Air‐stable and recoverable catalyst for copper‐catalyzed controlled/living radical polymerization of styrene; In situ generation of Cu(I) species via electron transfer reaction

Copper‐catalyzed controlled/living radical polymerization (LRP) of styrene (St) was conducted using the silica gel‐supported CuCl₂/N,N,N′,N′,N″‐pentamethyldiethylenetriamine (SG‐CuCl₂/PMDETA) complex as catalyst at 110 °C in the presence of a definite amount of air. This novel approach is based on in situ generation and regeneration of Cu(I) via electron transfer reaction between phenols and Cu(II). Sodium phenoxide or p‐methoxyphenol was used as a reducing agent of Cu(II) complexes in LRP. The number–average molecular weight, M_n,GPC, increases linearly with monomer conversion and agrees well with the theoretical values up to 85% conversion The molecular weight distribution, M_w/M_n, decreases as the conversion increases and reaches values below 1.2. The catalyst was recovered in aerobic condition and reused in copper‐catalyzed LRP of St. For the second run, the number–average molecular weights increased with monomer conversion and the polydispersities decreased as the polymerization proceeded and reached to the value <1.3 at 81% conversion. The recycled catalyst retained 90% of its original activity in the subsequent polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 77–87, 2006     

Synthesis of well‐defined naphthalene and photo‐labile group‐labeled polystyrene via ATRP

The atom transfer radical polymerizations of styrene were successfully carried out in bulk and solution, respectively, at 115 °C, with a novel photoiniferter reagent, (1‐naphthyl)methyl N,N‐diethyldithiocarbamate (NMDC), as an initiator in the presence of copper (I) bromide and N,N,N′,N″,N″‐pentamethyldiethylenetriamine. The results showed that NMDC was an effective initiator with high initiation efficiency for ATRP of St. The polymerization rate was first‐order with respect to the monomer concentration and the molecular weights of the obtained polystyrene (PS) increased linearly with the monomer conversion, with very narrow molecular weight distributions (M_w/M_n = 1.07–1.29). The functionalized naphthalene‐labeled PS bearing N,N‐(diethylamino)dithiocarbamoyl group which was confirmed by ¹H NMR analysis, and chain extension of the PS exhibited fluorescence and ultraviolet absorption in chloroform (CHCl₃). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 510–518, 2006     

Copper(0)‐mediated living radical polymerization of acrylonitrile at room temperature

The copper(0)‐catalyzed living radical polymerization of acrylonitrile (AN) was investigated using ethyl 2‐bromoisobutyrate as an initiator and 2,2′‐bipyridine as a ligand. The polymerization proceeded smoothly in dimethyl sulphoxide with higher than 90% conversion in 13 h at 25 °C. The polymerization kept the features of controlled radical polymerization. ¹H NMR spectra proved that the resultant polymer was end‐capped by ethyl 2‐bromoisobutyrate species. Such polymerization technique was also successfully introduced to conduct the copolymerization of styrene (St) and AN to obtain well‐controlled copolymers of St and AN at 25 °C, in which the monomer conversion of St could reach to higher than 90%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

The application of copper(II) deactivator on the single‐electron transfer living radical polymerization of tert‐butyl acrylate

We demonstrate the living radical polymerization of tert‐butyl acrylate (tBA) applying the SET mechanism, employing methyl 2‐bromopropionate (MBP) as initiator in dimethyl sulfoxide (DMSO) at ambient temperature. It is observed that introducing copper bromide into the catalyst system is necessary for controlling on the SET‐LRP polymerization of tBA. In this work, we make major investigation for the effect of the different stoichiometry quantity of copper bromide on the polymerization. Experiments show that the polymerization achieves better control with increasing the stoichiometry quantity of copper(II) deactivator. The structural analysis of the resulting polymers by ¹H NMR demonstrates the successful synthesis of poly(tBA)s by SET‐LRP in DMSO. Moreover, this work is helpful to the SET‐LRP of other monomers and is expected to expand the application of SET‐LRP. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2793–2797, 2010     

