Growth of In nanocrystallite arrays on the Si(1 0 0)-c(4 × 12)-Al surface

Using scanning tunneling microscopy, growth of In nanoisland arrays on the Si(1 0 0)-c(4 × 12)-Al surface has been studied for In coverage up to 1.1 ML and substrate temperature from room temperature to 150 °C. In comparison to the case of In deposition onto the clean Si(1 0 0) surface or Si(1 0 0)4 × 3-In reconstruction, the In growth mode is changed by the c(4 × 12)-Al reconstruction from the 2D growth to 3D growth, thus displaying a vivid example of the Volmer-Weber growth mode. Possible crystal structure of the grown In nanoislands is discussed.     

Growth of (√3 × √3)-Ag and (1 1 1) oriented Ag islands on Ge/Si(1 1 1) surfaces

We have studied the growth of Ag on Ge/Si(1 1 1) substrates. The Ge/Si(1 1 1) substrates were prepared by depositing one monolayer (ML) of Ge on Si(1 1 1)-(7 × 7) surfaces. Following Ge deposition the reflection high energy electron diffraction (RHEED) pattern changed to a (1 × 1) pattern. Ge as well as Ag deposition was carried out at 550 °C. Ag deposition on Ge/Si(1 1 1) substrates up to 10 ML has shown a prominent (√3 × √3)-R30° RHEED pattern along with a streak structure from Ag(1 1 1) surface. Scanning electron microscopy (SEM) shows the formation of Ag islands along with a large fraction of open area, which presumably has the Ag-induced (√3 × √3)-R30° structure on the Ge/Si(1 1 1) surface. X-ray diffraction (XRD) experiments show the presence of only (1 1 1) peak of Ag indicating epitaxial growth of Ag on Ge/Si(1 1 1) surfaces. The possibility of growing a strain-tuned (tensile to compressive) Ag(1 1 1) layer on Ge/Si(1 1 1) substrates is discussed.     

Structural analysis of the c(4 × 2) reconstruction in Si(0 0 1) and Ge(0 0 1) surfaces by low-energy electron diffraction

The c(4 × 2) structures in (0 0 1) surfaces of Si and Ge have been studied by low-energy electron diffraction (LEED). Using a proper cleaning method for the Si surface, we were able to observe clear c(4 × 2) LEED patterns up to incident energy of ∼400 eV as well as the Ge surface. Extensive experimental intensity-voltage curves allowed us to optimize the asymmetric dimer model up to the eighth layer (including the dimer layer) in depth in the dynamical LEED calculation. Optimized structural parameters are almost the same for the Si and Ge except for the height of the buckled-up atom of the asymmetric dimer. For the Ge surface, the structural parameters are in excellent agreement with those obtained by a previous theoretical calculation. The tilt angle and bond length of the dimer are 18 ± 1 (19 ± 1)° and 2.4 ± 0.1 (2.5 ± 0.1) Å for the Si(0 0 1) (Ge(0 0 1)), respectively.     

Ordered arrangement of 9-aminoanthracene on Au(1 1 1) surfaces: A scanning tunneling microscopy study

We present a scanning tunneling microscopy (STM) investigation of 9-aminoanthracene (AA) on the reconstructed Au(1 1 1) surface. The bare Au(1 1 1) surface shows the herringbone reconstruction which is conserved upon deposition of the organic molecules. Most of the AA molecules are found to decorate the regions of fcc-stacking of the gold surface where a periodic linear arrangement is observed. The orientation of the long molecule axis of individual molecules is along the -directions of the Au substrate. In addition, for individual domains of the surface reconstruction, one of the three possible orientations is preferred. On substrate areas which exhibit a high step density, the steps are completely decorated by AA molecules. A detailed analysis of the STM images reveals that the molecules are located on top terrace levels. The fine structure of individual molecules on the terrace shows a clear dependence on the tunneling voltage and resembles the molecular orbitals of the free AA molecule.     

Surface structure analysis of metal adsorbed Si(1 1 1) surfaces by Patterson function with LEED I-V curves

Wu and Tong proposed the calculation method of Patterson function obtained directly from the LEED I-V curves which shows the relative position of surface atoms as an image. We have made the calculation program of Patterson function and applied to the structural analysis of the Si(1 1 1)1 × 1-Fe surface. Surface structure was able to be expressed almost correctly by the Patterson function obtained from the theoretical I-V curves for the model structure. In the Patterson function obtained from the experimental I-V curves, the locational relation between the atoms of subsurface layer was in agreement with the CsCl type structure. More over, because the faint peak, by which we can distinguish the model, can be seen, it seems that the model B8 is preferable to the model A8. This result is consistent with the model shown by Walter et al.     

