一个新的声应力系数及其确定

为建立声焦散线与平面应力条件下裂尖应力强度因子的关系,定义了一个新的声应力系数——声程差随应力线性变化的比例系数,该系数的大小既取决于材料常数又取决于耦合介质及声束的传播历程.借助6061-T6铝、EPTI钢两种材料的实验结果,说明了确定新的声应力系数的方法与步骤.所得结论是:只要确定了平面应力条件下超声纵波速度相对变化与主应力和之比,便可确定新的声应力系数.     

?????????Mohr-Coulomb???????????????

在应用Mohr-Coulomb屈服条件时,由于中主应力不影响判别材料是否进入屈服,因此有关中主应力对Mohr-Coulomb材料屈服的影响性质关注较少.考虑Mohr-Coulomb屈服条件与应力路径相关性,本文采用Lode角或Lode数描述了偏平面上屈服性质的分区,对任意满足Mohr-coulomb屈服条件的应力状态,在保持其大、小主应力不变的条件下给出了中主应力在大、小主应力之间变化时的屈服轨迹,从而明确了中主应力对Mohr-Coulomb材料屈服性质的影响.     

超声纯横波法测试45#钢的内部应力

声各向同性的金属材料在应力作用下,材料表现出声各向异性,这是用声弹性法分析材料内部应力的基础。本文用垂直于应力方向传播的超声纯横波对45#钢进行测试,测试时横波的偏振化方向分别平行和垂直于应力方向。实验结果表明:材料在拉、压应力作用下,相互正交的两超声纯横波的声速都发生了变化,且声各向异性因子与应力成线性关系。利用此关系可测试材料内部应力,提供了一种无损测试材料内部应力的方法,另外本实验方法也可以对材料内部残余应力进行评估。实验中利用回振法测量声速,可测量声速的微小变化,精度高。     

混凝土材料三点弯曲破坏的声发射特性

为了研究碎石混凝土材料在不同应力状态下的声发射信号特征,在MTS材料试验机上对混凝土梁进行了三点弯曲实验,并利用先进的多通道声发射系统监测了混凝土梁在三点弯曲载荷下的破坏过程。通过对声发射信号的持续时间、振铃计数、撞击数进行滤波,将混凝土材料破坏过程的声发射信号分成七种类型,同时结合前人关于混凝土材料Kaiser效应的试验研究,将七种类型的声发射信号对应于不同的相对应力水平。研究结果表明,声发射信号的持续时间、振铃计数以及撞击数不仅可以表征混凝土破坏过程的类型,还可以表征混凝土材料所处的应力状态,从而为声发射技术在线监测混凝土材料提供了一种新的途径。     

声弹性应力测量

本文简要评述了声弹性应力测量方法的理论、实验技术和应用等方面的发展概况。平面声弹性技术已取得进展。声弹性用于三维应力和残余应力测量仍有不少困难。     

半平面双材料角界面应力奇异性分布规律的探究

论文对半平面双材料角受集中力问题的界面应力场作了深入的探究,特别着重于双材料角端点附近的界面应力的奇异性分布规律.论文通过对界面应力的严格解和渐近解[16]的比较,发现在双材料角界面端点邻近,严格解和渐近解的差是一个向端点衰减的微幅震荡分布的应力.这个向端点衰减的微幅震荡应力的起始点,称为转换点.自界面端点到转换点,严格解等于渐近解与微幅震荡衰减应力的叠加,称为渐近段.自转换点到无穷远,界面应力由严格解确定,是界面应力的基本段.在基本段内,渐近解单调变化并趋近于零,显著地偏离严格解.所以,转换点将界面应力曲线分成渐近段和基本段.文中讨论了渐近段界面剪应力奇异分布的特点,及半平面双材料角界面端点存在应力奇异性的条件.转换点的意义在于它是渐近段和基本段的过渡点.把转换点代入渐近段的渐近表达式,即可导出表征双材料角奇异性的界面剪应力强度因子与转换点的界面剪应力的关系式.这个关系式将有利于双材料角奇异性初始脱粘判据的研究和建立.     

