Fabrication of rubrene nanowires on vicinal (0 0 0 1) sapphire surfaces

Morphology of high-vacuum deposited rubrene thin films on the annealed (0 0 0 1) vicinal sapphire surfaces was studied by atomic force microscopy in non-contact mode. Atomic force microscopy images of rubrene thin films indicate that a regular array of steps on the sapphire surface acts as a template for the growth of the arrays of rubrene nanosize wires. To further demonstrate that morphological features of a substrate are crucial in determining the morphology of rubrene layers we have grown rubrene on the sapphire surfaces that were characterized by the terrace-and-step morphology with islands. We have found preferential nucleation of rubrene molecules at the intersection between a terrace and a step, as well as around the islands located on terraces.     

Growth and characterization of thin PTCDA films on 3C-SiC(0 0 1)c(2 × 2)

The growth of thin 3,4,9,10-perylene tetracarboxylic dianhydride (PTCDA) films on a 3C-SiC(0 0 1)c(2 × 2) substrate has been studied by means of photoelectron spectroscopy (PES) and atomic force microscopy (AFM). In the first monolayer the molecules interact with the substrate mainly through the O atoms in the end groups of the molecule. The O atoms have a higher binding energy in the first molecular layer compared to the following layers. No chemical shifts are observed in the Si 2p spectra or in the C 1s spectra from the perylene core of the molecules. From the VB spectra and LEED pattern we conclude that the substrate remains in the c(2 × 2) reconstruction after PTCDA deposition. For thicker films a Stranski-Krastanov film growth was observed with flat lying molecules relative to the substrate.     

Silicon carbide nanocrystals growth on Si(1 0 0) and Si(1 1 1) from a chemisorbed methanol layer

SiC nanocrystals are grown at high temperature on Si(1 0 0) and Si(1 1 1) surfaces starting from a chemisorbed layer of methanol. The decomposition of this layer allows to have a well defined amount of carbon to feed SiC growth. Nanocrystals ranging from 10 nm to 50 nm with density from 100 μm⁻² to 1500 μm⁻² are obtained, and the total volume of produced SiC corresponds to carbon provided by the chemisorbed organic layer. Large differences in nanocrystal size and density, as well as in surface roughness, are observed depending on substrate orientation. The internal structure, crystallinity and epitaxy of nanocrystals grown on Si(1 0 0) are studied using cross-sectional transmission electron microscopy (XTEM), methanol adsorption and surface evolution using scanning tunnelling microscopy (STM). The joint application of XTEM and STM techniques allows a complete characterization of the geometry and chemical composition of these nanostructures.     

Heterogeneous oxidation of Si(1 1 1) 7 × 7 monitored with Kelvin probe force microscopy

Laterally resolved topography and Contact Potential Difference (CPD) images, acquired during the exposure of clean Si(1 1 1) 7 × 7 to molecular oxygen at room temperature, show a heterogeneous oxidation process, without preference for step edges. The increase of and lateral changes in work function variations show that the CPD variations of the final oxide film are related to the silicon/oxide interface. The molecular Höfer precursor has a pronounced influence on the development of the interface bonding.     

Strain state in bcc Fe films grown on Si(1 1 1)

The strain state of Fe films grown on Si(1 1 1) has been investigated by X-ray diffraction (XRD) in the thickness range between 11 and 304 monolayers. Fe grows tetragonally distorted with the orientation relationship Fe(1 1 1) // Si(1 1 1) . At low coverage, the films grow pseudomorphic. Above 15 monolayers the films are characterized by the coexistence of a pseudomorphic phase with another one which relaxes with the Fe thickness. This relaxation proceeds rapidly in the earlier stages then slowly with the film thickness. The XRD characterization allows one to obtain quantitative information on the in-plane and out-of-plane strains.     

Growth mechanisms for wire-like epitaxial gold silicide islands on Si(1 1 0) surfaces

Epitaxial islands grown on various substrates are usually strained because of differences in lattice constants of the materials of the island and the substrate. Shape transition in the growth of strained islands has been proposed as a mechanism for strain relief and a way to form self-organized quantum wires. Shape transition usually leads to an elongated island growth. However, an elongated island growth may also be due to an anisotropic diffusion of material, the anisotropy being imposed by the symmetry of the substrate surface. In the present example, growth of gold silicide wire-like nanostructures on a Si(1 1 0) surface has been investigated by photoemission electron microscopy (PEEM). Growth of elongated unidirectional gold silicide islands, with an aspect ratio as large as 12:1, has been observed by PEEM following gold deposition on the Si substrate and subsequent annealing at the Au-Si eutectic temperature. Distribution of the width and the length of the gold silicide islands as a function of island area shows a feature similar to that for the shape transition. However, detailed investigations reveal that the elongated growth of gold silicide islands is rather mainly due to anisotropic diffusion of gold due to the twofold symmetry of the (1 1 0) surface of the Si substrate.     

