MgB2 fabrication by diffusion-controlled three layered (B-Mg-B) technique

MgB₂ was successfully fabricated through diffusion-controlled three-layered (B-Mg-B) technique under high pressure. Due to melting temperature of Mg, the material was pre-heat treated at 600 °C between 1 and 48 h. Optimum pre-heat treatment condition was found to be 600 °C for 48 h. Then, the compacted material was grinded and pelletized under pressure of 2 ton. The pellets were heat treated at 600-900 °C for 1-48 h. Optimum heat treatment condition was determined to be 800 °C for 1 h for formation of almost pure MgB₂. Diffusion coefficient was determined with Fick's law and EDX data. Diffusion coefficient value for B in Mg matrix and Mg in B matrix was determined to be 1.66×10⁻⁷ and 3.14×10⁻⁸ cm²/sn, respectively. Best T_c value (39.4 K) was obtained for material heat treated at 800 °C for 1 h. A symmetric hysteresis was obtained for the best MgB₂ material and magnetization decreased with increase in the temperature and the applied magnetic field.     

On the power-law behavior of the AC conductivity of the mixed crystal (NH4)3H(SO4)1.42(SeO4)0.58

A power law used to describe the AC conductivity from 299 to 393 K of the mixed crystal (NH₄)₃H(SO₄)_1.42(SeO₄)_0.58 led to fractional exponent values ranging from 1.08 to 0.91, depending on structural changes induced on temperature variation [B. Louati, M. Gargouri, K. Guidara and T. Mhiri, J. Phys. Chem. Solids 66 (2005) 762]. In the present note, we suggest that the fractional law exhibits features of lattice relaxation. Despite the structural changes, the parameters of the power law are mutually interconnected to yield a temperature independent phenomenon. Such behavior is probably of general validity and characterizes the universal fractional dispersion of the AC conductivity, as it was also observed in glasses of different composition.     

Study of the structural, dielectric and magnetic properties of Bi2O3 and PbO addition on BiFeO3 ceramic matrix

In this paper we studied the effects of Bi₂O₃ and PbO addition on BiFeO₃ (BFO) ceramic matrix. The structural, dielectric and magnetic properties of fifteen BFO samples were discussed in view of possible applications in RF and microwave devices. The present work also reports the preparation of the samples. Polyvinyl alcohol (PVA) and tetraethyl orthosilicate (TEOS) were also added as a binder in the fabrication procedure. The samples have been studied by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and magnetic hysteresis measurements. Further, a study based on impedance spectroscopy also has been done. Dielectric permittivity (ε′) and dielectric loss (tan δ) were measured at room temperature in the frequency range 100 Hz-10 MHz, as well as a.c. conductivity. The -Im[Z(f)] versus Re[Z(f)] plot has been obtained. The samples were investigated in view of possible applications like miniaturized filters, diplexers and dielectric resonator antennas (DRA). In the RF and MW frequency region, the application of magneto-dielectric and multiferroic perovskite composite materials is desirable for the miniaturization of components.     

The unusual magnetic and electronic properties of Gd0.5Ba0.5CoO2.9

Magnetic and electrical properties of well-characterized Gd_0.5Ba_0.5CoO_2.9 have been studied carefully in order to compare them with those of other analogous cobaltates of the type Ln_0.5A_0.5CoO₃ (Ln=La, Nd and A=Sr, Ba) which are ferromagnetic. The results show that Gd_0.5Ba_0.5CoO_2.9, which has A-site cation ordering at room temperature, does not become a genuine ferromagnet at low temperatures, but the ferromagnetic interactions observed at 280 K give over to an antiferromagnetic (AFM) state on cooling to 230 K. The AFM state is rendered ferromagnetic on the application of high magnetic fields. The properties can be understood on the basis of phase separation induced by the large A-site cation-disorder, arising from the size mismatch.     

Synthesis and magnetic properties of three-dimensional metal (II) organophosphates

A new series of metal (II) organophosphates with the formula M(II) 2(H₂O)₂[O₃PCH₂(C₆H₄)CH₂PO₃] (M=Mn, Fe and Ni) have been prepared by hydrothermal synthesis. The structure consisted of two-dimensional metal–oxygen inorganic layers is pillared by p-xylylenediphosphonate to form a three dimensional framework. The layers are constructed by corner-sharing metal oxygen polyhedron. A study on the magnetism of the materials indicates the presence of spin canted antiferromagnetc interactions. The manganese and iron compounds represent the interesting 3D metal organophosphate molecular metamagnet due to spin canted antiferromagnetic with high critical temperature (40 K for Mn; 16 K for Fe). The infinite M–O–M layers are believed to be responsible for this high performance.     

