High-energy femtosecond Yb-doped all-fiber monolithic chirped-pulse amplifier at repetition rate of 1 MHz

A high-energy femtosecond all ytterbium fiber amplifier based on a chirped-pulse amplification(CPA) technique at a repetition rate of 1 MHz seeded by a dispersion-management mode-locked picosecond broadband oscillator is studied.We find that the compressed pulse duration is dependent on the amplified energy,the pulse duration of 804 fs corresponds to the maximum amplified energy of 10.5 μJ,while the shortest pulse duration of 424 fs corresponds to the amplified energy of 6.75 μJ.The measured energy fluctuation is approximately 0.46% root mean square(RMS) over 2 h.The low-cost femtosecond fiber laser source with super-stability will be widely used in industrial micromachines,medical therapy,and scientific studies.     

采用光谱展宽技术的钛宝石飞秒激光放大器

报道了飞秒激光啁啾脉冲放大器中的激光脉冲光谱展宽技术，实验中使用了几种光谱展宽元件，结果表明使用激光光谱展宽元件能有效地将飞秒激光脉冲 光谱展宽，抑制了飞秒激光放大器中常见的激光脉冲光谱增益窄化现象，从飞秒放大系统的振荡级输出28fs种子脉冲，放大后得到了重复频率为10Hz、峰值功率为1．6TW、脉冲宽度37．5fs的超短强飞秒激光脉冲 。     

Generation of high-contrast and high-intensity laser pulses using an OPCPA preamplifier in a double CPA, Ti:sapphire laser system

We demonstrate a high-contrast, high-intensity double chirped-pulse amplification (CPA) Ti:sapphire laser system using an optical parametric chirped-pulse (OPCPA) pre- amplifier. By injecting cleaned microjoule seed pulses into the OPCPA, a temporal contrast greater than 10¹⁰ within picosecond times before the main femtosecond pulse is demonstrated with an output pulse energy of 1.7 J and a pulse duration of 30 fs, corresponding to a peak power of 60 TW at a 10 Hz repetition rate. This system uses a cryogenically-cooled Ti:sapphire final amplifier and generates focused peak intensities in excess of 10²⁰ W/cm².     

飞秒超强激光多通预放大过程中的脉冲信噪比研究

从啁啾脉冲放大的基本理论出发,详细计算了啁啾脉冲在多通预放大中各个时间点的增益情况,并设计了一个十通预放大器进行了实验研究. 结果显示,在抽运通量为1.6 J/cm²的非饱和放大情况下,种子脉冲经过十通预放大之后信噪比由10^-5提高到10^-7. 这表明在非饱和抽运通量下,多通预放大器可以有效提高激光脉冲的信噪比. 关键词： 多通预放大 信噪比 飞秒钛宝石激光器     

无展宽器的高重复率钛宝石啁啾飞秒脉冲再生放大器的研究

通过优化放大腔结构参数和采用高光束质量的泵浦激光,依靠放大器腔内各个元件的色散展宽种子脉冲, 用钛宝石作为增益介质, 在低泵浦能量下, 实现了高光束质量,高稳定的中等能量的高重复率飞秒脉冲再生放大. 将钛宝石晶体离焦放置,有效的避免了光学损伤. 在1.1 mJ的绿光泵浦下, 获得了2 ps, 120 μJ, 重复频率为1 KHz, 光谱带宽7.8 nm的放大脉冲, 用石英棱镜对压缩可得到130 fs的激光脉冲.     

输出能量4mJ的1kHz飞秒掺钛蓝宝石激光再生放大研究

针对高能量千赫兹重复频率飞秒激光的应用需求,设计了一套采用线性再生腔结构的高效率飞秒钛宝石激光啁啾脉冲放大系统.通过优化腔型设计,在重复频率为1 kHz、单脉冲能量为20 mJ的527 nm激光抽运下,将展宽后的800 nm啁啾脉冲激光的能量放大到5.8 mJ,对应斜效率达到30.7%.进一步通过色散补偿压缩脉冲宽度,获得了单脉冲能量为4 mJ、脉冲宽度为45.7 fs的输出,稳定性测量表明激光的能量抖动仅为0.18%(均方根值).     