Adsorption of 2-butyne on Si(0 0 1) at room temperature: A valence band photoemission study

We present an angle resolved ultraviolet photoemission spectroscopy study of the adsorption of 2-butyne (CH₃-CC-CH₃) on Si(0 0 1)-2 × 1 at room temperature. We recorded valence band photoemission spectra for two azimuthal positions of a vicinal silicon surface, where all the rows formed by the surface silicon dimers are parallel. The photoemission symmetry selection rules allow the determination of the orientation of the molecular orbitals. The photoemission signal of the HOMO is enhanced when the electric field is parallel to the dimer rows. This showed that the π orbital left intact after the cyclo-addition reaction of the molecule with one silicon dimer is parallel to the dimer rows. This indicates that each 2-butyne molecule adsorbs on one silicon dimer. In spite of the size of the system and the vicinity of the orbitals, the angle resolved study points out that no dispersion of the electronic bands occurs. Not all the surface dimers are reacted so some disorder still exists on the surface preventing the formation of Bloch states.     

Sulphur overlayers on the Au(1 1 0) surface: LEED and TPD study

The adsorption and desorption of sulphur on the clean reconstructed Au(1 1 0)-(1 × 2) surface has been studied by low energy electron diffraction, Auger electron spectroscopy and temperature programmed desorption. The results obtained show a complex behaviour of the S/Au(1 1 0) system during sulphur desorption at different temperatures. Two structures of the stable ordered sulphur overlayer on the Au(1 1 0) surface, p(4 × 2) and c(4 × 4), were found after annealing the S/Au(1 1 0) system at 630 K and 463 K, respectively. The corresponding sulphur coverage for these overlayers was estimated by AES signal intensity analysis of the Au NOO and S LMM Auger lines to be equal to 0.13 ML and 0.2 ML, respectively. Both sulphur structures appear after removing an excess of sulphur, which mainly desorbs at 358 K as determined from TPD spectra. Furthermore, it was not possible to produce the lower coverage p(4 × 2) sulphur structure by annealing the c(4 × 4) surface. In the case of the p(4 × 2) S overlayer on the Au(1 1 0)-(1 × 2) surface it is proposed that the sulphur is attached to “missing row” sites only. The c(4 × 4) S overlayer arises via desorption of S₂ molecules that are formed on the surface due to mobility of sulphur atoms after a prolonged anneal.     

Fabrication of nanostructures by selective growth of C60 and Si on Si(1 1 1) substrate

Using two types of selective growth, selective C₆₀ growth and selective Si growth, on a common Si(1 1 1) substrate, an array of C₆₀ nanoribbons with controlled values of width and thickness is fabricated. On a surface that has Si(1 1 1)√3 × √3R30°-Ag (referred to as Si(1 1 1)√3-Ag hereafter) and bare Si(1 1 1) regions at the same time, the preferential growth of C₆₀ multilayered film is recognized on the Si(1 1 1)√3-Ag region. The growth of Si selectively occurs on a bare Si(1 1 1) region if the substrate surface has C₆₀-adsorbed and bare Si(1 1 1) regions at the same time. As a demonstration of the use of these selective growths, we fabricate an array of well-isolated C₆₀ nanoribbons, which show a well-ordered molecular arrangement and have sizes of about 40 nm in widths and 3-4 nm in thicknesses.     

Epitaxial growth of Bi thin films on Ge(1 1 1)

We investigated Bi thin film growth on Ge(1 1 1) by using low-energy electron diffraction (LEED) and scanning tunneling microscopy (STM). In the submonolayer regime, adsorbed Bi atoms form patches of the (2×1) structure. However, the structure does not grow to a long-range order. Following the formation of a (1×1) monolayer (ML) film, two-dimensional (1 1 0)-orientated Bi islands grow. The film orientation changes from (1 1 0) to (1 1 1) at 6-10 ML. The (1 1 0)-oriented Bi film shows a six-domain LEED pattern with missing spots, associated with a glide-line symmetry. The hexagonal (1 1 1) film at 14 ML has a lattice constant 2% smaller than bulk Bi(1 1 1).     

