X-ray diffraction study of molybdenum diselenide to 35.9 GPa

In situ high-pressure angle dispersive synchrotron X-ray diffraction studies of molybdenum diselenide (MoSe₂) were carried out in a diamond-anvil cell to 35.9 GPa. No evidence of a phase transformation was observed in the pressure range. By fitting the pressure-volume data to the third-order Birch-Murnaghan equation of state, the bulk modulus, K_0T, was determined to be 45.7±0.3 GPa with its pressure derivative, K′_0T, being 11.6±0.1. It was found that the c-axis decreased linearly with pressure at a slope of −0.1593 when pressures were lower than 10 GPa. It showed different linear decrease with the slope of a −0.0236 at pressures higher than 10 GPa.     

Compression behavior of nanocrystalline anatase TiO2

We present a synchrotron X-ray diffraction study of pressure-induced changes in nanocrystalline anatase (with a crystallite size of 30-40 nm) to 35 GPa. The nanoanatase was observed to a pressure above 20 GPa. Direct transformation to the baddeleyite-TiO₂ polymorph was seen at 18 GPa. A fit of the pressure versus volume data to a Birch-Murnaghan equation yielded the following parameters: zero-pressure volume, V₀=136.15 Å³, bulk modulus, K_T=243(3) GPa, and the pressure derivative of bulk modulus, K′=4 (fixed). The bulk modulus value obtained for the nanocrystalline anatase is about 35% larger than that of the macrocrystalline counterpart.     

Structural and thermodynamic properties of WB at high pressure and high temperature

The structure parameters and electronic structures of tungsten boride (WB) have been investigated by using the density functional theory (DFT). Our calculating results display the bulk modulus of WB are 352±2 GPa (K′₀=4.29) and 322±3 GPa (K′₀=4.21) by LDA and GGA methods, respectively. We have analyzed the probable reason of the discrepancy from the bulk modulus between theoretical and experimental results. The compression behavior of the unit cell axes is anisotropic, with the c-axis being more compressible than the a-axis. By analyzing the bond lengths information, it also demonstrated that WB has a lower compressibility at high pressure. From the partial densities of states (PDOS) of WB, we found that the Fermi lever is mostly contributed by the d states of W atom and p states of B atom and that the contributions from the s, p states of W atom and s states of B atom are small. Moreover, using the Gibbs 2 program, the thermodynamic properties of WB are obtained in a wide temperature range at high pressure for the first time in this work.     

Equation of state of aluminum carbide Al4C3

Quasi-hydrostatic compression of aluminum carbide, Al₄C₃ has been studied to 6 GPa at room temperature using energy-dispersive X-ray powder diffraction with synchrotron radiation. A fit of the experimental p-V data to the Birch equation of state yields the values of the bulk modulus, B₀, of 130(5) GPa and the first pressure derivative of the bulk modulus, B′₀, of 4.6(9). The compression is found to be anisotropic, with the a-axis being more compressible than the c-axis.     

High-pressure X-ray diffraction study of tungsten diselenide

Synchrotron X-ray diffraction was used in conjunction with a diamond anvil cell to investigate the properties of a tungsten diselenide (WSe₂) sample to 35.8 GPa at room temperature. By fitting the pressure-volume data to the third-order Birch-Murnaghan equation of state, the bulk modulus, K_0T, of WSe₂ was determined to be 72±1 GPa with its pressure derivative, , being 4.1±0.1. It was also found that the c-direction of the hexagonal structure is significantly more compressible than the a-direction. No phase transformation was clearly observed in the pressure range of our measurements.     

High pressure X-ray diffraction study of ReS2

The high-pressure behavior of rhenium disulfide (ReS₂) has been investigated to 51.0 GPa by in situ synchrotron X-ray diffraction in a diamond anvil cell at room temperature. The results demonstrate that the ReS₂ triclinic phase is stable up to 11.3 GPa, at which pressure the ReS₂ transforms to a new high-pressure phase, which is tentatively identified with a hexagonal lattice in space group P6?m2. The high-pressure phase is stable up to the highest pressure in this study (51.0 GPa) and not quenchable upon decompression to ambient pressure. The compressibility of the triclinic phase exhibits anisotropy, meaning that it is more compressive along interlayer directions than intralayer directions, which demonstrates the properties of the weak interlayer van der Waals interactions and the strong intralayer covalent bonds. The largest change in the unit cell angles with increasing pressures is the increase of β, which indicates a rotation of the sulfur atoms around the rhenium atoms during the compression. Fitting the experimental data of the triclinic phase to the third-order Birch-Murnaghan EOS yields a bulk modulus of K_OT=23±4 GPa with its pressure derivative K_OT′= 29±8, and the second-order yields K_OT=49±3 GPa.     

