Barium molybdate and barium tungstate nanocrystals synthesized by a cyclic microwave irradiation

BaMoO₄ and BaWO₄ nanocrystals were synthesized from Ba(NO₃)₂ and Na₂MeO₄ (Me=Mo and W) solutions using 50% of 600 W microwave irradiation for 20 min. The products were characterized using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), selected area electron diffraction (SAED) and photoluminescence (PL) spectrophotometry. They show that the products are good dispersed nanocrystals (poly-nanocrystals) of single-phase scheelite tetragonal structure with the vibration modes corresponding to the molybdate and tungstate compounds. Their photoluminescence was detected at 415 and 392 nm for BaMoO₄ and BaWO₄, respectively.     

Electrospun nanofibers of poly(ethylene oxide)/teraamino-phthalocyanine copper(II) hybrids and its photoluminescence properties

Poly(ethylene oxide)/teraamino-phthalocyanine copper (II) (PEO/(NH₂)₄PcCu) hybrid nanofibers with a diameter of 200-300 nm were prepared by electrospinning technique. The hybrid nanofibers membrane was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), ultraviolet-visible (UV-vis), and photoluminescence (PL), respectively. The results indicated that (NH₂)₄PcCu molecule was successfully embedded in the one-dimensional hybrid nanofibers via chemical interaction between PEO and (NH₂)₄PcCu. The PL results showed that the PEO/(NH₂)₄PcCu hybrid nanofibers had an intense emission at about 450 nm. A possible PL mechanism was proposed accordingly.     

Disorder-dependent photoluminescence in Ba0.8Ca0.2TiO3 at room temperature

The photoluminescence (PL) emission in structurally disordered Ba_0.8Ca_0.2TiO₃ (BCT20) powders was observed at room temperature with laser excitation at lines 355 and 460 nm. The structural evolution perovskite-like titanate BCT20 powders prepared by a soft chemical processing at different annealing temperatures were accompanied by X-ray diffraction (XRD) and X-ray absorption near-edge structure (XANES). Intermediate oxycarbonate phase was identified and your influence with PL emission was discarding. BCT20 annealed at 500 °C displays intense PL emission. The results indicate relationship between broad PL band and order-disorder degree.     

Intense and broad photoluminescence at room temperature in structurally disordered Ba[Zr0.25Ti0.75]O3 powders: An experimental/theoretical correlation

Intense and broad photoluminescence (PL) emission at room temperature was observed on structurally disordered Ba[Zr_0.25Ti_0.75]O₃ (BZT) powders synthesized by the polymeric precursor method. BZT powders were annealed at 573 K for different times and at 973 K for 2 h in oxygen atmosphere. The single-phase cubic perovskite structure of the powder annealed at 973 K for 2 h was identified by X-ray diffraction and Fourier transform Raman techniques. PL emission increased with the increase of annealing time, which reached its maximum value in the powder annealed at 573 K for 192 h. First principles quantum mechanical calculations based on density functional theory (B3LYP level) were employed to study the electronic structure of ordered and disordered models. The theoretical calculations and experimental measurements of Ultraviolet-visible absorption spectroscopy indicate that the presence of intermediary energy levels in the band gap is favorable for the intense and broad PL emission at room temperature in disordered BZT powders. The PL behavior is probably due the existence of a charge gradient on the disordered structure, denoted by means of a charge transfer process from [TiO₅]-[ZrO₆] or [TiO₆]-[ZrO₅] clusters to [TiO₆]-[ZrO₆] clusters.     

Synthesis of nanocrystalline and mesoporous zinc sulphide from a single precursor Zn(SOCCH3)2Lut2 complex

We report the formation of mesoporous zinc sulphide, composed by the fine network of nanoparticles, which was formed via a single precursor Zn(SOCCH₃)₂Lut₂ complex. The complex was chemically synthesized using zinc carbonate basic, 3,5-lutidine and thioacetic acid, in air. The metal precursor complex was characterized using different conventional techniques. Thermogravimetric analysis (TGA) result indicates that the decomposition of the complex starts at 100 °C and continues up to 450 °C, finally yielding ZnS. ZnS nanocrystals were characterized by powder X-ray diffraction (XRD) technique, field emission scanning electron microscopy (FESEM), N₂-sorption isotherm, UV-vis spectroscopy and photoluminescence (PL) spectroscopy. The grain diameter of nanocrystals was found to be 4-5 nm. The material followed Type-IV N₂-sorption isotherm, which is the characteristic of mesoporous materials. The band gap energy, as obtained from optical measurements was around 3.8 eV.     

