Properties of vanadium-doped SrBi4Ti4O15 ferroelectric ceramics

Using the standard solid-state reaction method, several vanadium-doped ferroelectric ceramics of type SrBi_4−x/3Ti_4−xV_xO₁₅ (SBTV−x) were synthesized. The vanadium doping content, x, rangs from 0.00 to 0.06. The crystal structure of SrBi₄Ti₄O₁₅ is not affected by V-doping. The electric breakdown voltage of the samples increases with V content. Meanwhile, V-doping results in a notable enlargement of remnant polarization (2P_r). The 2P_r of STBV−0.03 reaches a very large value, which is over 50 μC/cm² and is nearly twice greater than that at zero doping. The Curie temperatures of V-doped samples decrease slightly in comparison with that of SrBi₄Ti₄O₁₅. V-doping can improve the electric properties of SrBi₄Ti₄O₁₅ without sacrificing its thermal stableness.     

Effects of vanadium doping on structure and electrical properties of SrBi4Ti4O15 thin films

The effects of vanadium(V) doping into SrBi₄Ti₄O₁₅ (SBTi) thin films on the structure, ferroelectric, leakage current, dielectric, and fatigue properties have been studied. X-ray diffraction result showed that the crystal structure of the SBTi thin films with and without vanadium is the same. Enhanced ferroelectricity was observed in the V-doped SrBi₄Ti₄O₁₅ (SrBi_4−x/3Ti_4−xV_xO₁₅, SBTiV-x (x = 0.03, 0.06, and 0.09)) thin films compared to the pure SrBi₄Ti₄O₁₅ thin film. The values of remnant polarization (2P_r) and coercive field (2E_c) of the SBTiV-0.09 thin film capacitor were 40.9 μC/cm² and 105.6 kV/cm at an applied electric field of 187.5 kV/cm, respectively. The 2P_r value is over five times larger than that of the pure SBTi thin film capacitor. At 100 kHz, the values of dielectric constant and dielectric loss were 449 and 0.04, and 214 and 0.06 for the SBTiV-0.09 and the pure SBTi thin film capacitors, respectively. The leakage current density of the SBTiV-0.09 thin film capacitor measured at 100 kV/cm was 6.8 × 10⁻⁹ A/cm², which is more than two and a half orders of magnitude lower than that of the pure SBTi thin film capacitor. Furthermore, the SBTiV-0.09 thin film exhibited good fatigue endurance up to 10¹⁰ switching cycles. The improved electrical properties may be related to the reduction of internal defects such as bismuth and oxygen vacancies with changes in the grain size by doping of vanadium into SBTi.     

La substitution in four-layers Aurivillius phase SrBi4Ti4O15

Ceramics with the nominal composition of SrBi_4−xLa_xTi₄O₁₅ have been prepared within the range of 0≤x≤1.8, and the dielectric properties are investigated. Single phase SrBi_4−xLa_xTi₄O₁₅ solid solution exists until the secondary phase of La_2/3TiO₃ appears at x=1.6. The Curie temperature is 520 °C for pure SrBi₄Ti₄O₁₅, and it shifts to low temperature with increasing x, which is due to the smaller structural distortion caused by La³⁺ substitution. In addition, the dielectric constant anomaly is suppressed with the substitution. No dielectric relaxation behavior is observed. When x≥1.2, the paraelectric state is attained in the present ceramics. La³⁺ substitution effects on the SrBi₄Ti₄O₁₅ ceramics are also compared with the previous work on Bi_4−xLa_xTi₃O₁₂.     

