Reversible addition fragmentation chain transfer polymerization of sterically hindered monomers: Toward well‐defined rod/coil architectures

The sterically hindered monomers dibutyl itaconate (DBI) and dicyclohexyl itaconate (DCHI) were polymerized via reversible addition fragmentation chain transfer (RAFT) free‐radical polymerization. S,S′‐Bis(α,α′‐dimethyl‐α″‐acetic acid) trithiocarbonate, cumyl dithiobenzoate, and cumyl phenyldithioacetate have been used as RAFT agents to mediate a series of polymerizations at 65 °C yielding rod polymers ranging in number average molecular weight from 9000 to 92,000 g mol^?1. The progress of the polymerization was followed via online Fourier transform–near infrared spectroscopy. The polydispersity indices of the obtained rod polymers were relatively high at 1.4–1.7. The RAFT polymerizations of the hindered monomers used in the present study displayed both ideal living and hybrid behavior between conventional and living polymerization, depending on the RAFT agent used. DCHI rod polymers generated via the RAFT process were subsequently reinitiated in the presence of styrene to produce a range of BAAB and A‐B rod‐coil block copolymers of molecular weights up to 164,000 g mol^?1. The chain extension yields molecular weight distributions that progressively shift to higher molecular weights and are unimodal. Thermogravimetric analysis of the pDCHI‐block‐pStyrene copolymers indicates thermal degradation in two separate steps for the pDCHI and pStyrene blocks. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2432–2443, 2004     

Kinetic model of reversible addition‐fragmentation chain transfer polymerization in microemulsions

A simplified kinetic model for RAFT microemulsion polymerization has been developed to facilitate the investigation of the effects of slow fragmentation of the intermediate macro‐RAFT radical, termination reactions, and diffusion rate of the chain transfer agent to the locus of polymerization on the control of the polymerization and the rate of monomer conversion. This simplified model captures the experimentally observed decrease in the rate of polymerization, and the shift of the rate maximum to conversions less than the 39% conversion predicted by the Morgan model for uncontrolled microemulsion polymerizations. The model shows that the short, but finite, lifetime of the intermediate macro‐RAFT radical (1.3 × 10^?4–1.3 × 10^?2 s) causes the observed rate retardation in RAFT microemulsion polymerizations of butyl acrylate with the chain transfer agent methyl‐2‐(O‐ethylxanthyl)propionate. The calculated magnitude of the fragmentation rate constant (k_f = 4.0 × 10¹–4.0 × 10³ s^?1) is greater than the literature values for bulk RAFT polymerizations that only consider slow fragmentation of the macro‐RAFT radical and not termination (k_f = 10^?2 s^?1). This is consistent with the finding that slow fragmentation promotes biradical termination in RAFT microemulsion polymerizations. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 604–613, 2010     

Synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers by combining ATRP and RAFT polymerizations

The synthesis of poly(tert‐butyl acrylate‐block‐vinyl acetate) copolymers using a combination of two living radical polymerization techniques, atom transfer radical polymerization (ATRP) and reversible addition‐fragmentation chain transfer (RAFT) polymerization, is reported. The use of two methods is due to the disparity in reactivity of the two monomers, viz. vinyl acetate is difficult to polymerize via ATRP, and a suitable RAFT agent that can control the polymerization of vinyl acetate is typically unable to control the polymerization of tert‐butyl acrylate. Thus, ATRP was performed to make poly(tert‐butyl acrylate) containing a bromine end group. This end group was subsequently substituted with a xanthate moiety. Various spectroscopic methods were used to confirm the substitution. The poly(tert‐butyl acrylate) macro‐RAFT agent was then used to produce (tert‐butyl acrylate‐block‐vinyl acetate). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7200–7206, 2008     

Reaction control in radical polymerization of di‐n‐butyl itaconate utilizing a hydrogen‐bonding interaction

