Synthesis of poly(L‐lactide)‐grafted pullulan through coupling reaction between amino group end‐capped poly(L‐lactide) and carboxymethyl pullulan and its aggregation behavior in water

Poly(L ‐lactide) (PLLA) with terminal primary amino groups (PLLA‐NH₂) was synthesized and used to construct PLLA‐grafted pullulan (Pul‐g‐PLLA). It consisted of a hydrophilic carboxymethyl Pul (CM‐Pul) main chain and hydrophobic PLLA graft chains that were created through a direct coupling reaction between PLLA‐NH₂ and CM‐Pul using 2‐ethoxy‐1‐(ethoxycarbonyl)‐1,2‐dihydroquinoline as a condensation reagent. Pul‐g‐PLLAs with over 78 wt % sugar unit content were found to form nanometer‐sized aggregates in water. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5482–5487, 2004     

Biodegradable stereocomplex materials of polylactide‐grafted dextran exhibiting soft and tough properties in dry and wet states

Water‐swellable biodegradable materials exhibiting mechanically tenacious and tough characters in the wet state were prepared by a simple blend of two enantiomeric polylactide‐grafted dextran copolymers (Dex‐g‐PLLA and Dex‐g‐PDLA). DSC and WAXD analyses demonstrated the formation of SC crystals in the copolymer blend films. SC blend films showed lamellar‐type microphase‐separated structures. When swollen with water, these blend films showed the same level of tensile strengths and Young's modulus as the films in the dry state. SC blend films degraded gradually over a month under physiological conditions with a degradation rate faster than the corresponding Dex‐g‐PLLA films. The SC‐forming enantiomeric mixture of polylactide‐grafted polysaccharides should be a good candidate for an implantable biocompatible material exhibiting favorable mechanical properties and degradation behavior. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Nanoindentation of biodegradable cellulose diacetate‐graft‐poly(L‐lactide) copolymers: Effect of molecular composition and thermal aging on mechanical properties

Nanoindentation of cellulose diacetate‐graft‐poly(lactide)s (CDA‐g‐PLLAs) synthesized by ring opening graft copolymerization of L ‐lactide in bulk onto the residual hydroxyl positions on CDA were conducted to investigate the effect of the molecular composition and thermal aging on mechanical properties and creep behavior. Continuous stiffness measurement (CSM) technique was used to obtained hardness and elastic modulus. These material properties were expressed as a mean value from 100 to 300 nm depths and an unloading value at final indentation depth. The hardness and elastic modulus in all CDA‐g‐PLLAs were higher than those in pure CDA, indicating that the introduction of PLLA increases the hardness and elastic modulus. With an increase of crystallinity by thermal aging, the hardness and elastic modulus were increased in both CDA‐g‐PLLA and PLLA. The creep test performed by CSM showed that the creep strain of CDA was decreased by the grafting of PLLA. Thermal aging decreased the creep strain of CDA‐g‐PLLA and PLLA. With an increase of holding time, hardness was decreased, whereas elastic modulus was kept almost constant. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1114–1121, 2007     

Effects of top confinement and diluents on morphology in crystallization of poly(l‐lactic acid) interacting with poly(ethylene oxide)

Effects of top confinement and diluent poly(ethylene oxide) (PEO) on poly(l ‐lactic acid) (PLLA) crystal morphology have been investigated. When crystallized at 120 °C, uncovered neat PLLA sample exhibits higher growth rate ringless spherulites; while the covered sample exhibits lower growth rate ring‐banded spherulites. As PEO is introduced into PLLA, the morphology also undergoes significant changes. For the same T_c,PLLA = 120 °C, the PEO/PLLA blend with PEO composition greater than 25% exhibits ring‐banded patterns even in uncovered sample. However, in much greater PEO composition (>80 wt %), uncovered samples exhibit ring bands diverging into dendritic patterns, while top covered samples tend to maintain the spiral ring‐band patterns. Both PEO inclusion in PLLA and top cover on films impose growth kinetic alterations. Additionally, the top glass cover tends to prevent the lower surface tension PLLA to be accumulated on the surface, resulting in the formation of ring‐band pattern. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1160–1170     

Poly(L‐lactide)/C60 nanocomposites: Effects of C60 on crystallization of poly(L‐lactide)

The effects of solvent type and concentration of C₆₀ on the crystallization of poly(L ‐lactide) (PLLA) during solvent evaporation, heating from room temperature, and cooling from the melt were investigated by polarized optical microscopy and differential scanning calorimetry. The addition of C₆₀ enhanced the PLLA crystallization during solvent evaporation, during heating of the melt‐quenched films, and during cooling from the melt of As‐cast films, except for heating and cooling of the PLLA film with 1 wt % of C₆₀ prepared with dichloromethane. In the case of solvent evaporation, the difference in crystallinity between the PLLA films with and without C₆₀ became higher for the solvent with a lower boiling point. In the case of heating of melt‐quenched films, the addition of C₆₀ had a small effect on the crystallinity of PLLA, whereas significantly lowered the peak top and ending temperatures of cold crystallization, except for melt‐quenched PLLA film with 1 wt % of C₆₀ prepared with dichloromethane. The crystallinity of PLLA was determined by the solvent type, rather than by the C₆₀ concentration. In the case of cooling from the melt of As‐cast films, the addition of C₆₀ elevated the crystallinity and cold crystallization temperature values of PLLA films, except for PLLA films prepared with dichloromethane. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2167–2176, 2007     

