Synthesis of In-doped Ga2O3 zigzag-shaped nanowires and optical properties

In-doped Ga₂O₃ zigzag-shaped nanowires and undoped Ga₂O₃ nanowires have been synthesized on Si substrate by thermal evaporation of mixed powders of Ga, In₂O₃ and graphite at 1000 °C without using any catalyst via a vapor-solid growth mechanism. The morphologies and microstructures of the products were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and photoluminescence spectroscopy (PL). The nanowires range from 100 nm to several hundreds of nanometers in diameter and several tens of micrometers in length. A broad emission band from 400 to 700 nm is obtained in the PL spectrum of these nanowires at room temperature. There are two blue-emission peaks centering at 450 and 500 nm, which originate from the oxygen vacancies, gallium vacancies and gallium-oxygen vacancy pairs.     

Synthesis and characterization of axially periodic Zn2SnO4 dendritic nanostructures

Zn2SnO4 （ZTO） nanowires with a unique dendritic nanostructure were synthesized via a simple one-step thermal evaporation and condensation process. The morphology and microstructure of the ZTO nanodendrite have been investigated by means of field emission scanning electron microscopy （SEM）, x-ray diffraction （XRD） and high-resolution transmission electron microscopy （HRTEM）. SEM observation revealed the formation of branched nanostructures and showed that each branch exhibited a unique periodic structure formed by a row of overlaid rhombohedra of ZTO nanocrystals along the axis of the nanobranch. HRTEM studies displayed that the branches grew homoepitaxially as single-crystalline nanowires from the ZTO nanowire backbone. A possible growth model of the branched ZTO nanowires is discussed. To successfully prepare branched structures would provide an opportunity for both fundamental research and practical applications, such as three-dimensional nanoelectronics, and opto-electronic nanodevices.     

Porous ZnO nanobelts evolved from layered basic zinc acetate nanobelts

Novel porous ZnO nanobelts were successfully synthesized by heating layered basic zinc acetate (LBZA) nanobelts in the air. The precursor of LBZA nanobelts consisted of a lamellar structure with two interlayer distances of 1.325 and 0.99 nm were prepared using a low-temperature, solution-based method. X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and infrared spectroscopy are used to characterize the as-products. PL measurements show that the porous ZnO nanobelts have strong ultraviolet emission properties at 380 nm, while no defect-related visible emission is detected. The good performance for photoluminescence emission makes the porous ZnO nanobelts promising candidates for photonic and electronic device applications.     

The effects of substrate temperature on the structure, morphology and photoluminescence properties of pulsed laser deposited SrAl2O4:Eu,Dy thin films

In this study, SrAl₂O₄:Eu²⁺,Dy³⁺ thin film phosphors were deposited on Si (1 0 0) substrates using the pulsed laser deposition (PLD) technique. The films were deposited at different substrate temperatures in the range of 40-700 °C. The structure, morphology and topography of the films were determined by using X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). Photoluminescence (PL) data was collected in air at room temperature using a 325 nm He-Cd laser as an excitation source. The PL spectra of all the films were characterized by green phosphorescent photoluminescence at ∼530 nm. This emission was attributed to 4f⁶5d¹→4f⁷ transition of Eu²⁺. The highest PL intensity was observed from the films deposited at a substrate temperature of 400 °C. The effects of varying substrate temperature on the PL intensity were discussed.     

Synthesis and performance of core-shell structured ZnO/In2O3 composites in situ growth

Core-shell structured ZnO/In₂O₃ composites were successfully synthesized via situ growth method. Phase structure, morphology, microstructure and property of the products were investigated by X-ray diffraction (XRD), TG-DTA, field emission scanning electron microscopy (FESEM), energy-dispersive spectrometry (EDS), transmission electron microscope (TEM) and photoluminescence (PL). Results show that the core-shell structures consist of spindle-like ZnO with about 800 nm in length and 200 nm in diameter, and In₂O₃ particles with a diameter of 50 nm coated on the surface of ZnO uniformly. HMTA plays an important role in the formation of core-shell structures and the addition of In₂O₃ has a great effect on PL spectrum. Possible mechanism for the formation of core-shell structures is also proposed in this paper.     

Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.     

A facile and environmentally friendly chemical route for the synthesis of metastable VO2 nanobelts

Metastable VO₂ nanobelts, designated as VO₂ (B), were successfully fabricated by a facile hydrothermal route in the presence of V₂O₅ and glucose. The samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), transmission electron microscopy (TEM), selected area electronic diffraction (SAED), high-resolution transmission electron microscopy (HRTEM) and scanning electron microscopy (SEM) techniques. The main synthesis parameters such as temperature, reaction time and molar ratio of the starting materials have been also discussed. The results showed that pure B phase VO₂ nanobelts with high crystallinity can be prepared easily at 180 °C in 24 h at the molar ratio of V₂O₅:glucose=1:1. Typically, the belt-like products were 0.6-1.2 μm long, 80-150 nm wide and 20-30 nm thick. It is noted that the whole process is free of any harmful reducing reagents and surfactants, and valuable gluconic acid can be formed as the main by-product. From an economic and environmental point of view, the present approach is particularly fit for the synthesis of VO₂ (B) nanobelts on a large scale.     

Preparation, conversion, and comparison of the photocatalytic property of Cd(OH)2, CdO, CdS and CdSe

In this paper, we report the hydrothermal preparation of Cd(OH)₂ nanowires and further conversion to CdO nanobelts, CdS nanowires and CdSe nanoparticles through thermal treatment, solvothermal and mixed-solvothermal routes, respectively. The as-obtained products were characterized by means of powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and field emission scanning electron microscopy (FEMSEM). Research showed that four cadmium compounds were good photocatalysts for the degradation of organic dyes such as Safranine T and Pyronine B, under irradiation of 365 nm UV light. The order of catalytic activity of different materials was found to be Cd(OH)₂<CdO<CdS<CdSe.     

Fabrication,morphology and optical properties of GaN nanorods by ammoniating Ga2O3/Nb films

Wurtzite GaN nanorods have been successfully synthesized on Si(111) substrates through ammoniating Ga₂O₃/Nb films under flowing ammonia atmosphere at 950 ^°C in a quartz tube. The nanorods have been confirmed as hexagonal wurtzite GaN by X-ray diffraction (XRD) and selected-area electron diffraction (SAED). Scanning electron microscopy (SEM) and field-emission transmission electron microscope (FETEM) reveal that the nanorods are straight and uniform, with a diameter of ranging from 100 to 200 nm and lengths up to several microns. The photoluminescence spectra (PL) measured at room temperature only exhibit a strong emission peak at 368.5 nm. Finally, the growth mechanism of GaN nanorods is also briefly discussed.     

Preparation and properties of nanocrystalline powders in (Y1−xCex)3Al5O12 system

Nano-sized cerium-doped yttrium aluminum garnet (YAG:Ce) phosphors were synthesized via a simple sol-gel process using metal nitrate precursors. The prepared phosphors were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and photoluminescence (PL) spectroscopy, respectively. Pure cubic garnet phase was formed at temperatures ∼900 ^οC. The particle sizes of as-prepared powders were mostly in the range of 17-27 nm. The crystalline YAG:Ce showed broad emission peaks in the range of 400-700 nm and maximum intensities at 500 and 520 nm. It is found also that the emission intensity decreased with increasing Ce doping concentration from 0.1 to 1.5 at%. With increasing Ce doping concentration, the PL intensity was shifted towards shorter wavelengths.     