We have reported that intramolecular chain‐transfer reaction takes place in radical polymerization of itaconates at high temperatures and/or at low monomer concentrations. In this article, radical polymerizations of di‐n‐butyl itaconate (DBI) were carried out in toluene at 60 °C in the presence of amide compounds. The ¹³C‐NMR spectra of the obtained poly(DBI)s indicated that the intramolecular chain‐transfer reaction was suppressed as compared with in the absence of amide compounds. The NMR analysis of DBI and N‐ethylacetamide demonstrated both 1:1 complex and 1:2 complex were formed at 60 °C through a hydrogen‐bonding interaction. The ESR analysis of radical polymerization of diisopropyl itaconate (DiPI) was conducted in addition to the NMR analysis of the obtained poly(DiPI). It was suggested that the suppression of the intramolecular chain‐transfer reaction with the hydrogen‐bonding interaction was achieved by controlling the conformation of the side chain at the penultimate monomeric unit of the propagating radical with an isotactic stereosequence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4895–4905, 2004     

Reversible addition–fragmentation chain‐transfer polymerization: Unambiguous end‐group assignment via electrospray ionization mass spectrometry

Electrospray ionization mass spectrometry was performed to identify the structure of polymeric methyl acrylates generated via the cumyl dithiobenzoate (CDB), cumyl p‐fluorodithiobenzoate (CPFDB), and 1‐phenylethyl dithiobenzoate (PEDB) mediated reversible addition–fragmentation chain‐transfer (RAFT) polymerizations. The relatively simple spectra clearly demonstrate the end groups of this living free‐radical polymerization technique. Only polymeric chains carrying one leaving group of the RAFT agent and the dithiobenzoate end group as the active RAFT center were discovered. Multiple‐stage mass spectrometric experiments and oxidation of the dithioester end group confirmed the structure of the generated polymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4032–4037, 2002     

Chain‐transfer reaction in the radical polymerization of di‐n‐butyl itaconate at high temperatures

Radical polymerizations of di‐n‐butyl itaconate were investigated. Unexpected resonances (C resonances) were observed in ¹³C NMR spectra of C?O of poly(di‐n‐butyl itaconate)s [poly(DBI)s] obtained at temperatures higher than 60 °C, although two kinds of carbonyl groups showed splittings due to triad tacticities in the spectra of polymers obtained at lower temperatures. The poly(DBI)s formed by the different kinds of initiators or formed in the presence of chain‐transfer agents showed hardly any changes in the intensities of the C resonances; this indicated that the C resonances were not due to the structures formed through initiating and terminating reactions. The poly(DBI)s obtained at different yields showed only a slight increase in the intensities of the C resonances with the yield, which suggested that the C resonances were not attributable to the intermolecular chain‐transfer reaction to the monomer and/or polymer. However, the intensities of the C resonances significantly increased with a decreasing feed monomer concentration; this suggested that intramolecular chain‐transfer reactions took place at high temperatures. Furthermore, a Cu complex‐catalyzed atom transfer radical polymerization mechanism was revealed to be effective for suppressing the intramolecular chain‐transfer reaction at 60 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2415–2426, 2002     

Synthesis of comb‐like polystyrene with poly(N‐phenyl maleimide‐alt‐p‐chloromethyl styrene) as macroinitiator

The copolymerization of N‐phenyl maleimide and p‐chloromethyl styrene via reversible addition–fragmentation chain transfer (RAFT) process with AIBN as initiator and 2‐(ethoxycarbonyl)prop‐2‐yl dithiobenzoate as RAFT agent produced copolymers with alternating structure, controlled molecular weights, and narrow molecular weight distributions. Using poly(N‐phenyl maleimide‐alt‐p‐chloromethyl styrene) as the macroinitiator for atom transfer radical polymerization of styrene in the presence of CuCl/2,2′‐bipyridine, well‐defined comb‐like polymers with one graft chain for every two monomer units of backbone polymer were obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2069–2075, 2006     

Narrow disperse polymers using amine functionalized dithiobenzoate RAFT agent and easy removal of thiocarbonyl end group from the resultant polymers

