类金刚石和碳氮薄膜的电化学沉积及其场发射性能研究

利用电化学方法在室温下成功地沉积了类金刚石(DLC)薄膜和非晶CN_x薄膜，并 对制备条件进行了讨论.通过扫描电子显微镜、傅里叶变换红外光谱技术，分析了薄膜的表面形貌和化学结合状态.场发射测量结果表明：DLC膜和非晶CN_x的开启场分别为88和 10V/μm；并且在23V/μm的电场下，DLC膜和非晶CN_x膜的发射电流密度分别达到10 和037mA/cm². 关键词： 电化学沉积 类金刚石薄膜 x薄膜')" href="#">CN_x薄膜 场致电子发射     

ZnO纳米薄膜的电化学制备及其AFM形貌表征

利用恒电位电化学沉积方法在ITO导电玻璃基底上制备了纳米ZnO薄膜,并利用原子力显微镜进行了形貌表征。结果显示,当沉积电压为-0．8V时,经过30min的沉积在基底上形成了由规则排列的三角形ZnO晶粒构成的纳米薄膜。对晶粒的形成机理进行了初步的讨论。     

液相电化学法制备类金刚石薄膜及其摩擦性能研究

采用自行设计的液相法沉积装置,以甲醇有机溶剂作为碳源,利用液相电化学沉积技术在不锈钢及Si基底上制备了类金刚石薄膜;用扫描电镜、Raman光谱仪表征了沉积薄膜的表面形貌和结构;用UMT-2M摩擦磨损试验机对两种沉积薄膜进行了摩擦性能测试。结果表明：经电化学沉积的类金刚石薄膜均匀、致密,表面粗糙度小;Raman光谱在1332 cm-1处有强的谱峰,与金刚石的特征峰相吻合,其中不锈钢基底上薄膜的sp3含量更高;不锈钢基底沉积膜的摩擦系数为0.12,Si片基底沉积膜的摩擦系数为0.10;不锈钢基底沉积膜的耐磨性较Si片沉积膜高。     

液相电化学法制备类金刚石薄膜及其摩擦性能研究

采用自行设计的液相法沉积装置,以甲醇有机溶剂作为碳源,利用液相电化学沉积技术在不锈钢及Si基底上制备了类金刚石薄膜;用扫描电镜、Raman光谱仪表征了沉积薄膜的表面形貌和结构;用UMT-2M摩擦磨损试验机对两种沉积薄膜进行了摩擦性能测试。结果表明:经电化学沉积的类金刚石薄膜均匀、致密,表面粗糙度小;Raman光谱在1 332cm-1处有强的谱峰,与金刚石的特征峰相吻合,其中不锈钢基底上薄膜的sp3含量更高;不锈钢基底沉积膜的摩擦系数为0.12,Si片基底沉积膜的摩擦系数为0.10;不锈钢基底沉积膜的耐磨性较Si片沉积膜高。     

退火对B掺杂纳米金刚石薄膜微结构和电化学性能的影响

采用热丝化学气相沉积法制备B掺杂纳米金刚石薄膜,并对薄膜进行真空退火处理,系统研究了不同退火温度对B掺杂纳米金刚石薄膜的微结构和电化学性能的影响.结果表明,当退火温度升高到800 ℃后,薄膜的Raman谱图中由未退火时在1157,1346,1470,1555 cm^-1处的4个峰转变为只有D峰和G峰,说明晶界上的氢大量解吸附量减少,并且D峰和G峰的积分强度比I_D/I_G值变为最小,即sp²相团簇     

水浴法制备ZnO纳米棒及其场发射性能

用硝酸锌(Zn(NO3)2·6H2O)与六亚甲基四胺(C6H12N4)以等浓度配制成反应溶液,通过水浴法制备出了形貌可控的棒状ZnO纳米结构,讨论了不同反应浓度及衬底对ZnO表面形貌的影响.样品的XRD和扫描电子显微镜分析结果表明,所得产物均为六方纤锌矿结构,在有晶种层的衬底上制备出的ZnO纳米棒沿(001)方向并垂直于衬底表面生长.随着反应浓度的增加,ZnO纳米棒的直径增大,长径比减小.样品的场发射性能测试表明,反应溶液浓度为0.005 mol/L,以铜膜为晶种层的硅衬底上制备出的场发射阴极具有较好的场发射性能.     

两步化学沉积法制备ZnO薄膜及其场发射特性

在低温常压条件下,以ITO玻璃为衬底,采用电化学法与湿化学法结合的两步化学沉积法制备了团簇状ZnO薄膜。利用XRD,SEM分析了薄膜结构和表面形貌,并采用二极管结构在高真空条件下对薄膜进行了场发射性能测试。稳定发射后,开启电场为3.0 V/μm。当电场为5.8 V/μm时,电流密度为583.3 μA/cm²。研究表明:两步化学沉积法低温制备ZnO薄膜是可行的,且该薄膜具有良好的场发射性能。     

用热丝CVD技术制备场发射冷阴极金刚石薄膜

以甲烷和氢气的混合气体为原料,用热丝化学汽相淀积法,在(100)硅衬底上800℃温度时异质生长出适合场发射的金刚石薄膜.然后用扫描电子显微镜、X射线衍射仪、透射电子显微镜和喇曼光谱仪等对其进行了分析,结果表明,所制备的薄膜是多晶金刚石,而且在(111)晶相择优生长.在扫描电子显微镜下(111)晶粒的外形几乎都是四面体结构,具有很多尖端,可以加强一定电压下的电场,所以所制备的薄膜能够满足低压场发射的要求.     