Precipitate synthesis of BaMoO4 and BaWO4 nanoparticles at room temperature and their photoluminescence properties

The uniform BaMoO₄ and BaWO₄ nanoparticles (NPs) have been successfully synthesized by solution route – the direct precipitation of Ba(NO₃)₂ and Na₂MO₄ (M = Mo and W) in ethylene glycol under 24 h stirring. The XRD patterns and SEM images proved that the products were tetragonal structured BaMoO₄ and BaWO₄ with uniform round nanoparticles. Shape, average particle size and particle-size distribution of products were analyzed by TEM – showing the round nanoparticles with the average size of 31.52 ± 4.65 nm for BaMoO₄, and 59.77 ± 9.61 nm for BaWO₄. The room temperature photoluminescence (PL) indicated that the products have strong blue emission centered at 441 nm – excited with 280 nm wavelength for BaMoO₄ NPs, and strong violet emission centered 378 nm – excited with 344 nm wavelength for BaWO₄ NPs. These PL behaviors attributed the existence of intrinsic transitions in the [MO₄]^2-$[{\text{MO}}_4{]}^{2-}$ (M = Mo and W) tetrahedrons of their crystal lattices.     

Synthesis of In-doped Ga2O3 zigzag-shaped nanowires and optical properties

In-doped Ga₂O₃ zigzag-shaped nanowires and undoped Ga₂O₃ nanowires have been synthesized on Si substrate by thermal evaporation of mixed powders of Ga, In₂O₃ and graphite at 1000 °C without using any catalyst via a vapor-solid growth mechanism. The morphologies and microstructures of the products were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and photoluminescence spectroscopy (PL). The nanowires range from 100 nm to several hundreds of nanometers in diameter and several tens of micrometers in length. A broad emission band from 400 to 700 nm is obtained in the PL spectrum of these nanowires at room temperature. There are two blue-emission peaks centering at 450 and 500 nm, which originate from the oxygen vacancies, gallium vacancies and gallium-oxygen vacancy pairs.     

Structural, optical and electrical properties of ZnO/Zn2GeO4 porous-like thin film and wires

Zinc oxide/zinc germanium oxide (ZnO/Zn₂GeO₄) porous-like thin film and wires has been fabricated by simple thermal evaporation method at temperature about 1120 °C for 2.5 h. The structural and optical properties of the porous-like-thin film and wires have been investigated by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. Metal semiconductor metal (MSM) photodetector structure was used to evaluate the electrical characteristics by using current-voltage (I-V) measurements. Room temperature photoluminescence spectrum of the sample shows one prominent ultraviolet peak at 378 nm and a shoulder at 370 nm. In addition, broad visible blue emission peak at wavelength 480 nm and green emission peak at 500 nm are also observed. Strong photoelectric properties of the MSM in the UV demonstrated that the porous-like-thin film and wires contribute to its photosensitivity and therefore making ZnO/Zn₂GeO₄ wires potential photodetector in the shorter wavelength applications.     

Synthesis and fluorescence properties of pure and metal-doped spherical ZnS particles from EDTA-metal complexes

Monodispersed spherical ZnS particles as well as doped with Cu, Mn ions were synthesized from metal-chelate solutions of ethylenediamine tetraacetate (EDTA) and thioacetamide (TAA). The characterizations of the ZnS-based particles were investigated via TEM, SEM, XRD, TG/DTA and PL measurements. The sphere size was controlled from 50 nm to 1 μm by adjusting the nucleation temperatures and molar ratio of Zn-EDTA to TAA. The emission intensity continuously increased with the increase of the particle size. When the ZnS microspheres were annealed at 550-800 °C, there were two specific emission bands with the centers at 454 nm and 510 nm, which were associated with the trapped luminescence arising from the surface states and the stoichiometric vacancies, respectively. When Cu²⁺ was introduced into ZnS microspheres, the dominant emission was red-shifted from 454 to 508 nm, fluorescence intensity also sharply increased. However, for the Mn²⁺-doped ZnS, the emission intensity was significantly enhanced without the shift of emission site.     

