Mn4+掺杂对BiFeO3陶瓷微观结构和电学性能的影响研究

利用传统的固相反应法制备了BiFe_1-xMn_xO₃ (x= 0-0.20)陶瓷样品, 研究了不同Mn⁴⁺掺杂量对BiFeO₃陶瓷密度、物相结构、显微形貌、 介电性能和铁电性能的影响.实验结果表明:所制备的BiFe_1-xMn_xO₃ 陶瓷样品的钙钛矿主相均已形成,具有良好的晶体结构, 且在掺杂量x=0.05附近开始出现结构相变.随着Mn⁴⁺添加量的增加, 体系的相结构有从菱方钙钛矿向斜方转变的趋势,且样品电容率大幅度增大, 而介电损耗也略有增加;在测试频率为10⁴ Hz条件下, BiFe_0.85Mn_0.15O₃ (ε_r=1065)的 ε_r是纯BiFeO₃ (ε_r=50.6)的22倍; 掺杂后样品的铁电极化性能均有不同程度的提高,可能是由于Mn⁴⁺稳定性优于 Fe³⁺,高价位Mn⁴⁺进行B位替代改性BiFeO₃陶瓷, 能减少Bi³⁺挥发,抑制Fe³⁺价态波动,从而降低氧空位浓度,减小样品的电导和漏电流.     

Nd掺杂对Bi4Ti3O12铁电薄膜的微结构和铁电性能的影响

利用溶胶-凝胶法在Pt/Ti/SiO₂/Si(100)衬底上制备了Nd掺杂Bi₄Ti₃O₁₂(Bi_4-xNd_xTi₃O₁₂, x=0.00,0.30,0.45,0.75,0.85,1.00,1.50)铁电薄膜样品.研究了Nd掺杂对Bi₄Ti₃O₁₂薄膜的微结构和铁电性能的影响.研究结果表明:Nd掺杂未改变Bi₄Ti₃O₁₂薄膜的基本晶体结构.在掺杂量x<0.45时,Nd³⁺只取代类钙钛矿层中的A位Bi³⁺.当x=0.45时,样品剩余极化强度达最大值,在270kV·cm^-1的电场下为32.7μC·cm^-2.掺杂量进一步增加时,结构无序度开始明显增大,Nd³⁺开始进入(Bi₂O₂)²⁺层,削弱其绝缘层和空间电荷库的作用,导致材料剩余极化逐渐下降.当掺杂量x达到1.50时,掺杂离子最终破坏(Bi₂O₂)²⁺层的结构,材料发生铁电-顺电相变.     

掺入Ni2+和V3+对α-Al2O3晶体光谱精细结构、晶体局域结构和零场分裂参量的影响

应用晶体场理论和不可约张量算符方法构造了3d2/3d8态离子在C3v对称晶场中包含自旋-轨道相互作用、自旋-自旋相互作用、自旋-其它轨道相互作用和其它轨道-其它轨道相互作用四种微观磁效应的45阶可完全对角化的能量哈密顿矩阵.利用该矩阵,计算了V³⁺∶α-Al₂O₃和Ni²⁺∶α-Al₂O₃晶体的光谱精细结构、晶体局域结构和零场分裂参量,研究了掺入两种互补态离子Ni²⁺和V³⁺对同种晶体的光谱精细结构、晶体局域结构和零场分裂参量的影响,理论计算值和实验值相符.研究发现：掺杂没有改变晶体的光谱精细结构和能级分裂条数,但改变了能级间距|掺杂也没有改变晶体的对称性,但使晶体局域结构发生了一定程度的畸变| Ni²⁺∶α-Al₂O₃晶体局域结构的伸长畸变量大于V³⁺∶α-Al₂O₃晶体,键角的变化量小于V³⁺∶α-Al₂O₃晶体.     

