequency of damped and undamped oscillations     

On the closure problem for Darcy's law

In a previous derivation of Darcy's law, the closure problem was presented in terms of an integro-differential equation for a second-order tensor. In this paper, we show that the closure problem can be transformed to a set of Stokes-like equations and we compare solutions of these equations with experimental data. The computational advantages of the transformed closure problem are considerable.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the averaging volume, m² - B second-order tensor used to respresent the velocity deviation - b vector used to represent the pressure deviation, m^–1 - C second-order tensor related to the permeability tensor, m^–2 - D second-order tensor used to represent the velocity deviation, m² - d vector used to represent the pressure deviation, m - g gravity vector, m/s² - I unit tensor - K C ^–1,–D, Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the-phase, m - l _i i=1, 2, 3, lattice vectors, m - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - p pressure in the-phase, N/m ² - p intrinsic phase average pressure, N/m² - p –p , spatial deviation of the pressure in the-phase, N/m² - r position vector locating points in the-phase, m - r ₀ radius of the averaging volume, m - t time, s - v velocity vector in the-phase, m/s - v intrinsic phase average velocity in the-phase, m/s - v phase average or Darcy velocity in the \-phase, m/s - v –v , spatial deviation of the velocity in the-phase m/s - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ Greek Letters V /V volume fraction of the-phase - mass density of the-phase, kg/m³ - viscosity of the-phase, Nt/m²     

Flow in vicinity of blunt body stagnation point in diverging hypersonic stream

In the hypersonic thin shock layer approximation for a small ratio k of the densities before and after the normal shock wave the solution of [1] for the vicinity of the stagnation point of a smooth blunt body is extended to the case of nonuniform outer flow. It is shown that the effect of this nonuniformity can be taken into account with the aid of the effective shock wave radius of curvature R_*, whose introduction makes it possible to reduce to universal relations the data for different nonuniform outer flows with practically the same similarity criterion k. The results of the study are compared with numerical calculations of highly underexpanded jet flow past a sphere.Notations x, y a curvilinear coordinate system with axes directed respectively along and normal to the body surface with origin at the forward stagnation point - R radius of curvature of the meridional plane of the body surface - uV, vV., , p V ² respectively the velocity projections on the x, y axes, density, and pressure - and V freestream density and velocity The indices =0 and=1 apply to plane and axisymmetric flows Izv. AN SSSR, Mekhanika Zhidkosti i Gaza, Vol. 5, No. 3, pp. 102–105, 1970.     

The dynamic and steady shear properties of synovial fluid and of the components making up synovial fluid

Steady-shear and dynamic properties of a pooled sample of cattle synovial fluid have been measured using techniques developed for low viscosity fluids. The rheological properties of synovial fluid were found to exhibit typical viscoelastic behaviour and can be described by the Carreau type A rheological model. Typical model parameters for the fluid are given; these may be useful for the analysis of the complex flow problems of joint lubrication.The two major constituents, hyaluronic acid and proteins, have been successfully separated from the pooled sample of synovial fluid. The rheological properties of the hyaluronic acid and the recombined hyaluronic acid-protein solutions of both equal and half the concentration of the constituents found in the original synovial fluid have been measured. These properties, when compared to those of the original synovial fluid, show an undeniable contribution of proteins to the flow behaviour of synovial fluid in joints. The effect of protein was found to be more prominent in hyaluronic acid of half the normal concentration found in synovial fluid, thus providing a possible explanation for the differences in flow behaviour observed between synovial fluid from certain diseased joints compared to normal joint fluid.Nomenclature A Ratio of angular amplitude of torsion head to oscillation input signal - G Storage modulus - G Loss modulus - I Moment of inertia of upper platen — torsion head assembly - K Restoring constant of torsion bar - N ₁ First normal-stress difference - R Platen radius - S ⁽ⁱ⁾ Geometric factor in the dynamic property analysis - t ₁ Characteristic time parameter of the Carreau model - X, Y Carreau model parameters - Z () Reimann Zeta function of - Carreau model parameter - Shear rate - Apparent steady-shear viscosity - ^* Complex dynamic viscosity - Dynamic viscosity - Imaginary part of the complex dynamic viscosity - ₀ Zero-shear viscosity - ₀ Cone angle - Carreau model characteristic time - Density of fluid - Shear stress - Phase difference between torsion head and oscillation input signals - ₀ Zero-shear rate first normal-stress coefficient - Oscillatory frequency     

