Ring‐opening polymerization of 1,3‐benzoxazines by p‐toluenesulfonates as thermally latent initiators

p‐Toluenesulfonic acid (TsOH) and several alkyl p‐toluenesulfonates, that is, methyl p‐toluenesulfonate (TsOMe), cyclohexyl p‐toluenesulfonate (TsOCH), and neopentyl p‐toluenesulfonate (TsONP), were evaluated as initiators for the ring‐opening polymerization of benzoxazines. TsOH and TsOMe were highly efficient initiators that induced the polymerization at 60 and 80 °C, respectively. In contrast, TsOCH and TsONP did not initiate the polymerization below 100 °C, while they induced the polymerization at elevated temperatures, 120 and 150 °C, respectively. When TsOCH was used as an initiator, the corresponding polymerization rate was comparable to that observed for the polymerization with using TsOH as an initiator. These results suggested that neutral TsOCH and TsONP can be regarded as “thermally latent initiators,” which underwent the thermal dissociation at the elevated temperatures to generate the corresponding alkyl cations and/or TsOH as the initiators of the polymerization. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Anionic polymerization of 4‐phenyl‐1‐buten‐3‐yne derivatives bearing electron‐withdrawing groups

The anionic polymerization of derivatives of 4‐phenyl‐1‐buten‐3‐yne was carried out to investigate the effect of substituents on the polymerization behavior. The polymerization of 4‐(4‐fluorophenyl)‐1‐buten‐3‐yne and 4‐(2‐fluorophenyl)‐1‐buten‐3‐yne in tetrahydrofuran at −78 °C with n‐BuLi/sparteine as an initiator gave polymers consisting of 1,2‐ and 1,4‐polymerized units in quantitative yields with ratios of 80/20 and 88/12, respectively. The molecular weights of the polymers were controlled by the ratio of the monomers to n‐BuLi, and the distribution was relatively narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), supporting the living nature of the polymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1016–1023, 2001     

Synthesis and application as polymer electrolyte of hyperbranched polyether made by cationic ring‐opening polymerization of 3‐{2‐[2‐(2‐hydroxyethoxy)ethoxy]ethoxymethyl}‐3′‐methyl‐oxetane

A novel cyclic ether monomer 3‐{2‐[2‐(2‐hydroxyethoxy)ethoxy]ethoxy‐methyl}‐3′‐methyloxetane (HEMO) was prepared from the reaction of 3‐hydroxymethyl‐3′‐methyloxetane tosylate with triethylene glycol. The corresponding hyperbranched polyether (PHEMO) was synthesized using BF₃·Et₂O as initiator through cationic ring‐opening polymerization. The evidence from ¹H and ¹³C NMR analyses revealed that the hyperbranched structure is constructed by the competition between two chain propagation mechanisms, i.e. active chain end and activated monomer mechanism. The terminal structure of PHEMO with a cyclic fragment was definitely detected by MALDI‐TOF measurement. A DSC test implied that the resulting polyether has excellent segment motion performance potentially beneficial for the ion transport of polymer electrolytes. Moreover, a TGA assay showed that this hyperbranched polymer possesses high thermostability as compared to its liquid counterpart. The ion conductivity was measured to reach 5.6 × 10^?5 S/cm at room temperature and 6.3 × 10^?4 S/cm at 80 °C after doped with LiTFSI at a ratio of Li:O = 0.05, presenting the promise to meet the practical requirement of lithium ion batteries for polymer electrolytes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3650–3665, 2006     

Infrared thermographic analysis on copolymerization of spiroorthoester with oxetane

Infrared (IR) thermography was employed to monitor temperature changes during the copolymerization of a spiroorthoester monomer with an oxetane monomer initiated with a benzyl sulfonium salt. The temperature changes in the polymerizations decreased with the increase of the initial feed ratios of the spiroorthocarbonate monomer. For instance, the temperature in the copolymerization of the equimolar mixture of both of the monomers increased only ～1 °C, whereas that in the homopolymerization of the oxetane monomer increased more than 20 °C. This result indicates that the copolymerization employing spiroorthocarbonate monomers effectively suppress temperature increase, which are responsible to shrinkage during cooling. The suppression of polymerization shrinkage by spiroorthocarbonate was also confirmed by density measurement of the polymers using a gas pycnometer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1388–1393, 2007.     