Single-crystal elastic constants of magnesium difluoride (MgF2) to 7.4 GPa

The six independent elastic constants (C₁₁, C₁₂, C₁₃, C₃₃, C₄₄, and C₆₆) of single-crystal MgF₂ in the rutile structure have been measured by Brillouin spectroscopy at room temperature from ambient conditions to 7.4 GPa. Measurements were performed on two monocrystals with perpendicular faces, (001) and (100). A quasi-linear fit from finite strain theory was applied to the experimental data revealing the pressure dependence of the six elastic constants of MgF₂. The shear modulus C_S=1/2(C₁₁−C₁₂), and the aggregate shear (Voigt–Reuss–Hill) modulus G show a softening with increasing pressure, indicating the approach of the rutile-to-CaCl₂-type structural phase transition at P~9 GPa. The adiabatic bulk modulus (Reuss average) and its pressure derivative have been determined: K_0S=105.1±0.3 GPa, (∂K_0S/∂P)_T=4.14±0.05. The pressure–volume equation of state of MgF₂ was computed self-consistently from the Brillouin data. Our results are in good agreement with X-ray diffraction data. As the phase transition is approached, MgF₂ becomes strongly anisotropic and develops partially auxetic behavior (a negative Poisson's ratio in certain directions).     

Thermal equation-of-state of osmium: a synchrotron X-ray diffraction study

The pressure-volume-temperature behavior of osmium was studied at pressures and temperatures up to 15 GPa and 1273 K. In situ measurements were conducted using energy-dispersive synchrotron X-ray diffraction in a T-cup 6-8 high pressure apparatus. A fit of room-temperature data by the third-order Birch-Murnaghan equation-of-state yielded isothermal bulk modulus K₀=435(19) GPa and its pressure derivative K′₀=3.5(0.8) GPa. High-temperature data were analyzed using Birch-Murnaghan equation of state and thermal pressure approach. The temperature derivative of bulk modulus was found to be −0.061(9) GPa K⁻¹. Significant anisotropy of osmium compressibility was observed.     

High pressure X-ray diffraction study on icosahedral boron arsenide (B12As2)

The high pressure properties of icosahedral boron arsenide (B₁₂As₂) were studied by in situ X-ray diffraction measurements at pressures up to 25.5 GPa at room temperature. B₁₂As₂ retains its rhombohedral structure; no phase transition was observed in the pressure range. The bulk modulus was determined to be 216 GPa with the pressure derivative 2.2. Anisotropy was observed in the compressibility of B₁₂As₂—c-axis was 16.2% more compressible than a-axis. The boron icosahedron plays a dominant role in the compressibility of boron-rich compounds.     

Elasticity of single-crystal phase D (a dense hydrous magnesium silicate) by Brillouin spectroscopy

Phase D (MgSi₂O₆H₂) is the only hydrous magnesium silicate, where all Si atoms are octahedrally coordinated. The single-crystal elastic constants of phase D have been measured by Brillouin spectroscopy at ambient conditions. The elastic constants C₁₁, C₃₃, C₄₄, C₁₂, C₁₃ and C₁₄, based on a trigonal unit cell, are 284.4±3.0, 339.4±9.1, 120.7±1.9, 89.4±4.2, 126.6±3.1 and −4.7±1.4 GPa, respectively. The aggregate adiabatic bulk modulus, using the Voigt-Reuss-Hill (VRH) scheme, is 175.3±14.8 GPa and the shear modulus is 104.4±13.6 GPa. These data yield the compressional-wave velocity, V_p=9.70±0.51 km/s, and the shear-wave velocity, V_s=5.59±0.36 km/s, at ambient conditions. Thus, phase D is not only the most closely packed but the least compressible hydrous magnesium silicate known to date.     

Compression behavior of the delafossite-type metallic oxide PdCoO2 below 10 GPa

The compression behavior of delafossite-type metallic oxide PdCoO₂ below 10 GPa has been investigated by in situ high pressure X-ray diffraction measurement using synchrotron radiation. It is found that the delafossite-type structure of PdCoO₂ is stable below 10 GPa. It should be noted that compression behavior of PdCoO₂ is anisotropic. Pressure dependence of the lattice parameters indicates that the a-axis is more compressible than the c-axis. The lattice parameter ratio c/a in the hexagonal unit increases with increasing pressure. The calculated zero-pressure bulk modulus is 224 GPa. It is found that the above characteristic compression behaviors of PdCoO₂ are the same as those of the delafossite CuFeO₂. The compressibilities of the a-axis of both PdCoO₂ and CuFeO₂ are highly different although those of the c-axis are almost the same.     