Die Torsionsspannungen in Wellen mit tiefen Längsnuten

Übersicht MitF(x, y) als Spannungsfunktion einer Welle ohne Nut und(, y) als Potentialfunktion des Quelle-Senke-Systems erhält man Spannungsfunktionen(, y) =F(x, y) –(, y) für Wellen mit tiefen Längsnuten. Es wird gezeigt, daß sich damit die Schubspannungen in den Läufern von Schraubenverdichtern ermitteln lassen.

---

Shearing stresses in shafts with deep longitudinal grooves

Summary The stress functions(, y) of shafts with deep longitudinal grooves may be represented by(, y) =F(x, y) –(, y) whereF(x, y) is the stress function of a cylindrical shaft without grooves and(, y) denotes the potential function of the source-sink system. It is shown that the shearing stresses in rotors of screw-compressors may be obtained in this way.

     

Flow of second-order fluids over an enclosed rotating disc

Summary This paper is devoted to a study of the flow of a second-order fluid (flowing with a small mass rate of symmetrical radial outflow m, taken negative for a net radial inflow) over a finite rotating disc enclosed within a coaxial cylinderical casing. The effects of the second-order terms are observed to depend upon two dimensionless parameters ₁ and ₂. Maximum values ₁ and ₂ of the dimensionless radial distances at which there is no recirculation, for the cases of net radial outflow (m>0) and net radial inflow (m<0) respectively, decrease with an increase in the second-order effects [represented by T(=₁+₂)]. The velocities at ₁ and ₂ as well as at some other fixed radii have been calculated for different T and the associated phenomena of no-recirculation/recirculation discussed. The change in flow phenomena due to a reversal of the direction of net radial flow has also been studied. The moment on the rotating disc increases with T.Nomenclature , , z coordinates in a cylindrical polar system - z ₀ distance between rotor and stator (gap length) - =/z ₀, dimensionless radial distance - =z/z ₀, dimensionless axial distance - _s = _s/z₀, dimensionless disc radius - V =(u, v, w), velocity vector - dimensionless velocity components - uniform angular velocity of the rotor - , p fluid density and pressure - P =p/(₂ z ₀₂ ² , dimensionless pressure - ₁, ₂, ₃ kinematic coefficients of Newtonian viscosity, elastico-viscosity and cross-viscosity respectively - ₁, _{2 2}/z ₀ ² , resp. ₃/z ₀ ² , dimensionless parameters representing the ratio of second-order and inertial effects - m = , mass rate of symmetrical radial outflow - l a number associated with induced circulatory flow - Rm =m/(z ₀₁), Reynolds number of radial outflow - R _l =l/(z ₀₁), Reynolds number of induced circulatory flow - Rz =z ₀ ² /₁, Reynolds number based on the gap - ₁, ₂ maximum radii at which there is no recirculation for the cases Rm>0 and Rm<0 respectively - ₁(T), ₂(T) ₁ and ₂ for different T - U _1(T) ⁽⁺⁾ = dimensionless radial velocity, Rm>0 - V _1(T) ⁽⁺⁾ = , dimensionless transverse velocity, Rm>0 - U _2(T) ^(–) = , dimensionless radial velocity, Rm=–Rn<0, m=–n - V _2(T) ^(–) = , dimensionless transverse velocity, Rm<0 - C _m moment coefficient     

The effect of non-steady wall shear on pressure surges in conduits carrying viscous liquids

