Electrical properties of high Curie temperature (1−x)Pb(In1/2Nb1/2)O3-xPbTiO3 single crystals grown by the solution Bridgman technique

0.65Pb(In_1/2Nb_1/2)O₃-0.35PbTiO₃ (PINT65/35) (starting composition) single crystals were grown successfully through the solution Bridgman technique using PbO flux and PMNT67/33 seed crystals. Because of the composition variation, the final composition of achievable crystals is in a range of 0.32-0.34 with the corresponding T_c range of 265-269 °C. The (001) plates of as-grown PINT66/34 single crystals show high Curie temperature (T_c=269 °C) and rhombohedral-tetragonal phase transition temperature (T_rt=134 °C). Besides, good electrical properties with high dielectric constant (ε>3000), low dielectric loss (tan δ∼1.2%), high piezoelectric constant (d₃₃∼2000 pC/N) and large electromechanical coupling factor (k_t≈59%) at room temperature have been obtained on the (001) plates. The sound velocity, acoustic impedance and other piezoelectric parameters were also measured on the (001) plates in this study, which provide us more detailed information about PINT66/34 single crystals.     

Electro-optic characterization of tetragonal (1−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals by a modified Sénarmont setup

The refractive indices of tetragonal (1−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMN-xPT) single crystals were measured with a prism coupler and their linear electro-optic (EO) properties were investigated from 20 to 80 °C by the automated scanning Sénarmont system with an ac field. The composition and temperature effect on the EO coefficients were also discussed. It has been found that their EO coefficients are much larger than that of widely used LiNbO₃ single crystal and the calculated half-wave voltages are also much lower, which enable the operation at lower voltages and the smaller device dimensions. Since the excellent EO properties are very stable and such high quality single crystals with large-size have been obtained, the PMN-xPT single crystals are a very promising candidate for EO modulation applications. By linking to the polarization-related quadratic EO coefficients, we find that the linear EO properties are related with the spontaneous polarization and dielectric constants.     

Influence of 90° domain switching on the physical properties of tetragonal barium titanate single crystals

In this paper, we report the influence of 90° domain switching on the physical properties of tetragonal BaTiO₃ single crystals. It is found that the contribution of 90° domain switching to the piezoelectric response is much larger in magnitude than the contribution of the direct piezoelectric effect under large external mechanical stress. Simultaneously, the interconversion of a and c crystallographic axes and the large actuation strain as high as 1% is induced by 90° domain switching in the tetragonal BaTiO₃ single crystal.     

Investigation on optical transmission spectra of (1−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals

The optical transmission spectra from 0.3 to 11 μm of relaxor ferroelectric single crystals (1−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMN-xPT) were systematically studied at room temperature in this paper. The crystal is transparent between 0.45 and 5.5 μm and becomes completely absorbing around 0.4 μm in near UV region and 10 μm in infrared region. But the wavelength cutoff in near UV is much sharper than the long wavelength cutoff. As compared with other configurations, tetragonal single crystals possess the optimal transmission properties. The optical transmittance in the wavelength region from 0.45 to 5.5 μm is about 70%. The results show that tetragonal PMN-xPT single crystals are promising for a wide range of optical applications. Some discussions about the oxygen-octahedra structure that determines the basic energy level of the crystals are also presented on the optical properties of PMN-xPT single crystals.     

Growth of high performance piezoelectric crystal Pb(Zn1/3Nb2/3)O3-PbTiO3 using PbO flux

Novel piezoelectric crystal (1 − x)Pb(Zn_1/3Nb_2/3)O₃-xPbTiO₃ (PZNT) has attracted much attention due to its high piezoelectric properties and potential applications in medical ultrasonic devices, sonar transducers, solid state actuators. However, the applications of PZNT crystals are limited by the lack of a simple and reproducible growth technique. In this work, large size PZNT crystals were grown by the vertical Bridgman method using 50 mol% PbO as a flux. The growth conditions were optimized as mole ratio of raw materials and flux = 1:1, soaking temperature 1150-1200 °C, soaking time 10 h, the lowering rate of the crucible 0.5 mm/h and the temperature gradient near solid-liquid interface about 50 °C/mm. The maximum size of as-grown PZNT crystal was about 60 mm in length. The crystal was oriented and its piezoelectric constant d₃₃ and coupling coefficient k₃₃ were measured over 2000 pC/N and 0.92, respectively.     