Disorder-dependent photoluminescence in Ba0.8Ca0.2TiO3 at room temperature

The photoluminescence (PL) emission in structurally disordered Ba_0.8Ca_0.2TiO₃ (BCT20) powders was observed at room temperature with laser excitation at lines 355 and 460 nm. The structural evolution perovskite-like titanate BCT20 powders prepared by a soft chemical processing at different annealing temperatures were accompanied by X-ray diffraction (XRD) and X-ray absorption near-edge structure (XANES). Intermediate oxycarbonate phase was identified and your influence with PL emission was discarding. BCT20 annealed at 500 °C displays intense PL emission. The results indicate relationship between broad PL band and order-disorder degree.     

Synthesis and luminescence properties of needle-like SrAl2O4:Eu, Dy phosphor via a hydrothermal co-precipitation method

Needle-like SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had been prepared by calcining the precursors obtained from hydrothermal process at the temperature of 1100 °C in a weak reductive atmosphere of active carbon. The crystal structure, morphology and optical properties of the composites were characterized. X-ray diffraction (XRD) patterns illustrated that the single-phase SrAl₂O₄ was formed at 1100 °C, which is much lower than that prepared by the traditional method. The transmission electron microscope (TEM) observation revealed the precursors and the resulted SrAl₂O₄:Eu²⁺, Dy³⁺ phosphors had well-dispersed distribution and needle-like morphology with an average diameter about 150 nm at the center and the length up to 1 μm. After irradiation by ultraviolet radiation with 350 nm for 5 min, the phosphors emit green color long-lasting phosphorescence corresponding to the typical emission of Eu²⁺ ion, both the PL spectra and luminance decay revealed that the phosphors had efficient luminescent and long lasting properties.     

Spherical Zn2SiO4:Eu@SiO2 phosphor particles in core-shell structure: Synthesis and characterization

Spherical SiO₂ particles have been coated with Zn₂SiO₄:Eu³⁺ phosphor layers by a Pechini sol-gel process. The microstructure and luminescent properties of the obtained Zn₂SiO₄:Eu³⁺@SiO₂ particles were well characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), photoluminescence (PL) spectra, and lifetime. The results demonstrate that the Zn₂SiO₄:Eu³⁺@SiO₂ particles, which have regular and uniform spherical morphology, emitted an intensive red light emission at 613 nm under excitation at 395 nm. Besides, the effects of the Eu³⁺ concentration, annealing temperature and charge compensators of Li⁺ ions on the PL emission intensities were investigated in detail.     

氧流量对热蒸发CVD法生长β-Ga2O3纳米材料的结构及发光特性的影响

用热蒸发CVD法制备了β-Ga₂O₃纳米材料, 并用光致发光(PL)方法研究了其发光特性. Ｘ射线衍射分析显示, 产物为单斜结构的β-Ga₂O₃. 扫描电子显微镜测试表明: 在较小氧流量条件下制备的产物为β-Ga₂O₃纳米带, 宽度小于100nm, 长度有几微米; 较大氧流量时制备出β-Ga₂O₃纳米晶粒结构, 晶粒尺度在80—15 关键词： 光致发光 氧流量 纳米结构 2O₃')" href="#">Ga₂O₃     

BaMoO4 powders processed in domestic microwave-hydrothermal: Synthesis, characterization and photoluminescence at room temperature

In this paper, BaMoO₄ powders were prepared by the coprecipitation method and processed in a domestic microwave-hydrothermal. The obtained powders were characterized by X-ray diffraction (XRD), Fourier transform Raman (FT-Raman) spectroscopy, ultraviolet-visible (UV-vis) absorption spectroscopy and photoluminescence (PL) measurements. The morphology of these powders were investigated by scanning electron microscopy (SEM). SEM micrographs showed that the BaMoO₄ powders present a polydisperse particle size distribution. XRD and FT-Raman analyses revealed that the BaMoO₄ powders are free of secondary phases and crystallize in a tetragonal structure. UV-vis was employed to determine the optical band gap of this material. PL measurements at room temperature exhibited a maximum emission around 542 nm (green emission) when excited with 488 nm wavelength. This PL behavior was attributed to the existence of intrinsic distortions into the [MoO₄] tetrahedron groups in the lattice.     

