Thermally stimulated depolarization current in electron‐irradiated poly(vinylidene fluoride‐trifluoroethylene) (56/44 mol %) copolymers

The effect of electron irradiation on poly(vinylidene fluoride‐trifluoroethylene) (56/44 mol %) copolymers was studied with dielectric constant measurements, differential scanning calorimetry (DSC), X‐ray diffraction, thermally stimulated depolarization current (TSDC) spectroscopy, and polarization hysteresis loops. The dielectric relaxation peaks, obeying the Vogel–Fulcher law, indicated that the copolymers were transformed from a normal ferroelectric to a relaxor ferroelectric. The X‐ray and DSC results showed that both the crystalline and polar ordering decreased after irradiation, indicating a partial recovery from trans–gauche bonds to local trans bonds (polar ordering). Moreover, the peak temperature decreased with the irradiation dose in the TSDC spectra; this demonstrated fewer dipoles and crystalline regions in the irradiated copolymer films during the ferroelectric–paraelectric transition and was consistent with polarization hysteresis loop measurements. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1099–1105, 2004     

Time‐resolved wide‐angle X‐ray scattering measurements during the isothermal crystallization and ferroelectric phase‐transition processes of a vinylidene fluoride/trifluoroethylene copolymer

The time‐resolved measurement of wide‐angle X‐ray scattering was performed with a synchrotron radiation source during the processes of the isothermal crystallization and ferroelectric phase transition of a vinylidene fluoride/trifluoroethylene copolymer with 73 mol % vinylidene fluoride. When the sample was cooled rapidly from the melt to the temperature region of the paraelectric high‐temperature phase, the peak position of the 200/110 reflection shifted toward the higher angle side and the half‐width became narrower. This indicated an increase in the crystallite size with a more compact chain‐packing mode. Even when the temperature jump was made from the melt into the region of the ferroelectric or low‐temperature phase, the crystallization of the high‐temperature phase was first observed before the appearance of the low‐temperature phase. This was consistent with a prediction based on the so‐called Ostwald state rule: the thermodynamically unstable but kinetically preferable high‐temperature phase can appear first even when the thermodynamically more stable low‐temperature phase should be created. The time‐dependent intensity changes were analyzed with the Avrami kinetic equation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4175–4181, 2004     

Dual photo‐ and thermally initiated cationic polymerization of epoxy monomers

Selective inhibition of the photoinitiated cationic ring‐opening polymerization of epoxides by dialkyl sulfides has provided dual systems that can be “activated” by UV irradiation and then subsequently be polymerized by the application of heat. It is proposed that dialkyl sulfides terminate the initial or growing polyether chains at an early stage to form stable trialkylsulfonium salts. These systems are dormant at room temperature but on thermolysis, the sulfonium salts are capable of reinitiating ring‐opening polymerization. These dual photo‐ and thermal cure systems have potential applications in adhesives, potting resins, and composites. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6750–6764, 2006     

Phase separation and polymer crystallization in a poly(4‐methyl‐1‐pentene)–dioctylsebacate–dimethylphthalate system via thermally induced phase separation

The effects of the polymer concentration and quenching temperature on the phase separation, the membrane morphology and polymer crystallization behavior in a poly(4‐methyl‐1‐pentene) (TPX)‐dioctylsebacate (DOS)‐dimethylphthalate (DMP) system via thermally induced phase separation were studied with a pseudobinary phase diagram, with the weight ratio of DOS:DMP = 1:1. SEM was used to observe the membrane morphology and structure, whereas the TPX crystallization behavior was studied with DSC and WAXD. Liquid‐liquid phase separation occurred, although quenching under the crystallization temperature. As the quenching temperature decreased, the pore size decreased, with better connected pore structure formed. The membranes quenched at 333 and 363 K showed good cellular structures, with an average pore size of about 2.3μm, whereas the pores of the membranes quenched at 393 and 423 K were not well formed, with some lamellar crystals on the inner side. The diluent assisted the mobility of the polymer chain, which improved the polymer crystallization. Dual‐melting‐peak behavior occurred for all the samples studied here. As the quenching temperature increased, the first peak of the melting trace moved to a higher temperature, whereas the second one stayed almost the same. The flexibility of the TPX main chain was restricted by the side groups, which allowed liquid‐liquid phase separation to occur first when quenched below the equilibrium crystallization temperature. This allowed primary and secondary crystallization, which was responsible for the dual‐melting‐peak behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 153–161, 2007     

