Grafting acrylic polymers from flat nickel and copper surfaces by surface-initiated atom transfer radical polymerization

Acrylic polymers, including poly(methyl methacrylate), poly(2,2,2-trifluoroethyl methacrylate), poly( N,N'-dimethyaminoethyl methacrylate), and poly(2-hydroxyethyl methacrylate) were grafted from flat nickel and copper surfaces through surface-initiated atom transfer radical polymerization (ATRP). For the nickel system, there was a linear relationship between polymer layer thickness and monomer conversion or molecular weight of "free" polymers. The thickness of the polymer brush films was greater than 80 nm after 6 h of reaction time. The grafting density was estimated to be 0.40 chains/nm2. The "living" chain ends of grafted polymers were still active and initiated the growth of a second block of polymer. Block copolymer brushes with different block sequences were successfully prepared. The experimental surface chemical compositions as measured by X-ray photoelectron spectroscopy agreed very well with their theoretical values. Water contact angle measurements further confirmed the successful grafting of polymers from nickel and copper surfaces. The surface morphologies of all samples were studied by atomic force microscopy. This study provided a novel approach to prepare stable functional polymer coatings on reactive metal surfaces.     

Polymer‐Infiltrated Aligned Carbon Nanotube Fibers by in situ Polymerization

Carbon nanotube–polymer composite fibers are obtained by infiltration of a monomer liquid into aligned carbon nanotube aerogel fibers with subsequent in situ polymerization. The monomer, methyl methacrylate (MMA), was infiltrated into the aerogel fibers of multi‐walled carbon nanotubes (MWNTs) at room temperature and subsequently polymerized at 50 °C into poly(methyl methacrylate) (PMMA). Cross‐sections of the PMMA/MWNT composite fibers showed that the PMMA filled the spaces of the nanotube fibers and bound the nanotubes together. PMMA in the composite fibers exhibited local order. The resultant composite fibers with 15 wt.‐% nanotube loading exhibited a 16‐fold and a 49‐fold increase in tensile strength and Young's modulus, respectively, compared to the control PMMA.

     

A FACILE APPROACH FOR THE SURFACE MODIFICATION OF POLY(VINYLIDENE FLUORIDE) MEMBRANE VIA SURFACE-INITIATED ATOM TRANSFER RADICAL POLYMERIZATION

A novel approach for the surface modification of poly(vinylidene fluoride)(PVDF)membrane was successfully realized through alkaline treatment,UV-induced bromine addition,and followed by surface-initiated atom transfer radical polymerization(ATRP)of methyl methacrylate(MMA).Chemical changes on the PVDF membrane before and after modification were analyzed with attenuated total reflectance Fourier transform infrared spectroscopy(ATR/FT-IR)and X-ray photoelectron spectroscopy(XPS).Primary kinetic study revea...     

A FACILE APPROAC0H FOR THE SURFACE MODIFICATION OF POLY(VINYLIDENE FLUORIDE)MEMBRANE VIA SURFACE-INITIATED ATOM TRANSFER RADICAL POLYMERIZATION

A novel approach for the surface modification of poly(vinylidene fluoride)(PVDF)membrane was successfully realized through alkaline treatment,UV-induced bromine addition,and followed by surface-initiated atom transfer radical polymerization(ATRP)of methyl methacrylate(MMA).Chemical changes on the PVDF membrane before and after modification were analyzed with attenuated total reflectance Fourier transform infrared spectroscopy(AIR/Fr-IR)and X-ray photoelectron spectroscopy(XPS).Primary kinetic study revealed that the chain growth of poly(methyl methacrylate)(PMMA)from the PVDF surface is consistent with a"controlled"process.     

Grafting Efficiency of Hydroxy‐Terminated Poly(methyl methacrylate) with Multiwalled Carbon Nanotubes

Summary: Poly(methyl methacrylate)s (PMMAs) containing a terminal hydroxy group or multiple hydroxy groups as pendants were grafted to multiwalled carbon nanotubes (MWNTs) by esterification in toluene at 100 °C. The recovered polymer with a low level of MWNTs and the PMMA‐g‐MWNTs with up to 12 wt.‐% grafted polymer were characterized using spectroscopic, microscopic, and thermogravimetric analyses. The percentage of polymer present in the PMMA‐g‐MWNT samples is very low based upon the concentration of the acid groups in the tubes.

The grafting of hydroxy‐terminated PMMA to MWNTs by esterification.     