Enhanced multiferroic properties in La and Ce co-doped BiFeO3 nanoparticles

Room temperature multiferroic properties of BiFeO₃ (BFO), Bi_0.9La_0.1FeO₃ ((La)BFO) and Bi_0.9La_0.075Ce_0.025FeO₃ ((La,Ce)BFO) nanoparticles have been reported in this paper. XRD (X-ray diffraction) analyses of the nanoparticles show a decrease in the lattice constants and cell volume with the substitution of La and Ce. It is evident from the SEM (scanning electron microscope) micrographs that the (La,Ce) co-doped sample possesses dense microstructure made of smaller particles. Raman study accounts for the weakening of the strong hybridization between Bi-O by the substitution of La and Ce ions. This is also accompanied by an increase in the remanent magnetization, dielectric constant, and ferroelectric polarization. BFO nanoparticles show exchange bias effect under an applied magnetic field while the (La)BFO and (La,Ce)BFO samples show no trace of such effect. Ac-conductivity of (La,Ce) co-doped sample is observed to be several orders lesser in magnitude than bulk BFO ceramics. These results are interpreted by means of the subtle change in the structure, suppression of the spin cycloid and reduction of oxygen vacancies in the doped samples.     

Hopping conductivity of Ni-doped p-CdSb in strong magnetic fields

Magnetoresistance (MR) of oriented single crystals of the anisotropic semiconductor p-CdSb doped with 2 at% of Ni is investigated between T=1.5 and 300 K in transversal pulsed magnetic fields up to B=30 T. In fields B∼4-15 T at T below 4.2 K, the resistivity obeys the law ln ρ∼η[B?(B)]^1/2 with ?(B)=a(0)/a(B), where a is the carrier localization radius and parameter η depends on a(0), on the acceptor concentration N_A and on the direction of the magnetic field with respect to the crystallographic axes, but does not depend on T. Such behavior gives evidence for MR realized by hopping charge transfer over the nearest-neighbor sites in strong magnetic field. The analysis of the experimental data yields the values of η, agreeing with calculated ones within an error of 10%, taking into account the effects of the anisotropy of the acceptor states and of the explicit dependence of a(B) due to the increase in the activation energy of shallow acceptors in magnetic field and the sensitivity of the metal-insulator transition to B.     

Effects of uniaxial pressure and annealing on the resistivity of Ba(Fe1−xCox)2As2

Single crystals of underdoped Ba(Fe_1−xCo_x)₂As₂ were detwinned by applying uniaxial pressure. The anisotropic in-plane resistivity was measured using the Montgomery method without releasing pressure. The resistivity along the a-axis shows metallic behavior down to 5 K, while the resistivity along the b-axis shows an insulator-like behavior in some temperature range. Annealing the sample radically reduces the residual resistivity for x=0, and at the same time the anisotropy becomes much smaller at low temperatures.     

Adiabatic small polaron-hopping conduction in Ln0.85Ca0.15MnO3 (Ln=Nd, Pr and Sm) perovskites

Polycrystalline bulk ferromagnetic insulating (FMI) Ln_0.85Ca_0.15MnO₃ (Ln=Nd, Pr and Sm) samples are prepared by standard solid-state reaction route and characterized. Powder X-ray diffraction (XRD) data of the manganites show single-phase character. Existing theoretical models predict that the high temperature (T>θ_D/2, θ_D being the Debye temperature) dc conductivity (σ_dc) of these samples is due to adiabatic small polaron-hopping conduction. Greaves’ and Mott's variable range hopping (VRH) conduction mechanisms are not suitable to explain the σ_dc data at low temperature (T<θ_D/2).     

Preparation, structure and oxide ion conductivity in Ce6−xYxMoO15−δ (x=0.1-1.4) solid solutions

The Ce_6−xY_xMoO_15−δ solid solution with fluorite-related structure have been characterized by differential thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), IR, Raman, scanning electric microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) methods. The electric conductivity of samples is investigated by Ac impedance spectroscopy. An essentially pure oxide-ion conductivity of the oxygen-deficiency was observed in pure argon, oxygen and air. The highest oxygen-ion conductivity was found in Ce_5.5Y_0.5MoO_15−δ ranging from 5.9×10⁻⁵ (S cm⁻¹) at 300 °C to 1.3×10⁻² (S cm⁻¹) at 650 °C, respectively. The oxide-ion conductivities remained stable over 80 h-long test at 800 °C. These properties suggested that significant oxide-ionic conductivity exists in these materials at moderately elevated temperatures.     