Summary A study is made of the attenuation of pressure surges in a two-dimension a channel carrying a viscous liquid when a valve at the downstream end is suddenly closed. The analysis differs from previous work in this area by taking into account the transient nature of the wall shear, which in the past has been assumed as equivalent to that existing in steady flow. For large values of the frictional resistance parameter the transient wall shear analysis results in less attenuation than given by the steady wall shear assumption.Nomenclature c /, ft/sec - e base of natural logarithms - F(x, y) integration function, equation (38) - (x) mean value of F(x, y) - g local acceleration of gravity, ft/sec² - h width of conduit, ft - k (2m–1)^{2 2} L/h ² c, equation (35) - k* 12L/h ² c, frictional resistance parameter, equation (46) - L length of conduit, ft - m positive integer - n positive integer - p pressure, lb/ft² - p ₀ constant pressure at inlet of conduit, lb/ft² - P pressure plus elevation head, p+gz, equation (4) - mean value of P over the conduit width h - P ₀ p ₀+gz ₀, lbs/ft² - R frictional resistance coefficient for steady state wall shear, lb sec/ft⁴ - s positive integer; also, condensation, equation (6) - t time, sec - t ct/L, dimensionless time - u x component of fluid velocity, ft/sec - u _m mean velocity in conduit, equation (12), ft/sec - u ₀(y) velocity profile in Poiseuille flow, equation (19), ft/sec - transformed velocity - U initial mean velocity in conduit - x distance along conduit, measured from valve (fig. 1), ft - x x/L, dimensionless distance - y distance normal to conduit wall (fig. 1), ft - y y/h, equation (25) - z elevation, measured from arbitrary datum, ft - z ₀ elevation of constant pressure source, ft - isothermal bulk compression modulus, lbs/ft² - _n , equation (37) - _n (2n–1)/2, equation (36) - viscosity, slugs/ft sec - / = kinematic viscosity, ft²/sec - density of fluid, slugs/ft³ - ₀ density of undisturbed fluid, slugs/ft³ - ø angle between conduit and vertical (fig. 1) The research upon which this paper is based was supported by a grant from the National Science Foundation.     

Development of a full-field planar Mie scattering technique for evaluating swirling mixers

A full-field planar optical diagnostic technique for studying mixing in swirling flows is described. Results were obtained using this technique to provide planar mixing information by seeding a simulated fuel stream with aluminum oxide particles, then inferring concentration from Mie scattering intensity distributions. This facility and measurement technique are unique for several reasons. First, they allow spatial variations in laser sheet energy to be corrected for on a shot-to-shot basis. Second, they allow experiments to be performed for swirlers with practical fuel and oxidizer flow rates, i.e. on the order of 150 g/s (0.33 lbm/s). Finally, they allow full size swirler models to be evaluated, with the entire exit plane imaged simultaneously. Representative results are presented as false color images of the planar mixing fields. These images allow rapid assessment of the mixing process and its changes with variations in operating conditions or swirler geometry.List of Symbols C seed particle concentration, m^–3 - mean component of seed particle concentration, m^–3 - C fluctuating component of seed particle concentration, m^–3 - C ^* time averaged ratio of rms particle concentration fluctuations to average particle concentration, dimensionless - d _p particle diameter, m - I laser energy after passing through the flow, J/m² - mean laser energy, J/m² - I ₀ laser energy before passing through the flow, J/m² - L _v eddy length scale, m - l laser beam path length, m - U _v eddy velocity scale, m/s - V diode voltage reading after passing through the flow, V - mean diode voltage, V - V ₀ diode voltage reading before passing through the flow, V - absorptivity, m² - _rel relative equivalence ratio, dimensionless - fluid viscosity, Ns - _p particle density, kg/m³ - Stokes number= _p / _f , dimensionless - _f flow time scale, s - _p particle response time, s     

Mixed convection on vertical plate for fluids of any prandtl number

A mixed convection parameter=(Ra) ^1/4/(Re)^1/2, with=Pr/(1+Pr) and=Pr/(1 +Pr)^1/2, is proposed to replace the conventional Richardson number, Gr/Re², for combined forced and free convection flow on an isothermal vertical plate. This parameter can readily be reduced to the controlling parameters for the relative importance of the forced and the free convection,Ra ^1/4/(Re ^1/2 Pr ^1/3) forPr 1, and (RaPr)^1/2/(RePr ^1/2 forPr 1. Furthermore, new coordinates and dependent variables are properly defined in terms of, so that the transformed nonsimilar boundary-layer equations give numerical solutions that are uniformly valid over the entire range of mixed convection intensity from forced convection limit to free convection limit for fluids of any Prandtl number from 0.001 to 10,000. The effects of mixed convection intensity and the Prandtl number on the velocity profiles, the temperature profiles, the wall friction, and the heat transfer rate are illustrated for both cases of buoyancy assisting and opposing flow conditions.