Effect of the Order and Disorder of BaMoO4 Powders in Photoluminescent Properties

The study of the photoluminescent properties affected by order and disorder of the BaMoO₄ powders is the principal objective in this work. BaMoO₄ compounds were prepared using soft chemical process called Complex Polymerization Method. In this work, different deagglomeration types and different heating rates were used to promote different disorder degrees. Scheelite type phase (BaMoO₄) was determined by X-ray Diffraction (XRD), Fourier Transformed Infra-Red (FTIR) and Raman spectroscopy after heat treating the sample at 400°C. The room temperature luminescence spectra revealed an intense single-emission band in the visible region. Based on XRD and Raman data it was observed that the transition between the completely disordered structure to completely ordered structure is a good condition for photoluminescence (PL) emission. The best PL emission is obtained when the material possesses short range disorder, i.e., is periodically ordered (XRD), but some disorder as measured by Raman spectroscopy. The excellent optical properties observed for disordered BaMoO₄ suggested that this material is a highly promising candidate for optical applications.     

Electronic structure and optical properties of BaMoO4 powders

Barium molybdate (BaMoO₄) powders were synthesized by the co-precipitation method and processed in microwave-hydrothermal at 140 °C for different times. These powders were characterized by X-ray diffraction (XRD), Fourier transform Raman (FT-Raman), Fourier transform infrared (FT-IR), ultraviolet–visible (UV–vis) absorption spectroscopies and photoluminescence (PL) measurements. XRD patterns and FT-Raman spectra showed that these powders present a scheelite-type tetragonal structure without the presence of deleterious phases. FT-IR spectra exhibited a large absorption band situated at around 850.4 cm⁻¹, which is associated to the Mo–O antisymmetric stretching vibrations into the [MoO₄] clusters. UV–vis absorption spectra indicated a reduction in the intermediary energy levels within band gap with the processing time evolution. First-principles quantum mechanical calculations based on the density functional theory were employed in order to understand the electronic structure (band structure and density of states) of this material. The powders when excited with different wavelengths (350 nm and 488 nm) presented variations. This phenomenon was explained through a model based in the presence of intermediary energy levels (deep and shallow holes) within the band gap.     

Luminescence properties of hierarchical CaMoO4 microspheres derived by ionic liquid-assisted process

Hierarchical calcium molybdate (CaMoO₄) nanostructured microspheres were synthesized via a facile room-temperature route assisted by an ionic liquid, 1-n-butyl-3-methylimidazolium chloride. The product was characterized by means of X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that micro-scaled CaMoO₄ powders were assembled by nanoparticles with diameters ranging from 10 to 20 nm. The optical absorbance, photoluminescence emission (PL), and luminescence excitation (PLE) were investigated. The PL spectra excited at 273 nm have a strong green emission band maximum at 511 nm, which is attributed to the charge-transfer transitions within the MoO₄²⁻ complex, and the luminescence intensity indicated a good luminescence quality of the CaMoO₄ materials. By varying the amount of this assisted agent, we found that the ionic liquid played a crucial role as a surfactant in the formation of CaMoO₄ materials with uniform hierarchical structure, which may be beneficial to the luminescence performance. This study presented a promising preparation strategy towards other luminescent materials.     