Defect structure and electrical properties of molybdenum disulphide

Electrical conductivity of molybdenum disulphide was studied in a helium-sulphur gas mixture as a function of temperature (1073-1273 K). It was found that over the whole temperature and sulphur pressure range (10-6600 Pa) studied, the material exhibits p-type conductivity. Based on literature intrinsic electronic disorder data as well as measured electrical conductivity results a defect model has been proposed. This model involves electron holes and doubly ionized interstitial sulphur ions as majority point defects as well as electrons and acceptor-type foreign ions as minority defects.     

Structural and magnetic ordering in the two-dimensional coordination polymer Co(ox)(bpy-d8), (ox=C2O4, bpy-d8=4,4′-bipyridine-d8)

Neutron diffraction and magnetic susceptibility studies of the two-dimensional coordination polymer Co(ox)(bpy-d8) are presented, where ox=C₂O₄²⁻ and bpy-d8=4,4′-bipyridine-d8 (fully deuterated). The neutron powder diffraction data reveal a second-order crystallographic phase transition at 290 K. Above 290 K, a disordered structure, space group Immm, is observed that is closely related to the ordered structure previously proposed on the basis of single crystal X-ray diffraction. At low temperatures, the structure is an ordered variant of the high-temperature phase with space group I222. In both phases, the Co ions are linked by the oxalate forming infinite chains that are crosslinked by the bpy ligands.The magnetic susceptibility follows qualitatively a quasi one-dimensional chain behavior. It exhibits a broad maximum around 35 K, corresponding to a strong antiferromagnetic coupling through the oxalate bridges. A kink at 9 K marks the onset of long-range antiferromagnetic ordering due to much weaker interchain magnetic interactions.The magnetically ordered structure determined from the low-temperature neutron diffraction data can be described with the propagation vector (1/2, 1/2, 1/2), i.e. a doubling of the unit cell in each principal direction. It is concluded that a significant antiferromagnetic interaction is mediated through the bpy ligands, although the Co-Co distance along these bridges is 11.4 Å.     

Influence of particle size and compaction pressure on the magnetic properties of iron-phenolic soft magnetic composites

This paper investigates the effect of particle size and compaction pressure on the magnetic properties of iron-phenolic soft magnetic composites (50 Hz-1000 kHz). The results showed that the optimum amount of phenolic resin to attain maximum permeability and minimum loss factor at 10 kHz is 0.7 wt% for samples containing iron powder with average particle size ∼150 μm compacted at 800 MPa. In accordance with this resin content, at high frequencies (>300 kHz), the sample with lower particle size ∼10 μm exhibits higher magnetic permeability, higher operating frequencies and lower imaginary part of permeability. With increase in the compaction pressure, specific resistivity decreases and imaginary and real parts of permeability increase at low frequencies.     

Impurity-induced magnetic order in the mixture of two spin gap systems (CH3)2CHNH3CuCl3 and (CH3)2CHNH3CuBr3

The ground state of the solid solution of the two spin gap systems (CH₃)₂CHNH₃CuCl₃ and (CH₃)₂CHNH₃CuBr₃ has been investigated by ¹H NMR. The existence of a magnetic ordering in the sample with the Cl-content x=0.85 was clearly demonstrated by a drastic splitting in a resonance line at low temperatures below T_N=13.5 K. The observed NMR spectra in the ordered state was qualitatively consistent with the simple antiferromagnetic state.     

Photocatalytic properties of lanthanide tungstates Ln2W2O9 (Ln=La,Pr, Nd,Sm, and Gd)

Lanthanide tungstates, Ln₂W₂O₉ (Ln=La, Pr, Nd, Sm, and Gd), were prepared via the polymerized complex method at 1273 K for 2 h, and their photocatalytic activities for hydrogen and oxygen evolution were investigated. Pt-loaded Gd₂W₂O₉ exhibited activity for H₂ evolution from an aqueous methanol solution under light irradiation (λ>300 nm). The remaining Ln₂W₂O₉ were inactive for H₂ evolution due to the influence of the Ln elements and their crystal structures. All Ln₂W₂O₉ were inactive for O₂ evolution from an aqueous AgNO₃ solution due to the lack of O₂ evolution sites on the surface.     