Metastable precursor for oxygen dissociation on Si(0 0 1) 2 × 1 resolved by high lateral resolution work function measurements

The development of contact potential difference (CPD) inhomogeneities on oxide-covered silicon samples was investigated by monitoring the CPD of a clean Si(0 0 1) 2 × 1 surface during exposure to molecular oxygen with Kelvin Probe Force Microscopy. A steady fluctuation level is reached within the completion of a monolayer of oxide. Non-continuous oxygen exposure at room temperature and at lower temperatures unequivocally demonstrates the coexistence of two oxidation processes. One of these processes involves a metastable precursor to oxygen dissociation.     

Tuning the geometry of shape-restricted DNA molecules on the functionalized Si(1 1 1)

Designing a well-defined and stable interface between biomolecules and semiconductor surfaces is of great importance for current and future biosensing and bioelectronic applications. The well-characterized chemistry, stability, and easily tunable electronic properties of silicon substrate make it a practical platform for this type of interface. It has been established in our previous work that a robust, covalent attachment between thiol-DNA molecules of a pre-designed geometrical shape and a modified silicon surface can be achieved. This work focuses on using this binding model and altering the distance between the DNA molecules and silicon surface by strategically placing thiol linkers within the pre-determined geometric design of the rectangularly shaped DNA. The statistical analysis of the height profiles of DNA molecules attached to the surface, as determined by AFM, provides specific insight into how the construction of the DNA molecules affects the binding distance. A comparison between two thiol-DNA molecules with different numbers of thiol groups placed either within the rectangular shape or anchored to the free loop of the same geometric design suggest that the average distance of these molecules to the functionalized silicon surface can be changed by approximately 0.5 nm.     

Growth of PTCDA crystals on H:Si(1 1 1) surfaces

The room temperature deposition of PTCDA on hydrogen passivated Si(1 1 1), as a function of evaporation temperature and dosing time, has been studied by STM. At low evaporation temperature, 200 °C, clusters with an average size of 3.5 nm are formed on the surface. The mobility of the small clusters is so high, even at room temperature, that most of the clusters are trapped at surface defects. By increasing the evaporation temperature to 230 °C, larger clusters are formed which have lower mobility. The growth process is identified as a Volmer-Weber mechanism. On increasing the evaporation temperature further to 250 °C, crystals with dendritic shape are formed with an average size of 150 nm. The terraces of the crystal are formed with the (1 0 2) basal plane of the α-phase. Molecular resolution on the terrace also allows us to identify the molecular mechanism involved in the growth of the dendritic crystals.     

Bimodal growth of manganese silicide on Si(1 0 0)

Two different growth modes of manganese silicide are observed on Si(1 0 0) with scanning tunneling microscopy. 1.0 and 1.5 monolayer Mn are deposited at room temperature on the Si(1 0 0)-(2 × 1) substrate. The as-grown Mn film is unstructured. Annealing temperatures between room temperature and 450 °C lead to small unstructured clusters of Mn or Mn_xSi_y. Upon annealing at 450 °C and 480 °C, Mn reacts chemically with the Si substrate and forms silicide islands. The dimer rows of the substrate become visible again. Two distinct island shapes are found and identified as MnSi and Mn₅Si₃.     