A novel amine functionalized RAFT agent, 2‐cyanoprop‐2‐yl(4‐N,N‐dimethylaminophenyl) dithiobenzoate has been synthesized and used to control the polymerization of vinyl monomers. This dithiobenzoate RAFT agent, although air sensitive, controlled the polymerization of MMA and St very well in an inert atmosphere and the polymerization results obtained were marginally better than using the most popular 2‐cyanoprop‐2‐yl dithiobenzoate RAFT agent. The living nature of these polymerizations was confirmed by kinetics study and chain extension reactions to yield narrow disperse di‐block copolymers. Most importantly, use of this novel RAFT agent simplified the removal procedure of the color causing end thiocarbonyl group from the RAFT derived polymers and thereby leading to polymers with improved appearance. The removal of end group from the polymer was confirmed by ¹H NMR and UV‐vis spectroscopic techniques. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A strategy for synthesis of ion‐bonded amphiphilic miktoarm star copolymers via supramolecular macro‐RAFT agent

Amphiphilic supramolecular miktoarm star copolymers linked by ionic bonds with controlled molecular weight and low polydispersity have been successfully synthesized via reversible addition‐fragmentation chain transfer (RAFT) polymerization using an ion‐bonded macromolecular RAFT agent (macro‐RAFT agent). Firstly, a new tetrafunctional initiator, dimethyl 4,6‐bis(bromomethyl)‐isophthalate, was synthesized and used as an initiator for atom transfer radical polymerization (ATRP) of styrene to form polystyrene (PSt) containing two ester groups at the middle of polymer chain. Then, the ester groups were converted into tertiary amino groups and the ion‐bonded supramolecular macro‐RAFT agent was obtained through the interaction between the tertiary amino group and 2‐dodecylsulfanylthiocarbonylsulfanyl‐2‐methyl propionic acid (DMP). Finally, ion‐bonded amphiphilic miktoarm star copolymer, (PSt)₂‐poly(N‐isopropyl‐acrylamide)₂, was prepared by RAFT polymerization of N‐isopropylacrylamide (NIPAM) in the presence of the supramolecular macro‐RAFT agent. The polymerization kinetics was investigated and the molecular weight and the architecture of the resulting star polymers were characterized by means of ¹H‐NMR, FTIR, and GPC techniques. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5805–5815, 2008     

Synthesis of well‐designed polymers carrying saccharide moieties via RAFT miniemulsion polymerization

Two hydrophobic vinyl saccharide monomers based on D ‐glucose and D ‐fructose were polymerized by employing the reversible addition‐fragmentation transfer (RAFT) miniemulsion polymerization technique to prepare well‐designed glycopolymers. Three dithiobenzoate‐RAFT agents [S?C(Ph)S? R], 1‐phenylethyl dithiobenzoate (PED), 2‐phenylprop‐2‐yl dithiobenzoate (PPD), and 2‐cyanoprop‐2‐yl dithiobenzoate (CPD), were used to control the growth of polymer chains. The best results were obtained in the presence of the PPD‐RAFT agent and the formed polymers have polydispersity index's (PDI) lower than 1.15. Under adequate miniemulsion polymerization conditions, a glycopolymer with PDI of 1.1 and molecular weight of 5 × 10⁴ g/mol has been successfully synthesized in a short reaction time of 100 min. Furthermore, some block copolymers containing saccharide segment with butyl or methyl methacrylate were prepared. Copyright © 2007 John Wiley & Sons, Ltd.     