Quantification of ATRP initiator density on polymer latex particles by fluorescence labeling technique using copper‐catalyzed azide‐alkyne cycloaddition

We developed a novel fluorescence labeling technique for quantification of surface densities of atom transfer radical polymerization (ATRP) initiators on polymer particles. The cationic P(St‐CPEM‐C₄DMAEMA) and anionic P(St‐CPEM) polymer latex particles carrying ATRP‐initiating chlorine groups were prepared by emulsifier‐free emulsion polymerization of styrene (St), 2‐(2‐chloropropionyloxy)ethyl methacrylate (CPEM), and N‐n‐butyl‐N,N‐dimethyl‐N‐(2‐methacryloyloxy)ethylammonium bromide (C₄DMAEMA). ATRP initiators on the surface of polymer particles were converted into azide groups by sodium azide, followed by fluorescent labeling with 5‐(N,N‐dimethylamino)‐N′‐(prop‐2‐yn‐1‐yl)naphthalene‐1‐sulfonamide (Dansyl‐alkyne) by copper‐catalyzed azide‐alkyne cycloaddition (CuAAC). The reaction time required for both azidation of ATRP‐initiating groups and successive fluorescence labeling of azide groups with Dansyl‐alkyne by CuAAC were investigated in detail by FTIR and fluorescence spectral measurement, respectively. The ATRP initiator densities on the cationic P(St‐CPEM‐C₄DMAEMA) and anionic P(St‐CPEM) particle surfaces were estimated to be 0.21 and 0.15 molecules nm^?2, respectively, which gave close agreement with values previously determined by a conductometric titration method. The fluorescence labeling through click chemistry proposed herein is a versatile technique to quantify the surface ATRP initiator density both on anionic and cationic polymer particles. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4042–4051     

Synthesis of graft copolymer by ATRP of MMA from poly(phenylacetylene)

The present report describes the synthesis of a densely grafted copolymer consisting of a rigid main chain and flexible side chains by the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) from an ATRP initiator‐bearing poly(phenylacetylene) [poly(BrPA)]. Poly(BrPA) was obtained by the polymerization of 4‐ethynylbenzyl‐2‐bromoisobutyrate using [Rh(NBD)Cl]₂ in the presence of Et₃N. The ¹H NMR spectrum showed that poly(BrPA) was in the cis‐transoid form. Upon heating at 30 °C for 24 h the cis‐transoid form was maintained. ATRP of MMA from the poly(BrPA) was carried out at 30 °C using CuX (X = Br, Cl) as the catalyst and N,N,N′,N′,N′‐pentamethyldiethylenetriamine as the ligand, and the resulting graft copolymers were investigated with ¹H NMR and SEC. To analyze the graft structure in more detail, the graft copolymers were hydrolyzed with KOH and the resultant poly(MMA) part was investigated with ¹H NMR and SEC. The polydispersity indexes of 1.25–1.45 indicated that the graft copolymers have well‐controlled side chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6697–6707, 2006     

Copolymerization of methacrylic acid with methyl methacrylate by SET‐LRP

Single‐electron transfer living radical polymerization (SET‐LRP) has developed as a reliable, robust and straight forward method for the construction well‐defined polymers. To span an even larger variety of functional monomers, we investigated the copolymerization of methyl methacrylate with methacrylic acid by SET‐LRP. Copolymerizations were catalyzed by Cu(0)/Me₆‐TREN and performed in MeOH/H₂O mixtures at 50 °C. The SET‐LRP copolymerizations of varying methacrylic acid content were evaluated by kinetic experiments. At low (2.5%) and moderate (10%) MAA loadings, the copolymerizations obeyed perfect first order kinetics (k_p^app = 0.008 min^?1 and k_p^app = 0.006 min^?1) and exhibited a linear increase in molecular weights with conversion providing narrow molecular weight distributions. The SET‐LRP of MMA/25%‐MAA was found to be significantly slower (k_p^app = 0.0035 min^?1). However, a reasonable first‐order kinetics in monomer consumption was maintained, and the control of the polymerization process was preserved since the molecular weight increased linearly with conversion and could therefore be adjusted. This work demonstrates that the copolymerization of methacrylic acid by SET‐LRP is feasible and the design of well‐defined macromolecules comprising acidic functionality can be achieved. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Ultrafast SET‐LRP of methyl acrylate at 25 °C in alcohols

