Buoyancy and cross flow effects on heat transfer of multiple impinging slot air jets cooling a flat plate at different orientations

The present article reports on heat transfer characteristics associated with multiple laminar impinging air jet cooling a hot flat plat at different orientations. The work aims to study the interactions of the effects of cross flow, buoyancy induced flow, orientation of the hot surface with respect to gravity, Reynolds numbers and Rayleigh numbers on heat transfer characteristics. Experiments have been carried out for different values of jet Reynolds number, Rayleigh number and cross flow strength and at different orientations of the air jet with respect to the target hot plate. In general, the effective cooling of the plate has been observed to be increased with increasing Reynolds number and Rayleigh number. The results concluded that the hot surface orientation is important for optimum performance in practical applications. It was found that for Re ≥ 400 and Ra ≥ 10,000 (these ranges give 0.0142 ≤ Ri ≤ 1.59 the Nusselt number is independent on the hot surface orientation. However, for Re ≤ 300 and Ra ≥ 100,000 (these ranges give 1.59 ≤ Ri ≤ 42.85): (i) the Nusselt number for horizontal orientation with hot surface facing down is less that that of vertical orientation and that of horizontal orientation with hot surface facing up, and (ii) the Nusselt number of vertical orientation is approximately the same as that of horizontal orientation with hot surface facing up. For all surfaces orientations and for the entire ranges of Re and Ra, it was found that increasing the cross flow strength decreases the effective cooling of the surface.     

An experimental investigation of moderate reynolds number flow in a T-Channel

An experimental investigation of water flow in a T-shaped channel with rectangular cross section (20 × 20 mm inlet ID and 20 × 40 mm outlet ID) has been conducted for a Reynolds number Re range of 56–422, based on inlet diameter. Dynamical conditions and the T-channel geometry of the current study are applicable to the microscale. 2-D planar particle imaging velocimetry (PIV) and laser-induced fluorescence (LIF) were used in multiple locations of the T-channel to investigate local dynamical behaviors. Steady symmetric and asymmetric flow regimes predicted in the literature, which is largely numerical, are experimentally verified. Unsteady flow regimes, which are numerically predicted to occur at higher Re but have not yet been experimentally characterized, are also examined, and real-time LIF results illuminate the evolution of unsteady structure. Experimental data of the present resolution and scope are not presently available for unsteady flow regimes. Time scales are presented for unsteady flow regimes, which are found to exhibit periodic behavior and to occur for Re  ≥ 195. An unsteady symmetrical regime is identified for Re ≥ 350 that is detrimental to mixing. Momentum fields and dynamical behaviors of all flow regimes are characterized in detail, such that published mixing trends may be better understood. Results of all experimental trials were used to construct a regime map. A symmetric topology is found to be dominant for Re from 56 to 116, when flow is steady, and 350 to 422, when flow is characterized by unsteady stagnation-point oscillation in the T-channel junction. Asymmetric flow, which is positively indicated for mixing, is dominant for Re between 142 and 298, and the fluid interface exhibits both steady (two standing vortices) and unsteady (shear-layer type roll-up) behaviors. This result is based on multiple experiments and suggests a practical operating range of 142  ≤ Re ≤ 298 where asymmetric flow is highly likely to experimentally occur. The identification of an upper limit on Re,  beyond which mixing appears negatively impacted by a more symmetrical momentum field, is practically important as pressure drops on the microscale are significant.     

Secondary flow patterns and mixing in laminar pulsating flow through a curved pipe

Mixing by secondary flow is studied by particle image velocimetry (PIV) in a developing laminar pulsating flow through a circular curved pipe. The pipe curvature ratio is η = r ₀/r _c  = 0.09, and the curvature angle is 90°. Different secondary flow patterns are formed during an oscillation period due to competition among the centrifugal, inertial, and viscous forces. These different secondary-flow structures lead to different transverse-mixing schemes in the flow. Here, transverse mixing enhancement is investigated by imposing different pulsating conditions (Dean number, velocity ratio, and frequency parameter); favorable pulsating conditions for mixing are introduced. To obviate light-refraction effects during PIV measurements, a T-shaped structure is installed downstream of the curved pipe. Experiments are carried out for the Reynolds numbers range 420 ≤ Re_st ≤ 1,000 (Dean numbers 126.6 ≤ Dn ≤ 301.5) corresponding to non-oscillating flow, velocity component ratios 1 ≤ (β = U _max,osc/U _m,st) ≤ 4 (the ratio of velocity amplitude of oscillations to the mean velocity without oscillations), and frequency parameters 8.37 < (α = r ₀(ω/ν)^0.5) < 24.5, where α² is the ratio of viscous diffusion time over the pipe radius to the characteristic oscillation time. The variations in cross-sectional average values of absolute axial vorticity (|ζ|) and transverse strain rate (|ε|) are analyzed in order to quantify mixing. The effects of each parameter (Re_st, β, and α) on transverse mixing are discussed by comparing the dimensionless vorticities (|ζ _P |/|ζ _S |) and dimensionless transverse strain rates (|ε _P |/|ε _S |) during a complete oscillation period.     