R‐RAFT approach for the polymerization of N‐isopropylacrylamide with a star poly(ε‐caprolactone) core

Reversible addition‐fragmentation chain transfer (RAFT) polymerization is a more robust and versatile approach than other living free radical polymerization methods, providing a reactive thiocarbonylthio end group. A series of well‐defined star diblock [poly(ε‐caprolactone)‐b‐poly(N‐isopropylacrylamide)]₄ (SPCLNIP) copolymers were synthesized by R‐RAFT polymerization of N‐isopropylacrylamide (NIPAAm) using [PCL‐DDAT]₄ (SPCL‐DDAT) as a star macro‐RAFT agent (DDAT: S‐1‐dodecyl‐S′‐(α, α′‐dimethyl‐α″‐acetic acid) trithiocarbonate). The R‐RAFT polymerization showed a controlled/“living” character, proceeding with pseudo‐first‐order kinetics. All these star polymers with different molecular weights exhibited narrow molecular weight distributions of less than 1.2. The effect of polymerization temperature and molecular weight of the star macro‐RAFT agent on the polymerization kinetics of NIPAAm monomers was also addressed. Hardly any radical–radical coupling by‐products were detected, while linear side products were kept to a minimum by careful control over polymerization conditions. The trithiocarbonate groups were transferred to polymer chain ends by R‐RAFT polymerization, providing potential possibility of further modification by thiocarbonylthio chemistry. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Are o‐nitrobenzyl (meth)acrylate monomers polymerizable by controlled‐radical polymerization?

We report on the controlled‐radical polymerization of the photocleavable o‐nitrobenzyl methacrylate (NBMA) and o‐nitrobenzyl acrylate (NBA) monomers. Atom transfer radical polymerization (ATRP), reversible addition‐fragmentation chain transfer polymerization (RAFT), and nitroxide‐mediated polymerization (NMP) have been evaluated. For all methods used, the acrylate‐type monomer does not polymerize, or polymerizes very slowly in a noncontrolled manner. The methacrylate‐type monomer can be polymerized by RAFT with some degree of control (PDI ∼ 1.5) but leading to molar masses up to 11,000 g/mol only. ATRP proved to be the best method since a controlled‐polymerization was achieved when conversions are limited to 30%. In this case, polymers with molar masses up to 17,000 g/mol and polydispersity index as low as 1.13 have been obtained. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6504–6513, 2009     

Radical addition fragmentation chain transfer (RAFT) polymerization of ferrocenyl (Meth)acrylates

We report on the controlled free radical homopolymerization of 1‐ferrocenylethyl acrylate as well as of three new ferrocene bearing monomers, namely 4‐ferrocenylbutyl acrylate, 2‐ferrocenylamido‐2‐methylpropyl acrylate, and 4‐ferrocenylbutyl methacrylate, by the RAFT technique. For comparison, the latter monomer was polymerized using ATRP, too. The ferrocene containing monomers were found to be less reactive than their analogues free of ferrocene. The reasons for the low polymerizability are not entirely clear. As the addition of free ferrocene to the reaction mixture did not notably affect the polymerizations, sterical hindrance by the bulky ferrocene moiety fixed on the monomers seems to be the most probable explanation. Molar masses found for 1‐ferrocenylethyl acrylate did not exceed 10,000 g mol^?1, while for 4‐ferrocenylbutyl (meth)acrylate molar masses of 15,000 g mol^?1 could be obtained. With PDIs as low as 1.3 in RAFT polymerization of the monomers, good control over the polymerization was achieved. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation of miktoarm star‐block copolymers PSn‐b‐PVAc4‐n via combination of ATRP and RAFT polymerization

Three tetrafunctional bromoxanthate agents (Xanthate₃‐Br, Xanthate₂‐Br₂, and Xanthate‐Br₃) were synthesized. Initiative atom transfer radical polymerizations (ATRP) of styrene (St) or reversible addition fragmentation chain transfer (RAFT) polymerizations of vinyl acetate (VAc) proceeded in a controlled manner in the presence of Xanthate₃‐Br, Xanthate₂‐Br₂, or Xanthate‐Br₃, respectively. The miktoarm star‐block copolymers containing polystyrene (PS) and poly(vinyl acetate) (PVAc) chains, PS_n‐b‐PVAc_4‐n (n = 1, 2, and 3), with controlled structures were successfully prepared by successive RAFT and ATRP chain‐extension experiments using VAc and St as the second monomers, respectively. The architecture of the miktoarm star‐block copolymers PS_n‐b‐PVAc_4‐n (n = 1, 2, and 3) were characterized by gel permeation chromatography and ¹H NMR spectra. Furthermore, the results of the cleavage of PS₃‐b‐PVAc and PVAc₂‐b‐PS₂ confirmed the structures of the obtained miktoarm star‐block copolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Emulsion polymerization of vinyl acetate using iodine‐transfer and RAFT radical polymerizations