Alcohols are known to promote the disproportionation of Cu(I)X species into nascent Cu(0) and Cu(II)X. Therefore, alcohols are expected to be excellent solvents that facilitate the single‐electron transfer mediated living radical polymerization (SET‐LRP) mediated by nascent Cu(0) species. This publication demonstrates the ultrafast SET‐LRP of methyl acrylate initiated with bis(2‐bromopropionyloxy)ethane and catalyzed by Cu(0)/Me₆‐TREN in methanol, ethanol, 1‐propanol, and tert‐butanol and in their mixture with water at 25 °C. The structural analysis of the resulting polymers by a combination of ¹H NMR and MALDI‐TOF MS demonstrates the synthesis of perfectly bifunctional α,ω‐dibromo poly(methyl acrylate)s by SET‐LRP in alcohols. Moreover, this work provides an expansion of the list of solvents available for SET‐LRP. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2745–2754, 2008     

A density functional theory computational study of the role of ligand on the stability of CuI and CuII species associated with ATRP and SET‐LRP

Atom transfer radical polymerization (ATRP) and single electron‐transfer living radical polymerization (SET‐LRP) both utilize copper complexes of various oxidation states with N‐ligands to perform their respective activation and deactivation steps. Herein, we utilize DFT (B3YLP) methods to determine the preferred ligand‐binding geometries for Cu/N‐ligand complexes related to ATRP and SET‐LRP. We find that those ligands capable of achieving tetrahedral complexes with Cu^I and trigonal bipyramidal with axial halide complexes with [Cu^IIX]⁺ have higher energies of stabilization. We were able to correlate calculated preferential stabilization of [Cu^IIX]⁺ with those ligands that perform best in SET‐LRP. A crude calculation of energy of disproportionation revealed that the same preferential binding of [Cu^IIX]⁺ results in increased propensity for disproportionation. Finally, by examining the relative energies of the basic steps of ATRP and SET‐LRP, we were able to rationalize the transition from the ATRP mechanism to the SET‐LRP mechanism as we transition from typical nonpolar ATRP solvents to polar SET‐LRP solvents. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4950–4964, 2007     

Synthesis of poly(vinyl acetate)‐graft‐polystyrene by a combination of cobalt‐mediated radical polymerization and atom transfer radical polymerization

Vinyl acetate and vinyl chloroacetate were copolymerized in the presence of a bis(trifluoro‐2,4‐pentanedionato)cobalt(II) complex and 2,2′‐azobis(4‐methoxy‐2,4‐dimethylvaleronitrile) at 30 °C, forming a cobalt‐capped poly(vinyl acetate‐co‐vinyl chloroacetate). The addition of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy after a certain degree of copolymerization was reached afforded 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐terminated poly(vinyl acetate‐co‐vinyl chloroacetate) (PVOAc–MI; number‐average molecular weight = 31,000, weight‐average molecular weight/number‐average molecular weight = 1.24). A ¹H NMR study of the resulting PVOAc–MI revealed quantitative terminal 2,2,6,6‐tetramethyl‐1‐piperidinyloxy functionality and the presence of 5.5 mol % vinyl chloroacetate in the copolymer. The atom transfer radical polymerization (ATRP) of styrene (St) was studied with ethyl chloroacetate as a model initiator and five different Cu‐based catalysts. Catalysts with bis(2‐pyridylmethyl)octadecylamine (BPMODA) or tris(2‐pyridylmethyl)amine (TPMA) ligands provided the highest initiation efficiency and best control over the polymerization of St. The grafting‐from ATRP of St from PVOAc–MI catalyzed by copper complexes with BPMODA or TPMA ligands provided poly(vinyl acetate)‐graft‐polystyrene copolymers with relatively high polydispersity (>1.5) because of intermolecular coupling between growing polystyrene (PSt) grafts. After the hydrolysis of the graft copolymers, the cleaved PSt side chains had a monomodal molecular weight distribution with some tailing toward the lower number‐average molecular weight region because of termination. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 447–459, 2007     