Highly enhanced electrical and mechanical properties of methyl methacrylate modified natural rubber filled with multiwalled carbon nanotubes

Developing conductive networks in a polymer matrix with a low percolation threshold and excellent mechanical properties is desired for soft electronics applications. In this work, natural rubber (NR) functionalized with poly(methyl methacrylate) (PMMA) was prepared for strong interfacial interactions with multiwalled carbon nanotubes (MWCNT), resulting in excellent performance of the natural rubber nanocomposites. The MWCNT and methyl methacrylate functional groups gave good filler dispersion, conductivity and tensile properties. The filler network in the matrix was studied with microscopy and from its non-linear viscoelasticity. The Maier-Göritze approach revealed that MWCNT network formation was favored in the NR functionalized with PMMA, with reduced electrical and mechanical percolation thresholds. The obvious improvement in physical performance of MWCNT/methyl methacrylate functionalized natural rubber nanocomposites was caused by interfacial interactions and reduced filler agglomeration in the NR matrix. The modification of NR with poly(methyl methacrylate) and MWCNT filler was demonstrated as an effective pathway to enhance the mechanical and electrical properties of natural rubber nanocomposites.     

Compatibility studies on solutions of polymer blends by viscometric and ultrasonic techniques

Detailed viscometric and ultrasonic velocity studies have been conducted on solutions of blends of poly(methyl methacrylate) with poly(vinyl acetate), poly(vinyl chloride) with poly(vinyl acetate) and poly(methyl methacrylate) with polystyrene over an extended range of concentrations and temperatures in toluene, chlorobenzene and toluene respectively. The plots of both absolute viscosity and ultrasonic velocity vs composition deviate from linearity according to the degree of compatibility of polymer blends, at all concentrations and temperatures. The curves for compatible systems are linear. These investigations offer an entirely new approach to the study of the compatibility of polymer blends.     

Supramolecular Self‐Assembly of Polymer‐Functionalized Carbon Nanotubes on Surfaces

Summary: Supramolecular self‐assembly of poly(methyl methacrylate)‐grafted multiwalled carbon nanotubes (MWNT‐g‐PMMA) was reported herein. The MWNT‐g‐PMMA (85 wt.‐% PMMA) dispersed in tetrahydrofuran could self‐assemble into suprastructures on surfaces such as gold, mica, silicon, quartz, or carbon films. With decreasing concentration of the MWNT‐g‐PMMA from 3 to 0.1 mg · mL⁻¹, the assembled structures changed from cellular and basketwork‐like forms to multilayer cellular networks and individual needles. SEM, AFM, and TEM measurements confirmed the morphology of the assembled suprastructures, and revealed the assembly mechanism. Phase separation during evaporation of the solvent drives the MWNT‐g‐PMMA nanohybrids to assemble and form the suprastructures, and the rigid MWNTs stabilize the structures.

SEM images of self‐assembled suprastructures of basketwork (a), cellular network (b), and needles (c) from the THF solution of the PMMA‐grafted MWNTs on gold surface.     

Thermal degradation of copolymers of methyl methacrylate and methyl acrylate. I. Products and general characteristics of the reaction

The technique of thermal volatilization analysis (TVA), applied to methyl methacrylate–methyl acrylate copolymers having molar composition ratios 112/1, 26/1, 7.7/1, and 2/1, has demonstrated that the stabilization of poly(methyl methacrylate) by copolymerized methyl acrylate is due to inhibition of the depolymerization initiated at terminally unsaturated structures, probably by direct blockage by methyl acrylate units. The molecular weight of the copolymers decreases rapidly during degradation, suggesting that a random scission process is involved. The products of degradation consist of the monomers, carbon dioxide, chain fragments larger than monomer, and a permanent gas fraction which is principally hydrogen. Infrared and ultraviolet spectral measurements suggest that the residual polymer, which is colored, incorporates carbon–carbon unsaturation. The complete absence of methanol among the products is surprising in view of its abundance among the products of degradation of poly(methyl acrylate). These observations have been accounted for qualitatively in terms of acceptable polymer behavior.     

Electrorheology of Multiwalled Carbon Nanotube/Poly(methyl methacrylate) Nanocomposites

Summary: Multiwalled carbon nanotube (MWNT) nanocomposites dispersed in a poly(methyl methacrylate) (PMMA) matrix were prepared via suspension polymerization, in which radicals induced on the outer wall of the MWNTs by 2,2′‐azoisobutyronitrile initiate the grafting of PMMA. The synthesized MWNT/PMMA nanocomposite particles were found to have a spherical shape and exhibit a high electrical conductivity, mainly as a result of the carbon nanotubes. A suspension was prepared with MWNT/PMMA particles in insulating silicone oil and its electrorheological properties were investigated by controlling applied direct current (DC) electric field strengths.

Flow curve possessing a region analogous to the coexistence curve.     