Non-stoichiometry effects on electrical and luminescence properties of the layered oxysulfide (LaO)CuS

The layered oxysulfide (LaO)CuS is a wide-gap semiconductor. In general, the wide-gap semiconductor has strong mono-polarity and non-stoichiometry which affect their physical properties. In this study, the relation between the non-stoichiometry of (LaO)CuS and their physical properties has been investigated. Several kinds of non-stoichiometric samples were prepared. In the Cu non-stoichiometry, (LaO)CuS can accommodate the excess Cu in preference to a deficiency. In the La and S non-stoichiometric samples, deficiencies are preferred. The Cu and S non-stoichiometry affects their electrical and emission properties as expected from the valence band structure. It should be noted that the La non-stoichiometry is also quite effective on the band edge emission and the resistivity as well as other non-stoichiometry. These results reveal that not only Cu but also La deficiency is important in controlling the physical properties.     

Frequency dependence of ionic conductivity and dielectric relaxation studies in Na3H(SO4)2 single crystal

Electrical impedance measurements of Na₃H(SO₄)₂ were performed as a function of both temperature and frequency. The electrical conductivity and dielectric relaxation have been evaluated. The temperature dependence of electrical conductivity reveals that the sample crystals transformed to the fast ionic state in the high temperature phase. The dynamical disordering of hydrogen and sodium atoms and the orientation of SO₄ tetrahedra results in fast ionic conductivity. In addition to the proton conduction, the possibility of a Na⁺ contribution to the conductivity in the high temperature phase is proposed. The frequency dependence of AC conductivity is proportional to ω^s. The value of the exponent, s, lies between 0.85 and 0.46 in the room temperature phase, whereas it remains almost constant, 0.6, in the high-temperature phase. The dielectric dispersion is examined using the modulus formalism. An Arrhenius-type behavior is observed when the crystal undergoes the structural phase transition.     

Phase stability in the LnCa2Mn2O7 (Ln=Pr, Nd, Sm and Gd) Ruddlesden-Popper series

The synthesis of the Ruddlesden-Popper series, LnCa₂Mn₂O₇, (Ln=Pr, Nd, Sm and Gd) is described and their structure and electronic properties investigated. The reduction in size of the A-site cation causes an increase in the distortion of their orthorhombic structures (space group Cmcm). All of these compounds form with a perovskite impurity, the amount of which increases on reduction of the cation size. The synthesis temperature also alters the amount of perovskite impurity in the phase, but only to a lower limit, implying the perovskite phase is intrinsic to the material and that a phase equilibrium exists between the layered Ruddlesden-Popper and perovskite phases, which is controlled by the cation size. The magnetic susceptibility show transitions characteristic of the perovskite phase, therefore little direct information can be obtained about the Ruddlesden-Popper phases, except that ferromagnetism is not observed in any of these materials.     

Electronic and high pressure elastic properties of RECd and REHg (RE=Sc,La and Yb) intermetallic compounds

Structural, electronic, elastic and mechanical properties of Cd and Hg based rare earth intermetallics (RECd and REHg; RE=Sc, La and Yb) have been investigated using the full-potential linearized augmented plane-wave (FP-LAPW) method within the density-functional theory (DFT). The ground state properties such as lattice constant (a₀), bulk modulus (B) and its pressure derivative (B′) have been obtained using optimization method and are found in good agreement with the available experimental results. The calculated enthalpy of formation shows that LaHg has the strongest alloying ability and structural stability. The electronic band structures and density of states reveal the metallic character of these compounds. The structural stability mechanism is also explained through the electronic structures of these compounds. The chemical bonding between rare earth atoms and Cd, Hg is interpreted by the charge density plots along (1 1 0) direction. The elastic constants are predicted from which all the related mechanical properties like Poisson’s ratio (σ), Young’s modulus (E), shear modulus (G_H) and anisotropy factor (A) are calculated. The ductility/brittleness of these intermetallics is predicted. Chen’s method has been used to predict the Vicker’s hardness of RECd and REHg compounds. The pressure variation of the elastic constants is also reported in their B₂ phase.     

YB48 the metal rich boundary of YB66; crystal growth and thermoelectric properties

It was discovered that the well-known higher boride YB₆₆, one of the first reported phonon glass electron crystals (PGEC), could be obtained in a much more metal-rich composition than previously thought possible. Using the floating zone growth method, YB₄₈ single crystals with YB₆₆ crystal structure could be obtained, and their thermoelectric properties measured. This expansion of the homogeneity range of the well-known YB₆₆ compound is surprising and a new Y atomic site was discovered. YB₄₈ exhibits much higher power factors than YB₆₆ which increase rapidly with increasing temperature. The obtained dimensionless figure of merit of this compound at 990 K is approximately 30 times higher than that of previously reported YB₆₆ samples, and higher than any other pristine higher boride. This discovery reveals YB₄₈ as a promising high temperature thermoelectric material.