Signatures of epitaxial graphene grown on Si-terminated 6H-SiC (0 0 0 1)

Epitaxial graphene layers thermally grown on Si-terminated 6H-SiC (0 0 0 1) have been probed using Auger electron spectroscopy, Raman microspectroscopy, and scanning tunneling microscopy (STM). The average multilayer graphene thickness is determined by attenuation of the Si (L₂₃VV) and C (KVV) Auger electron signals. Systematic changes in the Raman spectra are observed as the film thickness increases from one to three layers. The most striking observation is a large increase in the intensity of the Raman 2D-band (overtone of the D-band and also known as the G′-band) for samples with a mean thickness of more than ∼1.5 graphene layers. Correlating this information with STM images, we show that the first graphene layer imaged by STM produces very little 2D intensity, but the second imaged layer shows a single-Lorentzian 2D peak near 2750 cm⁻¹, similar to spectra acquired from single-layer micromechanically cleaved graphene (CG). The 4-10 cm⁻¹ higher frequency shift of the G peak relative to CG can be associated with charge exchange with the underlying SiC substrate and the formation of finite size domains of graphene. The much greater (41-50 cm⁻¹) blue shift observed for the 2D-band may be correlated with these domains and compressive strain.     

Site selective atomic chlorine adsorption on the Si(1 1 1)7 × 7 surface

The spontaneous dissociation of trichloroethylene molecules on the Si(1 1 1)7 × 7 surface was investigated using STM. Chlorine atoms were identified by using voltage dependent imaging and by observing voltage dependent tip-induced diffusion. At low coverage, we identify one chlorine that dissociates and binds to an adatom, leaving a nearby chlorovinyl group as the other product bound to the surface. Chlorine atoms show strong site selectivity for corner adatoms and some preference for the faulted half of the unit cell. This result differs significantly from previous studies of chlorine on this surface and a site-selective mobile precursor model is used to explain this discrepancy. The observed site-selectivity is consistent with the high electronegativity value for chlorine.     

Thin PTCDA films on Si(0 0 1): 1. Growth mode

We have studied the interface and thin film formation of the organic molecular semiconductor 3,4,9,10 perylene tetracarboxylic dianhydride (PTCDA) on clean and on hydrogen passivated Si(0 0 1) surfaces. The studies were made by means of high resolution X-ray photoelectron spectroscopy (HRXPS), near edge X-ray absorption fine structure (NEXAFS), low energy electron diffraction (LEED), and atomic force microscopy (AFM). On the passivated surface the LEED pattern is somewhat diffuse but reveals that the molecules grow in several ordered domains with equivalent orientations to the substrate. NEXAFS shows that the molecules are lying flat on the substrate. The Si 2p XPS line shape is not affected when the film is deposited so it can be concluded that the interaction at the interface between PTCDA and the substrate is weak. The evolution of the film formation appears to be homogeneous for the first monolayer with a nearly complete coverage of flat lying molecules based on the XPS attenuation. For layer thickness of 0.5-2 monolayers (ML) the molecules start to form islands, attracting the molecules in between, leaving the substrate partly uncovered. For thicker films there is a Stranski-Krastanov growth mode with thick islands and a monolayer thick film in between. For the clean surface the ordering of the film is much lower and angle resolved photoelectron spectroscopy (ARPES) of the molecular orbitals have only a small dependence of the emission angle. NEXAFS shows that the molecules do not lie flat on the surface and also reveal a chemical interaction at the interface.     

Si(1 1 1)-H(1 × 1): A mirror for atoms characterized by AFM, STM, He and H2 diffraction

AFM, STM and diffraction of He and H₂ have been used to assess Si(1 1 1)-H(1 × 1) surfaces for their potential as mirrors for matter-waves. The H-passivated samples are produced by wet-chemical methods and delivered to a different laboratory for diffraction measurements. We show that the surface is flat and homogenous over lateral scales of microns and that absolute He and H₂ reflectivities of the order of ∼3% are obtained, even after 20 h storage under Ar and several days’ storage in UHV. These characteristics allow the use of Si(1 1 1)-H(1 × 1) as a highly reflective mirror for atoms and molecules, with application in a future He microscope or focused hydrogen nano-lithography system.     

Formation of oxygen-induced Si(1 1 3)-3 × 2 facets on the Si(5 5 12) surface

We report the formation of Si(1 1 3)-3 × 2 facets upon exposing oxygens on the Si(5 5 12) surface at an elevated temperature. These facets are found to form only for a limited range of oxygen exposure and exhibit a well-defined 3 × 2 LEED pattern. We also find the surface electronic state unique only to the facets in the valence band. The spectral feature of these electronic states and the behavior of a (1/3 1/2) LEED spot upon oxygen contents in the facets indicate that the formation is a heterogeneous mixture of the clean Si(1 1 3) facets free of oxygens and other facets containing oxygen atoms.     