Numerical study of buoyancy- and thermocapillary-driven flows in a cavity

Thermocapillary- and buoyancy-driven convection in open cavities with differentially heated endwalls is investigated by numerical solutions of the two-dimensional Navier-Stokes equations coupled with the energy equation. We studied the thermocapillary and buoyancy convection in the cavities, filled with low-Prandtl-number fluids, with two aspect-ratiosA=1 and 4, Grashof number up to 10⁵ and Reynolds number ⋎Re⋎≤10⁴. Our results show that thermocapillary can have a quite significant effect on the stability of a primarily buoyancy-driven flow, as well as on the flow structures and dynamic behavior for both additive effect (i.e., positiveRe) and opposing effect (i.e., negativeRe).     

Experimental study on surface wave and film breakdown of falling liquid film flow

In order to evaluate characteristics of the liquid film flow and their influences on heat and mass transfer, measurements of the instantaneous film thickness using a capacitance method and observation of film breakdown are performed. Experimental results are reported in the paper. Experiments are carried out at Re = 250–10000, T _in = 20–50°C and three axial positions of vertically falling liquid films for film thickness measurements. Instantaneous surface waveshapes are given by the interpretation of the test data using the cubic spline method. The correlation of the mean film thickness versus the film Reynolds number is also given by fitting the test data. It is revealed that the surface wave has nonlinear behavior. Observation of film breakdown is performed at Re = 1.40 × 10³–1.75 × 10⁴ and T _in = 85–95°C. From experimental results, the correlation of the film breakdown criterion can be obtained as follows: Bd = 1.567 × 10⁻⁶ Re ^1.183     

Comparison of turbulent channel and pipe flows with varying Reynolds number

Single normal hot-wire measurements of the streamwise component of velocity were taken in fully developed turbulent channel and pipe flows for matched friction Reynolds numbers ranging from 1,000 ≤ Re _τ ≤ 3,000. A total of 27 velocity profile measurements were taken with a systematic variation in the inner-scaled hot-wire sensor length l ⁺ and the hot-wire length-to-diameter ratio (l/d). It was observed that for constant l ⁺ = 22 and l/d >~200l/d \gtrsim 200, the near-wall peak in turbulence intensity rises with Reynolds number in both channels and pipes. This is in contrast to Hultmark et al. in J Fluid Mech 649:103–113, (2010), who report no growth in the near-wall peak turbulence intensity for pipe flow with l ⁺ = 20. Further, it was found that channel and pipe flows have very similar streamwise velocity statistics and energy spectra over this range of Reynolds numbers, with the only difference observed in the outer region of the mean velocity profile. Measurements where l ⁺ and l/d were systematically varied reveal that l ⁺ effects are akin to spatial filtering and that increasing sensor size will lead to attenuation of an increasingly large range of small scales. In contrast, when l/d was insufficient, the measured energy is attenuated over a very broad range of scales. These findings are in agreement with similar studies in boundary layer flows and highlight the need to carefully consider sensor and anemometry parameters when comparing flows across different geometries and when drawing conclusions regarding the Reynolds number dependency of measured turbulence statistics. With an emphasis on accuracy, measurement resolution and wall proximity, these measurements are taken at comparable Reynolds numbers to currently available DNS data sets of turbulent channel/pipe flows and are intended to serve as a database for comparison between physical and numerical experiments.     