Electrical properties of neodymium doped CaBi4Ti4O15 ceramics

Neodymium doped bismuth layer structure ferroelectrics (BLSFs) ceramics CaBi_4−xNd_xTi₄O₁₅ (x=0, 0.25, 0.50, 0.75) were prepared by solid-state reaction method. X-ray diffraction pattern showed that single phase was formed when x=0-0.75. The refined lattice parameters showed that a (b) axes decrease at x=0.25 and increase with more Nd³⁺ dopant. The effects of Nd³⁺ doping on the dielectric and ferroelectric properties of CaBi₄Ti₄O₁₅ ceramics are studied. Nd³⁺ dopant decreased the Curie temperature linearly, and the dielectric loss, tan δ, as well. The remnant polarization of Nd³⁺ doped CaBi₄Ti₄O₁₅ ceramics was increased by 80% at x=0.25, while more Nd³⁺ dopant decreased the remnant polarization. CaBi_3.75Nd_0.25Ti₄O₁₅ ceramics had the largest piezoelectric constant d₃₃. The structure and properties of CaBi_4−xNd_xTi₄O₁₅ ceramics showed that Nd³⁺ may occupy different crystal locations when Nd³⁺ content x is less than 0.25 and more than 0.50.     

Mo掺杂SrBi4Ti4O15陶瓷的铁电介电性能

用传统的固相烧结工艺，制备了钼掺杂铁电陶瓷样品SrBi₄Ti₄O₁₅(SBTi)铁电陶瓷SrBi_4-2x/3Ti_4-xMo_xO₁₅(x=0.00，0.003，0.012，0.03，0.06，0.09).X射线衍射的结果表明，样品均为单一的层状钙钛矿结构相，Mo掺杂未改变SBTi的晶体结构.通过扫描电子显微镜观测发现，样品晶粒为片状，随掺杂量的增加，晶粒逐 关键词： 4Ti₄O₁₅')" href="#">SrBi₄Ti₄O₁₅ Mo掺杂 剩余极化 居里温度     

Ferroelectric properties of Bi3.25−x/3La0.75Ti3−xNbxO12 films prepared by pulsed laser deposition

Bi₄Ti₃O₁₂ (BiT), Bi_3.25La_0.75Ti₃O₁₂ (BLT), Bi_4−x/3Ti_3−xNb_xO₁₂ (BTN) and Bi_3.25−x/3La_0.75Ti_3−xNb_xO₁₂ (BLTN) thin films have been prepared by pulsed laser deposition. BTN and BLTN films exhibit a maximum in the remanent polarization P_r at a Nb content x=0.018. At this Nb content, the BLTN film has a P_r value (25 μC/cm²) that is much higher than that of BiT and a coercive field similar to that of BiT. The polarization of this BLTN film is fatigue-free up to 10⁹ switching cycles. The high fatigue resistance is mainly due to the substitution of Bi³⁺ ions by La³⁺ ions at the A site and the enhanced P_r arises largely from the replacement of Ti⁴⁺ ions by Nb⁵⁺ ions at the B site. The mechanisms behind the effects of the substitution at the two sites are discussed.     

(Bi,La)4Ti3O12-Sr(Bi,La)4Ti4O15共生结构铁电材料性能研究

采用固相烧结工艺，制备了不同La掺杂量(x=0.00，0.25，0.50，0.75，1.00，1.25和1.50) 的(Bi, La)₄Ti₃O₁₂-Sr(Bi, La)₄Ti4O₁₅ (SrBi_8-xLa_xT i₇O₂₇)共生结构铁电陶瓷样品.用x射线衍射对其进行微结构分析 ，并测量铁 关键词： 4Ti₃O₁₂-SrBi₄Ti₄O₁₅')" href="#">Bi₄Ti₃O₁₂-SrBi₄Ti_{4O15 La掺杂 铁电性能 居里温度 弛豫铁电}     

La掺杂SrBi4Ti4O15铁电材料性能研究

按x=0.00，0.10，0.25，0.50，0.75和1.00，采用固相烧结工艺，制备了不同La掺杂量的SrBi_4-xLa_xTi₄O₁₅的陶瓷样品. 用x射线衍射对其微结构进行了分析，并测量了铁电、介电性能.结果发现，La掺杂未改变SrBi₄Ti ₄O₁₅的晶体结构.随掺杂量的增加，样品的矫顽场(E_c)下降，剩余极化(2P_{关键词： 4-x}La_xTi₄O₁₅')" href="#">SrBi_4-xLa_xTi₄O₁₅ La掺杂 铁电性能 相变温度 弛豫铁电     