Triblock copolymer synthesis via controlled radical polymerization in solution using S‐tert‐alkyl‐N,N‐alkoxycarbonylalkyldithiocarbamate RAFT agents

This paper presents the solution homopolymerization, random and block copolymerization of acrylic monomers, mediated using an S‐(1,4‐phenylenebis(propane‐2,2‐diyl)) bis(N,N‐butoxycarbonylmethyldithiocarbamate) RAFT agent. Fair to good control was obtained over the solution homopolymerization of various acrylic monomers. Although inhibition periods were observed, nearly no retardation was found to occur. Satisfactory control was also obtained over the solution copolymerization of n‐butyl acrylate with methacrylic acid, mediated using this RAFT agent. Finally, triblock copolymer synthesis, starting from the macromolecular intermediates produced in the homo‐ and copolymerization experiments, was studied, and was shown to be successful. The observed relatively broad molar mass distributions could be explained by a partial decomposition of the dithiocarbamate‐based RAFT agent during synthesis and/or polymerization, for which strong indications were obtained by performing a careful MALDI‐ToF MS analysis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6419–6434, 2006     

Dual roles of alkyl alcohols as syndiotactic‐specificity inducers and accelerators in the radical polymerization of N‐isopropylacrylamide and some properties of syndiotactic poly(N‐isopropylacrylamide)

The effects of simple alkyl alcohols on the radical polymerization of N‐isopropylacrylamide in toluene at low temperatures were investigated. We succeeded in the induction of syndiotactic specificity and the acceleration of polymerization reactions at the same time by adding simple alkyl alcohols such as 3‐methyl‐3‐pentanol (3Me3PenOH) to N‐isopropylacrylamide polymerizations. The dyad syndiotacticity increased with a decrease in the temperature and an increase in the bulkiness of the added alcohol and reached up to 71% at ?60 °C in the presence of 3Me3PenOH. With the assistance of NMR analysis, it was revealed that the alcohol compounds played dual roles in this polymerization system; an alcohol compound coordinating to the N? H proton induced syndiotactic specificity, and that hydrogen‐bonded to the C?O oxygen accelerated the polymerization reaction. The effect of syndiotacticity on the properties of poly(N‐isopropylacrylamide)s was also examined in some detail. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4450–4460, 2006     

Structural and phenomenological study on the cationic curing of mixtures of epoxy resin and 5,5‐dimethyl‐1,3‐dioxane‐2‐one

Ytterbium and lanthanum triflates were used as initiators to cure a mixture of diglycidylether of bisphenol A (DGEBA) and 5,5‐dimethyl‐1,3‐dioxane‐2‐one (DMTMC). The evolution of the curing was studied by differential scanning calorimetry (DSC) and Fourier transform infrared in the attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and to quantify the evolution of the groups involved in the curing process. We observed the formation of a five‐membered cyclic carbonate, which remains unreacted at the chain ends because of an equilibrium process between the spiroortho carbonates that had formed as intermediate species and also the loss of CO₂, which was quantified by thermogravimetry. The kinetics were studied by DSC and analyzed by isoconversional procedures. Thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA) experiments were used to evaluate the properties of the thermosets obtained. The phenomenological changes that take place during curing were studied and represented in a time‐temperature‐transformation (TTT) diagram. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4546–4558, 2006     

Polymorphism of nylon‐6 in multiwalled carbon nanotubes/nylon‐6 composites

The effects of pristine and amino‐functionalized multiwalled carbon nanotubes (MWNTs) on the crystallization behaviors of nylon‐6 were investigated by differential scanning calorimetry and X‐ray diffraction. The results indicate the presence of polymorphism in nylon‐6 and its composites, which is dependent on the MWNTs concentration and the cooling rate. More MWNTs and slow cooling from the melt favors the formation of α crystalline form. With the increase in cooling rates, the crystallinity of neat nylon‐6 decreases, and that of the composites decreases initially but increases afterward. Moreover, the degree of crystallinity of the composites is higher than neat nylon‐6 under high cooling rates, counter to what is observed under low cooling rates. The heterogeneous nucleation induced by MWNTs and the restricted mobility of polymer chains are considered as the main factors. Furthermore, addition of MWNTs increases the crystallization rate of α crystalline form but amino‐functionalization of MWNTs weakens this effect. The influence of thermal treatment on the crystalline structure of MWNTs/nylon‐6 composites is also discussed. A γ–α phase transition takes place at lower temperature for MWNTs/nylon‐6 composites than for nylon‐6. The annealing peaks of the composites annealed at 160 °C are higher than that of neat nylon‐6, and the highest annealing peak is obtained for amino‐functionalized MWNTs/nylon‐6 composites. This phenomenon is closely related to the different nucleation and recrystallization behaviors produced by various MWNTs in confined space. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1499–1512, 2006     