声程差与应力强度因子的关系

基于弹性状态下力对材料声折射率及试件厚度的影响,推导了含裂纹的试件受力前后,超声纵波经其前后表面反射及透射时声程的变化,得到了应力强度因子与声程差的关系,为通过声程差的变化确定裂尖应力强度因子打下了基础。     

混凝土分段曲线损伤模型

在对比分析国内外现有的混凝土受拉损伤模型基础上，结合素混凝土受拉应力应变曲线的试验结果，提出了一个新的混凝土分段曲线损伤模型，并利用应力连续条件确定了损伤模型中各系数的值。运用该模型到力学分析中，推导了矩形截面的混凝土梁在纯弯矩作用下，在损伤较小和损伤较大时的力学方程，算出了梁的最大承载能力，并与材料力学计算的梁承载能力进行了对比。详细分析了损伤区域及损伤应力在横截面上的变化过程，确定了极限状态下含损伤混凝土梁的应力分布和相应的承载能力，画出了损伤状态梁截面的应力分布图。     

多孔介质——自由流界面应力跳跃条件下流动特性解析解

对非对称多孔介质--自由流复合通道内多孔介质内部及多孔介质与自由流体界面处复杂质量、动量输运特性进行研究. 在多孔介质区采用Brinkman-extended Darcy模型并结合速度连续,剪切应力跳跃的界面条件对此复合通道内流体的传递现象进行求解,提出了考虑界面应力跳跃时非对称复合通道各区域流体运动速度及摩擦系数的解析式,分析了界面应力跳跃系数,达西数及无量纲多孔层偏心厚度对流体速度及摩擦系数的影响. 结果表明:改变界面性质可在一定条件下明显控制各区域流体速度分布;在达西数、多孔层偏心厚度一定情况下,界面应力系数的增大会使界面流速减小,而使流体摩擦系数增大,特别是界面应力系数小于0的情况下变化更明显,此时若不考虑界面应力系数则会造成较大误差. 当界面应力系数及多孔层偏心厚度均为较小负数值时,改变多孔层偏心厚度对界面速度的影响要大于改变界面应力系数的情况;而当界面应力系数及多孔层偏心厚度为较大正数值时,情况则相反. 较大达西数下,界面应力系数及多孔层偏心厚度对流体摩擦系数的影响均较大,继续减小达西数至一定程度时,界面应力系数对流体摩擦系数的影响可忽略不计而认为只与多孔层偏心厚度相关,且对较大多孔层偏心厚度更敏感.      

理想正交各向异性弹塑性材料平面应力条件下Ⅰ型静止裂纹尖端场

在本文中,以 Hill 的塑性理论为基础,详细地讨论了理想正交各向异性弹塑性材料,平面应力条件下Ⅰ型静止裂纹尖端场解。裂纹尖端应力场不包含应力间断线,但包含弹性区。分析的结果表明(i)对于平面应力静止裂纹问题,应力场解不是唯一的,场解中的自由参数必须由远场条件来确定。(ii)裂纹尖端的应力、应变的奇异性,无论是各向异性材料还是各向同性材料,都是相同的。但在各向异性材料中,各向异性参数影响着应力、应变的幅度和分布。     

盾构法隧道模型试验中的相似关系

盾构法是在软土中建造隧道常用的施工法．讨论其模型试验和实物之间的转换问题．根据Goodier理论建立相似关系,考虑了土体的黏弹塑性性质和大变形问题,包括推进压、推进速度、出土量、土体损失率、以及注浆量等施工参数对地层移动的影响．给出的公式可用于盾构法隧道的实验设计和数据分析．     

CONSOLIDATION THEORY OF UNSATURATED SOIL BASED ON THE THEORY OF MIXTURE(Ⅱ)

The present paper uses the mathematics model for consolidation of unsaturatedsoil developed in ref.[1]to solve boundary value problems.The analytical solutionsfor one-dimensional consolidation problem are gained by making use of Laplacetransform and finite Fourier transform.The displacement and the pore water pressureas well as the pore gas pressure are found from governing equations simultaneously.The theoretical formulae of coefficient and degree of consolidation are also given inthe paper.With the help of the method of Galerkin Weighted Residuals,the finiteelement equations for two-dimensional consolidation problem are derived.A FORTRANprogram named CSU8 using8-node isoparameter element is designed.A plane strainconsolidation problem is solved using the program,and some distinguishing features onconsolidation of unsaturated soil and certain peculiarities on numerical analysis arerevealed.These achievements make it convenient to apply the theory proposed by theauthor in engineering practice.     