基于大基模体积的10mJ飞秒钛宝石激光再生放大器

文章报导了基于大基模体积的高能量飞秒钛宝石激光再生放大器的设计与实验研究,在重复频率10 Hz、抽运能量60 mJ的激励下,得到了单脉冲能量17.4 mJ的种子脉冲放大结果,压缩后的脉冲宽度为40.6 fs,能量为13.9 mJ.借助于此大基模体积再生腔,仅增加一级多通放大,实现了峰值功率达1.9 TW飞秒激光脉冲输出.结果表明,大模体积再生放大不仅降低了后续放大对抽运能量的要求,也可以单独压缩实现再生腔直接输出10 mJ量级的飞秒激光脉冲,是大能量高峰值功率飞秒激光系统的优质前端.     

High gain amplification of femtosecond pulses with low amplified spontaneous emission in a multipass dye cell

We present a multipass femtosecond amplifier pumped by a Nd-YAG laser where the gain medium is given by a variable length dye cell. This system allows amplification factors up to 5 · 10⁶ and output pulse energies of 150 J, while restricting the contribution of amplified spontaneous emission to 0.5% of the total output energy, without using any saturable absorber stage. A detailed study of the output pulsewidth as a function of the duration of the input chirped pulse is also presented.     

TW级Ti：Al2O3飞秒激光放大器

报道ＴＷ（１０＾１２Ｗ）级Ｔｉ：Ａｌ２Ｏ３飞秒激光放大器的研究，采用Ｔｉ：Ａｌ２Ｏ３自锁模激光振荡器和脉冲啁啾放大技术，获得了能量为８４ｍＪ，脉宽为７５ｆｓ的放大光脉冲，峰值功率达到ＴＷ量级。     

采用环形再生腔结构的飞秒激光啁啾脉冲放大研究

采用环形再生腔结构的啁啾脉冲放大技术方案, 在重复频率100 Hz,单脉冲能量33.1 mJ的532 nm激光抽运下, 从钛宝石激光中获得了单脉冲能量9.84 mJ的放大输出, 对应的斜效率达33.1%.在重复频率10 Hz的情况下, 同样获得了单脉冲能量为9.64 mJ, 对应斜效率达36.8%的高效率放大结果. 通过色散补偿压缩该啁啾激光脉冲后的单脉冲能量为6.36 mJ, 脉冲宽度为59.7 fs. 测量结果表明典型的能量不稳定度为1.85%. 关键词： 啁啾脉冲放大 再生放大 飞秒激光 环形腔     

可用于超精细加工的高重复率、高光束质量飞秒再生放大脉冲的产生研究

通过飞秒放大增益饱和理论及飞秒脉冲展宽的理论计算与分析，指出在优化放大腔结构参数及改变抽运光能量情况下，可以在省略展宽器基础上实现中等能量的飞秒脉冲再生放大.以此为依据，采用低抽运能量和放大腔中钛宝石晶体离焦技术，成功地进行了无展宽器的高重复率飞秒钛宝石再生放大及压缩技术的实验研究，并获得了高光束质量的飞秒放大光脉冲，放大光脉冲能量大于100μJ，重复频率为1kHz，光谱带宽7.7nm，压缩后脉宽500fs. 关键词： 飞秒光脉冲 再生放大 光束质量 增益饱和     

Optical waveguide writing with a diode-pumped femtosecond oscillator

Optical waveguide writing is demonstrated by means of a diode-pumped cavity-dumped Yb:glass femtosecond laser oscillator with a pulse energy of 270 nJ at a 166-kHz repetition rate. Waveguides realized on an Er:Yb-doped phosphate glass are almost perfectly mode matched to standard single-mode fibers at 1.55 microm and show a 1.2-dB net gain in a standard telecommunications amplifier setup. Waveguide writing with a compact femtosecond laser oscillator is an important step toward introducing this technique into an industrial context.     

Tunable mid-infrared,high-energy femtosecond laser source for glyco-protein structure analysis

We have developed a 6–12 μm mid-infrared (MIR) femtosecond laser source for glyco-protein structure analysis. The MIR femtosecond laser pulses are generated by a differential frequency generation (DFG) configuration with a combination of Ti:sapphire based regeneratively amplified femtosecond laser pulses (780 nm, 160 fs, 1 mJ) and a β-BaB₂O₄ (BBO) based optical parametric amplifier (OPA). The MIR pulse energy exceeds 4.5 μJ, where a glyco-protein molecule has resonant absorption lines due to the vibrational–rotational transitions. The pulse width is estimated to be less than 1 ps according to the cross correlation measurement between the two OPA output pulses. Using the MIR femtosecond laser pulses, we demonstrated photo-dissociation of the sialyl Lewis X (sLeX) proton added ion, which is the first time to the best of our knowledge. PACS 42.65.Re; 42.62.-b; 42.60.-b; 42.65.-k; 87.50     

100-TW femtosecond laser based on parametric amplification

In experiments on the parametrical amplification of femtosecond pulses in wide-aperture DKDP crystals, a power of more than 100 TW has been reached, which is much higher than the record level achieved in such lasers. The energy efficiency obtained for the parametric amplifier is equal to 27%. The energy of a 72-fs pulse is equal to 10 J.     