Comparison of different NaGdF4:Eu synthesis routes and their influence on its structural and luminescent properties

Eu³⁺:NaGdF₄ samples were obtained via co-precipitation in aqueous solution (CP), reversed micelle (RM) method, reaction between solid GdF₃ and NaF solution (SR) as well as a solid-state reaction at high temperatures (SS). The synthesised materials were characterised using X-ray powder diffractometry, TEM microscopy, infrared spectroscopy and TGA analysis. For discussion of optical properties excitation and emission spectra were recorded and emission decay times were measured. The CP and RM methods allow to obtain powders with crystallite size of ∼10 nm, which may be smoothly increased to about 1 μm during post-fabrication heat treatment. Differences in structural and especially in optical properties of phosphors prepared by different techniques are emphasised and applicability of wet-chemistry routes for synthesis of fluoride powders is argued.     

Characterization and luminescent properties of SiO2:ZnS:Mn and ZnS:Mn nanophosphors synthesized by a sol-gel method

ZnS and SiO₂-ZnS nanophosphors, with or without different concentration of Mn²⁺ activator ions, were synthesized by using a sol-gel method. Dried gels were annealed at 600 °C for 2 h. Structure, morphology and particle sizes of the samples were determined by using X-ray diffraction (XRD), highresolution transmission electron microscopy (HRTEM) and field emission scanning electron microscopy (FESEM). The diffraction peaks associated with the zincblende and the wurtzite structures of ZnS were detected from as prepared ZnS powders and additional diffraction peaks associated with ZnO were detected from the annealed powders. The particle sizes of the ZnS powders were shown to increase from 3 to 50 nm when the powders were annealed at 600 °C. An UV-Vis spectrophotometer and a 325 nm He-Cd laser were used to investigate luminescent properties of the samples in air at room temperature. The bandgap of ZnS nanoparticles estimated from the UV-Vis data was 4.1 eV. Enhanced orange photoluminescence (PL) associated with ⁴T₁→⁶A₁ transitions of Mn²⁺ was observed from as prepared ZnS:Mn²⁺and SiO₂-ZnS:Mn²⁺ powders at 600 nm when the concentration of Mn²⁺ was varied from 2-20 mol%. This emission was suppressed when the powders were annealed at 600 °C resulting in two emission peaks at 450 and 560 nm, which can be ascribed to defects emission in SiO₂ and ZnO respectively. The mechanism of light emission from Mn²⁺, the effect of varying the concentration on the PL intensity, and the effect of annealing are discussed.     

Synthesis and photoluminescence of water-soluble Mn-doped ZnS quantum dots

The water-soluble Mn²⁺-doped ZnS quantum dots (Mn:ZnS d-dots) were synthesized by using thioglycolic acid (TGA) as stabilizer in aqueous solutions in air, and characterized by X-ray powder diffraction (XRD), UV-vis absorption spectra and photoluminescence (PL) emission spectroscopy. The sizes of Mn:ZnS d-dots were determined to be about 2 nm using XRD measurements and the UV-vis absorption spectra. It was found that the Mn²⁺⁴T₁ → ⁶A₁ emission intensity of Mn:ZnS d-dots significantly increased with the increase of Mn²⁺ concentration, and showed a maximum when Mn²⁺ doping content was 1.5%. If Mn²⁺ concentration continued to increase, namely more than 1.5%, the Mn²⁺⁴T₁ → ⁶A₁ emission intensity would decrease. In addition, the effects of TGA/(Zn + Mn) molar ratio on PL were investigated. It was found that the peak intensity ratio of Mn²⁺⁴T₁ → ⁶A₁ emission to defect-states emission showed a maximum when the TGA/(Zn + Mn) molar ratio was equal to 1.8.     

Synthesis and VUV spectral properties of nanoscaled Zn2SiO4:Mn green phosphor

Nanoscaled Zn₂SiO₄:Mn²⁺ green phosphor with regular and uniform morphology was synthesized by hydrothermal method at a low temperature of 140 °C. The structure and morphology of the phosphor was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of the hydrothermal temperature and the time on the crystallite structure and the vacuum ultraviolet (VUV) photoluminescence (PL) properties were evaluated. The as-synthesized nanoscaled Zn₂SiO₄:Mn²⁺ phosphor exhibited intensive broad emission around 523 nm, which was attributed to the ⁴T₁→⁶A₁ transition of Mn²⁺. The PL intensity increased along with the increasing hydrothermal temperature and time. The heat-treated phosphors exhibited higher PL intensity than the corresponding samples prepared using the conventional solid-state reaction.     