Initial oxidation of Ni(1 1 1) observed by electron emission microscopy: PEEM and MEEM

The initial oxidation of Ni(1 1 1) in the temperature range of 550-700 K has been monitored by photoelectron emission microscopy (PEEM) and metastable-atom electron emission microscopy (MEEM). The PEEM and MEEM images show uniform patterns for the chemisorbed overlayer, reflecting the electronic homogeneity as seen at the μm scale. During the nucleation and lateral growth of oxide, however, the μm-scale pattern due to the formation of oxide domains appears and its evolution depends strongly on the substrate temperature and dose pressure of gaseous O₂. Our data indicate that the high-temperature oxidation is regarded as a successive multi-nucleation process in a reaction-diffusion field.     

Optical anisotropy of the In/Si(1 1 1)(4 × 1)/(8 × 2) nanowire array

Ab initio calculations of the reflectance anisotropy of Si(1 1 1)-In surfaces are presented. A very pronounced optical anisotropy around 2 eV is found that is related to In-chain states. The distortion of the indium chains characteristic for the (4 × 1) → (8 × 2) phase transition results in a splitting of the 2 eV peak, as observed experimentally. The splitting occurs irrespective wether the phase transition occurs according to the trimer or hexamer model.     

Germanium growth on Br-terminated Si(1 0 0)

The consequences of Ge deposition on Br-terminated Si(1 0 0) were studied with scanning tunneling microscopy at ambient temperature after annealing at 650 K. One monolayer of Br was sufficient to prevent the formation of Ge huts beyond the critical thickness of 3 ML. This is possible because Br acts as a surfactant whose presence lowered the diffusivity of Ge adatoms. Hindered mobility was manifest at low coverage through the formation of short Ge chains. Further deposition resulted in the extension and connection of the Ge chains and gave rise to the buildup of incomplete layers. The deposition of 7 ML of Ge resulted in a rough surface characterized by irregularly shaped clusters. A short 800 K anneal desorbed the Br and allowed Ge atoms to reorganize into the more energetically favorable “hut” structures produced by conventional Ge overlayer growth on Si(1 0 0).     

Growth kinetics of metastable (3 3 1) nanofacet on Au and Pt(1 1 0) surfaces

A theoretical epitaxial growth model with realistic barriers for surface diffusion is investigated by means of kinetic Monte Carlo simulations to study the growth modes of metastable (3 3 1) nanofacets on Au and Pt(1 1 0) surfaces. The results show that under experimental atomic fluxes, the (3 3 1) nanofacets grow by 2D nucleation at low temperature in the submonolayer regime. A metastable growth phase diagram that can be useful to experimentalists is presented and looks similar to the one found for the stationary growth of the bcc(0 0 1) surface in the kinetic 6-vertex model.     

Interaction of 2,2,6,6-tetramethyl-3,5-heptanedione with the Si(1 0 0)-2 × 1 surface: Scanning tunneling microscopy and density functional theory study

Room temperature adsorption and reaction of 2,2,6,6-tetramethyl-3,5-heptanedione (dpmH) on the Si(1 0 0)-2 × 1 surface has been studied with ultra-high vacuum scanning tunneling microscopy (UHV-STM) and temperature programmed desorption (TPD). The molecule is found to chemisorb as a mixture of at least five distinct species. Density functional theory (DFT) was used to calculate the structures and adsorption energies of 12 possible addition products. Unique bonding assignments for each experimental feature are proposed by consideration of a common intermediate reaction network, and a comparison of possible reaction pathways leading to the final products. These assignments are: OH inter-dimer dissociation, OH intra-dimer dissociation, 1,5 intra-dimer addition, 1,5 inter-dimer addition, and intra-dimer [2 + 2]CO addition with OH dissociation on an adjacent dimer. TPD and STM results show that the molecule dissociates completely upon annealing to 700 °C with formation of the c(4 × 4) phase at low exposures, and SiC islands for exposures exceeding 0.15 L.     

Adsorption of organic molecules by photochemical reaction on Cl:Si(1 1 1) and H:Si(1 1 1) evaluated by HREELS

The covalent attachment of alkyl groups to silicon surfaces, via carbon-silicon bond formation, has been attempted using gas-surface reactions starting from Cl-terminated Si(1 1 1) or H:Si(1 1 1) under ultraviolet light irradiation. The formation of Cl-terminated Si(1 1 1) and its resulting stability were examined prior to deposition of organic molecules. High-resolution electron energy loss spectroscopy (HREELS) was utilized for detecting surface-bound adsorbates. The detection of photo-deposited organic species on Cl:Si(1 1 1) from gas-phase CH₄ or CH₂CH₂ was not significant. On H:Si(1 1 1), it was evident that after the photoreaction with gas-phase C₂H₅Cl, C₂H₅ groups were chemically bonded to the surface Si atoms through single covalent bonds. The C₂H₅ groups were thermally stable at temperatures below 600 K. Alkyl monolayers prepared on silicon surfaces by dry process will lead to a new prospective technology of nanoscale fabrication and biochemical applications.     