On the Reynolds number scaling of vorticity production at no-slip walls during vortex-wall collisions

Recently, numerical studies revealed two different scaling regimes of the peak enstrophy Z and palinstrophy P during the collision of a dipole with a no-slip wall [Clercx and van Heijst, Phys. Rev. E 65, 066305, 2002]: Z μ Re^0.8{Z\propto{\rm Re}^{0.8}} and P μ Re^2.25{P\propto {\rm Re}^{2.25}} for 5 × 10² ≤ Re ≤ 2 × 10⁴ and Z μ Re^0.5{Z\propto{\rm Re}^{0.5}} and P μ Re^1.5{P\propto{\rm Re}^{1.5}} for Re ≥ 2 × 10⁴ (with Re based on the velocity and size of the dipole). A critical Reynolds number Re _c (here, Re_c ? 2×10⁴{{\rm Re}_c\approx 2\times 10^4}) is identified below which the interaction time of the dipole with the boundary layer depends on the kinematic viscosity ν. The oscillating plate as a boundary-layer problem can then be used to mimick the vortex-wall interaction and the following scaling relations are obtained: Z μ Re^3/4, P μ Re^9/4{Z\propto{\rm Re}^{3/4}, P\propto {\rm Re}^{9/4}} , and dP/dt μ Re^11/4{\propto {\rm Re}^{11/4}} in agreement with the numerically obtained scaling laws. For Re ≥ Re _c the interaction time of the dipole with the boundary layer becomes independent of the kinematic viscosity and, applying flat-plate boundary-layer theory, this yields: Z μ Re^1/2{Z\propto{\rm Re}^{1/2}} and P μ Re^3/2{P\propto {\rm Re}^{3/2}}.     

Inertial-microfluidic radial migration in solid/liquid two-phase flow through a microcapillary: Particle equilibrium position

Although equilibrium of spherical particles under radial migration has been extensively investigated, mostly in macroscale flows with characteristic lengths on the order of centimeters, it is not fully characterized at relatively small Reynolds numbers, 1 ≤ Re ≤ 100. This paper experimentally studies “inertial microfluidic” radial migration of spherical particles in circular Poiseuille flow through a microcapillary. Microparticle tracking experiments are performed to obtain the spatial distribution of the particles by adopting a depth-resolved measurement technique. Through the analysis of the radial distribution of particles, inertial microfluidic circular Poiseuille flow is shown to induce a strong radial migration of particles at substantially small Re, which is quite in contrast to the pipe flows at large Re previously reported. This particle migration phenomenon is so prominent that particle equilibrium positions are formed even at small Re. However, it turns out that there exists a certain critical Re below which particle equilibrium position is almost fixed, but above which it seems to drift toward the channel wall.     

A note on wind-tunnel turbulence measurements with DPIV

At moderate Reynolds numbers (10⁴ ≤ Re ≤ 10⁵), the performance of lifting surfaces is strongly affected by the potential for laminar boundary layer separation and subsequent reattachment and the use of high-quality, low-turbulence wind tunnels is essential in characterising flight at comparatively small scales (where the wing chord may be from 1 to 5 cm in length) and low speeds (on the order of 10 m/s). Measurement of the existing turbulence levels in such facilities is hard and has not been achieved using DPIV methods due to the relatively small bandwidth of measurable velocities. A series of experiments is reported here where DPIV sampling parameters are driven beyond their normal range in an attempt to measure turbulence levels in a low turbulence wind tunnel. The results show that DPIV can measure the background turbulence, and therefore its instantaneous structure. The measurements also reveal certain challenges in investigating the aerodynamic performance of small-scale flying devices.     

Characterization of fluid flow patterns and heat transfer in horizontal channel mixed convection

Two mechanisms of roll initiation are highlighted in a horizontal channel flow, uniformly heated from below, at constant heat flux (Γ = 10, Pr = 7, 50 ≤ Re ≤ 100, 0 ≤ Ra ≤ 10⁶). The first mechanism is the classical one, it occurs for low Rayleigh numbers and is initiated by the lateral wall effect. The second occurs for higher Rayleigh numbers and combines the previous effect with a supercritical vertical temperature gradient in the lower boundary layer, which simultaneously triggers pairs of rolls in the whole zone in between the two lateral rolls. We have found that in the present configuration, the transition between the two roll initiation mechanisms occurs for Ra/Re ² ≈ 18. Consequently, the heat transfer is significantly enhanced compared to the pure forced convection case owing to the flow pattern responsible of the continuous flooding the heated wall with cold fluid.     