Characterization of lead free (K0.5Na0.5)NbO3-LiSbO3 piezoceramic

(K_0.5Na_0.5)NbO₃ (KNN) based lead free ceramics have been fabricated by a solid state reaction. In this work, LiSbO₃ (LS) modified KNN based ceramics were sintered at atmospheric pressure and high density (>96% theoretical) was obtained. The detailed elastic, dielectric, piezoelectric and electromechanical properties were characterized by using the resonance technique combined with the ultrasonic method. The full set of material constants for the obtained polycrystalline ceramics were determined and compared to the pure hot pressed KNN counterpart. KNN-LS polycrystalline ceramic was found to have higher elastic compliance, dielectric permittivity and piezoelectric strain coefficients, but lower mechanical quality factor, when compared to pure KNN, exhibiting a “softening” behavior. However, a high coercive field (∼17 kV/cm) was found for the LS modified KNN material. The properties as a function of temperature were determined in the range of −50-250 ^°C, showing a polymorphic phase transition near room temperature, giving rise to improved piezoelectric behavior.     

Phase transformation in (0.90−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3-0.10PbZrO3 piezoelectric ceramic: X-ray diffraction and Raman investigation

Piezoelectric ceramics with compositions of (0.90−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃-0.10PbZrO₃, x=0.28, 0.31, 0.34, 0.37, 0.40 and 0.43, were prepared using the conventional columbite precursor method, and their structural phase transformation and piezoelectric behaviors near the morphotropic phase boundary (MPB) have been systematically investigated as a function of PbTiO₃ content. X-ray diffraction (XRD) results demonstrate that the structure of the ceramics experiences a gradual transition process from rhombohedral phase to tetragonal phase with the increasing of PbTiO₃ content, and that compositions with x=0.34-0.40 lie in the MPB region of this ternary system. A Raman spectra investigation of the ceramic samples testified to the transformation process of rhombohedral phase to tetragonal phase by comparing the relative intensities of tetragonal E(2TO₁) mode and rhombohedral phase R_h mode. The structure information was also correlated to the parabola change of the piezoelectric constant; the maximum piezoelectric constants were obtained near the MPB region.     

Ferroelectric properties of Pr6O11-doped Bi4Ti3O12

Praseodymium doped Bi₄Ti₃O₁₂ (BIT) ceramics with composition Bi_2.9Pr_0.9Ti₃O₁₂ (BPT) were prepared by solid state reaction. These samples have polycrystalline Bi-layered perovskite structure without preferred orientation, and consist of well-developed plate-like grains with random orientation. Pr doping into BIT causes a large shift of the Curie temperature (T_C) of the BIT from 675 to 398 °C. At an electric field of 87 kV/cm, the remanent polarization and the coercive field of the BPT ceramics are 30 μC/cm² and 52 kV/cm, respectively. Furthermore, the dielectric permittivity and the dissipation factor of the BPT ceramics are 300 and 0.003 at 1 MHz, 1 V, and room temperature. Ferroelectric properties of the BPT ceramics are superior to V-doped Bi₄Ti₃O₁₂ (∼20 μC/cm² and 80 kV/cm) and (Sr, Ta)-doped Bi₄Ti₃O₁₂ (∼12 μC/cm² and 71 kV/cm) ceramics. In addition, the dense ceramics of praseodymium-doped B₄Ti₃O₁₂ were obtained by sintering at 1100 °C, about 100-200 °C lower than those of the SrBi₂Ta₂O₉ system.     

Bias field effects on the dielectric properties of 0.67Pb(Mg1/3Nb2/3)O3-0.33PbTiO3 single crystals with different orientations

The domain states and phase transitions in 0.67Pb(Mg_1/3Nb_2/3)O₃-0.33PbTiO₃ single crystals were investigated by studying their relative permittivity under various dc bias at constant heating and cooling rates. The orientation dependence of the bias field effect was revealed by examining the temperature dependence of relative permittivity as a function of crystal orientation (the 〈111〉, 〈011〉 and 〈001〉 directions) and dc bias field. The crystals basically have a macrodomain rhombohedral ferroelectric state in the ferroelectric phase under zero dc bias. External bias field could modulate the domain state and induce a stable macrodomain state in the crystals. Also, it is proposed that the dc bias applied along the 〈001〉 or 〈011〉 direction could induce a tetragonal ferroelectric phase or an orthorhombic ferroelectric phase, respectively, in an intermediate temperature range.     