---

Mischkonvektion an einer vertikalen Platte für Fluide beliebiger Prandtl-Zahl

Zusammenfassung Für die kombinierte Zwangs- und freie Konvektion an einer isothermen senkrechten Platte wird ein Mischkonvektions-Parameter=( Ra) ^1/4 (Re)^1/2, mit=Pr/(1 +Pr) und=Pr/(1 +Pr)^1/2 vorgeschlagen, den die gebräuchliche Richardson-Zahl, Gr/Re², ersetzen soll. Dieser Parameter kann ohne weiteres auf die maßgebenden Kennzahlen für den relativen Einfluß der erzwungenen und der freien Konvektion reduziert werden,Ra ^1/4/(Re ^1/2 Pr ^1/3) fürPr 1 und (RaPr)^1/4/(RePr)^1/2 fürPr 1. Weiterhin werden neue Koordinaten und abhängige Variablen als Funktion von definiert, so daß für die transformierten Grenzschichtgleichungen numerische Lösungen erstellt werden können, die über den gesamten Bereich der Mischkonvektion, von der freien Konvektion bis zur Zwangskonvektion, für Fluide jeglicher Prandtl-Zahl von 0.001 bis 10.000 gleichmäßig gültig sind. Der Einfluß der Intensität der Mischkonvektion und der Prandtl-Zahl auf die Geschwindigkeitsprofile, die Temperaturprofile, die Wandreibung und den Wärmeübergangskoeffizienten werden für die beiden Fälle der Strömung in und entgegengesetzt zur Schwerkraftrichtung dargestellt.

---

Nomenclature C _f local friction coefficient - C _p specific heat capacity - f reduced stream function - g gravitational acceleration - Gr local Grashoff number,g T _w –T )x³/v² - Nu local Nusselt number - Pr Prandtl number,v/ - Ra local Rayleigh number,g T _w –T x ³/( v) - Re local Reynolds number,u x/v - Ri Richardson number,Gr/Re ² - T fluid temperature - T _w wall temperature - T free stream temperature - u velocity component in thex direction - u free stream velocity - v velocity component in they direction - x vertical coordinate measuring from the leading edge - y horizontal coordinate Greek symbols thermal diffusivity - thermal expansion coefficient - mixed convection parameter (Ra)1/4/Re)^1/2 - pseudo-similarity variable,(y/x) - ₀ conventional similarity variable,(y/x)Re ^1/2 - dimensionless temperature, (T–T T _W –T - unified mixed-flow parameter, [(Re) ^1/2 + (Ra)^1/4] - dynamic viscosity - kinematic viscosity - stretched streamwise coordinate or mixed convection parameter, [1 + (Re)^1/2/(Ra) ^1/4]^–1=/(1 +) - density - Pr/(1 + Pr) _w wall shear stress - stream function - Pr/(l+Pr)^1/3 This research was supported by a grand from the National Science Council of ROC     