Great enhancement in remnant polarization of SrBi4Ti4O15 thin films by A-site doping of Fe3+ ions

SrBi4-xFexTi4O15 (SBFT-x) thin films (x = 0.00, 0.05, 0.08, 0.15) have been synthesized on Pt/Ti/SiO2/Si (100) substrates by sol-gel method. This paper finds that Fe-doping does not change the crystal structure of SrBi4Ti4O15 (SBTi). The coercive filed (Ec) and remnant polarisation (Pr) increase at first, then decrease with the increase of Fe doping content. At a maximum applied field of 229 kV/cm, the 2Pr reaches a maximum value of 91.1 μC/cm2 at x = 0.05 and the corresponding Ec is 72 kV/cm. The 2Pr increases by about 260% and the Ec decreases by about 6%, respectively. Obviously, the ferroelectric property of SrBi4Ti4O15 is greatly enhanced by Fe doping. The fatigue-endurance characteristic of the SBFT-0.05 is not improved. After 1.1×109 read/write cycles at a frequency of 50 kHz, the nonvolatile polarisations (Pnv = P*-P∧) decreased about 48% of its initial value.     

Compositional dependence of ferroelectric properties of highly c-axis oriented Bi4−xNdxTi3O12 film capacitors

Highly c-axis oriented neodymium-modified bismuth titanate (Bi_4−xNd_xTi₃O₁₂) films having a variety of neodymium (Nd) contents were successfully grown on Pt/TiO₂/SiO₂/Si(100) substrates using metal-organic sol decomposition. After systematically examining ferroelectric properties of the c-axis oriented Bi_4−xNd_xTi₃O₁₂ film capacitors as a function of the Nd-content, we concluded that the capacitor with x=0.85 had the largest remanent polarization. The Bi_3.15Nd_0.85Ti₃O₁₂ capacitor fabricated using a top Pt electrode showed well-saturated polarization-electric field (P-E) switching curves with the remanent polarization (P_r) of 51 μC/cm² and the coercive field (E_c) of 99 kV/cm at an applied voltage of 10 V. More importantly, the Pt/Bi_3.15Nd_0.85Ti₃O₁₂/Pt capacitor exhibited fatigue-free behavior up to 4.5×10¹⁰ read/write switching cycles at a frequency of 1 MHz. The capacitor also demonstrated an excellent charge-retaining ability and a strong resistance against the imprinting failure.     

Ferroelectric properties of highly c-axis oriented Bi4−xLaxTi3O12 film-based capacitors

Highly c-axis oriented lanthanum-modified bismuth titanate (Bi_4−xLa_xTi₃O₁₂) films having a variety of lanthanum (La) contents were grown on Pt/TiO₂/SiO₂/Si(100) substrates using metal-organic sol deposition and subsequent annealing at 650 °C for 1 h. After systematically examining the ferroelectric properties of Bi_4−xLa_xTi₃O₁₂ films as a function of the La-content, it was concluded that the film with x=0.85 had the largest remanent polarization in the direction parallel to the c-axis. The Pt/Bi_3.15La_0.85Ti₃O₁₂/Pt capacitor showed a well-saturated polarization-electric field (P-E) switching curve with the switching remanent polarization (2P_r) value of 33 μC/cm² and the coercive field (E_c) of 68 kV/cm at an applied voltage of 10 V. More importantly, the capacitor exhibited fatigue-free behavior up to 6.5×10¹⁰ read/write switching cycles at a frequency of 1 MHz. The capacitor also demonstrated an excellent charge-retaining ability and a strong resistance against the imprinting failure.     