氧离子注入纳米金刚石薄膜的微结构和电化学性能研究

在纳米金刚石薄膜中注入剂量为1012cm-2的氧离子,并进行700,800,900和1000?C的真空退火处理,系统研究薄膜的微结构和电化学性能结果表明,氧离子注入未退火(O120)和氧离子注入1000?C退火(O121000)电极的电势窗口分别为4.60 V和3.61 V,远大于其他电极的电势窗口,并且这两个样品的电极传质效率较高,说明氧离子注入和高温退火有利于提高电极的传质效率.红外光谱测试表明,样品O120和O121000的表面没有碳氢基团终止层,而其他样品均含有氢终止层,说明氧离子注入和高温退火破坏了薄膜表面含碳氢基团的氢终止层,提高了薄膜的电化学性能Raman光谱测试结果表明,金刚石含量较高、内应力较小和非晶石墨相无序化程度较大的样品具有较好的电化学性能;并且薄膜晶界处的非晶碳的团簇数量或者尺寸减小,样品的电化学性能提高.     

退火时间对硼掺杂纳米金刚石薄膜微结构和电化学性能的影响

采用高分辨透射电镜、紫外和可见光Raman光谱及循环伏安法研究了1000 ℃下退火不同时间的硼掺杂纳米金刚石薄膜的微结构和电化学性能. 结果表明,随退火时间的延长,薄膜中纳米金刚石晶粒尺寸逐渐减小.当退火时间为0.5 h时, 金刚石晶粒尺寸由未退火样品的约15 nm减小为约8 nm, 金刚石相含量增加;当退火时间为2.0 h时,金刚石晶粒减小为2—3 nm, 此时晶界增多,金刚石相含量减少;退火时间为2.5 h时纳米金刚石晶粒尺寸和金刚石相含量又略有上升.晶粒尺寸和金刚石相含量的变化表明薄膜在退火过程中发生了金刚石和非晶碳相的相互转变.可见光Raman光谱测试结果表明,不同退火时间下, G峰位置变化趋势与I_D/I_G值变化一致,说明薄膜内sp²碳团簇较大时, 非晶石墨相的有序化程度较高.退火0.5, 1.0, 1.5和2.0 h时, 电极表面进行准可逆电化学反应,而未退火和退火时间为2.5 h时电极表面进行不可逆电化学反应.退火有利于提高薄膜电极的传质效率, 退火0.5 h时薄膜电极的传质效率最高,催化氧化性能最好.较小的晶粒尺寸、 较高的金刚石相含量以及纳米金刚石晶粒的均匀分布有利于提高电极表面反应的可逆性和催化氧化性能.     

Fabrication of ZnO nanoparticles-embedded hydrogenated diamond-like carbon films by electrochemical deposition technique

ZnO nanoparticles-embedded hydrogenated diamond-like carbon (ZnO-DLC) films have been prepared by electrochemical deposition in ambient conditions. The morphology, composition, and microstructure of the films have been investigated. The results show that the resultant films are hydrogenated diamond-like carbon films embedded with ZnO nanoparticles in wurtzite structure, and the content and size of the ZnO nanoparticles increase with increasing deposition voltage, which are confirmed by X-ray photoelectron spectroscopy (XPS), Raman, and transmission electron microscope (TEM). Furthermore, a possible mechanism used to describe the growth process of ZnO-DLC films by electrochemical deposition is also discussed.     

Surface properties of diamond-like carbon films prepared by CVD and PVD methods

Diamond-like carbon (DLC) films have been deposited using three different techniques: (a) electron cyclotron resonance---plasma source ion implantation, (b) low-pressure dielectric barrier discharge, (c) filtered---pulsed cathodic arc discharge. The surface and mechanical properties of these films are compared using atomic force microscope-based tests. The experimental results show that hydrogenated DLC films are covered with soft surface layers enriched with hydrogen and sp$^{3}$ hybridized carbon while the soft surface layers of tetrahedral amorphous carbon (ta-C) films have graphite-like structure. The formation of soft surface layers can be associated with the surface diffusion and growth induced by the low-energy deposition process. For typical CVD methods, the atomic hydrogen in the plasmas can contribute to the formation of hydrogen and sp$^{3}$ hybridized carbon enriched surface layers. The high-energy ion implantation causes the rearrangement of atoms beneath the surface layer and leads to an increase in film density. The ta-C films can be deposited using the medium energy carbon ions in the highly-ionized plasma.     