Breakdown of the Reynolds Analogy in a Stagnation Region Under Inflow Disturbances

A systematic analysis is performed for the Reynolds analogy breakdown at stagnation-region flow and heat transfer in the presence of inflow disturbances. The Reynolds analogy breakdown between momentum and energy transfers in a stagnation region is scrutinized by varying the Reynolds number (5000≤Re≤20000), the amplitude (0.00075≤A≤0.003) and the length scale (λ/δ=10.6). A spanwise sinusoidal variation is superimposed on the velocity component normal to the wall. Self-similarity solutions are obtained with trigonometric series expansions. The Reynolds analogy criterion demonstrates that the rate of change of skin friction is different from that of wall heat transfer. Different evolutions of the rates of skin friction and wall heat transfer are due to the difference between 〈s'v'〉 and 〈v'T'〉. An in-depth analysis on 〈s'v'〉 and 〈 v'T'〉 is performed by analysis using disturbance correlations based on the fluctuating velocity transport equations in vorticity form. It is found that the pressure fluctuations, the wall blocking and the Lamb vectors are responsible for the breakdown of the Reynolds analogy. A direct comparison is made between momentum and energy balances associated with the three responsible mechanisms. A common finding is that their profiles are changed significantly at a location where the evolution of the streamwise vortex is strong. Received 12 May 2000 and accepted 6 March 2001     

Unsteady PTV velocity field past an airfoil solved with DNS: Part 2. Validation and application at Reynolds numbers up to <Emphasis Type="Italic">Re</Emphasis> ≤ 10<Superscript>4</Superscript>

Hybrid unsteady-flow simulation combining particle tracking velocimetry (PTV) and direct numerical simulation (DNS) is introduced in the series of two papers. Particle velocities on a laser-light sheet acquired with time-resolved PTV in a water tunnel are supplied to two-dimensional DNS with time intervals corresponding to the frame rate of the PTV. Hybrid velocity fields then approach those representing the PTV data in the course of time, and the reconstructed velocity fields satisfy the governing equations with the resolution comparable to numerical simulation. In part 2, by extending the capabilities of the hybrid simulation to higher Reynolds numbers, we simulate flows past the NACA0012 airfoil over ranges of Reynolds numbers (Re ≤ 10⁴) and angles of attack (−5° ≤ α ≤ 20°) and validate the proposed technique by comparing with experimental results in terms of the lift and drag coefficients. We also compare the results with unsteady Reynolds-averaged Navier–Stokes (URANS) simulation in two-dimensions and show the advantages of the hybrid simulation against two-dimensional URANS.     

Reynolds Number Effects on the Coherent Dynamics of the Turbulent Horseshoe Vortex System

The adverse pressure gradient induced by a surface-mounted obstacle in a turbulent boundary layer causes the approaching flow to separate and form a dynamically rich horseshoe vortex system (HSV) in the junction of the obstacle with the wall. The Reynolds number of the flow (Re) is one of the important parameters that control the rich coherent dynamics of the vortex, which are known to give rise to low-frequency, bimodal fluctuations of the velocity field (Devenport and Simpson, J Fluid Mech 210:23–55, 1990; Paik et al., Phys Fluids 19:045107, 2007). We carry out detached eddy simulations (DES) of the flow past a circular cylinder mounted on a rectangular channel for Re = 2.0 × 10⁴ and 3.9 × 10⁴ (Dargahi, Exp Fluids 8:1–12, 1989) in order to systematically investigate the effect of the Reynolds number on the HSV dynamics. The computed results are compared with each other and with previous experimental and computational results for a related junction flow at a much higher Reynolds number (Re = 1.15 × 10⁵) (Devenport and Simpson, J Fluid Mech 210:23–55, 1990; Paik et al., Phys Fluids 19:045107, 2007). The computed results reveal significant variations with Re in terms of the mean-flow quantities, turbulence statistics, and the coherent dynamics of the turbulent HSV. For Re = 2.0 × 10⁴ the HSV system consists of a large number of necklace-type vortices that are shed periodically at higher frequencies than those observed in the Re = 3.9 × 10⁴ case. For this latter case the number of large-scale vortical structures that comprise the instantaneous HSV system is reduced significantly and the flow dynamics becomes quasi-periodic. For both cases, we show that the instantaneous flowfields are dominated by eruptions of wall-generated vorticity associated with the growth of hairpin vortices that wrap around and disorganize the primary HSV system. The intensity and frequency of these eruptions, however, appears to diminish rapidly with decreasing Re. In the high Re case the HSV system consists of a single, highly energetic, large-scale necklace vortex that is aperiodically disorganized by the growth of the hairpin mode. Regardless of the Re, we find pockets in the junction region within which the histograms of velocity fluctuations are bimodal as has also been observed in several previous experimental studies.     