Dielectric and piezoelectric properties of lead-free (Na0.5K0.5)NbO3-SrTiO3 ceramics

In this article, we report successful preparation of dense [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ (x=0.005-0.100) ceramics by ordinary sintering in air. The dependence of phase structure on doping content of SrO and TiO₂ has been determined by the X-ray diffraction technique. It was found that the crystal structure changed from orthorhombic to tetragonal at x≈0.040. Dielectric study revealed that the dielectric relaxor behavior was induced by doping of SrO and TiO₂ into (Na_0.5K_0.5)NbO₃. The samples in the composition range from x=0.005 to 0.020 exhibited excellent electrical properties, piezoelectric constant of electromechanical planar and thickness coupling coefficients of k_p=26.6-32.5% and k_t=39.8-43.8%. The results show that the [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics are one of the promising lead-free materials for electromechanical transducer applications.     

Ferroelectric and dielectric properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> thin films grown on Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> film layer

Ferroelectric and dielectric properties of bilayered ferroelectric thin films, SrBi₄Ti₄O₁₅ grown on Bi₄Ti₃O₁₂, were investigated. The thin films were annealed at 700°C under oxygen atmosphere. The bilayered thin films were prepared on a Pt(111)/Ti/SiO₂/Si substrate by a chemical solution deposition method. The dielectric constant and dielectric loss of the bilayered thin films were 645 and 0.09, respectively, at 100 kHz. The value of remnant polarization (2P _r) measured from the ferroelectric thin film capacitors was 60.5 μC/cm² at electric field of 200 kV/cm. The remnant polarization was reduced by 22% of the initial value after 10¹⁰ switching cycles. The results showed that the ferroelectric and dielectric properties of the SrBi₄Ti₄O₁₅ on Bi₄Ti₃O₁₂ ferroelectric thin films were better than those of the SrBi₄Ti₄O₁₅ grown on a Pt-coated Si substrate suggesting that the improved properties may be due to the different nucleation and growth kinetics of SrBi₄Ti₄O₁₅ on the c-axis-oriented Bi₄Ti₃O₁₂ layer or on the Pt-coated Si substrate.     

Dielectric properties of lanthanum-doped CaCu3Ti4O12 synthesized by semi-wet route

Effect of La³⁺ doping at Ca²⁺ site in CaCu₃Ti₄O₁₂ has been examined. Compositions with x=0.10, 0.20 and 0.30 were synthesized in the system Ca_(1−3x/2)La_xCu₃Ti₄O₁₂ by semi-wet method. Powder X-ray diffraction confirmed the formation of monophasic compounds. The structure remains cubic similar to CaCu₃Ti₄O₁₂. Lattice parameter increases slightly with increasing La³⁺ concentration. Microstructure has been studied using scanning electron microscopy (SEM). Average grain size is in the range 2-4 μm for various compositions. Energy-dispersive spectrometer (EDS) studies confirm the stoichiometry of the synthesized materials. Dielectric constant, dielectric loss and conductivity of the samples decrease with increasing lanthanum concentrations.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Ferroelectric properties of Pr6O11-doped Bi4Ti3O12

Praseodymium doped Bi₄Ti₃O₁₂ (BIT) ceramics with composition Bi_2.9Pr_0.9Ti₃O₁₂ (BPT) were prepared by solid state reaction. These samples have polycrystalline Bi-layered perovskite structure without preferred orientation, and consist of well-developed plate-like grains with random orientation. Pr doping into BIT causes a large shift of the Curie temperature (T_C) of the BIT from 675 to 398 °C. At an electric field of 87 kV/cm, the remanent polarization and the coercive field of the BPT ceramics are 30 μC/cm² and 52 kV/cm, respectively. Furthermore, the dielectric permittivity and the dissipation factor of the BPT ceramics are 300 and 0.003 at 1 MHz, 1 V, and room temperature. Ferroelectric properties of the BPT ceramics are superior to V-doped Bi₄Ti₃O₁₂ (∼20 μC/cm² and 80 kV/cm) and (Sr, Ta)-doped Bi₄Ti₃O₁₂ (∼12 μC/cm² and 71 kV/cm) ceramics. In addition, the dense ceramics of praseodymium-doped B₄Ti₃O₁₂ were obtained by sintering at 1100 °C, about 100-200 °C lower than those of the SrBi₂Ta₂O₉ system.     