The virtual origin of riblets in an open channel flow

In this paper, a method using the mean velocity profiles for the buffer layer was developed for the estimation of the virtual origin over a riblets surface in an open channel flow. First, the standardized profiles of the mixing length were estimated from the velocity measurement in the inner layer, and the location of the edge of the viscous layer was obtained. Then, the virtual origins were estimated by the best match between the measured velocity profile and the equations of the velocity profile derived from the mixing length profiles. It was made clear that the virtual origin and the thickness of the viscous layer are the function of the roughness Reynolds number. The drag variation coincided well with other results.Nomenclature f _r skin friction coefficient - f _ro skin friction coefficient in smooth channel at the same flow quantity and the same energy slope - g gravity acceleration - H water depth from virtual origin to water surface - H ⁺ u*H/ - H false water depth from top of riblets to water surface - H ⁺ u*H/ - I _e streamwise energy slope - I _b bed slope - k riblet height - k ⁺ u*k/ - l mixing length - l _s standardized mixing length - Q flow quantity - Re Reynolds number volume flow/unit width/v - s riblet spacing - u mean velocity - u* friction velocity = - u* false friction velocity = - y distance from virtual origin - y distance from top of riblet - y ₀ distance from top of riblet to virtual origin - y _v distance from top of riblet to edge of viscous layer - y ⁺ u*y/ - y ⁺ u*y/ - y ₀ ⁺ u*y ₀/ - u ⁺ u*y/ - shifting coefficient for standardization - thickness of viscous layer=y ₀+y - ⁺ u*/ - ⁺ u*/ - eddy viscosity - ridge angle - v kinematic viscosity - density - shear stress     

Injection moulding of thermoplastics: Freezing of variable-viscosity fluids.

The injection moulding of thermoplastics involves, during mould filling, flows of hot polymer melts into mould networks, the walls of which are so cold that frozen layers form on them. An analytical study of such flows is presented here for the case when the Graetz and Nahme numbers are large and the Pearson number is small. Thus the flows are developing and temperature differences due to heat generation by viscous dissipation are sufficiently large to cause significant variations in viscosity (but the difference between the entry temperature of the polymer to a specific part of the mould network and the melting temperature of the polymer is not). Br Brinkman number - Gz Graetz number - h half-height of channel or disc - h ^* half-height of polymer melt region in channel or disc - L length of channel or pipe - m viscosity shear-rate exponent - Na Nahme number - p pressure - P pressure drop - Pe Péclet number - Pn Pearson number - Q volumetric flowrate - r radial coordinate in pipe or disc - R radius of pipe - Re Reynolds number - R _i inner radius of disc - R _o outer radius of disc - R ^* radius of polymer melt region in pipe - T temperature - T _ad adiabatic temperature rise - T _e entry polymer melt temperature - T _m melting temperature of polymer - T _max maximum temperature - T ₀ reference temperature - T _w wall temperature - flow-average temperature rise - u _r radial velocity in pipe or disc - u _x axial velocity in channel - u _y transverse velocity in channel or disc - u _z axial velocity in pipe - w width of channel - x axial coordinate in channel or modified radial coordinate in disc - y transverse coordinate in channel or disc - z axial coordinate in pipe - thermal conductivity of molten polymer - thermal conductivity of frozen polymer - scaled dimensionless axial coordinate in channel or pipe or radial coordinate in disc - ₀ undetermined integration constant - heat capacity of molten polymer - viscosity temperature exponent - dimensionless transverse coordinate in channel or disc - ^* dimensionless half-height of polymer melt region in channel or disc - H ^* scaled dimensionless half-height of polymer melt region in channel or disc or radius of polymer melt region in pipe - dimensionless temperature - ^* dimensionless wall temperature - scaled dimensionless temperature - numerical constant - µ viscosity of molten polymer - µ ₀ consistency of molten polymer - dimensionless pressure gradient - scaled dimensionless pressure gradient - density of molten polymer - dimensionless radial coordinate in pipe or disc - _i dimensionless inner radius of disc - ^* dimensionless radius of polymer melt region in pipe - dimensionless streamfunction - scaled dimensionless streamfunction - dummy variable - streamfunction - similarity variable - similarity variable     

Rheological properties of reactive polymer melts.