High-pressure powder diffraction study of TaO2F

TaO₂F, with a ReO₃-type structure, has been studied at up to 12.8 GPa using monochromatic synchrotron powder diffraction and diamond anvil cells. Two-phase transitions at ∼0.7 and 4 GPa were observed on compression. Below ∼0.7 GPa the cubic material was found to have a bulk modulus (K₀) of 36(3) GPa (K_p fixed at 4.0), similar to that reported for NbO₂F but much smaller than that of ReO₃. Immediately above 0.7 GPa on compression, the diffraction data were not fully consistent with a VF₃-type structure as previously proposed for NbO₂F. On decompression, the data between 8 and 4 GPa could be satisfactorily attributed to a single R-3c phase with a VF₃-type structure and an average bulk modulus of 60(2) GPa.     

Equation of state of silicon nitride carbodiimide Si2CN4

The lattice parameters of silicon nitride carbodiimide Si₂CN₄ have been measured up to 8 GPa at room temperature using energy-dispersive X-ray powder diffraction with synchrotron radiation. A fit of the experimental p-V data to the Birch-Murnaghan equation of state yields the values of the bulk modulus of 8.8(2) GPa and its first pressure derivative of 3.4(1). The compression is found to be anisotropic, with the b-axis being significantly more compressible than the a-and c-axes.     

Elastic, thermal and structural properties of platinum

The thermal equation of state (EOS) for platinum has been calculated to 300 GPa and 3000 K using ab initio molecular dynamics employing the local density approximation (LDA) and the projector augmented-wave methods (PAW). Direct ab initio molecular dynamics avoids the simplifying assumptions inherent in empirical treatments of thermoelasticity. A third-order Birch-Murnaghan equation EOS fitted to the 300 K data yielded an isothermal bulk modulus of B_T0=290.8 GPa and a pressure derivative of B_T′=5.11, which are in better agreement with the measured values than those obtained by previous calculations. The high-temperature data were fitted to a thermal pressure EOS and a Mie-Grüneisen-Debye EOS. The resulting calculated thermal expansion coefficient, α₀, temperature derivative of the isothermal bulk modulus, (∂B_T/∂T)_V, and second temperature derivative of the pressure, (∂²P/∂T²)_V, were 1.94×10⁻⁵ K⁻¹, −0.0038 GPa K⁻¹, and 1.7×10⁻⁷ GPa² K⁻², respectively. A fit to the Mie-Grüneisen-Debye EOS yielded values for the Grüneisen parameter, γ₀, and its volume dependence parameter, q, of 2.18 and 1.75, respectively. An analysis of our data revealed a strong volume dependence of the thermal pressure of platinum. We also present a qualitative analysis of the effects of intrinsic anharmonicity from the calculated Grüneisen parameter at high temperatures.     

Structural studies of AgSbTe2 under pressure: Experimental and theoretical analyses

The crystal structure of AgSbTe₂ has been refined using first-principles calculations, from which the ordering of the cations, Ag and Sb, was confirmed. The spontaneous formation of two (D4 and L1₁) phases at ambient and elevated pressure was demonstrated theoretically. The compound was also prepared and its high-pressure structural deformation sequence, ranging from ambient to 50.9 GPa, was observed with synchrotron radiation at room temperature. The compound underwent a pressure-induced amorphization (PIA) at 24.6 GPa and then started recrystallizing at 49.2 GPa. The bulk modulus (B₀) and pressure derivative of the bulk modulus (B_p) were determined experimentally to be 56.3 ± 5.1 GPa and 4.3 ± 0.8, respectively. We suggest that large displacements of Te atoms to Ag vacancy positions are responsible for PIA and the recrystallization.     

Compression of CdCu3Ti4O12 perovskite to 55 GPa

Synchrotron x-ray diffraction measurements of CdCu₃Ti₄O₁₂ (CDCTO) were performed up to 55.5 GPa. There is no structural phase transformation in this pressure range. The irregular curvature shifts of the P-V curve are attributed to the grain surface effect. Analysis indicates that the grain surface of CDCTO is stiffer than the grain interior at higher pressures. We point out that the atoms on grain surfaces must be either densely packed or have a strong correlation with the gain interior in order to have a high dielectric constant, as in CaCu₃Ti₄O₁₂. The derived bulk modulus of CDCTO is approximately 235±7 GPa with K^′=5.1±0.4.     