Selectivity in anionic and cationic ring‐opening polymerizations of tetramethyl‐1‐(3′‐trifluoromethylphenyl)‐1‐phenylcyclotrisiloxane and tetramethyl‐1‐[3′,5′‐bis(trifluoromethyl)phenyl]‐1‐phenylcyclotrisiloxane

Anionic and cationic ring‐opening polymerizations of two novel cyclotrisiloxanes, tetramethyl‐1‐(3′‐trifluoromethylphenyl)‐1‐phenylcyclotrisiloxane ( I ) and tetramethyl‐1‐[3′,5′‐bis(trifluoromethyl)phenyl]‐1‐phenylcyclotrisiloxane ( II ), are reported. Anionic ring‐opening polymerization of I or II leads to copolymers with highly regular microstructures. Copolymers obtained by cationic polymerizations of I or II , initiated by triflic acid, have less regular microstructures characteristic of chemoselective polymerization processes. The composition and microstructure of copolymers have been characterized by ¹H and ²⁹Si‐NMR, the molecular weight distributions by GPC, and the thermal properties by DSC and TGA. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5235–5243, 2004     

Ring opening polymerization of epoxides with urea‐derivatives of 4‐aminopyridine as thermally latent anionic initiator

In this study, a series of urea‐derivatives of 4‐aminopyridine (4AP) were evaluated as thermally latent initiators for the anionic ring‐opening polymerization of diglycidyl ether of bisphenol A (DGEBA). The urea‐derivatives were synthesized by the reactions of 4AP with the corresponding iso(thio)cyanates (phenyl isocyanate, tert‐butyl isocyanate, methylene diphenyl diisocyanate, and phenyl isothiocyanate). The ability of the urea‐derivatives as latent initiators was investigated with differential scanning calorimetry (DSC): Upon heating formulations comprised of DGEBA and the urea‐derivatives in a heating rate at 10 °C/min, the resulting DSC profiles indicated exothermic peaks to confirm that DGEBA underwent the polymerization efficiently. The corresponding DSC‐peak top temperatures (T_{peak top}) was higher than that observed for the formulation comprised of DGEBA and pristine 4AP, to clarify that the urea are useful initiators with thermal latency. A possible mechanism for the initiation step involves the thermal dissociation of the urea into 4AP and the corresponding isocyanates. 4AP thus generated readily initiated the ring‐opening polymerization of epoxide. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2518–2522     

Behavior of 3‐vinylpyridine in nitroxide‐mediated radical polymerization: The influence of nitroxide concentration,solvent, and temperature

The influence of nitroxide concentration, solvent, and temperature on the nitroxide‐mediated radical polymerization of 3‐vinylpyridine (3VP) was examined. Long‐chain poly(3‐vinylpyridine)s with low polydispersities were synthesized. The initial 2,2,6,6‐tetramethylpiperidin‐1‐oxyl concentration had no influence on the kinetics of the polymerization but was responsible for the obtained molar weights. Compared with the polymerization of styrene, the polymerization of 3VP proved quite fast. The influence of temperature on the reaction rate was also demonstrated, and the polymerization could be controlled even at 110 °C. Some polymerizations were also performed in solution to test the influence of a solvent such as ethylene–glycol, whose effect on the polymerization of 3VP was dependent on temperature. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3067–3073, 2000     

Cationic addition polymerization of 1,4‐dioxene using gacl3 as lewis acid catalyst: Long‐lived species‐mediated polymerization

Effective cationic addition polymerization of 1,4‐dioxene, a six‐membered cyclic olefin with two oxygen atoms adjacent to the double bond, was performed using a simple metal halide catalyst system in dichloromethane. The polymerization was controlled when the reaction was conducted using GaCl₃ in conjunction with an isobutyl vinyl ether–HCl adduct as a cationogen at –78°C to give polymers with predetermined molecular weights and relatively narrow molecular weight distributions. The long‐lived properties of the propagating species were further confirmed by a monomer addition experiment and the analyses of the product polymers by ¹H NMR and MALDI–TOF–MS. Although highly clean propagation proceeded, the apparent rate constant changed during the controlled cationic polymerization of 1,4‐dioxene. The reason for the change was discussed based on polymerization results under various conditions. The obtained poly(1,4‐dioxene) exhibited a very high glass transition temperature (T_g) of 217°C and unique solubility. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Photo‐triggered redox frontal polymerization: A new tool for synthesizing thermally sensitive materials

A novel approach of photo‐triggered redox frontal polymerization (FP) by integrating photocaged superbase (QA‐DBU) with a peroxide initiator (dibenzoyl peroxide, BPO) is presented for the synthesis of thermally sensitive materials. Under photo‐irradiation at a localized region, the regenerated superbase can diffuse into unirradiated regions and effectively actuate redox FP in a diffusion‐controlled manner. Moreover, the redox FP can be conducted at a much lower front temperature with enhanced front velocity. Astonishingly, the front temperature can be well‐modulated by changing the concentration of latent superbase. The prepared thermally sensitive fluorescent polymer composites exhibit enhanced fluorescence emission intensity compared to that of conventional thermal FP. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4515–4521     