A new method for describing the rheological properties of reactive polymer melts, which was presented in an earlier paper, is developed in more detail. In particular, a detailed derivation of the equation of a first-order rheometrical flow surface is given and a procedure for determining parameters and functions occurring in this equation is proposed. The experimental verification of the presented approach was carried out using our data for polyamide-6.Notation E Dimensionless reduced viscosity, eq. (34) - E ₀ Newtonian asymptote of the function (36) - E power-law asymptote of the function (36) - E _{= 1} the value ofE at = 1 - k degradation reaction rate constant, s^–1 - k ₁ rate constant of function (t), eq. (26), s^–1 - k ₂ rate constant of function (t), eq. (29), s^–1 - K(t) residence-time-dependent consistency factor, eq. (22) - M _w weight-average molecular weight - M _x x-th moment of the molecular weight distribution - R gas constant - S _x M _x /M _w - t residence time in molten state, s - t _j thej-th value oft, s - T temperature, K - % MathType!MTEF!2!1!+-% feaafiart1ev1aaatCvAUfeBSjuyZL2yd9gzLbvyNv2CaerbuLwBLn% hiov2DGi1BTfMBaeXatLxBI9gBaerbd9wDYLwzYbItLDharqqtubsr% 4rNCHbGeaGqiVu0Je9sqqrpepC0xbbL8F4rqqrFfpeea0xd9vqpe0x% c9q8qqaqFn0dXdir-xcvk9pIe9q8qqaq-xir-f0-yqaqVeLsFr0-vr% 0-vr0db8meaabaqaciGacaGaaeqabaWaaeaaeaaakeaaieGaceWFZo% Gbaiaaaaa!3B4E!\[\dot \gamma \] shear rate, s^–1 - _i thei-th value of , s^–1 - _r =1 the value of at = 1, s^–1 - ^* reduced shear rate, eq. (44), s^–1 - dimensionless reduced shear rate, eq. (35) - viscosity, Pa · s - shear-rate and residence-time dependent viscosity, Pa · s - zero-shear-rate degradation curve - degradation curve at - _{t0 (t)} zero-residence-time flow curve - Newtonian asymptote of the RFS - instantaneous flow curve - power-law asymptote of the RFS - _0,0 zero-shear-rate and zero-residence-time viscosity, Pa · s - _E=1 value of viscosity atE=1, Pa · s - ^* reduced viscosity, eq. (43), Pa · s - zero-residence-time rheological time constant, s - density, kg/m³ - (t),(t) residence time functions     

Performance prediction of dual cylindrical wave laser devices for flow measurements

The dual cylindrical wave system is a variant of laser Doppler velocimetry, in which two cylindrical waves of laser light are used to illuminate a moving particle. This instrument is being used for local measurement of the unsteady skin friction in turbulent boundary layers, as well as droplet sizing in spray flows. In the present work, performance of these new devices is examined using the electromagnetic theory of light. Various requirements for the design and operation of these instruments have been further elaborated and extended. The accuracy of the previous experimental results has also been considered. The optics-related errors are shown to be negligible in the measurements of streamwise as well as spanwise wall velocity gradients. However, rigorous simulations appear to be essential for proper calibration of the particle sizing device.List of symbols A, B, C three particle positions - a half-width of an optical slit - a _gm amplitude of a plane wave in the spectrum of a cylindrical wave - d _f fringe spacing - d _p particle diameter - E amplitude of the electric oscillation in the optical field - E _c combined electric field of two cylindrical waves - E _o maximum strength of the electric field at the source of a cylindrical wave - E _s electric field of a scattered wave - E _y time-dependent electric field in the case of electric polarization - f characteristic length for the phase of the scattering amplitude - f _a anisotropic frequency - f _D Doppler frequency - F _DCW transfer function of DCW system for particle sizing - F _pDA Phase Doppler transfer function - g wall velocity gradient - g _m measured wall velocity gradient - I ₀, I₂ integrals in the asymptotic expansion of the scattering amplitude - I _s intensity of the scattered light - k wave number of laser light in the fluid medium - m refractive index of the particle relative to the surrounding medium - N ₀ nominal number of fringes resulting from interference of two cylindrical waves - P phase of a plane wave - P ₁, P₂ phases of plane waves from downstream and upstream cylindrical waves respectively - P _s scattered light power at a receiving aperture - r unit vector in the direction of light scattering - r _D distance of the signal detector from the particle center - S scattering amplitude of a cylindrical wave - S ₁, S₂ Scattering amplitudes of the cylindrical waves emanating from S₁ and S₂ respectively - magnitude of the scattering amplitude for a plane wave - S _c combined scattering amplitude of two cylindrical waves - S₁, S₂ downstream and upstream sources of cylindrical waves, respectively - S scattering amplitude of a plane wave - s half-spacing between sources of the cylindrical waves - t time - u velocity along x-axis - w ₀ 1/e half-width of the field distribution at the waist of a laser sheet - X ₀ nominal width of the fringe volume along the particle path - X particle position in the measuring volume - x, y, z Cartesian coordinates Greek symbols angle of the direction of wave propagation from x-axis - coefficient of the second-order term in the phase function of a cylindrical wave - angular size of the signal receiving aperture - incremental used for numerical differentiation the ratio of to _p - — ₀ integration parameter for I₀ and I₂ - half-angle between the directions of propagation of two waves - wavelength of laser in the fluid medium - ₀ wavelength of laser in vacuum - parameter defining the direction of propagation of a plane wave - 1/e 1/e half-width of the function A - ₀ direction of propagation of the dominant plane wave in the spectrum - _0s the direction of propagation of the plane wave that contributes predominantly to scattering in a particular direction - _p the value of . corresponding to one cycle of P - _s change in corresponding to a lobe of the scattering amplitude - a dimensional form of that determines lobes in the scattered field - signal phase, ₀ + _a - _a anisotropic phase shift - ₀ phase difference between two indicent waves - off-axis angle - elevation angle - circular frequency of laser light     

