在溴代十六烷基吡啶存在下5-Br-PADAP分光光度法测定水中微量铁的研究

研究了显色剂2-(5-溴-2-吡啶偶氮)-5-二乙氨基酚(简称为5-Br-PADAP)与铁(Ⅱ)显色反应条件,在pH=6.0的醋酸-醋酸钠缓冲体系中,采用阳离子表面活性剂溴代十六烷基吡啶增溶增敏。铁(Ⅱ)与显色剂形成的配合物组成为Fe(Ⅱ)∶R=1∶2,络合物具有两个吸收峰,分别位于λ1=556nm与λ2=748nm。选择748nm进行测定,其摩尔吸光系数为ε748=3.3×104L·mol-1·cm-1。铁含量在0—30μg/25mL范围内服从比耳定律。此法用于水样中微量铁的测定,结果准确可靠。     

小波变换-偏最小二乘法用于Co,Ni,Zn的分光光度法同时测定

建立了以 2 (5 溴吡啶偶氮 ) 5 二乙氨基苯酚 (5 Br PADAP)作显色剂 ,溴代十六烷基吡啶 (CPB)为增溶增敏剂 ,用小波变换—偏最小二乘分光光度法同时测定钴 ,镍 ,锌的方法。在波长 5 30～ 5 90nm范围内每隔 2nm测定其吸光值 ,将测定结果分别用偏最小二乘法处理和经小波变换后用偏最小二乘法处理。结果表明 ,经小波变换后处理结果回收率明显提高。     

Triton X-100增敏催化动力学光度法测定痕量亚硝酸根

基于稀硫酸介质中,Triton X-100对亚硝酸根催化氯酸钾氧化甲基紫褪色反应的增敏作用,建立了测定痕量亚硝酸根的Triton X-100增敏催化动力学光度法.方法的线性范围为0.004-0.26μg·mL-1,检出限为9.24×10-10g·mL-1.测得反应表观活化能为75.33kJ·mol-1.方法简便、快速,选择性好.用于水样及蔬菜祥品中痕量亚硝酸根的测定,结果满意.     

钛—邻苯二酚紫—EDTA—溴化十六烷基哟眵元配合物显色反应的研究

在 p H6 .2的 HAc- Na Ac缓冲液中 ,钛与邻苯二酚紫、EDTA、溴化十六烷基吡啶形成 1∶ 3∶ 2∶ 2的多元配合物 ,在 5 6 9.3nm处有最大吸收 ,摩尔吸光系数ε=5 .5× 1 0 4 L· mol- 1 · cm- 1 。钛量在 2—1 5 μg/ 2 5 m L范围内符合比耳定律。方法可用于工业硅中微量钛的测定。     

抑制CTMAB催化结晶紫褪色光度法测定痕量铝(Ⅲ)

基于碱性介质中 ,铝 (Ⅲ )对溴化十六烷基三甲铵 (CTMAB)催化结晶紫的褪色反应有明显的抑制作用 ,建立了一种抑制 -催化褪色光度法测定痕量铝 (Ⅲ )的新方法。此法在 0 .0 2— 1.8μg/L的范围内 CAl(Ⅲ )与 ΔA值呈线性关系 ,线性回归方程为 :ΔA=0 .0 0 2 93+ 0 .2 179CAl( Ⅲ ) (μg/L) ,r=0 .9990 ,检出限为 1.4×10 -9g/m L。该法用于水样中 Al(Ⅲ )的测定 ,结果令人满意。     

阳离子表面活性剂与溴酚红的显色反应及其分析应用

研究了阳离子表面活性剂 (CSAA)溴化十六烷基三甲铵 (CTAB)、溴化十六烷基吡啶 (CPB)在水溶液中与溴酚红 (BPR)的显色反应。发现在pH 5 0～ 6 0范围内 ,CSAA单体与BPR形成离子缔合物(缔合比为 3∶2 ) ,可用于微量CSAA及CSAA的临界胶束浓度 (CMC)的测定。本文还研究了显色反应的适宜条件、分析特征 ,并讨论了反应机理     

表面活性剂对空气-乙炔火焰原子吸收法测定铝的增感效应研究

研究了溴化十六烷基三甲基胺、氯化十六烷基吡啶等10种表面活性剂对测定铝时的增感效应。结果表明,在实验所选择的表面活性剂中,阳离子表面活性剂对铝有明显增感作用,阴离子表面活性剂对铝有抑制作用,而特殊表面活性剂对铝没有作用。以溴化十六烷基三甲基胺(CTMAB)为增感剂,研究了空气-乙炔火焰原子吸收法测定铝镍合金样品中铝的工作条件、CTMAB用量、溶液介质和浓度及共存离子干扰的影响。测定铝的线性范围为0.10～2.0g·L-1,方法的相对标准偏差为2.6%,标准加入回收率在97%～103%之间。     

水溶性苯胺蓝分光光度法测定微量亚硝酸根

在 0 .0 0 5 mol/L的盐酸介质下 ,水溶性苯胺蓝体系在 6 0 3nm处的吸光度随亚硝酸根含量的增加而减小 ,表观摩尔吸光系数为 1.5 7× 10 4L· mol-1· cm-1。亚硝酸根浓度在 0 .0 4— 4 .4 2μg/m L范围内符合比耳定律 ,据此建立了一种测定痕量亚硝酸根的新分光光度法 ,用于合成样品中亚硝酸根含量的测定 ,结果令人满意。     

钛-邻苯二酚紫-EDTA-溴化十六烷基吡啶多元配合物显色反应的研究

在pH6.2的HAc-NaAc缓冲液中,钛与邻苯二酚紫、EDTA、溴化十六烷基吡啶形成1∶3∶2∶2的多元配合物,在569.3nm处有最大吸收,摩尔吸光系数ε=5.5×104L.mol-1.cm-1.钛量在2-15μg/25mL范围内符合比耳定律.方法可用于工业硅中微量钛的测定.     

微乳液增敏光度法测定大米中的痕量铜

研究了溴化十六烷基三甲基铵(CTMAB)和正丁醇、正庚烷、水4组分构成的微乳液对铬天青S与铜(Ⅱ)显色反应的增敏作用,建立了测定大米中痕量铜(Ⅱ)的分光光度新方法.结果表明,在pH=6.00的NaH2PO4-NaAc缓冲溶液介质中,铜(Ⅱ)与铬天青S形成蓝绿色配合物,λmax=604 nm,表观摩尔吸光系数为6.608×104 L·mol-1·cm-1,在0-1.2 mg/L范围内吸光度与Cu2 浓度呈良好的线形关系,线性回归方程为:A=-0.01475 0.39036V,相关系数为r=0.9996.应用该方法对大米中的铜进行测定,相对标准偏差RSD=2.8%,加标回收率为97%-104%.结果表明,该方法具有较高的灵敏度、准确度与精密度,适合大米中痕量铜的测定.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.