Domain structures in tetragonal Pb(Mg1/3Nb2/3)O3-PbTiO3 single crystals studied by piezoresponse force microscopy

The domain structures in (001) surface of Pb(Mg_1/3Nb_2/3)O₃-40% PbTiO₃ single crystals were investigated by piezoresponse force microscopy. Both micron-sized fingerprint 180° and parallel 90° domains were observed in the sample. Different sets of favourable {110} oriented domain patterns were found to meet, intersect or grow through each other. In addition, the piezoelectricity decreases sharply at the domain walls in 180° structures, but does not in the 90° domain structures.     

Influence of niobium doping on the electrical properties of 0.58Pb(Sc1/2Nb1/2)O3-0.42PbTiO3 single crystal

Piezoelectric single crystals of 0.58Pb(Sc_1/2Nb_1/2)-0.42PbTiO₃ and Nb⁵⁺-doped PSN-PT have been grown using flux technique. It is believed that the addition of Nb⁵⁺ creates lead vacancy in order to compensate charge neutrality. The structural distortion that occured in the doped crystals has been revealed through broadening of some peaks in X-ray diffraction studies. Niobium content that increased from 0.50 to 1.00 mol% might have induced more defect dipoles associated with . This plays a significant role in improving the ferroelectric, dielectric and piezoelectric properties. Our observations clearly show an increase in the spontaneous polarization (P_r), dielectric constant at room temperature, degree of diffuseness and transition temperature (T_c) and also a decrease in coercive field. The reasons behind these enhanced electrical properties are discussed in detail.     

（Na0.52K0.44Li0.04）Nb0.9-xSbxTa0.1O3 Lead-Free Piezoelectric Ceramics with High Performance and High Curie Temperature

（Na0.52K0.44Li0.04）Nb0.9-x Sbx Ta0.1O3 lead-free piezoelectric ceramics are prepared by a solid-state reaction method. With increasing Sb content, the transition temperature from orthorhombic to tetragonal polymorphic phase decreased. A composition （Na0.52K0.44Li0.04）Nb0.863Sb0.037Ta0.1O3 is found to possess excellent piezo- electric and electromechanical performances （d33 = 306pC/N, kp =48%, and kt=50%）, and high Curie temperature （Tc = 320 ℃）. These results indicate that （Na0.52K0.44Li0.04）Nb0.863Sb0.037 Ta0.1O3 is a promising lead-free piezoceramics replacement for lead zirconate titanate.     

Comparative study of K0.5Bi0.5TiO3 nanoparticles derived from sol-gel-hydrothermal and sol-gel routes

A kind of novel lead-free ferroelectrics, potassium bismuth titanate, K_0.5Bi_0.5TiO₃ (KBT), has been prepared by sol-gel-hydrothermal and sol-gel routes, respectively, and the structural characters of as-synthesized powders were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The results indicated that sol-gel-hydrothermal route led to the formation of KBT nanowhiskers with diameters of 20 nm and lengths of 1 μm, and the processing temperature was as low as 160 °C, but the normal sol-gel route tended to form KBT cubic particles of about 100-200 nm, and the processing temperature was higher than 700 °C. It is believed that the gel precursor and hydrothermal environment play an important role in the formation of the nanowhiskers at low temperature. Due to the good sinterability of nanowhiskers, the ferroelectric and dielectric properties of KBT ceramics prepared by sol-gel-hydrothermal route were super to that prepared by sol-gel route.     

Role of the TiO6 octahedra on the ferroelectric and piezoelectric behaviour of the poled PbMg1/3Nb2/3O3-xPbTiO3 (PMN-PT) single crystal and textured ceramic

Field cooling (FC) poled/unpoled PMN-29%PT single crystal and room temperature (RT) poled/unpoled PMN-34.5%PT textured ceramic were investigated between ∼0 and 300 °C by thermal expansion, dielectric and Raman spectroscopy. New phase transitions are evidenced at 40, 91 and 180 °C in the case of FC PMN-29%PT as well as at 70 and 200 °C for RT PMN-34.5%PT and their order is discussed. The physical properties of the textured ceramics are rather similar to the ones observed for the single crystals that make them low-cost alternative for a wide range of applications. However, the temperatures and character of the phase transitions strongly depend on the kind of the poling conditions. Temperature dependences of the Raman line parameters show that the NbO₆ octahedra remain stable during temperature increase, while TiO₆ ones evolve quasi-continuously. The step transitions of the Pb²⁺ ion sublattice are evidenced. This suggests that the TiO₆ and Pb²⁺ sublattices are especially coupled. The role of the TiO₆ clusters on the structural phase transitions and dielectric properties of the PbMg_1/3Nb_2/3O₃-xPbTiO₃ (PMN-PT) system is discussed. The presence of the Raman modes above the maximum dielectric permittivity reveals that the local symmetry is lower than the cubic one (Pm3m). The decrease of the Raman line intensities vs. temperature indicates precisely the continuous evolution of the local symmetry towards the cubic one. The temperature evolution of the Rayleigh wing parameters appears sensitive to the phase transitions’ presence.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