Fabrication of uniform Au silicide islands on the Si(1 1 1)-(7 × 7) substrate

The Au silicide islands have been fabricated by additional deposition of Au on the prepared surface at 270 °C where the Si islands of magic sizes were formed on the Si(1 1 1)-(7 × 7) dimer-adatom-stacking fault substrate. The surface structure on the Au silicide islands shows the Au/Si(1 1 1)-√3 × √3 reconstructed structure although the substrate remains 7 × 7 DAS structure. The size of the Au silicide islands depends on the size distribution of the preformed Si islands, because the initial size and shape of the Si islands play important roles in the formation of the Au silicide island. We have achieved the fabrication of the Au silicide islands of about the same size (∼5 nm) and the same shape by controlling the initial Si growth and the additional Au growth conditions.     

Evidence for diffusion-limited kinetics during electromigration-induced step bunching on Si(1 1 1)

We have measured how the initial terrace width l₀ on vicinal Si(1 1 1) surfaces influences the rate of step bunching and the minimum terrace width within a bunch when direct-current heated at 940-1290 °C. A comparison of this data with analytic solutions and numerical simulations of the conventional “sharp-step” model give strong evidence that the kinetic length d is relatively small (d < ∼20 nm) in both temperature regime I (∼850-950 °C) and regime III (∼1200-1300 °C), in which step-down current is required for step bunching. This indicates that surface mass transport is diffusion-limited in both regimes I and III when l₀ > 20 nm, and hence that the adatom attachment- and terrace diffusion-hopping rates are of comparable magnitude. We also observe similar scaling with initial terrace width in temperature regime II (∼1040-1190 °C), in which step-up current is required for bunching, suggesting a similar step bunching mechanism in all three temperature regimes.     

Following the oxidation of yttrium silicide epitaxially grown on Si(1 1 1) by core level photoemission spectroscopy

We have identified, by means of synchrotron radiation X-ray photoemission spectroscopy, several core-level shifted components in the Si-2p photoemission core level peak from a thin yttrium silicide layer epitaxially grown on a Si(1 1 1) surface. We have unequivocally assigned these components to different environments of the Si atoms in the silicide structure. This information has been used to monitor a surface oxidation process promoted by room temperature oxygen adsorption, identifying the final product of this reaction as a silicate-type ternary compound.     

Co growth on Si(0 0 1) and Si(1 1 1) surfaces: Interfacial interaction and growth dynamics

In situ X-ray photoelectron spectroscopy (XPS) and ex situ atomic force microscopy (AFM) were used to study the growth of thin cobalt films at room temperature (RT) on both clean and H-terminated Si(0 0 1) and Si(1 1 1) surfaces. The growth proceeds by first forming an initial CoSi₂-like phase at the growth front of the Si substrate. With increasing Co coverage the interfacial layer composition becomes richer in Co and eventually a metallic Co film is formed on top. Hydrogen termination of the Si surface did not suppress the reaction of Co and Si. A pseudo-layer-by-layer growth mode is proposed to describe the growth of Co on H-terminated Si surfaces, while closed-packed small island growth occurs on clean Si surfaces. The difference in growth mode can be attributed to the increase in the surface mobility of Co adatoms in the presence of hydrogen.     

The epitaxial sexiphenyl (0 0 1) monolayer on TiO2(1 1 0): A grazing incidence X-ray diffraction study

A para-sexiphenyl monolayer of near up-right standing molecules (nominal thickness of 30 Å) is investigated in-situ by X-ray diffraction using synchrotron radiation and ex-situ by atomic force microscopy. A terrace like morphology is observed, the step height between the terraces is approximately one molecular length. The monolayer terraces, larger than 20 μm in size, are extended along the [0 0 1] direction of the TiO₂(1 1 0) substrate i.e. along the Ti-O rows of the reconstructed substrate surface. The structure of the monolayer and its epitaxial relationship to the substrate is determined by grazing incidence X-ray diffraction. Extremely sharp diffraction peaks reveal high crystalline order within the monolayer, which was found to have the bulk structure of sexiphenyl. The monolayer terraces are epitaxially oriented with the (0 0 1) plane parallel to the substrate surface (out-of-plane order). Four epitaxial relationships are observed. This in-plane alignment is determined by the arrangement of the terminal phenyl rings of the sexiphenyl molecules parallel to the oxygen rows of the substrate.