Influence of additives on the crystal structure and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate)

The influence of additives on the crystal modification and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) was investigated with wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). The addition of a nucleating promoter, Ceraflour 993, had no effect on the crystal modification and melting behavior of PEN crystallized under all chosen experimental conditions. However, the addition of a nucleating agent, sodium benzoate (SB), did affect the crystal modification and melting behavior of PEN when PEN/SB was crystallized at a higher temperature, but not at a lower temperature. A mixture of α and β modifications of PEN was obtained, and an overlapped dual melting peak was observed in DSC curves when PEN was crystallized at a higher temperature in the presence of SB, instead of a single crystal form and a single melting peak for the crystallization of pure PEN. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 296–301, 2004     

Enhanced dielectric response in P(VDF‐TrFE) based all‐organic nanocomposites

A nanocomposite with enhanced dielectric response is developed using poly(vinylidene fluoride‐trifluoroethylene) [P(VDF‐TrFE)] as matrix and Chemically modified high dielectric constant organic semiconductor—copper phthalocyanine oligomer (CuPc)—as filler. Transmission electron microscope (TEM)‐observed morphologies reveal that in the nanocomposite the average size of CuPc particles is about 25 nm [1/24 of that of CuPc in physical blend of P(VDF‐TrFE) and CuPc]. The hot‐press nanocomposite film with 15 wt % CuPc can realize a dielectric constant of 540 at 100 Hz. The enhanced dielectric response in the nanocomposite demonstrates the significance of the interface effect in raising the material responses far beyond that expected by simple mixing rules when there is a large dielectric contrast between the polymer matrix and the dielectric filler in the composite. It is also interesting to note that at high frequencies (such as 100 MHz) the nanocomposite has a dielectric constant of ～100 and this value is comparable to those of current materials used in microwave applications. At 105 °C that is near the ferroelectric‐to‐paraelectric phase transition temperature of the P(VDF‐TrFE) ferroelectric, a much higher dielectric constant (about 1200 at 100 Hz) is obtained. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 490–495, 2010     

Synthesis of poly(n‐hexyl isocyanate‐b‐N‐vinylpyrrolidone) block copolymers by the combination of anionic and nitroxide‐mediated radical polymerizations: Micellization properties in aqueous solutions

A combination of anionic and nitroxide‐mediated radical polymerizations (dual initiator) was employed for the synthesis of poly(n‐hexyl isocyanate‐b‐N‐vinylpyrrolidone) (PHIC‐b‐PNVP) block copolymers. The samples were characterized with a size exclusion chromatograph equipped with refractive‐index and light scattering detectors as well as ¹H NMR spectroscopy. Relatively good control over the molecular weights was achieved. However, rather broad molecular weight distributions were obtained. The micellar properties of the PHIC‐b‐PNVP block copolymers were studied in water, which is a selective solvent for the poly(N‐vinylpyrrolidone) blocks. Static and dynamic light scattering revealed the presence of equilibrium between the micelles and clusters. The clusters partially deaggregated with increasing temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5719–5728, 2006     

3D‐morphology reconstruction of nanoscale phase‐separation in polymer memory blends

In many organic electronic devices functionality is achieved by blending two or more materials, typically polymers or molecules, with distinctly different optical or electrical properties in a single film. The local scale morphology of such blends is vital for the device performance. Here, a simple approach to study the full 3D morphology of phase‐separated blends, taking advantage of the possibility to selectively dissolve the different components is introduced. This method is applied in combination with AFM to investigate a blend of a semiconducting and ferroelectric polymer typically used as active layer in organic ferroelectric resistive switches. It is found that the blend consists of a ferroelectric matrix with three types of embedded semiconductor domains and a thin wetting layer at the bottom electrode. Statistical analysis of the obtained images excludes the presence of a fourth type of domains. The criteria for the applicability of the presented technique are discussed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1231–1237     