Electromechanical properties and dielectric behavior of (Bi1/2Na1/2)(1−1.5x)BixTiO3 lead-free piezoelectric ceramics

Bismuth doped bismuth sodium titanate ceramics [(Bi_1/2Na_1/2)_(1−1.5x)Bi_xTiO₃, x=0 to 0.06] were prepared, and the resulting effects on the microstructure and dielectric properties were examined. All of the Bi-doped ceramics exhibited a single phase of perovskite structure with rhombohedral symmetry. The poling leakage current was significantly reduced by the doping of Bi, facilitating the poling process of the ceramics. The doping with Bi enhances the piezoelectric properties and increases the dielectric constant and the dielectric loss of the ceramics. At 2 mol% Bi-doping level, the ceramics exhibit a large remanent polarization of 47 μC/cm² and a relatively low coercive field of 71 kV/cm, while their d₃₃ and k_p reach a maximum value of 95 pC/N and 21%, respectively.     

Effects of composition on phase structure and electrical properties of (K0.5Na0.5)0.90Li0.06Sr0.02Nb(1−x)SbxO3 ceramics

Lead-free (K_0.5Na_0.5)_0.90Li_0.06Sr_0.02Nb_(1−x)Sb_xO₃ (KNLSN-Sb_x) ceramics were synthesized by ordinary sintering technique. The compositional dependence of phase structure and electrical properties of the ceramics was systematically investigated. All samples possessed pure perovskite structure, showing room temperature symmetries of orthorhombic at x<0.01, coexistence of orthorhombic and tetragonal phases at x=0.01, and tetragonal at 0.02≤x≤0.05. The temperature of the polymorphic phase transition (PPT) was shifted to lower temperature and dielectric relaxor behavior was induced by increasing Sb content. The samples near the coexistence region (x=0.01) exhibited enhanced electrical properties: d₃₃∼145 pC/N, k_p∼38% and P_r∼20.4 μC/cm².     

Crystal growth and dielectric, piezoelectric and elastic properties of Ca3TaGa3Si2O14 single crystal

Single crystals of Ca₃TaGa₃Si₂O₁₄ (CTGS) were successfully grown from stoichiometric melts by the conventional Czochralski technique. The relative dielectric constants, the piezoelectric strain constants and the elastic compliance constants of CTGS single crystal have been determined by an electric bridge and resonance-antiresonance method. At room temperature, the two piezoelectric strain constants d₁₁ and d₁₄ are −4.58×10⁻¹² coulombs per newton (C/N) and 10.43×10⁻¹² coulombs per newton (C/N), respectively. The velocities of the bulk acoustic wave are also calculated.     

Na0.5K0.5NbO3-BiFeO3 lead-free piezoelectric ceramics

Lead-free (Na_0.5K_0.5)NbO₃-based piezoelectric ceramics were successfully fabricated by substituting with a small amount of BiFeO₃ (BF). Difficulty in sintering of pure NKN ceramics can be eased by adding a few molar percent of BF, and the crystalline structure is also changed, leading to a morphotropic phase boundary (MPB) between ferroelectric orthorhombic and rhombohedral phases. The MPB exists near the 1-2 mol% BF-substituted NKN compositions, exhibiting enhanced ferroelectric, piezoelectric, and electromechanical properties of P_r=23.3 μC/cm², d₃₃=185 pC/N, and k_p=46%, compared to an ordinarily sintered pure NKN ceramics. The MPB composition has a Curie temperature of ∼370 °C, comparable to that of some commercial PZT materials.     

Effects of Interfacial Polarization on Voltage Tunability of Pb(Fe1/2Nb1/2)1-xTixO3 Single Crystals

The voltage tunability of Pb(Fe_1/2Nb_1/2)_1-xTi_xO₃ single crystals is investigated at a low electric field (<130 V/cm) in a low frequency range (<1 MHz). The results show that the capacitance is strongly suppressed by the applied dc biases for both the rhombohedral sample and the tetragonal sample. A negative voltage tunability is only detected in the tetragonal sample. The origin of the giant tunability and the negative tunability is discussed based on the multipolarization-mechanism model and the equivalent circuit model, respectively. It is ascribed to the interfacial polarization at the interface of electrode/sample.