12-fs pulses from a continuous-wave-pumped 200-nJ Ti:sapphire amplifier at a variable repetition rate as high as 4 MHz

We demonstrate a novel compact femtosecond Ti:sapphire laser system operating at repetition rates from 10 kHz to 4 MHz. The scheme is based on the combination of a broadband cavity-dumped oscillator and a double-pass Ti:sapphire amplifier pumped by a low-noise cw solid-state laser. Amplified pulses with an extremely smooth spectrum, a duration of only 12 fs, and less than 0.25% rms fluctuation are generated in a beam with M2 < 1.2. A maximum pulse energy of 210 nJ and an average output power of as much as 720 mW are achieved. This output energy is sufficient to generate a stable continuum in a sapphire disk.     

THz generation via optical rectification with ultrashort laser pulse focused to a line

We report on efficient THz pulse generation via optical rectification with femtosecond laser pulses focused to a line by a cylindrical lens. This configuration provides phase-matched conditions in the superluminal regime. 35 pJ THz pulses have been generated with this technique in a stoichiometric LiNbO₃ crystal pumped by 2 μJ femtosecond laser pulses at room temperature. An unusual superquadratic rise of the THz pulse energy with the laser pulse energy has been observed at high laser energies. This extraordinary energy dependence of the THz generation efficiency is explained by self-focusing of the laser beam in the crystal. Z-scan measurements and comparison of the THz pulse spectra created with laser pulses having different energies confirm this interpretation.     

Fiber based high repetition rate, high energy laser source applying chirped pulse amplification

We demonstrate the potential of a high-gain Yb-fiber amplifier system to provide ultrashort pulses with high energies. 100 μJ pulses generated at a repetition rate of 32 kHz exhibit nearly diffraction limited output (M²≈1.7) at a 1060 nm center wavelength. Using chirped pulse amplification, temporally streched laser pulses from a femtosecond oscillator could be compressed after amplification to subpicosecond pulse duration. The achievable intensities are high enough to create plasmas which can efficiently convert laser light to the extreme ultraviolet radiation. In a multimode Yb-doped fiber amplifier we obtained average powers of up to 22 W and single pulse energies up to 130 μJ.     

100 W全光纤声光调Q光纤激光器实验研究

 报道了一台全光纤结构主振荡功率放大(MOPA)型掺镱脉冲光纤激光器,以光纤光栅为腔镜,光纤型声光调Q的光纤激光器为种子源,通过两级掺镱双包层光纤放大器实现功率放大。对声光调Q的光纤激光器输出特性进行了研究,比较了不同泵浦波长、不同重复频率对激光输出功率和脉冲宽度的影响,并实现了最短脉冲宽度25 ns、单脉冲能量45 μJ的脉冲激光输出。在重复频率50 kHz时,对脉冲宽度130 ns、平均功率0.6 W的种子光进行放大,得到了平均功率102.5 W、脉冲宽度约240 ns的激光输出。     

用于宽带啁啾脉冲光参量放大系统精确同步的新方法

基于非共线光参量放大,以波长800 nm飞秒激光的倍频光为抽运光,以激光二极管640 nm连续波激光为信号光,产生了与800 nm飞秒激光精确同步的无直流本底的1064 nm脉冲光。实验结果显示该1064 nm的光脉冲在脉冲能量和空间光束质量上均可作为1064 nm波长脉冲放大器的种子光。仅通过一级简单紧凑的非共线参量放大就可实现光周期量级的光参量啁啾脉冲放大系统的抽运激光和种子光的精确同步。     

Initial testing of a high-repetition-rate electron-beam-pumped KrF laser amplifier

The initial test results of the high-repetition-rate (rep-rate) electron-beam (e-beam) pumped KrF laser amplifier under development in our laboratory are reported. This amplifier is aimed at producing a laser energy of 20 J per pulse at a rep rate of 1 Hz. Thus far, 700 consecutive e-beampulses (250 kV, 270 J/pulse) were generated at a rep rate of 1 Hz. The laser gas was repetitively pumped by the e-beams injected through the water-cooled diaphragm foils. Received: 5 February 2001 / Published online: 21 March 2001