Photoluminescence of Y2O3:Eu thin film phosphors by sol-gel deposition and rapid thermal annealing

Y₂O₃:Eu³⁺ phosphor films have been developed by using the sol-gel process. Comprehensive characterization methods such as Photoluminescent (PL) spectroscopy, X-ray diffraction (XRD) and Fourier Transform Infrared (FTIR) spectroscopy were used to characterize the Y₂O₃:Eu³⁺ phosphor films. In this experiment, the XRD profiles show that the Y₂O₃:Eu³⁺ phosphor films crystallization temperature and optimum annealing temperature occur at about 650 and 750 °C, respectively. The optimum dopant concentration is 12 mol% Eu³⁺ and the critical transfer distance (R_c) among Eu³⁺ ions is calculated to be about 0.84 nm. Vacuum environment is more efficient than oxygen and nitrogen to eliminate the OH content and hence yields higher luminescent phosphor films. The PL emission intensity of Y₂O₃:Eu³⁺ phosphor films is also dependent on the annealing time. It was found that the H₂O impurities were effectively eliminated after annealing time of 25 s at 750 °C in vacuum environment. From the experiment results, the schematic energy band diagram of Y₂O₃:Eu³⁺ phosphor films is constructed.     

Size-dependent photoluminescent properties of uncapped CdS particles prepared by acoustic wave and microwave method

CdS particles with crystallite size of 5-12 nm have been prepared via acoustic wave stimulated (sonochemical) route and microwave initiated combustion method. X-ray line broadening and transmission electron microscopy (TEM) suggest that sonochemical powders are more amorphous (5-10 nm) compared to microwave-synthesized sulphides (10-15 nm). The photoluminescent (PL) properties of powders with size <10 nm show a clearly blue shifted, resolved emission with full-width at half-maxima (FWHM) ∼100 nm, while powders with size >15 nm show dominant blue to green narrow emission with FWHM ∼60 nm. The mechanistic details of the synthetic route appear to affect the morphology and consequently the PL properties to a significant extent.     

Microwave-assisted synthesis and optical property of CdMoO4 nanoparticles

Microwave-assisted synthesis is a novel method used to synthesize CdMoO₄ nanoparticles in propylene glycol. The effects of reaction time and microwave power on phase, morphologies, and optical properties of CdMoO₄ nanoparticles were studied, using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and UV-visible spectroscopy. The present analyses proved that these crystalline powders were scheelite-type tetragonal structured CdMoO₄, with the crystallite size of 14-20 nm, and 4.51-4.73 eV band gaps, controlled by the synthetic conditions.     

Optical properties of cadmium sulfide nanocrystal film prepared by electrochemical synthesis at liquid-liquid interface

Dendritic nanocrystalline CdS film was deposited at liquid-liquid interface of surfactants and an electrolyte containing 4 mmol L⁻¹ cadmium chloride (CdCl₂) and 16 mmol L⁻¹ thioacetamide (CH₃CSNH₂) with an initial pH value of 5 at 15 °C by electrochemical synthesis. The nanofilm was characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), ultraviolet visible (UV-vis) absorption spectroscopy and fluorescence spectroscopy. The surface morphology and particle size of the nanofilm were investigated by AFM, SEM and TEM, and the crystalline size was 30-50 nm. The thickness of the nanofilm calculated by optical absorption spectrum was 80 nm. The microstructure and composition of the nanofilm was investigated by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), showing its polycrystalline structure consisting of CdS and Cd. Optical properties of the nanofilm were investigated systematically by UV-vis absorption and fluorescence spectroscopy. A λ_onset blue shift compared with bulk CdS was observed in the absorption spectra. Fluorescence spectra of the nanofilm indicated that the CdS nanofilm emitted blue and green light. The nanocomposites film electrode will bring about anodic photocurrent during illumination, showing that the transfer of cavities produces photocurrent.