Synthesis and characterization of novel polyimides with bulky pendant groups

New dianhydrides containing t‐butyl and phenyl pendant groups have been synthesized and used as monomers, together with commercial diamines, to prepare novel polyimides. The influence of the chemical structure of the monomers on their reactivity has been studied by quantum semiempirical methods. The polyimides have been characterized by FTIR and by NMR in the case of soluble polymers. The presence of pendant groups and the method used to imidize polyimide precursors greatly affected polymer properties such as solubility, glass transition temperature, thermal stability, and mechanical properties. As a rule, the novel polyimides showed better solubility in organic solvents than the parent polyimides. Glass transition temperatures in the range 250–270°C and decomposition temperatures over 520°C were observed for the set of current polymers. Tensile strengths up to 135 MPa and mechanical moduli up to 3.0 GPa were measured on films of the current polyimides. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 805–814, 1999     

Synthesis and properties of novel sulfonated (co)polyimides bearing sulfonated aromatic pendant groups for PEFC applications

Novel sulfonated diamines bearing aromatic pendant groups, namely, 3,5‐diamino‐3′‐sulfo‐4′‐(4‐sulfophenoxy) benzophenone (DASSPB) and 3,5‐diamino‐3′‐sulfo‐4′‐(2,4‐disulfophenoxy) benzophenone (DASDSPB), were successfully synthesized. Novel side‐chain‐type sulfonated (co)polyimides (SPIs) were synthesized from these two diamines, 1,4,5,8‐naphthalene tetracarboxylic dianhydride (NTDA) and nonsulfonated diamines such as 4,4′‐bis(3‐aminophenoxy) phenyl sulfone (BAPPS). Tough and transparent membranes of SPIs with ion exchange capacity of 1.5–2.9 meq g^?1 were prepared. They showed good solubility and high thermal stability up to 300 °C. They showed isotropic membrane swelling in water, which was different from the main‐chain‐type and sulfoalkoxy‐based side‐chain‐type SPIs. The relative humidity (RH) and temperature dependence of proton conductivity were examined. At low RH, the novel SPI membranes showed much higher conductivity than the sulfoalkoxy‐based SPIs. They showed comparable or even higher proton conductivity than Nafion 112 in water at 60 °C (>0.10 S cm^?1). The membrane of NTDA‐DASDSPB/BAPPS (1/1)‐s displayed reasonably high proton conductivities of 0.05 and 0.30 S cm^?1 at 50 and 100% RH, respectively, at 120 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2862–2872, 2006     

Synthesis and properties of polyimide ionomers containing sulfoalkoxy and fluorenyl groups

A series of sulfopropylated and sulfobutylated polyimide copolymers containing fluorenyl groups, SPI‐4, were synthesized to investigate the effect of alkyl side chains on the properties (stability, mechanical strength, water uptake, and proton conductivity) of the polymimide electrolyte membranes. SPI‐4 showed much better hydrolytic stability (in 10% MeOH aq at 100 °C) than the main chain sulfonated polyimide, SPI‐1. Tough, flexible, and ductile membranes were obtained from these copolymers. At high relative humidity all the SPI‐4 membranes showed high mechanical properties (>34 MPa of the maximum stress) and proton conductivity (>0.1 Scm^?1). These properties are comparable to or even better than those of the perfluorosulfonic acid ionomer (Nafion 112). The new polyimide ionomers have proved to be a possible candidate as polymer electrolyte membrane for PEFCs and DMFCs. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4439–4445, 2005     

Synthesis and characterization of novel perfluorinated polyimides with 3D‐controlled structures for photonic applications