This study deals with control of the molecular weight and molecular weight distribution of poly(vinyl acetate) by iodine‐transfer radical polymerization and reversible addition‐fragmentation transfer (RAFT) emulsion polymerizations as the first example. Emulsion polymerization using ethyl iodoacetate as the chain transfer agent more closely approximated the theoretical molecular weights than did the free radical polymerization. Although ¹H NMR spectra indicated that the peaks of α‐ and ω‐terminal groups were observed, the molecular weight distributions show a relatively broad range (M_w/M_n = 2.2–4.0). On the other hand, RAFT polymerizations revealed that the dithiocarbamate 7 is an excellent candidate to control the polymer molecular weight (M_n = 9.1 × 10³, M_w/M_n = 1.48), more so than xanthate 1 (M_n = 10.0 × 10³, M_w/M_n = 1.89) under same condition, with accompanied stable emulsions produced. In the M_n versus conversion plot, M_n increased linearly as a function of conversion. We also performed seed‐emulsion polymerization using poly(nonamethylene L ‐tartrate) as the chiral polyester seed to fabricate emulsions with core‐shell structures. The control of polymer molecular weight and emulsion stability, as well as stereoregularity, is also discussed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

2‐Cyanoprop‐2‐yl dithiobenzoate mediated reversible addition–fragmentation chain transfer polymerization of acrylonitrile targeting a polymer with a higher molecular weight

The reversible addition–fragmentation chain transfer (RAFT) polymerization of acrylonitrile (AN) mediated by 2‐cyanoprop‐2‐yl dithiobenzoate was first applied to synthesize polyacrylonitrile (PAN) with a high molecular weight up to 32,800 and a polydispersity index as low as 1.29. The key to success was ascribed to the optimization of the experimental conditions to increase the fragmentation reaction efficiency of the intermediate radical. In accordance with the atom transfer radical polymerization of AN, ethylene carbonate was also a better solvent candidate for providing higher controlled/living RAFT polymerization behaviors than dimethylformamide and dimethyl sulfoxide. The various experimental parameters, including the temperature, the molar ratio of dithiobenzoate to the initiator, the molar ratio of the monomer to dithiobenzoate, the monomer concentration, and the addition of the comonomer, were varied to improve the control of the molecular weight and polydispersity index. The molecular weights of PANs were validated by gel permeation chromatography along with a universal calibration procedure and intrinsic viscosity measurements. ¹H NMR analysis confirmed the high chain‐end functionality of the resultant polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1272–1281, 2007     

SET‐RAFT of MMA mediated by ascorbic acid‐activated copper oxide

In this work, cupric oxide (CuO) or cuprous oxide (Cu₂O) was used as the catalyst for the single electron transfer‐reversible addition‐fragmentation chain transfer (SET‐RAFT) polymerization of methyl methacrylate in the presence of ascorbic acid at 25 °C. 2‐Cyanoprop‐2‐yl‐1‐dithionaphthalate (CPDN) was used as the RAFT agent. The polymerization occurred smoothly after an induction period arising from the slow activation of CuO (or Cu₂O) and the “initialization” process in RAFT polymerization. The polymerizations conveyed features of “living”/controlled radical polymerizations: linear evolution of number‐average molecular weight with monomer conversion, narrow molecular weight distribution, and high retention of chain end fidelity. From the polymerization profile, it was deduced that the polymerization proceeded via a conjunct mechanism of single electron transfer‐living radical polymerization (SET‐LRP) and RAFT polymerization, wherein CPDN acting as the initiator for SET‐LRP and chain transfer agent for RAFT polymerization. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Controlled polymerization of carbazole‐based vinyl and methacrylate monomers at ambient temperature: A comparative study through ATRP,SET, and SET‐RAFT polymerizations