Atom transfer radical polymerization of styrene using the novel initiator ethyl 2‐N,N‐(diethylamino)dithiocarbamoyl‐butyrate

The atom transfer radical polymerizations (ATRPs) of styrene initiated by a novel initiator, ethyl 2‐N,N‐(diethylamino)dithiocarbamoyl‐butyrate (EDDCB), in both bulk and solution were successfully carried out in the presence of copper(I) bromide (CuBr) and N,N,N′,N″,N″‐pentamethyldiethylenetriamine at 115 °C. The polymerization rate was first‐order with respect to the monomer concentration, and the molecular weights of the obtained polymers increased linearly with the monomer conversions with very narrow molecular weight distributions (as low as 1.17) up to higher conversions in both bulk and solution. The polymerization rate was influenced by various solvents in different degrees in the order of cyclohexanone > dimethylformamide > toluene. The molecular weight distributions of the produced polymers in cyclohexanone were higher than those in dimethylformamide and toluene. The results of ¹H NMR analysis and chain extension confirmed that well‐defined polystyrene bearing a photo‐labile N,N‐(diethylamino)dithiocarbamoyl group was obtained via ATRP of styrene with EDDCB as an initiator. The polymerization mechanism for this novel initiation system is a common ATRP process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 32–41, 2006     

Synthesis and polymerization of 5‐(N,N‐dimethylamino)naphthylacetylene with homogeneous rhodium and palladium complexes

The monomer 5‐ethynyl‐N,N‐dimethylnaphthalen‐1‐amine ( 2 ) was satisfactorily obtained by a heterocoupling reaction between 5‐iodo‐(N,N‐dimethyl)naphthalen‐1‐amine and 2‐methyl‐3‐butyn‐2‐ol catalyzed by a palladium–copper system and followed by acetone elimination. Poly(5‐ethynyl‐N,N‐dimethylnaphthalen‐1‐amine) was isolated by the reaction of 2 in the presence of homogeneous rhodium and palladium complexes. On the basis of the spectroscopic data, the polymer always showed a cis–transoidal, stereoregular structure. Moreover, only with the rhodium catalyst in methanol was a dimeric product isolated in a very low yield, having a conjugated terminal ene–yne structure, which permitted the consideration of a metallated chain‐transfer intermediate in the polymer propagation. The kinetics of the catalyzed reaction were analyzed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 437–446, 2007     

Single electron transfer‐living radical polymerization of methyl methacrylate in fluoroalcohol: Dual control over molecular weight and tacticity

The Cu(0)‐mediated single electron transfer‐living radical polymerization (SET‐LRP) of methyl methacrylate (MMA) using ethyl 2‐bromoisobutyrate (EBiB) as an initiator with Cu(0)/N,N,N′,N′′,N′′‐pentamethyldiethylenetriamine as a catalyst system in 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was studied. The polymerization showed some living features: the measured number‐average molecular weight (M_n,GPC) increased with monomer conversion and produced polymers with relatively low polydispersities. The increase of HFIP concentration improved the controllability over the polymerization with increased initiation efficiency and lowered polydispersity values. ¹H NMR, MALDI‐TOF‐MS spectra, and chain extension reaction confirmed that the resultant polymer was end‐capped by EBiB species, and the polymer can be reactivated for chain extension. In contrast, in the cases of dimethyl sulfoxide or N,N‐dimethylformamide as reaction solvent, the polymerizations were uncontrolled. The different effects of the solvents on the polymerization indicated that the mechanism of SET‐LRP differed from that of atom transfer radical polymerization. Moreover, HFIP also facilitated the polymerization with control over stereoregularity of the polymers. Higher concentration of HFIP and lower reaction temperature produced higher syndiotactic ratio. The syndiotactic ratio can be reached to about 0.77 at 1/1.5 (v/v) of MMA/HFIP at ?18 °C. In conclusion, using HFIP as SET‐LRP solvent, the dual control over the molecular weight and tacticity of PMMA was realized. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6316–6327, 2009     