We have designed and synthesized novel perfluorinated polyimides with 3D controlled structure. At first, we successfully developed the new synthetic routes to diamines with pendant bulky perfluorinated aromatic units in a multi‐step synthetic procedure. Novel perfluorinated polyimides were prepared in a two‐step reaction in N‐methyl‐2‐pyrrolidinone (NMP) solution: The first step was for the synthesis of polyamic acids (PAAs) and the second reaction was for the imidization of PAA. The polymer yield was over 89% and the inherent viscosity of PAAs was in the range of 0.24–0.36 dL/g. The thin films were prepared by spin‐coating the PAA solution in NMP onto various substrates such as a Si wafer or a KBr pellet, dried at 80 °C and further cured at 230 °C. The resultant polyimides are thermally stable over 400 °C. The refractive index and birefringence of the resultant polyimides are 1.5858–1.6452 and 0.01–0.005, respectively. The refractive index of polyimide decreases with increasing the fluorine content. The copolymerization and the ether linkages into the backbone reduce the birefringence of polyimides. Surprisingly, the pendant ether linkage is not a crucial factor in reducing the polyimide birefringence. Their birefringence is comparatively very low, compared with that of previous polyimides. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1326–1342, 2006     

Synthesis and properties of ortho‐linked aromatic polyimides based on 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene

A bis(ether amine) containing the ortho‐substituted phenylene unit and pendant tert‐butyl group, 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene, was synthesized and used as a monomer to prepare polyimides with six commercial dianhydrides via a conventional two‐stage procedure. The intermediate poly(amic acid)s had inherent viscosities of 0.78–1.44 dL/g, and most of them could be thermally converted into transparent, flexible, and tough polyimide films. The inherent viscosities of the resulting polyimides were in the range of 0.46–0.87 dL/g. All polyimides were noncrystalline, and most of them showed excellent solubility in polar organic solvents. The glass‐transition temperatures of these polyimides were in the range of 222–259 °C in differential scanning calorimetry and 212–282 °C in thermomechanicl analysis. These polyimides showed no appreciable decomposition up to 500 °C in thermogravimetric analysis in air or nitrogen. A comparative study of the properties with the corresponding polyimides without pendant tert‐butyl groups derived from 1,2‐bis(4‐aminophenoxy)benzene is also presented. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1551–1559, 2000     

The effect of crosslinked networks with poly(ethylene glycol) on sulfonated polyimide for polymer electrolyte membrane fuel cell

To investigate the effect of crosslinking by a hydrophilic group on a sulfonated polyimide electrolyte membrane, sulfonated polyimide end‐capped with maleic anhydride was synthesized using 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl, 2,2′‐disulfonic acid, 2‐bis [4‐(4‐aminophenoxy)phenyl] hexafluropropane and maleic anhydride. The sulfonated polyimides end‐capped with maleic anhydride were self‐crosslinked or crosslinked with poly(ethylene glycol) diacrylate. A series of the crosslinked sulfonated polyimides having various ratios of sulfonated polyimide and poly(ethylene glycol) diacrylate were prepared and compared with uncrosslinked and self‐crosslinked sulfonated polyimides. The synthesized sulfonated polyimide films were characterized for FTIR spectrum, thermal stability, ion exchange capacity, water uptake, hydrolytic stability, morphological structure, and proton conductivity. The formation of sulfonated polyimide was confirmed in FTIR spectrum. Thermal stability was good for all the sulfonated polyimides that exhibited a three‐step degradation pattern. Ion exchange capacity was the same for both the uncrosslinked and the self‐crosslinked sulfonated polyimides (1.30 mEq/g). When the crosslinked sulfonated polyimides with poly(ethylene glycol) were compared, the ion exchange capacity was decreased as 1.27 > 1.25 > 1.23 mEq/g and water uptake was increased as 23.8 < 24.0 < 24.3% with the increase in poly(ethylene glycol) diacrylate content. All the crosslinked sulfonated polyimides with poly(ethylene glycol) diacrylate were stable for over 200 h at 80 °C in deionized water. Morphological structure and mean intermolecular distance were obtained by WAXD. Proton conductivities were measured at 30, 50, 70, and 90 °C. The proton conductivity of the crosslinked sulfonated polyimides with poly(ethylene glycol) diacrylate increased with the increase in poly(ethylene glycol) diacrylate content despite the fact that the ion exchange capacity was decreased. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1455–1464, 2005     

Crosslinked sulfonated polyimide networks as polymer electrolyte membranes in fuel cells