Eu2+, Cr3+共掺杂的MAl12O19 (M=Ca, Sr, Ba) 的发光性质及能量传递

三基色荧光粉中, 红色荧光粉性能较差, 为获得性能优良的红色荧光粉, 本文采用高温固相法合成了Eu²⁺, Cr³⁺单掺杂及共掺杂的碱土金属多铝酸盐MAl₁₂O₁₉ (M =Ca, Sr, Ba) 发光体. 实验表明, 在以上三种基质中均存在Eu²⁺→Cr³⁺的能量传递, 利用能量传递可以有效将Eu²⁺的蓝光或绿光转换为红光. 三种碱土金属多铝酸盐基质的晶体结构相似,但Eu²⁺, Cr³⁺发光受晶体场影响,导致在不同的基质中Eu²⁺, Cr³⁺间能量传递效率不同.通过光谱分析及能量传递效率计算发现, 相同掺杂浓度下,CaAl₁₂O₁₉中Eu²⁺→Cr³⁺的能量传递效率最高,SrAl₁₂O₁₉次之, BaAl₁₂O₁₉最低.红光转换率在CaAl₁₂O₁₉中最高.     

节能灯用BaMgAl10O17:Eu2+,Mn2+荧光粉的劣化机理研究

对节能灯用BaMgAl₁₀O₁₇: Eu²⁺,Mn²⁺荧光粉的热劣化和紫外辐照劣化机理进行了对比研究. 发现热处理和紫外辐照处理均对BaMgAl₁₀O₁₇: Eu²⁺,Mn²⁺产生明显的发光劣化作用. 研究结果表明：热劣化主要涉及到Eu²⁺ 的氧化及其格位偏移, 而紫外辐照劣化与上述过程无关. 紫外辐照劣化主要源自高能紫外辐照使Eu²⁺ 处于更加不稳定的状态, 从而降低Eu²⁺ 的直接吸收和发射强度.     

Ca3Sc2Si3O12:Ce3+的第一性原理研究

对Ca₃Sc₂Si₃O₁₂:Ce³⁺共掺杂N^3-、Sc³⁺、Mn²⁺、Mg²⁺和Na⁺进行第一性原理计算,研究不同的电荷补偿对发光中心Ce³⁺的影响．首先利用密度泛函理论构建超晶胞模型对Ce³⁺周围的局部结构进行了优化,然后通过CASSCF/CASPT2 RASSI-SO计算得到Ce³⁺的4f→5d跃迁能量．计算数据与实验光谱相吻合．实验光谱中的一个未知峰值理论分析确认是Sc³⁺替代Si⁴⁺导致的．     

Al2O3:V3+晶体局域结构及其自旋哈密顿参量研究

提出了解释掺杂离子局域结构畸变的配体平面移动模型，建立了此模型下晶体微观结构与自旋哈密顿参量之间的定量关系.在考虑自旋与自旋、自旋与另一电子轨道和轨道与轨道作用等微小磁相互作用的基础上，采用全组态完全对角化方法，对Al₂O₃晶体中V³⁺的局域结构和自旋哈密顿参量进行了系统的研究.结果表明，V³⁺掺入Al₂O₃晶体后，上下配体氧平面间距离增大了0.0060 nm.从而成功地解释了Al₂O₃:V³⁺晶体的自旋哈密顿参量.在此基础上，研究了三角晶场下3d²离子自旋哈密顿参量的微观起源.研究发现，自旋三重态对自旋哈密顿参量的贡献是主要的，微小磁相互作用对自旋哈密顿参量的贡献只与自旋三重态有关.     

LiAl5O8高压相变研究

 运用金刚石压砧同步辐射X射线衍射,对尖晶石结构的LiAl₅O₈进行了高压原位研究。实验发现：在高压下,一组LiAl₅O₈的新相衍射峰出现,随着压力的增加,其新相衍射峰逐渐增强,当压力增加到45.0 GPa时,LiAl₅O₈的低压相衍射峰全部消失,而形成了一组高压新相衍射峰。采用指标化程序对衍射数据进行处理和分析,确定这一高压新相为正交晶系结构,其晶胞参数为a=0.995 9 nm,b=0.644 7 nm,c=0.333 4 nm ,空间群为Pmm2。     