Synthesis and VUV spectral properties of nanoscaled Zn2SiO4:Mn green phosphor

Nanoscaled Zn₂SiO₄:Mn²⁺ green phosphor with regular and uniform morphology was synthesized by hydrothermal method at a low temperature of 140 °C. The structure and morphology of the phosphor was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of the hydrothermal temperature and the time on the crystallite structure and the vacuum ultraviolet (VUV) photoluminescence (PL) properties were evaluated. The as-synthesized nanoscaled Zn₂SiO₄:Mn²⁺ phosphor exhibited intensive broad emission around 523 nm, which was attributed to the ⁴T₁→⁶A₁ transition of Mn²⁺. The PL intensity increased along with the increasing hydrothermal temperature and time. The heat-treated phosphors exhibited higher PL intensity than the corresponding samples prepared using the conventional solid-state reaction.     

Elaboration and characterization of TiO2 nanoparticles incorporated in SiO2 host matrix

Nanometer-scale TiO₂ particles have been synthesized by sol-gel method. It was incorporated in a glass-based silica aerogel. The composite was characterized by various techniques such as particle size analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM), X-ray diffraction (XRD), infrared spectroscopy (IR) and photoluminescence (PL). The bulk glass presents a strong luminescence at wavelengths ranging from 750 to 950 nm. This PL was attributed to various non-bridging oxygen hole centers (NBOHCs) defects resulting from thermal treatment and crystallization of TiO₂ at the interface between titania nanoparticles and silica host matrix.     

Study of ZnO-coated SnO2 nanostructures synthesized by a two-step process

We investigated the influence of the ZnO coating on the properties of one-dimensional (1D) nanostructures of SnO₂. We have employed X-ray diffraction, scanning electron microscope, transmission electron microscope and photoluminescence (PL) spectroscopy to characterize both as-synthesized and ZnO-coated products. We observed that deposition process of ZnO by using an atomic layer deposition technique resulted in the SnO₂ core/ZnO shell structure. The photoluminescence of the ZnO-coated products exhibited broad bands in the UV and green region, suggesting a possible contribution of the emission from the ZnO outlayers.     

Synthesis of flower-shape clustering GaN nanorods by ammoniating Ga2O3 films

Flower-shape clustering GaN nanorods are successfully synthesized on Si（111） substrates through ammoniating Ga2O3/ZnO films at 950℃. The as-grown products are characterized by x-ray diffraction （XRD）, scanning electron microscope （SEM）, field-emission transmission electron microscope （FETEM）, Fourier transform infrared spectrum （FTIR） and fluorescence spectrophotometer. The SEM images demonstrate that the products consist of flower-shape clustering GaN nanorods. The XRD indicates that the reflections of the samples can be indexed to the hexagonal GaN phase and HRTEM shows that the nanorods are of pure hexagonal GaN single crystal. The photoluminescence （PL） spectrum indicates that the GaN nanorods have a good emission property. The growth mechanism is also briefly discussed.     

Highly luminescent red light phosphor CaTiO3:Eu under near-ultraviolet excitation

The Eu-doped CaTiO₃ particles with a good crystallinity were prepared via sol-gel method. The phosphors showed a strong red emission corresponding to ⁵D₀→⁷F₂ (618 nm) of Eu³⁺ under the near-ultraviolet excitation (400 nm). X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), photoluminescent (PL) analysis and Brunauer-Emmett-Teller (BET) specific surface area measurement were utilized to characterize the CaTiO₃:Eu³⁺ particles. The concentration quenching and thermal quenching of the samples were discussed as well. The optimal concentration and the calcination temperature were 16 mol% of Eu³⁺ and 1400 °C for these phosphors, and the possible reason was discussed as well. CaTiO₃:Eu³⁺ is a promising red phosphor under near-ultraviolet excitation for various applications.