Forced convection flow over a microsphere

Forced convection heat transfer characteristics around a microsphere subjected to uniform heat flux boundary condition is numerically investigated in this study. Moderate to high values of Reynolds number and a wide range of Prandtl number are considered. The analysis assumes that the continuity assumption is valid and hence the Navier–Stokes equations are solved for the range of Knudsen number of 0.001 ≤ Kn ≤ 0.1. The appropriate boundary conditions at the surface of the microsphere; the velocity slip and temperature jump are applied. The effect of the flow parameters: Re, Pr and Kn on the velocity and temperature distribution is presented and hence a better control on the boundary layer thickness can be achieved in the microscale level. Furthermore, the effect of the controlling parameters on the delay of flow separation, reduced shear stress, drag coefficient and on the Nusselt number profiles is also presented in the results.     

The ultra-low Reynolds number airfoil wake

Lift force and the near wake of an NACA 0012 airfoil were measured over the angle (α) of attack of 0°–90° and the chord Reynolds number (Re _c ), 5.3 × 10³–5.1 × 10⁴, with a view to understand thoroughly the near wake of the airfoil at low- to ultra-low Re _c . While the lift force is measured using a load cell, the detailed flow structure is captured using laser-Doppler anemometry, particle image velocimetry, and laser-induced fluorescence flow visualization. It has been found that the stall of an airfoil, characterized by a drop in the lift force, occurs at Re _c  ≥ 1.05 × 10⁴ but is absent at Re _c  = 5.3 × 10³. The observation is connected to the presence of the separation bubble at high Re _c but absence of the bubble at ultra-low Re _c , as evidenced in our wake measurements. The near-wake characteristics are examined and discussed in detail, including the vortex formation length, wake width, spanwise vorticity, wake bubble size, wavelength of K–H vortices, Strouhal numbers, and their dependence on α and Re _c .     

A numerical study of the steady forced convection heat transfer from an unconfined circular cylinder

Forced convection heat transfer from an unconfined circular cylinder in the steady cross-flow regime has been studied using a finite volume method (FVM) implemented on a Cartesian grid system in the range as 10 ≤ Re ≤ 45 and 0.7 ≤ Pr ≤ 400. The numerical results are used to develop simple correlations for Nusselt number as a function of the pertinent dimensionless variables. In addition to average Nusselt number, the effects of Re, Pr and thermal boundary conditions on the temperature field near the cylinder and on the local Nusselt number distributions have also been presented to provide further physical insights into the nature of the flow. The rate of heat transfer increases with an increase in the Reynolds and/or Prandtl numbers. The uniform heat flux condition always shows higher value of heat transfer coefficient than the constant wall temperature at the surface of the cylinder for the same Reynolds and Prandtl numbers. The maximum difference between the two values is around 15–20%.     

Large eddy simulation of compressible channel flow

Astract The present study is a contribution to the analysis of wall-bounded compressible flows, including a special focus on wall modeling for compressible turbulent boundary layer in a plane channel. large eddy simulation (LES) of fully developed isothermal channel flows at Re = 3,000 and Re = 4,880 with a sufficient mesh refinement at the wall are carried out in the Mach number range 0.3 ≤ M ≤ 3 for two different source term formulations: first the classical extension of the incompressible configuration by Coleman et al. (J. Fluid Mech. 305:159–183, 1995), second a formulation presently derived to model both streamwise pressure drop and streamwise internal energy loss in a spatially developed compressible channel flow. It is shown that the second formulation is consistent with the spatial problem and yields a much stronger cooling effect at the wall than the classical formulation. Based on the present LES data bank, compressibility and low Reynolds number effects are analysed in terms of coherent structure and statistics. A study of the universality of the structure of the turbulence in non-hypersonic compressible boundary layers (M≤5) is performed in reference to Bradshaw (Annu. Rev. Fluid. Mech. 9:33–54, 1977). An improvement of the van Driest transformation is proposed; it accounts for both density and viscosity changes in the wall layer. Consistently, a new integral wall scaling (y ^c+) which accounts for strong temperature gradients at the wall is developed for the present non-adiabatic compressible flow. The modification of the strong Reynolds analogy proposed by Huang et al. (J. Fluid Mech. 305:185–218, 1995) to model the correlation between velocity and temperature for non-adiabatic wall layers is assessed on the basis of a Crocco–Busemann relation specific to channel flow. The key role of the mixing turbulent Prandtl number Pr _m is pointed out. Results show very good agreement for both source formulations although each of them involve a very different amount of energy transfer at the wall. The present work was performed within the framework of the French–German research initiative “large eddy simulation of complex flows’ (UR 507). The computing resources were provided by IDRIS-France. The authors gratefully acknowledge the financial support from the Centre National de la Recherche Scientifique (CNRS), the Centre d’été Mathématique de Recherche Avancée en Calcul Scientifique (CEMRACS) and the Direction Générale de l’Armement (DGA/D4S).     

