激光钝化对熔石英修复后损伤性能影响的实验研究

采用10.6 μupm 的 CO₂激光, 对单次激光脉冲辐照修复熔石英存在的烧蚀采用大光斑钝化去除. 经过辐照修复的区域置于前表面测试初始损伤阈值, 结果表明调制造成的损伤得到了一定程度的抑制; 辐照区域置于后表面修复后 熔石英的初始损伤阈值超过了基底的初始损伤阈值. 实验观察到了应力分布外扩, 同时明显减弱. 对损伤增长的测试说明, 经过激光熔融辐照后的损伤点, 当应力释放以后, 损伤扩展初期表现出指数增长趋势, 后期随着辐照次数的增加, 损伤增长不再明显, 并且趋于恒定值.     

预处理对355nm激光作用下熔石英损伤增长的影响

测试了经化学蚀刻、紫外激光预处理及其共同处理后的熔石英355 nm激光损伤阈值;研究了处理前后其损伤斑面积随激光辐照脉冲数的增长情况。结果表明,处理后熔石英355 nm激光损伤阈值得到了提高,且损伤斑面积增长变慢。利用CO2激光对熔石英表面损伤点进行了修复处理,修复后的损伤点R-on-1抗损伤阈值和基底阈值相当,损伤增长得到有效抑制。     

CO2激光对熔石英表面小尺寸损伤的修复

 利用10.6 μm的CO₂激光对不同直径的点状损伤和不同宽度的划痕进行了修复。经过波长351 nm的紫外激光考核发现,对于直径小于80 μm的点状损伤和对于宽度小于40 μm的划痕,随着损伤点尺寸和划痕宽度的增加,修复后阈值提高程度逐渐降低。划痕的宽度在达到40 μm以后修复效果非常微弱。修复过程中,由于作用时间较短及温度分布不均产生了热应力导致样片损伤以后产生径向裂痕,后续的紫外激光会使裂痕明显扩展。当样品被置于高温退火炉内退火3 h以后,应力导致开裂的现象得到了解决。     

用1064nm激光增强HfO2/SiO2薄膜的抗激光损伤能力的实验研究

 用1 064nm激光实验研究了HfO₂/SiO₂薄膜的激光损伤增强效应，实验以薄膜激光损伤阈值70%的激光能量开始，采用N-ON-1方式处理薄膜，激光脉冲的能量增量为5J/cm²。实验结果表明，激光处理薄膜表面能使激光损伤阈值平均提高到3倍左右，并且薄膜的损伤尺度也明显减小。对有缺陷的薄膜，其缺陷经低能量激光后熔和消除，其抗激光损伤能力得到增强，但增强得并不显著，而薄膜本身的激光预处理，可以使其激光损伤阈值大大提高。     

化学法制备的HfO2薄膜的激光损伤阈值研究

 采用化学法制备了HfO₂介质膜，研究了热处理、紫外辐照以及Al₂O₃复合对HfO₂介质膜激光损伤阈值的影响。采用红外光谱（FTIR）和X射线衍射仪对薄膜进行了表征，并用输出波长为1.064 μm、脉宽为10 ns的电光调Q激光系统测试薄膜的激光损伤阈值。实验结果表明：采用150 ℃左右的温度对薄膜进行热处理可以提高薄膜的激光损伤阈值，所获得的薄膜的激光损伤阈值高达42.32 J/cm²，比热处理前的激光损伤阈值提高了82%；无机材料Al₂O₃的适量添加能够提高薄膜的激光损伤阈值，其中HfO₂与Al₂O₃的最佳质量配比约为95∶5；另外，对薄膜进行适当的紫外辐照也可改善HfO₂ 薄膜以及HfO₂-Al₂O₃复合薄膜的抗激光损伤性能。紫外辐照对提高HfO₂-Al₂O₃复合薄膜的激光损伤阈值效果尤为显著，辐照40 min后的激光损伤阈值达到44.33 J/cm²，比紫外辐照前的激光损伤阈值提高了90%。     

预应力对熔石英损伤的影响

采用ANSYS进行形变-应力模拟。对不同应力状态下的熔石英表面进行三倍频激光损伤测试,结果发现,预加压应力为0~50 MPa时损伤阈值有明显提高的趋势,用应力耦合作用对此给出了解释：0~50 MPa的预加压应力可以降低和抵消激光辐照产生的张应力破坏,大于50 MPa预应力的耦合作用会使得该处机械性能下降,另外,损伤增长在预应力存在时更容易发生。因此,0~50 MPa预加压应力时的表面预应力可以提高熔石英的抗激光辐照能力。     