具有介孔结构的MnSiO3@Fe3O4@C纳米粒子的制备以及作为pH响应的T1-T2*双模MRI造影剂的研究应用

本文通过一个简单的、温和的方案制备了平均尺寸为120 nm,介孔结构的纳米粒子MnSiO₃@Fe₃O₄@C. 粒子的细胞毒性微小,可以用作T₁-T₂^*双模MRI造影剂. 酸性条件下MnSiO₃@Fe₃O₄@C释放出大量的Mn²⁺缩短T₁弛豫时间,提高成像分辨率. 超顺磁性的Fe₃O₄可以增强T₂对比成像,检测病变组织. 类似于肿瘤微环境/细胞器的酸性PBS(pH=5.0)中Mn²⁺的释放率达到31.66%,约为中性条件(pH=7.4)下的7倍. 释放的Mn²⁺通过内吞作用被细胞摄取,经肾脏排出,细胞毒性实验表明,MnSiO₃@Fe₃O₄@C具有低的细胞毒性,即使高浓度的200 ppm MnSiO₃@Fe₃O₄@C对HeLa细胞的毒性也相对较小. 对荷瘤小鼠静脉注射定量MnSiO₃@Fe₃O₄@C后,可以观察到一个快速增强的对比成像,给药24 h后,T₁MRI信号显著增强,达到132%,而T₂信号则明显降低至53.8%,活体MR成像证明了MnSiO₃@Fe₃O₄@C可以同时作为阳性和阴性造影剂. 此外,得益于介孔MnSiO₃优秀的酸敏感性,MnSiO₃@Fe₃O₄@C可以作为一种潜在的药物载体,实现肿瘤的诊疗一体化.     

针状纳米MnxNi0.5-xZn0.5Fe2O4的共沉淀法制备及表征

通过在碱液中共沉淀Mn²⁺、Ni²⁺和Fe²⁺后制备了棒状的前躯体,前躯体于不同温度煅烧后制得了Mn_xNi_0:5-xZn_0:5Fe₂O₄棒状体. 利用X射线衍射仪和透射电镜对棒状体的物相、形貌及粒径进行了表征,并利用振动样品磁强计对磁性能进行研究. 结果表明长径比大于15的棒状,随着x值的增加,Mn_xNi_0:5-xZn_0:5Fe₂O₄样品的直径增加,长度下降,长径比变小,当x=0.5时其直径在50 nm左右而长径比减小到7～8. 随着x值的增加,样品的矫顽力先增加后减少,x值达到0.4时样品的矫顽力再次增加,当煅烧温度为600 oC,x=0.5时样品的矫顽力最大为134.3 Oe. 饱和磁化强度随着x值的增加先增加后减少,当煅烧温度为800 oC和x=0.2时达到最大为68.5 Oe.     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

Bond lengths in ‘CaMn3’ (Mn4)O12: A new Jahn-Teller distortion of Mn3+ octahedra

The crystal structure of [CaMn₃] (Mn₄)O₁₂ has been refined with the Rietveld method by using neutron powder diffraction data. This compound is trigonal with the perovskite-like [NaMn₃] (Mn₄)O₁₂ arrangement. The trigonality is due to the 1:3 order between Mn⁴⁺ and Mn³⁺ on the octahedral sites. [CaMn₃] (Mn₄)O₁₂ contains two different types of Mn³⁺ Jahn-Teller distorted polyhedra: the first, which is found in all the AC₃B₄O₁₂ compounds is a rhombic prism, while the second is an apically contracted octahedron, which represents a new type of Jahn-Teller distortion for Mn³⁺ cations in oxide compounds.     

A study of nano-sized surface coating on LiMn2O4 materials

The present study used the Pechini process with a heat treatment to synthesize LiMn₂O₄ powder (LMO). After surface coating, a nano-sized oxidative film of Li-Ni-Mn formed on the surface of the LMO-Ni powders. The concentration of Mn³⁺ for the LMO-Ni powder was lower and the average electrovalence of Mn exceeded the theoretical value, resulting in the initial capacity of the LMO-Ni powder being lower than the LMO powder. However, the LMO-Ni powder with the Li/Ni film not only restrained Mn ions from dissolving into the electrolyte, but also improved the charge-discharge cycling capacity.     