A three-parameter model describing the experimental relation between shear stress and shear rate for laminar flow of aqueous polymer solutions

Summary A three-parameter model is introduced to describe the shear rate — shear stress relation for dilute aqueous solutions of polyacrylamide (Separan AP-30) or polyethylenoxide (Polyox WSR-301) in the concentration range 50 wppm – 10,000 wppm. Solutions of both polymers show for a similar rheological behaviour. This behaviour can be described by an equation having three parameters i.e. zero-shear viscosity ₀, infinite-shear viscosity , and yield stress ₀, each depending on the polymer concentration. A good agreement is found between the values calculated with this three-parameter model and the experimental results obtained with a cone-and-plate rheogoniometer and those determined with a capillary-tube rheometer.

---

Zusammenfassung Der Zusammenhang zwischen Schubspannung und Schergeschwindigkeit von strukturviskosen Flüssigkeiten wird durch ein Modell mit drei Parametern beschrieben. Mit verdünnten wäßrigen Polyacrylamid-(Separan AP-30) sowie Polyäthylenoxidlösungen (Polyox WSR-301) wird das Modell experimentell geprüft. Beide Polymerlösungen zeigen im untersuchten Schergeschwindigkeitsbereich von ein ähnliches rheologisches Verhalten. Dieses Verhalten kann mit drei konzentrationsabhängigen Größen, nämlich einer Null-Viskosität ₀, einer Grenz-Viskosität und einer Fließgrenze ₀ beschrieben werden. Die Ergebnisse von Experimenten mit einem Kegel-Platte-Rheogoniometer sowie einem Kapillarviskosimeter sind in guter Übereinstimmung mit den Werten, die mit dem Drei-Parameter-Modell berechnet worden sind.

---

a Pa^–1 physical quantity defined by:a = {1 – ( / ₀)}/ ₀ - c l concentration (wppm) - D m capillary diameter - L m length of capillary tube - P Pa pressure drop - R m radius of capillary tube - u m s^–1 average velocity - v _r m s^–1 local axial velocity at a distancer from the axis of the tube - shear rate (–dv _r /dr) - local shear rate in capillary flow - s^–1 wall shear rate in capillary flow - Pa s dynamic viscosity - _a Pa s apparent viscosity defined by eq. [2] - ( _a ) Pa s apparent viscosity in capillary tube at a distanceR from the axis - ₀ Pa s zero-shear viscosity defined by eq. [4] - Pa s infinite-shear viscosity defined by eq. [5] - l ratior/R - kg m^– density - Pa shear stress - ₀ Pa yield stress - _r Pa local shear stress in capillary flow - _R Pa wall shear stress in capillary flow _R = (PR/2L) - _v m³ s^–1 volume rate of flow With 8 figures and 1 table