Sulfonated polyimides with tertiary nitrogen in the polymer backbone were synthesized with 1,4,5,8‐naphthalenetetracarboxylic dianhydride, 4,4′‐diaminobiphenyl 2,2′‐disulfonic acid, 2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane, and diaminoacrydine hemisulfate. They were crosslinked with a series of dibromo alkanes to improve the hydrolytic stability. The crosslinked sulfonated polyimide films were characterized for their thermal stability, ion‐exchange capacity (IEC), water uptake, hydrolytic stability, and proton conductivity. All the sulfonated polyimides had good thermal stability and exhibited a three‐step degradation pattern. With an increase in the alkyl chain length of the crosslinker, IEC decreased as 1.23 > 1.16 > 1.06 > 1.01, and the water uptake decreased as 7.29 > 6.70 > 6.55 > 5.63. The order of the proton conductivity of the crosslinked sulfonated polyimides at 90 °C was as follows: polyimide crosslinked with dibromo butane (0.070) > polyimide crosslinked with dibromo hexane (0.055) > polyimide crosslinked with dibromo decane (0.054). The crosslinked polyimides showed higher hydrolytic stability than the uncrosslinked polyimides. Between the crosslinked polyimides, the hydrolytic stability decreased with an increase in the alkyl chain length of the crosslinker. The crosslinked and uncrosslinked sulfonated polyimides exhibited almost the same proton conductivities. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2370–2379, 2005     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Synthesis and physical properties of N-substituted polyimides based on imidazole

AB-type monomers based on imidazole for the preparation of polyimides were synthesized by carrying out a substitution at the 1-position of 2-amino-4,5-dicyanoimidazole, followed by hydrolysis. Thus, pendant groups such as hexyl and 2,4-dinitrophenyl as an aliphatic long chain and an electron-withdrawing group, respectively, were introduced at the 1-position of the imidazole monomer. A solid-state polymerization was employed to prepare the poly(imidazoleimide)s in the form of a film from poly(imidazoleamic acid chloride)s by heating up to 180–200°C. The carbonyl stretching peaks of the imide ring appear at 1808 (sym) cm^?1 and 1756 (antisym) cm^?1. The effects of monomer structure on reactivity and the degree of imidization were investigated by comparing the viscosity of the resultant polymers and intensity of carbonyl peak at 1808 cm^?1. The difference in the hydrolysis rate between polyimides having short or long aliphatic pendant groups at the 1-position was observed using FT-IR. The inherent viscosity of the N-hexyl polyimide was 1.26 dL/g in N-methyl pyrrolidinone (NMP) and 0.22 dL/g in the case of N-2,4-dinitrophenyl poly(amic acid) in methanesulfonic acid at 30°C. The structural, physical, and material properties of the polyimides were characterized by infrared, nuclear magnetic resonance, luminescence, viscosimetric methods, differential scanning calorimetry, thermogravimetric analysis, optical microscopy, and wide angle x-ray scattering. Solution properties were also investigated by monitoring the viscosity as a function of time at 30°C. Luminescence spectroscopy of the poly(1-methyl imidazole imide) and poly(1-methyl imidazoleamic acid) films shows an emission band centered at 535 and 505 nm, respectively. Thermal properties are described comparing the weight loss and decomposition temperature as a function of the polymer structure and the degree of imidization. © 1993 John Wiley & Sons, Inc.     

Preparation and properties of molecular‐weight‐controlled polyimides derived from 1,4‐bis(4′‐amino‐2′‐trifluoromethylphenoxy)benzene and 4,4′‐oxydiphthalic anhydride

A series of molecular‐weight‐controlled fluorinated aromatic polyimides were synthesized through the polycondensation of a fluorinated aromatic diamine, 1,4‐bis(4′‐amino‐2′‐trifluoromethylphenoxy)benzene, with 4,4′‐oxydiphthalic anhydride in the presence of phthalic anhydride as the molecular‐weight‐controlling and end‐capping agent. Experimental results demonstrated that the resulting polyimides could melt at temperatures of 250–300 °C to give high flowing molten fluids, which were suitable for melt molding to give strong and flexible polyimide sheets. Moreover, the aromatic polyimides also showed good solubility both in polar aprotic solvents and in common solvents. Polyimide solutions with solid concentrations higher than 25 wt % could be prepared with relatively low viscosity and were stable in storage at the ambient temperature. High‐quality polyimide films could be prepared via the casting of the polyimide solutions onto glass plates, followed by baking at a relatively low temperature. The molten behaviors and organosolubility of the molecular‐weight‐controlled aromatic polyimides depended significantly on the polymer molecular weights. Both the melt‐molded polyimide sheets and the solution‐cast polymer films exhibited outstanding combined mechanical and thermal properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1997–2006, 2006     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Synthesis and properties of poly(amic acid)s and polyimides based on 2,2′,6,6′‐biphenyltetracarboxylic dianhydride