Role of sodium dodecylbenzenesulfonate in 2,2,6,6‐tetramethy‐1‐piperidinyloxy‐mediated styrene miniemulsion polymerization

In studying 2,2,6,6‐tetramethy‐1‐piperidinyloxy (TEMPO)‐mediated styrene miniemulsions, we have observed that the surfactant sodium dodecylbenzenesulfonate (SDBS) not only provides colloidal stability but also influences the rate of polymerization. Increasing the SDBS concentration results in higher polymerization rates, although the molecular weight distribution and particle size distribution are not significantly impacted. We have also examined another common sulfonate surfactant, DOWFAX 8390. In contrast to SDBS, DOWFAX 8390 does not affect the polymerization rate. Furthermore, DOWFAX‐stabilized polymerizations are slower than SDBS‐stabilized polymerizations. TEMPO‐mediated bulk styrene polymerizations are also accelerated significantly in the presence of SDBS. Although the mechanism for the rate acceleration is unknown, the experimental evidence suggests that SDBS is participating in the generation of radicals capable of propagating, thereby reducing the TEMPO concentration within the particles. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5974–5986, 2006     

Doping of polyvinylidene difluoride with cobalt nitrate: Structural,electrical, and magnetic properties

Polyvinylidene difluoride (PVDF) doped with a few percentage of cobalt nitrate hexahydrate induces transition into the ferroelectric β‐phase. Infrared spectra show peaks indicative of β‐phase PVDF at 1277 cm^?1 and loss of the α‐phase peak at 790 cm^?1 while polarization measurements show loops consistent with relaxor ferroelectric behavior. Electronic spectroscopy shows that the Co²⁺ ion is in a six‐coordinate environment, and this is confirmed by magnetic susceptibility. Thermal measurements show that the PVDF melts near 155 °C, depending on the Co²⁺ content, and that there are several other thermal features that are associated with the hydrated cobalt nitrate. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Morphological changes during heating in poly(L‐lactic acid)/poly(butylene succinate) blend systems as studied by synchrotron X‐ray scattering

Blends of poly(L ‐lactic acid) (PLA) and poly(butylene succinate) (PBS) were prepared in various compositions via melt mixing, and the morphological changes were investigated with differential scanning calorimetry and synchrotron wide‐angle and small‐angle X‐ray scattering techniques at a heating rate of 10 °C/min. Differential scanning calorimetry thermograms of PLA/PBS blends showed two distinct melting peaks over the entire composition range. The exothermal peak for PLA shifted significantly to a lower temperature and overlapped with that of PBS around 100 °C. A depression of the melting point of the PLA component via blending was observed. The synchrotron wide‐angle X‐ray scattering during heating revealed that there was no cocrystallization or crystal modification via blending. The synchrotron small‐angle X‐ray scattering data showed that well‐defined double‐scattering peaks (or peaks with a clear scattering shoulder) appeared during crystallization, indicating that this system possessed dual lamellar stacks. These peaks were deconvoluted into two components with a peak separation computer program, and then the morphological parameters of each component were obtained by means of the correlation function. The long period and average lamellar thickness of the two components before melting decreased with an increasing content of the other polymer component. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1931–1939, 2002     

Electro‐optical behavior of ferroelectric liquid crystalline polyphenylene derivatives

Liquid crystalline (LC) polyphenylene derivatives, such as poly(para‐phenylene) (PPP), poly(meta‐phenylene) (PMP), poly(meta‐biphenylene) (PBP), and poly (meta‐terphenylene) (PTP) derivatives, were synthesized through substitution of fluorine‐containing chiral LC groups into side chains, with an aim to develop ferroelectric LC (FLC) conjugated polymers. All the polymers, except PTP, showed enantiotropic liquid crystallinities, where several types of mesophases were observed in both heating and cooling processes. Among them, PPP and PMP derivatives showed chiral smectic C (S_C*) phases responsible for ferroelectricity. In fact, they exhibited quick response to electric field, in spite of high viscosities inherent to polymers, giving rise to switching times of less than 1 s between two S_C states with reversely directed alignment. Hysteresis loops between the polarization and electric field were also observed for PPP and PMP. The spontaneous polarization (P_S) of PMP remained unchanged even after the electric field became zero, affording the residual polarization (P_R) whose value was the same as that of P_S. This indicates that PMP has a prospective memory function based on FLC nature. The present study is the first report for realizing a quick switching in macroscopic alignment using electric field and also for generating a potential memory function in π‐conjugated polymers. It is elucidated that unusual polymer main chains such as polyphenylenes can be used to prepare new ferroelectric polymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3591–3610, 2008     