Polymerization of epoxide with hydroxylamides as thermally latent initiators

A new class of thermally latent initiators for the ring‐opening polymerization of epoxides has been developed. The latent initiators developed herein were the hydroxylamides 1a , 1b , and 1c , which were synthesized from phthalide, 3‐isochromanone, and cis‐cyclohexahydrophthalide, respectively, by their ring‐opening reactions with pyrrolidine. These hydroxylamides were designed so that their hydroxyl groups could attack the amide moiety intramolecularly upon heating, leading to ring closure and formation of the corresponding lactones while releasing pyrrolidine, the initiator for the anionic ring‐opening polymerization of an epoxide. The temperatures at which this thermal dissociation occurred were strongly dependent on the hydroxylamide molecular structure. When using the hydroxylamides as thermally latent initiators, the polymerizations of bisphenol‐A diglycidyl ether were investigated at various temperatures. This investigation clarified that the threshold temperature, that is, the temperature at which polymerization was initiated, increased in the order of 1a , 1b , and then 1c . © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2611–2617     

Role of sodium dodecylbenzenesulfonate in 2,2,6,6‐tetramethy‐1‐piperidinyloxy‐mediated styrene miniemulsion polymerization

In studying 2,2,6,6‐tetramethy‐1‐piperidinyloxy (TEMPO)‐mediated styrene miniemulsions, we have observed that the surfactant sodium dodecylbenzenesulfonate (SDBS) not only provides colloidal stability but also influences the rate of polymerization. Increasing the SDBS concentration results in higher polymerization rates, although the molecular weight distribution and particle size distribution are not significantly impacted. We have also examined another common sulfonate surfactant, DOWFAX 8390. In contrast to SDBS, DOWFAX 8390 does not affect the polymerization rate. Furthermore, DOWFAX‐stabilized polymerizations are slower than SDBS‐stabilized polymerizations. TEMPO‐mediated bulk styrene polymerizations are also accelerated significantly in the presence of SDBS. Although the mechanism for the rate acceleration is unknown, the experimental evidence suggests that SDBS is participating in the generation of radicals capable of propagating, thereby reducing the TEMPO concentration within the particles. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5974–5986, 2006     

Synthesis of an oligo(ethylene glycol)‐based third‐generation thermoresponsive dendronized polymer

An improved strategy to synthesize oligo(ethylene glycol)‐based secondary generation (G2) dendron is presented. The overall synthesis efficiency increased by 50% when comparing to the previous method, and the product purification by column chromatography becomes much easier. Based on this approach, the synthesis of the third‐generation (G3) dendrons and the corresponding methacrylate‐based G3 macromonomer becomes feasible. Because of the oil characteristics of this macromonomer, its polymerization was able to be conducted in bulk with AIBN as the initiator. The polymerization degree of the third‐generation dendronized polymer ( PG3 ) was found to be around 16 based on GPC measurement. The thermally induced dehydration processes of this polymer were monitored by temperature‐varied proton NMR spectroscopy, and its thermoresponsive behaviors were investigated with turbidity measurements using UV–vis spectroscopy. Similar to the lower generation counterparts, this threefold branched dendronized polymer also shows characteristic fast and sharp phase transitions around its apparent lower critical solution temperature. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6630–6640, 2009     

Side‐chain conformational changes during the thermoshrinking process: γ‐Ray polymerization and spectroscopic study of uncrosslinked poly(methacryloyl‐Ala‐OMe)

Poly(methacryloyl‐L ‐alanine‐methyl ester) (1) has an optically active side chain and consists of thermoshrinking hydrogels upon crosslinking. We synthesized an uncrosslinked polymer of 1 by the γ‐ray polymerization method. For the prepared polymer, variable‐temperature circular dichroism (CD) and ¹H NMR spectra were studied, and we found conformational changes in the optically active side chains during the thermally induced phase transition. Intense CD spectra reveal ordered conformation in the side chain of 1 below the phase transition temperature (∼28 °C). A well‐resolved ¹H NMR spectrum of 1 at 0 °C shows that the conformational angles in the polymer side chain are fixed at low‐energy minima. With increasing temperature, the frozen side chain starts rotating vigorously and takes an unordered orientation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2671–2677, 2000     