The polymerization of N‐vinylcarbazole (NVK) and carbazole methacrylate (CMA) was carried out using controlled radical polymerization methods such as atom transfer radical polymerization (ATRP), single electron transfer (SET)‐LRP, and single electron transfer initiation followed by reversible addition fragmentation chain transfer (SET‐RAFT). Well‐controlled polymerization with narrow molecular weight distribution (M_w/M_n) < 1.25 was achieved in the case of NVK by high‐temperature ATRP while ambient temperature SET‐RAFT polymerization was relatively slow and controlled. In the case of CMA, SET‐RAFT is found to be more suitable for the ambient temperature polymerization. The polymerization rate followed first order kinetics with respect to monomer conversion and the molecular weight of the polymer increased linearly with conversion. The controlled nature of the polymerization is further demonstrated by the synthesis of diblock copolymers from PNVK and PCMA macroinitiators using a new flavanone‐based methacrylate (FMA) as the second monomer. All the polymers exhibited fluorescence. The excimer bands in the homopolymers of PNVK and PCMA were very broad, which may be attributed to the carbazole–carbazole overlap interaction. The scanning electron microscopy analysis of the block copolymer reveals interesting morphological features. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Reversible addition–fragmentation chain transfer polymerization of 2‐naphthyl acrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

The reversible addition–fragmentation chain transfer (RAFT) polymerizations of 2‐naphthyl acrylate (2NA) initiated by 2,2′‐azobisisobutyronitrile were investigated with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN) as a RAFT agent at various temperatures in a benzene solution. The results of the polymerizations showed that 2NA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion. The polydispersities of the polymer were relatively low up to high conversions in all cases. The chain‐extension reactions of poly(2‐naphthyl acrylate) (P2NA) with methyl methacrylate and styrene successfully yielded poly(2‐naphthyl acrylate)‐b‐poly(methyl methacrylate) and poly(2‐naphthyl acrylate)‐b‐polystyrene block polymers, respectively, with narrow polydispersities. The P2NA obtained by RAFT polymerization had a strong ultraviolet absorption at 270 nm, and the molecular weights had no apparent effect on the ultraviolet absorption intensities; however, the fluorescence intensity of P2NA increased as the molecular weight increased and was higher than that of 2NA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2632–2642, 2005     

Synthesis of methacrylate derivatives oligomers by dithiobenzoate‐RAFT‐mediated polymerization

Reversible addition fragmentation chain transfer (RAFT) was used to synthesize methacrylic acid oligomers and oligo(methacrylic acid)‐b‐poly(methyl methacrylate) (PMAA‐b‐PMMA) with targeted degree of polymerization ≈ 10. Characterization is by size‐exclusion chromatography (SEC) and electrospray mass‐spectrometry. SEC data are presented as hydrodynamic volume distributions (HVDs), the only proper means to present comparative and meaningful SEC data when there is no unique relationship between size and molecular weight. The RAFT agent, (4‐cyanopentanoic acid)‐4‐dithiobenzoate (CPADB), produced dithiobenzoic acid as a side product during the polymerization of methacrylate derivatives. Precipitation in diethyl ether proved to be an easy way to remove this impurity from the PMAA‐RAFT oligomers. Both unpurified and purified macro‐RAFT agent were used to prepare amphiphilic PMAA‐b‐PMMA copolymers. Diblock copolymer prepared from the purified PMAA homopolymer had a narrower HVD in comparison to those obtained from the equivalent unpurified macro‐RAFT agent. This work shows that while cyanoisopropyl‐dithiobenzoate or CPADB are good RAFT agents for methacrylate derivatives, they exhibit some instability under typical polymerization conditions, and thus when oligomers are targeted, optimal control requires checking for the degradation product and appropriate purification steps when necessary (the same effect is present for larger polymers but is unimportant). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2277–2289, 2008