Adsorption of water on thin V2O3(0 0 0 1) films

V₂O₃(0 0 0 1) films have been grown epitaxially on Au(1 1 1) and W(1 1 0). Under typical UHV conditions these films are terminated by a layer of vanadyl groups as has been shown previously [A.-C. Dupuis, M. Abu Haija, B. Richter, H. Kuhlenbeck, H.-J. Freund, V₂O₃(0 0 0 1) on Au(1 1 1) and W(1 1 0): growth, termination and electronic structure, Surf. Sci. 539 (2003) 99]. Electron irradiation may remove the oxygen atoms of this layer. H₂O adsorption on the vanadyl terminated surface and on the reduced surface has been studied with thermal desorption spectroscopy (TDS), vibrational spectroscopy (IRAS) and electron spectroscopy (XPS) using light from the BESSY II electron storage ring in Berlin. It is shown that water molecules interact only weakly with the vanadyl terminated surface: water is adsorbed molecularly and desorbs below room temperature. On the reduced surface water partially dissociates and forms a layer of hydroxyl groups which may be detected on the surface up to T ∼ 600 K. Below ∼330 K also co-adsorbed molecular water is detected. The water dissociation products desorb as molecular water which means that they recombine before desorption. No sign of surface re-oxidation could be detected after desorption, indicating that the dissociation products desorb completely.     

Structural study of Si(1 1 1)-6 × 1-Ag surface using surface X-ray diffraction

The surface structure of Si(1 1 1)-6 × 1-Ag was investigated using surface X-ray diffraction techniques. By analyzing the CTR scattering intensities along 00 rod, the positions of the Ag and reconstructed Si atoms perpendicular to the surface were determined. The results agreed well with the HCC model proposed for a 3 × 1 structure induced by alkali-metals on a Si(1 1 1) substrate. The heights of the surface Ag and Si atoms did not move when the surface structure changed from Si(1 1 1)-√3 × √3-Ag to Si(1 1 1)-6 × 1-Ag by the desorption of the Ag atoms. From the GIXD measurement, the in-plane arrangement of the surface Ag atoms was determined. The results indicate that the Ag atoms move large distances at the phase transition between the 6 × 1 and 3 × 1 structures.     

Molecular dynamics simulation of CH3 interaction with Si(1 0 0) surface

Molecular dynamics simulations of the CH₃ interaction with Si(1 0 0) were performed using the Tersoff-Brenner potential. The H/C ratio obtained from the simulations is in agreement with available experimental data. The results show that H atoms preferentially react with Si. SiH is the dominant form of SiH_x generated. The amount of hydrogen that reacts with silicon is essentially energy-independent. H atoms do not react with adsorbed carbon atoms. The presence of C-H bonds on the surface is due to molecular adsorption.     

Layer-resolved photoelectron diffraction from Si(0 0 1) and GaAs(0 0 1)

Photoelectron diffraction in the layer-resolved mode brings more detailed information about local atomic arrangement than is obtained in the standard mode. This is demonstrated in crystals with diamond and zinc-blende structures, both for unpolarized photon excitation as well as for circularly polarized excitation. The full angular distributions of photoemission intensities are evaluated for large atomic clusters representing ideally truncated surfaces of Si(0 0 1) and GaAs(0 0 1). Highly structured layer-resolved patterns enable a more detailed understanding of the standard mode outcomes. Photoelectron intensities from atomic layers placed at different depths under the crystal surface provide direct evidence about electron attenuation and its anisotropy in crystals.     

Self-assembly of zwitterionic molecules on a Au(23 23 21) surface at low temperature

The adsorption of zwitterionic (E) 4-methoxy-4′-(3-n-sulfonatopropyl)stilbazolium (MSPS) molecules on the stepped vicinal Au(23 23 21) surface was studied by scanning tunneling microscopy (STM) at low temperature as a function of the molecular coverage. At the sub-half monolayer, a supramolecular network based on MSPS is preferentially adsorbed onto face-centered cubic stacking regions. At the monolayer, a complete periodic supramolecular film is obtained.