Physicochemical properties of LiAl x Mn2 − x O4 and LiAl0.05Mn1.95O4 − y F y cathode material by the citric acid-assisted sol–gel method

LiAl _x Mn_2 − x O₄ and LiAl_0.05Mn_1.95O_4 − y F _y spinel have been successfully synthesized by citric acid-assisted sol–gel method. The structure and physicochemical properties of this as-prepared powder were investigated by electronic conductivity test, powder X-ray diffraction (XRD), scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), and galvanostatic charge–discharge test in detail. The electronic conductivity decreases with increasing of the content of doped Al. XRD patterns show that the diffraction of LiAl_0.05Mn_1.95O_4 − y F _y samples is similar, with all the peaks indexable in the Fd3m space group, and a little impurity appears in the LiAl_0.05Mn_1.95O_3.8F_0.2 sample. SEM reveals that all LiAl_0.05Mn_1.95O_4 − y F _y powders have the uniform, nearly cubic structure morphology with narrow size distribution which is less than 500 nm. Galvanostatic charge–discharge test indicates that LiAl_0.05Mn_1.95O₄ has the highest discharge capacity and electrochemical performance among all LiAl _x Mn_2 − x O₄ samples after 50 cycles, and the initial discharge capacity of LiAl_0.05Mn_1.95O_4 − y F _y (y = 0, 0.02, 0.05, 0.1) is 123.9, 124.6, 124.9, and 125.0 mAh g⁻¹, respectively, and their capacity retention ratios are 94.2%, 94.9%, 91.7%, and 89.9% after 50 cycles, respectively. EIS indicates that LiAl_0.05Mn_1.95O_3.98F_0.02 have smaller charge transfer resistance than that of LiAl_0.05Mn_1.95O₄ corresponding to the extraction of Li⁺ ions.     

Suppression of Jahn-Teller distortion by chromium and magnesium doping in spinel LiMn2O4: A first-principles study using GGA and GGA+U

The effect of doping spinel LiMn₂O₄ with chromium and magnesium has been studied using the first-principles spin density functional theory (DFT) within generalized gradient approximation (GGA ) and GGA+U. We find that GGA and GGA+U give different ground states for pristine LiMn₂O₄ and same ground state for doped systems. For LiMn₂O₄, the body-centered tetragonal phase was found to be the ground-state structure using GGA and face-centered orthorhombic using GGA+U, while for LiM_0.5Mn_1.5O₄ (MCr or Mg) it was base-centered monoclinic and for LiMMnO₄ (MCr or Mg) it was body-centered orthorhombic in both GGA and GGA+U. We find that GGA predicts the pristine LiMn₂O₄ to be metallic while GGA+U predicts it to be insulating, which is in accordance with the experimental observations. For doped spinels, GGA predicts the ground state to be half metallic while GGA+U predicts it to be insulating or metallic depending on the doping concentration. GGA+U predicts insulator-metal-insulator transition as a function of doping in case of Cr and in case of Mg the ground state is found to go from insulating to a half metallic state as a function of doping. Analysis of the charge density and the density of states (DOS) suggest a charge transfer from the dopants to the neighboring oxygen atoms and manganese atoms. We have calculated the Jahn-Teller active mode displacement Q₃ for doped compounds using GGA and GGA+U. The bond lengths calculated from GGA+U are found to be in better agreement with experimental bond lengths. Based on the bond lengths of metal and oxygen, we have also estimated the average oxidation states of the dopants.     

Surface modification of LiMn2O4 thin films at elevated temperature

In order to improve the cycle stability of spinel LiMn₂O₄ electrode at elevated temperature, the LiCoO₂-coated and Co-doped LiMn₂O₄ film were prepared by an electrostatic spray deposition (ESD) technique. LiCoO₂-coated LiMn₂O₄ film shows excellent cycling stability at 55 °C compared to pristine and Co-doped LiMn₂O₄ films. The samples were studied by X-ray diffraction, scanning electron microscopy, Auger electron spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The excellent performance of LiCoO₂-coated LiMn₂O₄ film can be explained by suppression of Mn dissolution. On the other hand, the LiCoO₂-layer on the LiMn₂O₄ surface allows a homogenous Li⁺ insertion/extraction during electrochemical cycles and improves its structure stability.     