Synthesis,characterization, and properties of new sequenced poly(ether amide)s based on 2‐(4‐aminophenyl)‐5‐aminobenzimidazole and 2‐(3‐aminophenyl)‐5‐aminobenzimidazole

A set of new aromatic poly(ether amide)s containing benzimidazole groups and ethylene oxide sequences of different lengths were synthesized and characterized. The new polymers were prepared from two benzimidazole diamines, 2‐(4‐aminophenyl)‐5‐aminobenzimidazole and 2‐(3‐aminophenyl)‐5‐aminobenzimidazole, and various oligo(ethylene oxide)dibenzoyl chlorides. They exhibited good solubility in polar aprotic solvents and glass‐transition temperatures in the range of 125–300 °C (the longer the ethylene oxide spacer was, the lower the glass‐transition temperature was). The new polyamides were essentially amorphous, as observed by X‐ray diffraction measurements and confirmed by differential scanning calorimetry measurements, by means of which no melting endotherm was observed in any case. The decomposition temperatures, as revealed by thermogravimetric analysis in nitrogen, were about 400 °C for all of them, regardless of the length of the ethylene oxide content or the phenylene ring orientation (meta or para) of the diamine moiety. The number of ethylene oxide linkages per repeat unit also determined the water uptake. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1414–1423, 2006     

Poling influence on the mechanical properties and molecular mobility of highly piezoelectric P(VDF‐TrFE) copolymer

The calorimetric, dielectric, and mechanical responses of highly piezoelectric 70/30 P(VDF‐TrFE) displaying homogenous d₃₃ of ?19 pC N^?1 are studied. This work aims at better understanding the influence of poling on the mechanical properties of this copolymer. To explain the one decade mechanical modulus drop observed across the Curie transition, a stiffening process of the amorphous phase due to the local electric fields in the ferroelectric crystals is proposed. In poled P(VDF‐TrFE), these fields are preferentially aligned resulting in a more stable and higher modulus below the Curie transition. This hypothesis accounts for the lower dielectric signals obtained with the poled sample. Through the Curie transition, the vanishing of these local electric fields, stemming from progressive disorientation and conversion of ferroelectric crystals to paraelectric ones, releases the constraints on the amorphous phase, leading to a storage modulus drop typical of a viscoelastic transition. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1414–1422     

Synthesis and characterization of cross‐shaped p–n diblock oligomers

The cross‐shaped p–n diblock oligomers based on oligothiophenes (OTs) and 1,3,4‐oxadiazole (OXD) were synthesized and investigated regarding optical properties, electrochemistry, quantum chemical calculations, and intramolecular energy transfer. Since only one emission peak is observed in PL spectra of the oligomers, it is evidenced that effective energy transfer from the OXD to OTs branch. The electrochemical experiments show that almost complete spatial separation of HOMO and LUMO with the thiophene number increasing. The theoretical calculations were carried out regarding which conformer is the lowest in energy, the torsion angle between thiophene/oxadiazole and the central benzene ring, and electron densities distributions of the oligomers. Based on all data, a model for intramolecular energy‐transfer process has been put forward to explain the optical properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1066–1073, 2007     

Novel temperature‐responsive water‐soluble copolymers based on 2‐hydroxyethylacrylate and vinyl butyl ether and their interactions with poly(carboxylic acids)

Novel water‐soluble amphiphilic copolymers have been synthesized by free radical copolymerization of 2‐hydroxyethylacrylate with vinyl butyl ether. In water these copolymers exhibit lower critical solution temperature, which depends on the content of hydrophobic vinyl butyl ether units. The interaction between these copolymers and poly(acrylic acid) or poly(methacrylic acid) in aqueous solutions results in formation of interpolymer complexes stabilized by hydrogen bonds and hydrophobic interactions. An increase in hydrophobicity of the copolymers leads to the enhancement of their complex formation ability with respect to poly(acrylic acid) and poly(methacrylic acid). Poly(methacrylic acid) forms stronger complexes with the copolymers when compared with poly(acrylic acid). The complexes exhibit dual sensitivity to pH‐ and temperature and this property may be easily adjusted regulating the strength of interaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 195–204, 2006