聚丙烯酸功能化多壁碳纳米管

Covalent functionalization of multiwalled carbon nanotubes （MWNT） with poly（acrylic acid） has been successfully achieved via grafting of poly（acryloyl chloride） on nanotube surface by esterification reaction of acyl chloride-bound polymer with hydroxyl functional groups present on acid-oxidized MWNT and hydrolysis of polymer attached to nanotubes. Polymer-functionalized MWNT could possess remarkably high solubility in water, and their aqueous solution was very stable without any observable black deposit for a long time. Characterizations of such functionalized MWNT samples using Fourier transform infrared spectrometer, transmission electron microscopy and nuclear magnetic resonance techniques indicated that poly（acrylic acid） was covalently attached to the surface of MWNT.     

Silica nanoparticle covered with mixed polymer brushes as Janus particles at water/oil interface

Silica nanoparticles (NSiO₂) are modified with mixed polymer brushes derived from a block copolymer precursor, poly(methyl methacrylate)-b-poly(glycidyl methacrylate)-b-poly(tert-butyl methacrylate) with short middle segment of PGMA, through one step ??grafting-onto?? approach. The block polymer precursors are prepared via reversible addition?Cfragmentation chain transfer-based polymerization of methyl methacrylate, glycidyl methacrylate, and tert-butyl methacrylate. The grafting is achieved by the reaction of epoxy group in short PGMA segment with silanol functionality of silica. After hydrolysis of poly(tert-butyl methacrylate) segment, amphiphilic NSiO₂ with ??V-shaped?? polymer brushes possessing exact 1:1 molar ratio of different arms were prepared. The functionalized particles self-assemble at oil/water interfaces to form stable large droplets with average diameter ranging from 0.15?±?0.06 to 2.6?±?0.75?mm. The amphiphilicity of the particles can be finely tuned by changing the relative lengths of poly(methyl methacrylate) and poly(methacrylic acid) segments, resulting in different assembly behavior. The method may serve as a general way to control the surface property of the particles.     

A new method for estimation of viscosity-average molecular weight of polymers from GPC

A novel approach for the determination of the viscosity-average molecular weight of polymers for which Mark–Houwink constants are not known is presented. This method can be applied to narrow as well as broad-molecular-weight-distribution polymer samples and requires only the GPC chromatogram and viscosity data. The proposed method was tested using polystyrene and poly(methyl methacrylate) in toluene and THF. Molecular weights computed by the proposed approach are in good agreement with those obtained using conventional techniques.     

Incorporation of silver/carbon nanoparticles into poly(methyl methacrylate) via in situ miniemulsion polymerization and its influence on the glass‐transition temperature

Silver/carbon nanoparticles (9 nm) were incorporated, as reinforcements, into a matrix of poly(methyl methacrylate) via in situ miniemulsion polymerization. It was found by differential scanning calorimetry that the glass‐transition temperature of the poly(methyl methacrylate) showed an improvement of 14 °C with only 0.5 wt % nanoparticles in comparison with a pure poly(methyl methacrylate) control, which was also obtained by miniemulsion polymerization under the same conditions. This increase was related to a polymer chain mobility restriction due to a combination of bound plastic and joint plastic shell effects at the interphase and the surrounding regions. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 511–518, 2007.     

Local molecular dynamics of poly(ethylene glycol) dimethacrylate synthesized in the presence of branched poly(methyl methacrylate): a photochromic probe study

The local molecular dynamics and morphology of poly(ethylene glycol) dimethacrylate networks synthesized in the presence of 0–40% branched poly(methyl methacrylate) were studied using a photochromic probe (6-nitrospiropyran). The change in the free volume of the polymer in the vicinity of the photochromic probe was monitored by the rate of dark bleaching of merocyanine (colored form of 6-nitrospiropyran). The local free volume and the mobility of the polymer chain fragments decrease as the conversion of C=C bonds and the content of branched poly(methyl methacrylate) in the polymer increase.     

Thermal degradation of phenyl methacrylate-methyl methacrylate copolymers

The degradation behaviours of poly(phenyl methacrylate), four phenyl methacrylate-methyl methacrylate copolymers which span the composition range, and poly(methyl methacrylate) have been compared by using thermogravimetry in dynamic nitrogen and thermal volatilisation analysis (TVA) under vacuum, with programmed heating at 10°C/min. Volatile products have been separated by subambient TVA and identified and the cold ring fraction and partially degraded polymer have been examined by ir spectroscopy. Poly(phenyl methacrylate) resembles poly(methyl methacrylate) in degrading completely to monomer. Copolymers of phenyl methacrylate and methyl methacrylate are more stable than the homopolymers. On degradation, the major products are the two monomers. Minor products from all the copolymers include carbon dioxide, dimethylketene, isobutene and formaldehyde. Copolymers with low and moderate phenyl methacrylate contents show the formation of anhydride ring structures in the cold ring fraction and partially degraded copolymer, together with small amounts of methanol in the volatile products. Carbon dioxide is a more significant product at lower phenyl methacrylate contents.The mechanism of degradation is discussed.     