Determination of the optical bandgap for diamond-like carbon films obtained by laser plasma deposition

We have obtained and analyzed the optical transmission spectra of diamond-like carbon films deposited on quartz substrates by pulsed laser deposition (λ = 1064 nm, τ = 20 nsec, q = 4.9·10⁸ W/cm²) under vacuum (p = 2.6·10⁻³ Pa). Based on the spectra obtained, we have estimated the size of the bandgap by the Tauc method, and also have studied the growth dynamics of the coatings formed. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 5, pp. 637–641, September–October, 2007.     

离子束辅助沉积对类金刚石膜结构影响的计算机模拟

采用分子动力学(MD)模拟研究了离子束辅助沉积(1BAD)生长类金刚石(DLC)膜的物理过程.分 别选C₂分子和Ar离子作为沉积源和辅助沉积粒子.改变Ar的入射能量和到达比(A r／C)，研 究了它对DLC膜结构的影响.重点讨论了Ar辅助沉积引起表面原子的瞬间活性变化对薄膜结构 产生的影响.分析表明，由于Ar离子的轰击引起的能量和动量的传递，大大地增强了C原子在 表面的反冲动能及迁移概率，增加了合成薄膜的SP³键含量.研究结果和实验 观察一致，并从合成机理上给出了一些定量解释. 关键词： 类金刚石膜 离子束辅助沉积 分子动力学模拟     

沉积温度对钛硅共掺杂类金刚石薄膜生长、结构和力学性能的影响

采用中频磁控溅射Ti80Si20复合靶在单晶硅表面制备了共掺杂的类金刚石薄膜.研究了沉积温度对薄膜生长速率、化学成分、结构、表面性质和力学性能的影响.结果表明:随沉积温度升高,薄膜生长速率降低,薄膜Ti和Si原子浓度增加,C原子浓度降低;在高温下沉积的薄膜具有低sp3C含量、低表面接触角、低内应力和高的硬度与弹性模量.基于亚表层注入生长模型分析了沉积温度对薄膜生长和键合结构的影响,从薄膜生长机制和微观结构解释了表面性质和力学性能的变化.     

Tribological properties of diamond-like carbon films deposited by pulsed laser arc deposition

A novel method, pulsed laser arc deposition combining the advantages of pulsed laser deposition and cathode vacuum arc techniques, was used to deposit the diamond-like carbon (DLC) nanofilms with different thicknesses. Spectroscopic ellipsometer, Auger electron spectroscopy, x-ray photoelectron spectroscopy, Raman spectroscopy, atomic force microscopy, scanning electron microscopy and multi-functional friction and wear tester were employed to investigate the physical and tribological properties of the deposited films. The results show that the deposited films are amorphous and the sp$^{2}$, sp$^{3}$ and C--O bonds at the top surface of the films are identified. The Raman peak intensity and surface roughness increase with increasing film thickness. Friction coefficients are about 0.1, 0.15, 0.18, when the film thicknesses are in the range of 17--21~nm, 30--57~nm, 67--123~nm, respectively. This is attributed to the united effects of substrate and surface roughness. The wear mechanism of DLC films is mainly abrasive wear when film thickness is in the range of 17--41~nm, while it transforms to abrasive and adhesive wear, when the film thickness lies between 72 and 123~nm.     

Effect of deposition voltage on the field emission properties of electrodeposited diamond-like carbon films

Diamond-like carbon (DLC) films were deposited on Al substrates by electrodeposition technique under various voltages. The surface morphology and compositions of synthesized films were characterized by scanning electron microscopy and Raman spectroscopy. With the increase of deposition voltage, the sp² phase concentration decreased and the surface morphology changed dramatically. The influence of deposition voltage on the field electron emission (FEE) properties of DLC films was not monotonic due to two adverse effects of deposition voltage on the surface morphology and compositions. The DLC film deposited under 1200 V exhibited optimum FEE property, including a lowest threshold field of 13 V/μm and a largest emission current density of 904.8 μA/cm² at 23.5 V/μm.     

脉冲激光沉积无氢钨掺杂类金刚石膜的摩擦与机械性能

采用脉冲激光沉积技术制备出无氢钨掺杂非晶态类金刚石膜.膜中的钨含量与靶材中的钨含量保持稳定的线性关系,显示了脉冲激光沉积在难熔金属掺杂技术方面的亮点.由于碳-钨结构的形成和表面粗糙度影响,膜层的干摩擦系数随着钨含量的增加显现出先减后增的趋势,钨含量为9.67 at.％时达到最低值0.091.钨含量的增大降低了类金刚石膜...     

横向电场下的类金刚石薄膜激光损伤

类金刚石（DLC）薄膜在红外区有很高的透过率,但激光损伤阈值低,严重限制了其应用领域。采用直接在DLC薄膜上沉积Ti电极,基于激光损伤阈值（LIDT）测试平台,用1-on-1零几率损伤法,研究了在不同偏置电场下DLC薄膜损伤阈值及损伤形貌的变化。发现电场强度从0增加到700 V/cm,损伤阈值明显增大;进一步增大偏置电场,损伤阈值相对不变。分析认为偏置电场改变了激光辐照DLC薄膜区域的光生载流子漂移速度,减小了DLC薄膜的局部热累积,减缓了薄膜的石墨化进程,提高了DLC薄膜的抗激光损伤阈值。