Poly(amic acid)s (PAAs) having the high solution stability and transmittance at 365 nm for photosensitive polyimides have been developed. PAAs with a twisted conformation in the main chains were prepared from 2,2′,6,6′‐biphenyltetracarboxylic dianhydride (2,2′,6,6′‐BPDA) and aromatic diamines. Imidization of PAAs was achieved by chemical treatment using trifluoroacetic anhydride. Among them, the PAA derived from 2,2′,6,6′‐BPDA and 4,4′‐(1,3‐phenylenedioxy)dianiline was converted to the polyimide by thermal treatment. The heating at 300 °C under nitrogen did not complete thermal imidization of PAAs having glass‐transition temperatures (T_g)s higher than 300 °C to the corresponding PIs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6385–6393, 2006     

The preparation of novel silica modified polyimide membranes: synthesis,characterization, and gas separation properties

In this study, new monomers having siloxane groups were synthesized as an intermediate for preparation of siloxane modified polyimide polymers. Then with these monomers, the synthesis of uncrosslinked and crosslinked polyimide–siloxane hybrid polymer membranes were achieved. The purposes of the preparation of modified polyimides were to modify the thermal and chemical stability, and mechanical strength of polyimides, and to improve the gas separation properties of polymers. The new diamine monomer having siloxane groups was prepared from 3,5‐diaminobenzoic acid (3,5‐DABA) and 3‐aminopropyltrimethoxysilane (3‐APTMS) in N‐methyl‐2‐pyrollidone (NMP) at 180°C. The modified polyimide membranes having different amount of siloxane groups were synthesized from pyromellitic dianhydride (PMDA), 4,4‐oxydianiline (ODA), and 3,5‐diaminobenzamido‐N‐propyltrimethoxy silane (DABA/PTMS) in NMP using a two‐step thermal imidization process. The synthesis of modified polyimide membranes were characterized by Fourier transform infrared spectroscopy (FTIR). The thermal analysis of the polyimides were carried out by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Water absorption and swelling experiments were also carried out for the investigation of structural properties of polymers. FTIR observations confirmed that the polyimide membranes with new diamine intermediate were successfully obtained. Thermal analysis showed that the uncrosslinked copolyimides exhibited two glass transition temperatures, indicating that they were separated microphases and it was found that all the modified copolyimides had showed higher glass transition temperature (T_g) than unmodified polyimides. The separation properties of the prepared polyimide membranes were also characterized by permeability for O₂ and N₂ gases and ideal selectivity values were calculated. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and properties of novel regioirregular polyimides from easily synthesized asymmetrical dichlorophthalimide monomers

New asymmetrical aromatic dichlorophthalimide monomers containing pendant groups (trifluoromethyl or methyl) were conveniently prepared from inexpensive and commercially available compounds. With these monomers, a new class of soluble polyimides with a regioirregular structure within the polymer backbone was obtained by the Ni(0)‐catalyzed polymerization method. The structures of the polymers were confirmed by various spectroscopic techniques. The polyimides displayed better solubility and higher thermal stability than the corresponding regular polyimides. In addition, fluorinated polyimides in this study had low dielectric constants ranging from 2.52 to 2.78, low moisture absorptions of less than 0.59%, and low thermal expansion coefficients between 10.6 and 19.7 ppm/°C. The oxygen permeability coefficients and permeability selectivity of oxygen to nitrogen of the films were in the ranges of 2.99–4.20 barrer and 5.55–7.50, respectively. We have demonstrated that the synthetic pathway for polyimides provides a successful approach to increasing the solubility and processability of polyimides without sacrificing their thermal stability. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3550–3561, 2007     