杂质对溶胶-凝胶SiO2薄膜激光损伤的影响

 采用溶胶-凝胶法制备了含有吸收性杂质和非吸收性杂质的SiO₂增透膜,采用波长为1 064 nm的激光对其进行了小光斑激光预处理,对比研究了预处理前后的激光损伤差异,研究表明：激光预处理对于洁净的SiO₂薄膜影响不大;含10 μm SiO₂颗粒杂质的样品微透镜效应很明显,容易成为损伤起始的种子,激光预处理后情况有所改善;含有CeO₂颗粒杂质的样品表现出了很强的吸收性质,损伤阈值降低到不足洁净样品的一半。所有样品激光预处理后损伤形貌未发生变化,透光率峰值均有约50 nm的蓝移。     

氧分压对ZrO2薄膜激光损伤阈值的影响

 在不同的氧分压下用电子束热蒸发的方法制备了ZrO₂薄膜。分别通过X射线衍射、光学光谱、热透镜技术、抗激光辐照等测试，对所制备样品的微结构、折射率、吸收率及激光损伤阈值进行了测量。实验结果表明，薄膜中晶粒主要是四方相为主的多晶结构，并且随着氧分压的增加，结晶度、折射率以及弱吸收均逐渐降低。薄膜的激光损伤阈值开始随着氧分压增加从18.5J/cm²逐渐增加，氧分压为9×10^-3Pa时达到最大，值为26.7 J/cm²，氧分压再增加时则又降低到17.5 J/cm²。由此可见，氧分压引起的薄膜微结构变化是ZrO₂薄膜激光损伤阈值变化的主要原因。     

CO_2激光预处理参数对石英基片表面粗糙度的影响

为研究CO2激光预处理参数对熔石英基片表面粗糙度的影响,采用频率为100 Hz,光斑面积为1 mm2的CO2激光对理想的熔石英基片进行辐照处理,根据处理后基片表面微观形貌特征将修复程度分别定义为轻度、中度和重度修复,并对3种修复程度下基片的表面粗糙度值进行了统计。研究了不同脉冲作用时间和不同占空比(激光功率)的激光束单点单次辐照基片后的表面粗糙度。结果表明:石英基片的表面粗糙度均方根值和处理造成的凹陷深度均随脉冲作用时间和功率的增加逐渐变大;均方根值的增幅逐渐增加,凹陷深度的增幅逐渐减小。     

CO2激光局域辐照对熔石英损伤特性的影响

研究了CO₂激光局域辐照对熔石英损伤特性的影响, 发现当辐照中心温度较低时(1139 K), 辐照对损伤阈值没有明显影响, 但辐照中心温度较高时(1638 K), 辐照对损伤阈值有明显的影响, 损伤阈值随距离辐照中心间距的增大而减小, 在残余应力产生光程差最大处附近, 损伤阈值降到最小, 随着与辐照中心间距的进一步增加, 损伤阈值略有上升. 对导致此现象的原因做了分析. 由于残余应力的存在, 在辐照中心发生再损伤产生的裂纹后, 裂纹先沿径向扩展, 在残余应力产生光程差最大处附近, 裂纹转而向切向扩展, 这可能与径向和环向张应力随半径的变化有关. 在采用热处理炉退火消除残余应力时, 必须注意元件的洁净处理, 否则退火会出现析晶现象, 对损伤阈值和透射率造成不良影响. 关键词： 2激光局域辐照')" href="#">CO₂激光局域辐照 熔石英 损伤特性     

Two localized CO2 laser treatment methods for mitigation of UV damage growth in fused silica

Two methods：high-power,short-time,single-shot irradiation（Method A） and low-power,long-time,multi-shot irradiation（Method B） are investigated to mitigate the UV damage growth in fused silica by using a 10.6-μm CO2 laser.To verify the mitigation effect of the two methods,the laser induced damage thresholds（LIDTs） of the mitigated sites are tested with a 355-nm,6.4-ns Nd：YAG laser,and the light modulation of the mitigation sites are tested with a 351-nm continuous Nd：YLF laser.The mitigated damaged sites treated with the two methods have almost the same LIDTs,which can recover to the level of pristine material.Compared with Method A,Method B produces mitigated sites with low crater depth and weak light modulation.In addition,there is no raised rim or re-deposited debris formed around the crater edge for Method B.Theoretical calculation is utilized to evaluate the central temperature of the CO2 laser beam irradiated zone and the radius of the crater.It is indicated that the calculated results are consistent with the experimental results.     

Surface evolution and laser damage resistance of CO2 laser irradiated area of fused silica

A 10.6 μm CO₂ laser has been reported to effectively mitigate the laser damage growth of fused silica. Two zones of the laser irradiated area are defined in this work: the distorted zone and the laser affected zone. The parameters of the two zones are studied at different CO₂ laser beam sizes, irradiation times, and powers by microscopy, profilometry, and photoelastic method. The results show that the diameter of laser affected zone is almost completely determined by the laser beam size and the distorted zone is associated with the mitigation range of CO₂ laser beam. The diameter and depth of the distorted zone increase as the laser power and irradiation time increase. The depth grows exponentially depending on the irradiation time. The maximum residual stress discrepancy is located near the boundary of the laser affected zone. The laser damage resistance test results show that the distorted zone and the laser affected zone have a better damage resistance than the original substrate.     