Precisely controlled copper(0)‐catalyzed one‐pot reaction: Concurrent living radical polymerization and click chemistry

Copper(0)‐catalyzed one‐pot reaction combining living radical polymerization and “click chemistry” was investigated. By precisely tuning reaction time, three novel well‐defined polymers with different degree of carboxyl substitution, poly(propargyl methacrylate) (PPgMA), poly(1‐(4‐carboxyphenyl)‐[1,2,3]triazol‐4‐methyl methacrylate) (PCTMMA), and poly(1‐(4‐carboxyphenyl)‐[1,2,3]triazol‐4‐methyl methacrylate‐co‐propargyl methacrylate) (PCTMMA‐co‐PPgMA) were selectively obtained via Cu(0) powder/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) cocatalyzed LRP and click chemistry. In addition, gel permeation chromatography and ¹H NMR analysis in conjunction with FTIR spectroscopy elucidate that one‐pot process undergoes three steps due to a pronounced rate enhancement of click reaction: (1) generating new monomer, 1‐(4‐carboxyphenyl)‐[1,2,3]triazol‐4‐methyl methacrylate (CTMMA); (2) copolymerization of two monomers (CTMMA and PgMA); (3) building homopolymer PCTMMA. Surprisingly, in contrast to typical Cu(I)‐catalyzed atom transfer radical polymerization (ATRP), copper(0)‐catalyzed one‐pot reaction showed high carboxylic acid group tolerance. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Single‐electron transfer‐living radical copolymerization of butyl methacrylate and divinylbenzene for preparation of oil‐absorbing gel

Crosslinking copolymerization of butyl methacrylate with a small amount of divinylbenzene (DVB) was carried out using single‐electron transfer‐living radical polymerization initiated with carbon tetrachloride (CCl₄) and catalyzed by Cu(0)/N‐ligand in N,N‐dimethylformamide to produce a highly oil‐absorbing gel. The polymerization, gelation process, and oil‐absorbing properties were studied in detail. Analysis of monomer conversion with reaction time showed that the polymerization followed first‐order kinetics for both linear and crosslinking polymerization before gelation. Higher levels of DVB led to earlier gelation and the influence of N‐ligand on gelation was also significant. Under optimal conditions, oil absorption of the prepared gel to chloroform could reach 42.1 g·g^?1. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3233–3239     

SET‐LRP of acrylates in the presence of radical inhibitors

The Cu(0)/Me₆‐TREN‐catalyzed single‐electron transfer mediated living radical polymerization (SET‐LRP) of methyl acrylate in the presence of the classic 4‐methoxyphenol free radical inhibitor was investigated. Kinetic experiments, combined with ¹H NMR, and MALDI‐TOF MS analysis of the resulting polyacrylates demonstrated that SET‐LRP is a robust synthetic method that does not require the purification of the monomers to remove the radical inhibitor. It is anticipated that these results will contribute to the expansion of technological and fundamental applications of SET‐LRP since it allows the synthesis of polymers with a structural perfection that previously was not accessible by any other method, starting from unpurified monomers, solvents, initiators, and ligands. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3174–3181, 2008     

Effect of catalyst systems and reaction conditions on the synthesis of cellulose‐g‐PDMAam copolymers by controlled radical polymerization