Phosphoric acid‐doped imidazolium ionomers with enhanced stability for anhydrous proton‐exchange membrane applications

Phosphoric acid‐doped crosslinked proton‐conducting membranes with high anhydrous proton conductivity, and good chemical stability in phosphoric acid were synthesized and characterized. The synthetic procedure of the acid‐doped composite membranes mainly involves the in situ crosslinking of polymerizable monomer oils (styrene and acrylonitrile) and vinylimidazole, and followed by the sulfonation of pendant imidazole groups with butanesultone, and further doped with phosphoric acid. The resultant phosphoric acid‐doped composite electrolyte membranes are flexible and show high thermal stability and high‐proton conductivity up to the order of 10^?2 S cm^?1 at 160 °C under anhydrous conditions. The phosphoric acid uptake, swelling degree, and proton conductivity of the composite membranes increase with the vinylimidazole content. The resultant composite membranes also show good oxidative stability in Fenton's reagent (at 70 °C), and quite good chemical stability in phosphoric acid (at 160 °C). The properties of the prepared electrolyte membranes indicate their promising prospects in anhydrous proton‐exchange membrane applications. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013 , 51, 1311–1317     

Synthesis and properties of cross‐linkable high molecular weight fluorinated copolyimides

A series of novel high molecular weight fluorinated co‐polyimides (Co‐PIs) containing styryl side chain based on 1,3‐bis(2‐trifluoromethyl‐4‐aminophenoxy)‐5‐(2,3,4,5‐tetrafluorophenoxy)benzene (6FTFPB) were successfully synthesized. The weight‐average molecular weights (M_ws) and polydispersities of the co‐polyimides were in the range 8.93–10.81 × 10⁴ and 1.33–1.82, respectively. The co‐polyimide film showed excellent solubility in organic solvents, high tensile properties (tensile strength exceeded 91 MPa), excellent optical transparency (cutoff wavelength at 332–339 nm and light transparencies above 89% at a wavelength of 550 nm), and high thermal stability (5% thermal weight‐loss temperature up to 510 °C). The casting and spinning films could be cross‐linked by thermal curing. The cured films show better combination property (including excellent resistance to solvents) than that of co‐polyimides. For instance, the glass transition temperature of Co‐PI‐1 (the molar weight ratio of 6FTFPB was 30%) increased from 217 to 271 °C, the tensile strength enhanced from 94 to 96 MPa, the 5% thermal weight‐loss temperature improved from 514 to 525 °C. Moreover, after cured, Co‐PI‐1 film also has a coefficient of thermal expansion (CTE) value of 60.3 ppm °C^?1, low root mean square surface roughness (R_q) at 4.130 nm and low dielectric constant of 2.60. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 349–359     

Synthesis of new aromatic polyimides with various side chains containing a biphenyl mesogen unit and their abilities to control liquid-crystal alignments on the rubbed surface

New poly(m-phenylene 4,4′-oxydiphthalimide)s containing various side chains, such as 6-(4-biphenylmethoxy)hexyloxy group and 6-(phenylphenoxy)hexyloxy isomers, were synthesized, giving thin films of a high quality. All the polyimides apparently were almost amorphous, but exhibited short-range ordering in some extent, depending on the side chains. By incorporating side chains, the thermal properties, including stability, thermal expansivity, and glass transition temperature, were generally degraded, whereas the optical and dielectric properties were improved. All the polyimides exhibited a good rubbing processability and excellent performance in the controlling of both the alignment and the pretilt of LC molecules in the LC cell. The pretilt angle of LC molecules was easily achieved in a wide-angle range of 8–27°, depending upon the rubbing density as well as the incorporated side chains. The pretilting of LC molecules was very sensitive to all the molecular parameters (namely, the flexibility of polymer chain backbone as well as the isomeric structure of biphenyl mesogen end group, spacer length, and spacer conformation in the side chain) in the polyimide, in addition to the rubbing process. In particular, the side chains, which are much shorter in length than the long alkyl side chains in the polyimides being used widely as LC alignment layers, were evident to involve effectively in the alignment of and the pretilt of LC molecules, which are highly desired in the LC display industry. This might mainly be attributed to a strong interaction between the biphenyl mesogen end group of the side chain and the LC molecule. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2909–2921, 1999     