CO2激光扫描辐照修复熔石英表面损伤

采用振镜系统结合10.6 m的CO2激光,对熔石英表面损伤点进行辐照,成功地修复了直径500 m的大尺寸损伤点,损伤修复后表面无烧蚀残留,损伤内部完全愈合,无气泡和残余裂纹。和定点修复方式相比,这种修复具有修复尺度大、面形影响区域小、应力分布范围小的优势。80%扫描辐照修复的损伤点的初始损伤阈值恢复甚至超过了基底的初始损伤阈值。     

Influences of CO2 laser annealing on mechanical and laser-induced damage properties of ZrO2 thin films

Zirconium dioxide (ZrO₂) thin films were deposited on BK7 glass substrates by the electron beam evaporation method. A continuous wave CO₂ laser was used to anneal the ZrO₂ thin films to investigate whether beneficial changes could be produced. After annealing at different laser scanning speeds by CO₂ laser, weak absorption of the coatings was measured by the surface thermal lensing (STL) technique, and then laser-induced damage threshold (LIDT) was also determined. It was found that the weak absorption decreased first, while the laser scanning speed is below some value, then increased. The LIDT of the ZrO₂ coatings decreased greatly when the laser scanning speeds were below some value. A Nomarski microscope was employed to map the damage morphology, and it was found that the damage behavior was defect-initiated both for annealed and as-deposited samples. The influences of post-deposition CO₂ laser annealing on the structural and mechanical properties of the films have also been investigated by X-ray diffraction and ZYGO interferometer. It was found that the microstructure of the ZrO₂ films did not change. The residual stress in ZrO₂ films showed a tendency from tensile to compressive after CO₂ laser annealing, and the variation quantity of the residual stress increased with decreasing laser scanning speed. The residual stress may be mitigated to some extent at proper treatment parameters.     

Irradiation effects of CO2 laser parameters on surface morphology of fused silica

To understand the surface morphology evolution of fused silica induced by 10.6-μm CO2 laser irradiation at different parameters,this paper reports that optical microscopy,profilometry,and hydrophilicity tests are utilized to characterize the surface structure and roughness of the laser irradiated area. The results show that three typical surface morphologies and two typical hydrophilicity test images are observed at different laser powers and pulse durations. The correlations between surface temperature and surface morphology as well as hydrophilicity behaviours are presented. The different hydrophilicity behaviours are related to surface structures of the laser-induced crater and thermal diffusion area. The thermal diffusion length monotonously increases with increasing laser power and pulse duration. The crater width is almost determined by the laser beam size. The crater depth is more sensitive to the laser power and pulse duration than the crater width.     

Gas breakdown with nanosecond CO2 laser radiation

The thresholds for CO₂ laser induced breakdown and their variation with pulse width have been measured at various pressures for Ar, N₂ and an 8/1/1 laser mixture of He/CO₂/N₂ using 3–40 ns duration pulses. These measurements indicate that excited state production plays a dominant role in determining the threshold for nanosecond duration pulses. This has been confirmed by the good agreement obtained between the measured and theoretical thresholds.     

CO2 laser cutting of slate

Slate is a natural stone which has the characteristic that shows a well-developed defoliation plane, allowing to easily split it in plates parallel to that plane which are particularly used as tiles for roof building. At present, the manufacturing of slate is mostly manual, being noisy, powdery and unsafe for the worker. Thus, there is a need to introduce new processing methods in order to improve both the working conditions and the quality of the products made of slate.Following the previous work focused on the drilling and cutting of slate tiles using a Nd : YAG laser, we present in this paper the results of the work carried out to explore the possibilities to cut slate plates by using a CO₂ laser. A 1.5 kW CO₂ laser was used to perform different experiments in which, the influence of some processing parameters (average power, assist gas pressure) on the geometry and quality of the cut was studied. The results obtained show that the CO₂ laser is a feasible tool for a successful cutting of slate.     

Mathematical modeling of hybrid CO2 laser

A Teller–Landau six-temperature model describing the dynamic emission of single-mode TEA CO₂ laser has been adapted. This model has been also used to describe the mechanism of obtaining relatively high-power output pulses from hybrid TE-TEA or CW-TEA CO₂ laser consisting of high- and low-pressure sections. The suggested mathematical model allows to investigate the mechanism which limits the TEA oscillation to single longitudinal mode (SLM) due to the narrow gain bandwidth of low-pressure section, and also to study the effect of the laser input parameters on the smooth output laser pulse parameters. In addition, numerical solutions of non-linear rate equation system of the suggested model are quantitatively discussed. The solutions describe the radiation field intensity, the population inversion, and the energy transfer processes. The calculated values of maximum peak power, total energy in pulse, pulse width, etc. are in a very good agreement with the observed experimental values.