Structure and high pressure behaviour of organic crystals based on aromatically substituted 1,3,4-oxadiazoles

The crystalline structure of a new compound containing the 1,3,4-oxadiazole moiety, 4-(5-methyl-1,3,4-oxadiazole-2yl-)-N,N′-dimethyl-phenylamine (MODPA) was determined. It shows a monoclinic structure with space group P2₁/c and lattice parameters: a=1.02997(6), b=0.64840(4), c=1.58117(10) nm and β=99.4820(10)°. To study the intermolecular interactions in oxadiazole containing organic crystals, X-ray studies on MODPA and 2,5-diphenyl-1,3,4-oxadiazole (DPO) were performed up to 5 GPa at room temperature. The Murnaghan equation of state is used to describe the compression behaviour of both substances. From these results, the bulk modulus and its pressure derivative were determined. The values obtained are: K₀=6.3 GPa and K′₀=6.8 for MODPA and K₀=7.3 GPa and K′₀=6.7 for DPO. Additionally, measurements under increasing temperature at ambient pressure were carried out to evaluate the thermal expansion coefficient: α=1.8×10⁻⁴ K⁻¹ for MODPA and α=1.9×10⁻⁴ K⁻¹ for DPO.     

Theoretical study of the structural, elastic, electronic and thermal properties of the MAX phase Nb2SiC

Structural, elastic, electronic and thermal properties of the MAX phase Nb₂SiC are studied by means of a pseudo-potential plane-wave method based on the density functional theory. The optimized zero pressure geometrical parameters are in good agreement with the available theoretical data. The effect of high pressure, up to 40 GPa, on the lattice constants shows that the contractions along the c-axis were higher than those along the a-axis. The elastic constants C_ij and elastic wave velocities are calculated for monocrystal Nb₂SiC. Numerical estimations of the bulk modulus, shear modulus, Young’s modulus, Poisson’s ratio, average sound velocity and Debye temperature for ideal polycrystalline Nb₂SiC aggregates are performed in the framework of the Voigt-Reuss-Hill approximation. The band structure shows that Nb₂SiC is an electrical conductor. The analysis of the atomic site projected densities and the charge density distribution shows that the bonding is of covalent-ionic nature with the presence of metallic character. The density of states at Fermi level is dictated by the niobium d states; Si element has a little effect. Thermal effects on some macroscopic properties of Nb₂SiC are predicted using the quasi-harmonic Debye model, in which the lattice vibrations are taken into account. The variations of the primitive cell volume, volume expansion coefficient, bulk modulus, heat capacity and Debye temperature with pressure and temperature in the ranges of 0-40 GPa and 0-2000 K are obtained successfully.     

In situ observations of temperature- and pressure-induced phase transitions in TiH2: Angle-dispersive and synchrotron energy-dispersive X-ray diffraction studies

We investigated the behavior of the structure of titanium hydride (TiH₂), an important compound in hydrogen storage research, at elevated temperatures (0-120 °C) and high pressures (1 bar-34 GPa). Temperature-induced changes of TiH₂ as indicated in the alteration of the ambient X-ray demonstrated a cubic to tetragonal phase transition occurring at about 17 °C. The main focus of this study was to identify any pressure-induced structural transformations, including possible phase transitions, in TiH₂. Synchrotron X-ray diffraction studies were carried out in situ (diamond anvil cell) in a compression sequence up to 34 GPa and in subsequent decompression to ambient pressure. The pressure evolution of the diffraction patterns revealed a cubic (Fm-3m) to tetragonal (I4/mmm) phase transition at 2.2 GPa. The high-pressure phase persisted up to 34 GPa. After decompression to ambient conditions the observed phase transition was completely reversible. A Birch-Murnaghan fit of the unit cell volume as a function of pressure yielded a zero-pressure bulk modulus K₀=146(14) GPa, and its pressure derivative K′₀=6(1) for the high-pressure tetragonal phase of TiH₂.     

X-ray diffraction and Raman spectra of merrillite at high pressures

ABSTRACT

The compressibility and effect of pressure on the vibrations of merrillite, Ca₉NaMg(PO₄)₇, were studied by using diamond anvil cell at room temperature combined with in-situ synchrotron X-ray diffraction and Raman spectroscopy up to about 18 and 15?GPa, respectively. The pressure-volume data was fitted by a third-order Birch–Murnaghan equation of state to determine the isothermal bulk modulus as K₀ ?=?87.2(32) GPa with pressure derivative K₀′?=?3.2(4). If K₀′?=?4, the isothermal bulk modulus was obtained as 81.6(10) GPa. The axial compressibility was estimated and an axial elastic anisotropy exists since a-axis is less compressible than the c-axis. The Raman frequencies of all observed modes for merrillite continuously increase with pressure, and the pressure dependences of stretching modes (v ₃ and v ₁) are larger than those of the bending modes (v ₄ and v ₂) and external modes. The isothermal mode Grüneisen parameters and intrinsic anharmonicity of merrillite were also calculated.