Highly organosoluble and flexible polyimides with color lightness and transparency based on 2,2‐bis[4‐(2‐trifluoromethyl‐4‐aminophenoxy)‐3,5‐dimethylphenyl]propane

A new diamine containing isopropylidene, methyl substituted arylene ether, and trifluoromethyl groups, 2,2‐bis[4‐(2‐trifluoromethyl‐4‐aminophenoxy)‐3,5‐dimethylphenyl]propane (BTADP), was synthesized and used in preparation of a series of polyimides by direct polycondensation with various aromatic tetracarboxylic dianhydrides in N, N‐dimethylacetamide (DMAc). All polymers derived from diamine (BTADP) with trifluoromethyl substituents were highly organosoluble in the solvents, like N‐methyl‐2‐pyrrolidinone (NMP), N,N‐dimethylacetamide, N,N‐dimethylformamide (DMF), pyridine, chloroform, tetrahydrofuran (THF), dimethyl sulfoxide (DMSO), dichloromethane, cyclohexanone, and γ‐butyrolactone at room temperature or upon heating at 70 °C. Inherent viscosities of the polyimides were found to range between 0.58 and 0.97 dL·g^?1. These polyimides had glass transition temperatures between 256 and 307 °C, and their 10% mass loss temperatures ranged from 440 to 462 °C and 421 to 443 °C under nitrogen and air, respectively. These polyimides had low dielectric constants in the range of 2.84–3.09. All the polyimides could be cast into films from DMAc solutions and were thermally converted into color lightness, optically transparent, flexible, and tough polyimides. The polyimide films had a tensile strength in the range of 83–97 MPa and a tensile modulus in the range of 2.0–2.2 GPa. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5766–5774, 2004     

Preparation of aromatic polyimides highly soluble in conventional solvents

Several highly soluble polyimides were synthesized from various aromatic tetracarboxylic dianhydrides and an aromatic diamine containing tert‐butyl pendent groups [4,4′‐methylenebis(2‐tert‐butylaniline)]. All the polyimides showed excellent solubility in common solvents such as chloroform, tetrahydrofuran, and dioxane at room temperature. The number‐average molecular weight ranged from 3.6 × 10⁴ to 1.3 × 10⁵ according to gel permeation chromatography relative to a polystyrene standard, and the polydispersity index was between 1.9 and 2.5. The glass‐transition temperatures of the resulting polyimides ranged from 213 to 325 °C, as measured by differential scanning calorimetry, and little weight loss was observed up to 450 °C in N₂ by thermogravimetric analysis. These experimental data indicated that the tert‐butyl pendent groups reduced the interactions among polymer chains to improve their solubility in organic solvents without the loss of thermal stability. Transparent and flexible films of these polyimides were obtained via casting from solution. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 229–234, 2002     

Synthesis and positive‐imaging photosensitivity of soluble polyimides having pendant carboxyl groups

Polyimides having pendant carboxyl groups were prepared by a direct one‐pot polycondensation of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride (6FDA) with 3,5‐diaminobenzoic acid (DABz) and bis[4‐(3‐aminophenoxy)phenyl]sulfone (m‐BAPS) in the presence of a γ‐valerolactone/pyridine catalyst system using N‐methyl‐2‐pyrrolidone (NMP)/toluene mixture as a solvent at 180 °C. The obtained polyimides were soluble in dipolar aprotic solvents such as dimethylformamide, dimethyl sulfoxide, and NMP as well as in tetrahydrofuran and aqueous basic solution. The solubility of the polyimides was dependent on the diamine composition. Photosensitve polyimide (PSPI) systems composed of the polyimides and diazonaphthoquinone compound as a photosensitive material gave positive‐tone behavior by UV irradiation, followed by development with aqueous tetramethylammonium hydroxide (TMAH) solution. The scanning electron microscopic photograph of the resulting image showed 10‐μm line/space resolution with about 15 μm of film thickness. The PSPIs baked at 350 °C for a short time had excellent thermal resistance comparable to the original polyimides. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 934–946, 2001