A predictive approach based on the Simha–Somcynsky free‐volume theory for the effect of dissolved gas on viscosity and glass transition temperature of polymeric mixtures

The gas concentration and pressure effects on the shear viscosity of molten polymers were modeled by using a unified approach based on a free volume theory. A concentration and pressure dependent “shift factor,” which accounts for free volume changes associated with polymer‐gas mixing and with variation of absolute pressure as well as for dilution effects, has been herein used to scale the pure polymer viscosity, as evaluated at the same temperature and atmospheric pressure. The expression of the free volume of the polymer/gas mixture was obtained by using the Simha and Somcynsky equation of state for multicomponent fluids. Experimental shear viscosity data, obtained for poly(ε‐caprolactone) with nitrogen and carbon dioxide were successfully predicted by using this approach. Good agreement with predictions was also found in the case of viscosity data reported in the literature for polystyrene and poly(dimethylsiloxane) with carbon dioxide. Free volume arguments have also been used to predict the T_g depression for polystyrene/carbon dioxide and for poly(methyl methacrylate)/carbon dioxide mixtures, based on calculations performed, again, with the Simha and Somcynsky theory. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1863–1873, 2006     

Microhardness measurements of poly(methyl methacrylate) and poly(vinylidene fluoride) polyblends

The preparation of polymer blends of poly(methyl methacrylate) and poly(vinylidene fluoride) in different weight percentages is described. Vickers microhardness measurements have been made to study the effects of load and compositional ratio of the two polymers in polyblend. It is observed that poly(vinylidene fluoride) acts as a plasticizer for poly(methyl methacrylate). Evidence of increasing and decreasing strength of polyblends has been obtained for different compositional ratios of the two polymers.     

Liquid chromatography of polymer mixtures applying a combination of exclusion and full adsorption mechanisms. 5. Six-component blends of chemically similar polymers

The separation of six-component blends of chemically similar homopolymers utilising the full adsorption-desorption (FAD) process is presented. The main advantage of the FAD approach over other methods represents the successive and independent size- exclusion chromatography (SEC) characterisation of all blend components. The method is based on the full adsorption and retention of all n or n−1 components of the polymer blend from an adsorption promoting liquid (ADSORLI) in a small FAD column. Nonadsorbed macromolecules are forwarded directly into SEC for molecular characterisation. Next, appropriate displacers are successively applied to the FAD column to selectively release preadsorbed blend constituents into the on-line SEC column. Dynamic integral desorption isotherms for single constituents, as well as for polymer blends to be analysed, allow identification of optimal displacer compositions to release just one kind of macromolecule. Model polymer blends containing polystyrene (PS), poly(lauryl methacrylate), poly(butyl methacrylate), poly(ethyl methacrylate), poly(methyl methacrylate) and poly(ethylene oxide) (PEO) or, alternatively, PS, poly(2-ethylhexyl acrylate), poly(butyl acrylate), poly(ethyl acrylate), poly(methyl acrylate) and PEO of similar molar masses can be separated and characterised in one multistep run using nonporous silica FAD packing, toluene as an ADSORLI and its mixtures with a desorption promoting liquid such as ethyl acetate, tetrahydrofuran or dimetylformamide to form displacers with appropriate desorption strength. Received: 9 September 1998 Accepted in revised form: 16 November 1998     

Hot embossing and thermal bonding of poly(methyl methacrylate) microfluidic chips using positive temperature coefficient ceramic heater

As a self-regulating heating device, positive temperature coefficient ceramic heater was employed for hot embossing and thermal bonding of poly(methyl methacrylate) microfluidic chip because it supplied constant-temperature heating without electrical control circuits. To emboss a channel plate, a piece of poly(methyl methacrylate) plate was sandwiched between a template and a microscopic glass slide on a positive temperature coefficient ceramic heater. All the assembled components were pressed between two elastic press heads of a spring-driven press while a voltage was applied to the heater for 10 min. Subsequently, the embossed poly(methyl methacrylate) plate bearing negative relief of channel networks was bonded with a piece of poly(methyl methacrylate) cover sheet to obtain a complete microchip using a positive temperature coefficient ceramic heater and a spring-driven press. High quality microfluidic chips fabricated by using the novel embossing/bonding device were successfully applied in the electrophoretic separation of three cations. Positive temperature coefficient ceramic heater indicates great promise for the low-cost production of poly(methyl methacrylate) microchips and should find wide applications in the fabrication of other thermoplastic polymer microfluidic devices.