Structural distortion and phase transition studies of Aurivillius type Sr1−xPbxBi2Nb2O9 ferroelectric ceramics

In this paper, effects of lead doping on the lattice response and phase transitions of Sr_1−xPb_xBi₂Nb₂O₉ (x=0.0-0.5 in steps of 0.1) ferroelectric ceramics are reported. It is observed that structure attains more tetragonality with doping of lead up to 40%. Increased orthorhombic distortion is observed for undoped SBN and 50 at.% lead substituted SBN. Phase transitions for all samples were studied using Curie temperature measurements and are explained in terms of lattice response of these ceramics. Sample with x=0.5 shows decreased tetragonal strain and Curie temperature. Relationship of polarization with lattice response is discussed.     

Effect of electric field on electrocaloric effect in Pb(Zr1 − xTix)O3 solid solution

A thermodynamic analysis is employed to investigate the intrinsic electrocaloric effect of Pb(Zr_1 − xTi_x)O₃ solid solution system under the different electric field. Theoretical analysis indicates that Pb(Zr_1 − xTi_x)O₃ system has the giant electrocaloric coefficient and the large adiabatic temperature change near its ferroelectric Curie temperature. The applied electric field decreases not only the electrocaloric coefficient but also its temperature dependence. Furthermore, it increases the adiabatic temperature change as well as its dependence of temperature. The temperature corresponding to the maximum of electrocaloric coefficient and adiabatic temperature change increases with the enhancement of electric field because of its first-order phase transition between ferroelectric phase and paraelectric phase.     

Effects of composition on phase structure and electrical properties of (K0.5Na0.5)0.90Li0.06Sr0.02Nb(1−x)SbxO3 ceramics

Lead-free (K_0.5Na_0.5)_0.90Li_0.06Sr_0.02Nb_(1−x)Sb_xO₃ (KNLSN-Sb_x) ceramics were synthesized by ordinary sintering technique. The compositional dependence of phase structure and electrical properties of the ceramics was systematically investigated. All samples possessed pure perovskite structure, showing room temperature symmetries of orthorhombic at x<0.01, coexistence of orthorhombic and tetragonal phases at x=0.01, and tetragonal at 0.02≤x≤0.05. The temperature of the polymorphic phase transition (PPT) was shifted to lower temperature and dielectric relaxor behavior was induced by increasing Sb content. The samples near the coexistence region (x=0.01) exhibited enhanced electrical properties: d₃₃∼145 pC/N, k_p∼38% and P_r∼20.4 μC/cm².     

Dielectric properties of SrBi2−xPrxNb2O9 ceramics (x=0, 0.04 and 0.2)

SrBi_2−xPr_xNb₂O₉ (x=0, 0.04 and 0.2) ceramics were prepared by a solid state reaction method. X-ray diffraction analysis indicated that single-phase layered perovskite structure ferroelectrics were obtained. A relaxor behavior of frequency dispersion was observed among Pr-doped SrBi₂Nb₂O₉. The degree of frequency dispersion ΔT increased from 0 for x=0-7 °C for x=0.2, and the extent of relaxor behavior γ increased from 0.94 for x=0-1.45 for x=0.2. The substitution of Pr ions for Bi³⁺ ions in the Bi₂O₂ layers resulted in a shift of the Curie point to lower temperatures and a decrease in remanent polarization. In addition, the coercive field 2E_c reduced from 110 kV/cm for an undoped specimen to 90 kV/cm for x=0.2.