Various copper‐based catalyst systems and reaction conditions were studied in the graft copolymerization of N,N‐dimethylacrylamide (DMAam) with a cellulose‐based macroinitiator by controlled radical polymerization. The cellulose macroinitiator with degree of substitution DS = 0.44 was synthesized from dissolving softwood pulp in a LiCl/DMAc solution. The graft copolymerizations of DMAam, using the cellulose macroinitiator and various copper‐based catalyst systems, were then carried out in DMSO solutions. The copolymerization kinetics was followed by ¹H NMR. Water‐soluble cellulose‐g‐PDMAam copolymers were comprehensively characterized by ATR‐FTIR and ¹H NMR spectroscopies and SEC analyses. DLS and steady‐shear viscosity measurements revealed that when the DP_graft of the cellulose‐g‐PDMAam copolymer is high enough, the copolymer forms a more compact structure in water. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and properties of Q‐silicon crosslinked siloxane networks: H3PO4‐catalyzed sol–gel dehydration/crosslinking of α,ω‐bis(hydroxy)oligodimethylsiloxanes with tetrakis(hydroxydimethylsiloxy)silane

Six silicate‐crosslinked oligodimethylsiloxane thin films were prepared by the phosphoric acid (1 mol %) catalyzed condensation of α,ω‐bis(hydroxy)oligodimethylsiloxane (P) and tetrakis(hydroxydimethylsiloxy)silane (Q). Other acid catalysts were evaluated. P and Q were prepared by the Pd‐catalyzed oxidation of the corresponding Si? H compounds with water. The starting materials were characterized by IR and ¹H, ¹³C, and ²⁹Si NMR. A thermal cure was achieved with H₃PO₄ in 24 h and with poly(phosphoric acid) in 3 h at 110–120 °C. Dynamic mechanical analysis was used to determine the glass‐transition temperatures and to evaluate the mechanical properties of the films. Their thermal stabilities (≥300 °C) in air and N₂ were determined by thermogravimetric analysis. Small amounts of non‐crosslinked P were recovered from the films by Soxhlet extractions with CH₂Cl₂ and analyzed by IR, gel permeation chromatography, and ²⁹Si NMR. The crosslink densities were evaluated by the CH₂Cl₂ absorption capacities of the films. The surface properties of the films were determined by static and dynamic contact‐angle measurements. Electrochemical impedance spectroscopy was carried out to evaluate the corrosion‐protective properties of the coatings on mild steel as a function of the exposure time to 0.5 N NaCl. The biofoul‐release properties of the films were evaluated with sporelings from mature Ulva linza plants and barnacles. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2237–2247, 2006     

Synthesis and characterization of functional gradient copolymers of allyl methacrylate and butyl acrylate

Functional spontaneous gradient copolymers of allyl methacrylate (A) and butyl acrylate (B) were synthesized via atom transfer radical polymerization. The copolymerization reactions were carried out in toluene solutions at 100 °C with methyl 2‐bromopropionate as the initiator and copper bromide with N,N,N′,N″,N″‐pentamethyldiethylenetriamine as the catalyst system. Different aspects of the statistical reaction copolymerizations, such as the kinetic behavior, crosslinking density, and gel fraction, were studied. The gel data were compared with Flory's gelation theory, and the sol fractions of the synthesized copolymers were characterized by size exclusion chromatography and nuclear magnetic resonance spectroscopy. The copolymer composition, demonstrating the gradient character of the copolymers, and the microstructure were analyzed. The experimental data agreed well with data calculated with the Mayo–Lewis terminal model and Bernoullian statistics, with monomer reactivity ratios of 2.58 ± 0.37 and 0.51 ± 0.05 for A and B, respectively, an isotacticity parameter for A of 0.24, and a coisotacticity parameter of 0.33. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5304–5315, 2006     

SET‐LRP of vinyl chloride initiated with CHBr3 in DMSO at 25 °C

The development of Cu(0)/TREN/CuBr₂‐catalyzed SET‐LRP of VC initiated with CHBr₃ in DMSO at 25 °C is reported. The use of CuBr₂ additive allows for the first LRP of low molecular weight VC (target DP = 100), as well as lower Cu powder loading levels, improved I_eff and control in the synthesis of higher molecular VC, targeted degree of polymerization = 350, 700, 1,000, 1,400. ¹H NMR and HSQC confirm the bifunctionality of CHBr₃ as an initiator and suggest that deleterious side‐reactions such as the formation of allylic chlorides occur primarily at the onset of the reaction. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4130–4140, 2009