Numerical simulation of fluid flow and heat transfer characteristics in channel with V corrugated plates

A detailed numerical study is carried out to investigate fluid flow and heat transfer characteristics in a channel with heated V corrugated upper and lower plates. The parameters studied include the Reynolds number (Re = 2,000–5,500), angles of V corrugated plates (θ = 20°, 40°, 60°), and constant heat fluxs (q″ = 580, 830, 1,090 W/m²). Numerical results have been validated using the experimented data reported by Naphon, and a good agreement has been found. The angles of V corrugated plates (θ) and the Reynolds number are demonstrated to significantly affect the fluid flow and the heat transfer rate. Increasing the angles of V corrugated plates can make the heat transfer performance become better. The increasing Reynolds number leads to a more complex fluid flow and heat transfer rate. The numerical calculations with a non-equilibrium wall function have a better accuracy than with a standard wall function for solving high Reynolds numbers or complex flow problems.     

Lattice Boltzmann simulation of heat transfer and fluid flow in a microchannel with nanofluids

Mathematical modeling is performed to simulate forced convection flow of 47 nm- Al₂O₃/water nanofluids in a microchannel using the lattice Boltzmann method (LBM). Single channel flow and conjugate heat transfer problem are taken into consideration and the heat transfer rate using a nanofluid is examined. Simulations are conducted at low Reynolds numbers (2 ≤ Re ≤ 16). The computed average Nusselt number, which is associated with the thermal conductivity of nanofluid, is in the range of 0.6 ￡ [`(Nu)] ￡ 13 0.6 \le \overline{Nu} \le 13 . Results indicate that the average Nusselt number increases with the increase of Reynolds number and particle volume concentration. The fluid temperature distribution is more uniform with the use of nanofluid than that of pure water. Furthermore, great deviations of computed Nusselt numbers using different models associated with the physical properties of a nanofluid are revealed. The results of LBM agree well with the classical CFD method for predictions of flow and heat transfer in a single channel and a microchannel heat sink concerning the conjugate heat transfer problem, and consequently LBM is robust and promising for practical applications.     

Microscopic particle image velocimetry measurements of transition to turbulence in microscale capillaries

The character of transitional capillary flow is investigated using pressure-drop measurements and instantaneous velocity fields acquired by microscopic PIV in the streamwise–wall-normal plane of a 536 μm capillary over the Reynolds-number range 1,800 ≤ Re ≤ 3,400 in increments of 100. The pressure-drop measurements reveal a deviation from laminar behavior at Re = 1,900 with the differences between the measured and the predicted laminar-flow pressure drop increasing with increasing Re. These observations are consistent with the characteristics of the mean velocity profiles which begin to deviate from the parabolic laminar profile at Re = 1,900, interpreted as the onset of transition, by becoming increasingly flatter and fuller with increasing Re. A fully-turbulent state is attained at Re ≅ 3,400 where the mean velocity profile collapses onto the mean profile of fully-developed turbulent pipe flow from an existing direct numerical simulation at Re = 5,300. Examination of the instantaneous velocity fields acquired by micro-PIV in the range 1,900 ≤ Re < 3,400 reveal that transitional flows at the microscale are composed of a subset of velocity fields illustrating a purely laminar behavior and a subset of fields that capture significant departure from laminar behavior. The fraction of velocity fields displaying non-laminar behavior increases with increasing Re, consistent with past observations of a growing number of intermittent turbulent spots bounded by nominally laminar flow in macroscale pipe flow with increasing Re. Instantaneous velocity fields that are non-laminar in character consistently contain multiple spanwise vortices that appear to streamwise-align to form larger-scale interfaces that incline slightly away from the wall. The characteristics of these “trains” of vortices are reminiscent of the spatial features of hairpin-like vortices and hairpin vortex packets often observed in fully-turbulent wall-bounded flow at both the macro- and micro-scales. Finally, single-point statistics computed from the non-laminar subsets at each transitional Re, including root-mean-square velocities and the Reynolds shear stress, reveal a gradual and smooth maturation of the patches of disordered motion toward a fully-turbulent state with increasing Re.