Luminescence of Mn ions in ordered and disordered LiAl5O8

The phosphorescence and excitation spectra of Mn ions in the ordered and disordered phases of LiAl₅O₈ have been measured. In both phases Mn²⁺ ions substitute for Al³⁺ ions in two different tetrahedral sites of the LiAl₅O₈ lattice. In both sites in the ordered phase, sharp zero-phonon transitions have been observed in the low temperature phosphorescence and excitation spectra - these transitions were considerably broadened in the disordered phase due to crystal field inhomogeneity in that phase. The deviation from neutrality caused by the Mn²⁺ ions in the ordered phase is largely compensated by Mn⁴⁺ ions occupying octahedral Al³⁺ sites. On disordering, a large proportion of Mn⁴⁺ is reduced to Mn²⁺, while the remainder takes up a site with a higher proportion of Li⁺ ions as next nearest neighbours. This leads to an increase in the ionicity of the Mn⁴⁺ site in the disordered phase and hence to a larger value of the Racah parameter B.     

Atomic force microscopy study of surface morphology change in spinel LiMn2O4: Possibility of direct observation of Jahn-Teller instability

Surface morphology in 3.5 × 3.5 μm² area of spinel LiMn₂O₄, which is a typical cathode material for Li ion secondary batteries, is studied using an atomic force microscopy (AFM) with a conductive probe. Negative bias voltage is applied to the probe to attract Li⁺ ions toward LiMn₂O₄ surface during the AFM observation. Before applying the voltage (0 V), the whole LiMn₂O₄ surface is covered with scale-shaped grains. Under the negative voltage of 5.5 V, electric current abruptly increases, indicating Li⁺ ionic conduction. Simultaneously, part of the scale-shaped grains expand and flatten. Jahn-Teller phase transition, which is induced by the repulsive interaction between the Mn-e_g and O-2p electrons in Li accumulated layer, is proposed as a possible origin of these results.     

Nd0.5Pb0.5-xSrx (Mn, Fe)O3的局域结构畸变和磁输运性质的研究

通过X光衍射，穆斯堡尔谱和输运性质的测量研究了掺杂Fe的Nd0.5Pb0.5-xSrxMnO3样品的结构和磁输运性质。x光衍射和穆斯堡尔谱都表明了样品随Sr的增多结构畸变减小。Sr的掺杂同时也降低了室温时的电阻率并使磁电阻增大。由于在样品中Mn3+ 与 Mn4+的比率是一样的，也就意味着具有相同的双交换作用。所以Sr对样品性质的改变可以认为是由于晶格畸变所产生的。由于Jahn-Teller 效应而产生的Mn(Fe)O6八面体的局域结构畸变可以局域电子。由我们的实验可以看到在居里温度Tc以上，除了双交换作用之外，Jahn-Teller 效应对于输运性质也起了重要作用。     

Electrochemical behaviour of nano-sized spinel LiMn2O4 and LiAlxMn2−xO4 (x=Al: 0.00-0.40) synthesized via fumaric acid-assisted sol-gel synthesis for use in lithium rechargeable batteries

Pristine spinel LiMn₂O₄ and LiAl_xMn_2−xO₄ (x=Al: 0.00-0.40) with sub-micron sized particles have been synthesized using fumaric acid as chelating agent by sol-gel method. The synthesized samples were subjected to thermogravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and cyclic voltammetry (CV) and galvanostatic cycling studies. The TGA curve of the gel shows several weight-loss regions stepwise amounting to 55% till 800 °C attributed to the decomposition of the precursors. Calcination to higher temperatures (800 °C) yields pure-phase spinel (LiAl_xMn_2−xO₄), as it is evident from the high-intensity XRD reflections matching to the standard pattern. SEM and TEM studies confirm that the synthesized grains are of uniform regular surface morphology. FT-IR studies show stretching and bending vibration bands of Li-O, Li-Al-Mn-O. LiAl_0.1Mn_1.90O₄ spinel was found to deliver discharge capacity of 139 mA h/g during the first cycle with columbic efficiency of 97%. LiAl_0.1Mn_1.90O₄ spinel exhibits the high cathodic peak current indicating better electrochemical performance. Low doping (x=0.1) of Al is found to be beneficial in stabilizing the spinel structure.