Microwave‐assisted ring‐opening polymerization of ϵ‐caprolactone

Ring‐opening polymerization of ?‐caprolactone was carried out smoothly and effectively with constant microwave powers of 170, 340, 510, and 680 W, respectively, with a microwave oven at a frequency of 2.45 GHz. The temperature of the polymerization ranged from 80 to 210 °C. Poly(?‐caprolactone) (PCL) with a weight‐average molar mass (M_w) of 124,000 g/mol and yield of 90% was obtained at 680 W for 30 min using 0.1% (mol/mol) stannous octanoate as a catalyst. When the polymerization was catalyzed by 1% (w/w) zinc powder, the M_w of PCL was 92,300 g/mol after the reaction mixture was irradiated at 680 W for 270 min. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1749–1755, 2002     

Preparation of novel poly(ethylene oxide‐co‐glycidol)‐graft‐poly(ε‐caprolactone) copolymers and inclusion complexation of the grafted chains with α‐cyclodextrin

A well‐defined comblike copolymer of poly(ethylene oxide‐co‐glycidol) [(poly(EO‐co‐Gly)] as the main chain and poly(ε‐caprolactone) (PCL) as the side chain was successfully prepared by the combination of anionic polymerization and ring‐opening polymerization. The glycidol was protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether (EPEE) first, and then ethylene oxide was copolymerized with EPEE by an anionic mechanism. The EPEE segments of the copolymer were deprotected by formic acid, and the glycidol segments of the copolymers were recovered after saponification. Poly(EO‐co‐Gly) with multihydroxyls was used further to initiate the ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate. When the grafted copolymer was mixed with α‐cyclodextrin, crystalline inclusion complexes (ICs) were formed, and the intermediate and final products, poly(ethylene oxide‐co‐glycidol)‐graft‐poly(ε‐caprolactone) and ICs, were characterized with gel permeation chromatography, NMR, differential scanning calorimetry, X‐ray diffraction, and thermogravimetric analysis in detail. The obtained ICs had a channel‐type crystalline structure, and the ratio of ε‐caprolactone units to α‐cyclodextrin for the ICs was higher than 1:1. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3684–3691, 2006     

Self‐assembly of star‐shaped polystyrene‐block‐polypeptide copolymers synthesized by the combination of atom transfer radical polymerization and ring‐opening living polymerization of α‐amino acid‐N‐carboxyanhydrides

The self‐assembling nature and phase‐transition behavior of a novel class of triarm, star‐shaped polymer–peptide block copolymers synthesized by the combination of atom transfer radical polymerization and living ring‐opening polymerization of α‐amino acid‐N‐carboxyanhydride are demonstrated. The two‐step synthesis strategy adopted here allows incorporating polypeptides into the usual synthetic polymers via an amido–amidate nickelacycle intermediate, which is used as the macroinitiator for the growth of poly(γ‐benzyl‐L ‐glutamate). The characterization data are reported from analyses using gel permeation chromatography and infrared, ¹H NMR, and ¹³C NMR spectroscopy. This synthetic scheme grants a facile way to prepare a wide range of polymer–peptide architectures with perfect microstructure control, preventing the formation of homopolypeptide contaminants. Studies regarding the supramolecular organization and phase‐transition behavior of this class of polymer‐block‐polypeptide copolymers have been accomplished with X‐ray diffraction, infrared spectroscopy, and thermal analyses. The conformational change of the peptide segment in the block copolymer has been investigated with variable‐temperature infrared spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2774–2783, 2006     

Preparation and characterization of chitosan‐graft‐poly (ϵ‐caprolactone) with an organic catalyst

Chitosan‐graft‐poly(ϵ‐caprolactone) was prepared via the ring‐opening graft polymerization of ϵ‐caprolactone (CL) through chitosan with 4‐dimethylaminopyridine as a catalyst and water as a swelling agent. The graft content of PCL within the graft copolymer was adjusted by the feed ratio of CL to chitosan, and the highest grafting concentration of PCL was up to about 400%. Fourier transform infrared, ¹H NMR, and two‐dimensional heteronuclear single quantum coherence analyses indicated that the amino group (NH₂ CH‐2) of chitosan initiated the graft polymerization of CL through the backbone of chitosan, and the hydroxyl group (HO CH_2–6) of chitosan did not participate in initiating the graft polymerization. The percentage of amino groups initiating the graft polymerization decreased with an increasing molar ratio of CL to chitosan in the feed, and this was attributed to the fact that the graft polymerization system increasingly became heterogeneous with an increasing feed ratio of CL to chitosan. The physical properties of the graft copolymers were characterized by thermogravimetric analysis and wide‐angle X‐ray diffraction, respectively. These suggested that the introduction of PCL grafts through the chitosan backbone would to some extent destroy the crystalline structure of chitosan, and the PCL grafts existed in an amorphous structure. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5353–5361, 2006     