饱和土地基的非轴对称固结

固结问题是土力学的基础课题之一，现有的研究主要针对饱和土的平面固结和轴对称固结问题。本文应用Fourier展开、Laplace变换和Hankel变换求解了各向同性饱和土的Blot固结方程；讨论了半空间各向同性饱和土的非轴对称固结。借助数值计算，本文的方法可以用于分析各向同性饱和土的非轴对称固结问题。     

循环载荷下砂质土的本构模型

提出了一个描述砂质土循环载荷条件下主要特性的本构模型，并且采用不同围压下多种加载途径的土力学实验确定了模型中的待定材料常数，由本构模型的增量工数值积分计算所得到的理论曲线与不同应力路径下实验曲线十分接近，经实验验证这种本构模型能广泛地应用土工问题的弹－塑性有限元分析中。     

SEMI-ANALYTICAL AND SEMI-NUMERICAL METHOD FOR DYNAMIC ANALYSIS OF FOUNDATION

A semi-analytical and semi-numerical method is proposed for the dynamic analysis of foundations. The Lamb's solution and the approximate formulae were used to establish the relation of the contact force and deflection between the foundation and soil. Therefore, the foundation can be separated from soil and analyzed by FEM as for the static cases. The plate can be treated as that the known forces are acting on the upper surface, and the contact pressure from soil can be represented as the deflection. So that only the plate needs to be divided into elements in the analysis. By this method, a series of vibration problems, including various shapes and rigidities of foundations, different excitation frequencies, were analyzed. Furthermore, it can be used for the embedded foundation. The numerical examples show that this method has simplicity, highly accurate and versatile. It is an effective method for the dynamic analysis of foundations.     

临近既有地下室平动模式挡土墙主动土压力研究

对于挡土墙距既有地下室很近,挡土墙与既有地下室外墙之间的填土宽度有限的情形,采用经典的库伦、郎肯土压力理论计算挡墙主动土压力是不合适的,设计偏于保守.本文基于库伦滑动土楔假定,考虑地面超载以及墙土之间的摩擦作用,推导出了临近既有地下室的挡土墙主动极限状态下滑裂面倾角和主动土压力系数的解析公式.分析结果表明滑裂面倾角、主动土压力系数与填土宽高比、土内摩擦角、墙土摩擦角以及地面超载等因素有关.并与经典土压力理论及前人研究成果进行对比,所得结论对实际工程有参考价值.     

The slip and drift model of a wheel with tyre compared to some other attempts in this field

The Slip and Drift Model (SDM) of a wheel with tyre, introduced in 1969, has brought the formally correct fundamental solution to the two-dimensional problem of a wheel motion: longitudinal force-lateral force-slip-drift (slip angle) relationship. It has taken into account the tyre elasticity and the specifics of soil behaviour. In some recent attempts to compile a modified model, the SDM was either ignored or presented inadequately. The analysis of two such attempts from 1981 and 1987 has revealed that their kinematic formulae reproduce the basic formulae of the SDM and that their static equilibrium formulae, as far as they are based on the resolution of the soil shear stress into x, y components, are not satisfactory as a matter of principle.     

The applicability of the MMP concept in specifying off-road mobility for wheeled and tracked vehicles

A review is given of the use of mean maximum pressure (MMP) in specifying off-road performance of vehicles. The need to quote a single mobility criterion which is unbiased in favour of either wheeled or tracked vehicles is recognised. The difficulties which researchers have encountered in developing expressions for MMP for both wheeled and tracked vehicles which correctly describe their relative performance are highlighted. Predictions of MMP for wheeled vehicles are compared with ground pressure measurements for a number of vehicles and it is shown that the MMP parameter does not actually represent the ground pressure accurately. Finally it is argued that the only safe route for the specifier is to quote a range of soil types, conditions and gradients on which the vehicle is to operate. This shifts the responsibility to the designer but also clears the way for innovative design, beyond the constraints of the MMP formulae.     

On the Formation of Discontinuities of Wave Fronts in a Saturated Granular Body

The paper deals with propagation of plane wave fronts in a solid with a non-linear relation between stress and deformation. The objective is to calculate the distance that a wave front covers before it loses continuity. The formulae derived for a general quasi-linear system of two equations are applied to the propagation of plane compression waves in dry and partially saturated granular bodies. In the case of a saturated body with gas bubbles, the influence of gas and capillary pressure on the stiffness of the body is taken into account. Numerical calculations relevant to soil mechanics are presented. For the numerical calculations a constitutive equation of the hypoplasticity theory for granular materials has been used. Received November 1, 1997     

基于双剪统一强度理论的厚壁圆筒塑性极限载荷分析

应用双剪统一强度理论,考虑材料的拉压异性和同性,推导了在内压和轴力联合作用下的厚壁圆筒的塑性极限载荷表达式在该表达式中,当其系数取不同的值时,就能得到按Tresca屈服准则、线性逼近的Mises屈服准则和双剪应力屈服准则进行计算的结果.