Ring‐opening polymerization of ε‐caprolactone via the bismuth‐2‐mercaptoethanol complex

A complex consisting of one Bi³⁺ ion and two 2‐mercaptoethanol units (BiME₂) was used as initiator for the ring‐opening polymerization of ε‐caprolactone in bulk. A kinetic comparison showed that BiME₂ is as reactive as initiator as Sn‐octanoate and more reactive than Bi‐hexanoate. The difference to BiHex₃ decreased at higher temperatures and upon addition of an alcohol as coinitiator. When tetra(ethylene glycol) was used as coinitiator, it was completely incorporated into the poly(εCL) chain, so that telechelic polylactones having two OH‐endgroups were formed. In the absence of a coinitiator, 2‐mercaptoethanol or its disulfide were incorporated in the form of ester groups. Furthermore, it was found by MALDI‐TOF mass spectrometry that small amounts of cyclic oligolactones (detected up to a degree of polymerization of 17) were formed under all reaction conditions. Higher temperatures and longer times favored a higher content of cycles. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3175–3183, 2006     

Deactivation reactions in the modeled 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐mediated free‐radical polymerization of styrene: A comparative study with the 2,2,6,6‐tetramethyl‐1‐piperidinyloxy/acrylonitrile system

The competitiveness of the combination and disproportionation reactions between a 1‐phenylpropyl radical, standing for a growing polystyryl macroradical, and a 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO) radical in the nitroxide‐mediated free‐radical polymerization of styrene was quantitatively evaluated by the study of the transition geometry and the potential energy profiles for the competing reactions with the use of quantum‐mechanical calculations at the density functional theory (DFT) UB3‐LYP/6‐311+G(3df, 2p)//(unrestricted) Austin Model 1 level of theory. The search for transition geometries resulted in six and two transition structures for the radical combination and disproportionation reactions, respectively. The former transition structures, mainly differing in the out‐of‐plane angle of the N? O bond in the transition structure TEMPO molecule, were correlated with the activation energy, which was determined to be in the range of 8.4–19.4 kcal mol^?1 from a single‐point calculation at the DFT UB3‐LYP/6‐311+G(3df, 2p)//unrestricted Austin Model 1 level. The calculated activation energy for the disproportionation reaction was less favorable by a value of more than 30 kcal mol^?1 in comparison with that for the combination reaction. The approximate barrier difference for the TEMPO addition and disproportionation reaction was slightly smaller for the styrene polymerization system than for the acrylonitrile polymerization system, thus indicating that a β‐proton abstraction through a TEMPO radical from the polymer backbone could diminish control over the radical polymerization of styrene with the nitroxide even more than in the latter system. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 232–241, 2007     

Synthesis and chemical modification of hyperbranched polyethers with terminal hydroxy groups by the anionic ring‐opening polymerization of 3‐alkyl‐3‐hydroxymethyl oxetanes

The anionic ring‐opening polymerization of oxetanes containing hydroxyl groups was carried out with potassium tert‐butoxide as an initiator in the presence of 18‐crown‐6‐ether in N‐methylpyrrolidinone at 180 °C; it yielded corresponding multifunctional hyperbranched polymers: poly(3‐ethyl‐3‐hydroxymethyloxetane)s, with number‐average molecular weights of 2200–4100 in 83–95% yields, and poly(3‐methyl‐3‐hydroxymethyloxetane)s, with number‐average molecular weights of 4600–5200 in 70–95% yields. The synthesized poly(3‐ethyl‐3‐hydroxymethyloxetane)s and poly(3‐methyl‐3‐hydroxymethyloxetane)s were hyperbranched polyethers containing an oxetane moiety and many hydroxy groups at the ends. The postpolymerization of poly(3‐ethyl‐3‐hydroxymethyloxetane)s was performed in the presence of potassium tert‐butoxide and 18‐crown‐6‐ether in N‐methylpyrrolidinone at 180 °C; it yielded corresponding polymers with higher molecular weights in good yields. The cationic polymerization of poly(3‐ethyl‐3‐hydroxymethyloxetane) derivatives was carried out with boron trifluoride etherate as an initiator and was followed by alkaline hydrolysis; this yielded a new branched polymer, a poly(hyperbranched polyether), with many pendant hydroxy groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3739–3750, 2004