Synthesis and new application of green and recyclable cyclic poly(L‐lactide)‐clay hybrid

We report on the application of biodegradable cyclic poly(L ‐lactide) (PLLA) as new stabilizer; synthesis and application of a cyclic PLLA‐clay hybrid material as recyclable catalyst support. Cyclic PLLAs were used to stabilize palladium nanoparticles synthesized by a wet chemical method. It was found that the palladium particles were smaller with cyclic PLLA stabilizer (～5–10 nm) than the particles obtained from linear PLLA. The cyclic PLLA‐clay hybrid was prepared by a zwitterionic ring‐opening polymerization catalyzed by in situ‐generated N‐heterocyclic carbene catalyst. Palladium (0) nanoparticles were supported and well dispersed on the cyclic PLLA‐clay hybrid to form a new nanocomposite. The nanocomposite was found to be a highly efficient and recyclable catalyst for the aminocarbonylation reactions of aryl halides with various amines. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4167–4174     

Synthesis and characterization of poly(vinyl amine)‐based amphiphilic comb‐like dextran glycopolymers by a two‐step method

Poly(vinyl amine) (PVAm)‐based amphiphilic glycopolymers were synthesized by a two‐step method, that is dextran molecules (Dex, M_w = 1500) were attached to the PVAm backbone by reacting amine groups with dextran lactone, and then, hexanoyl groups (Hex) were attached by reacting the PVAm free amine groups with N‐(hexanoyloxy)succinimide. By adjustment of the feed ratios of Dex/Hex, amphiphilic comb‐like glycopolymers with various hydrophilic and hydrophobic balances were prepared, and their structures were characterized by ¹H NMR. Surface activity of the amphiphilic glycopolymers at the air/water interface was demonstrated by reduction in water surface tension. Adsorption of the amphiphilic glycopolymers at the solid/water interface was examined on octadecyltrichlorosilane (OTS)‐coated coverslips by water contact angle measurements. The results show that the amphiphilic glycopolymers need about 20 mol % of dextran attachment to make an effective hydrophilic coating. In comparison with the one‐step reaction by addition of dextran lactone and alkyl succinimide simultaneously, the two‐step approach can attach Dex on PVAm as high as possible in the first step, and offers quantitative advantages in controlling the ratio of hydrophilic and hydrophobic chains along the PVAm backbone, resulting in increased water solubility for the final amphiphilic glycopolymers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 192–199, 2006     

Synthesis of biodegradable thermoplastic elastomers from ε‐caprolactone and lactide

This article reports the synthesis and the properties of novel thermoplastic elastomers of A‐B‐A type triblock copolymer structure, where the hard segment A is poly(l ‐lactide) (PLLA) and the soft segment B is poly(ε‐caprolactone‐stat‐d ,l ‐lactide) (P(CL‐stat‐DLLA)). The P(CL‐stat‐DLLA) block with DLLA content of 30 mol % was applied because of its amorphous nature and low glass transition temperature (T_g = approximately ?40 °C). Successive polymerization of l ‐lactide afforded PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLAs, which exhibited melting temperature (T_m = approximately 150 °C) for the crystalline PLLA segments and still low T_g (approximately ?30 °C) of the soft segments. The triblock copolymers showed very high elongation at break up to approximately 2800% and elastic properties. The corresponding d ‐triblock copolymers, PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLAs (PDLA = poly(d ‐lactide)) were also prepared with the same procedure using d ‐lactide in place of l ‐lactide. When the PLLA‐block‐P(CL‐stat‐DLLA)‐block‐PLLA was blended with PDLA‐block‐P(CL‐stat‐DLLA)‐block‐PDLA, stereocomplex crystals were formed to enhance their T_m as well as tensile properties. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 489–495     

Alkaline and enzymatic degradation of L‐lactide copolymers. II. Crystallized films of poly(L‐lactide‐co‐D‐lactide) and poly(L‐lactide) with similar crystallinities

Films of poly(L ‐lactide‐co‐D ‐lactide) [P(LLA‐DLA); 95/5] and poly(L ‐lactide) [i.e., poly(L ‐lactide acid) (PLLA)] were prepared by crystallization from the melt, and a comparative study of the crystallization effects on the alkaline and proteinase K catalyzed hydrolysis of the films was carried out. The hydrolyzed films were investigated with gravimetry, differential scanning calorimetry, polarimetry, and gel permeation chromatography, and the results were compared with those reported for amorphous‐made specimens. The alkaline hydrolyzability of the P(LLA‐DLA) (95/5) and PLLA films was determined solely by the initial crystallinity (X_c) and was not affected by the content of the incorporated D ‐lactide (DLA) unit in the polymer chain; this was in marked contrast to the fact that the enzymatic hydrolyzability depended on not only the initial X_c value but also the DLA unit content. The alkaline hydrolysis rate of the P(LLA‐DLA) (95/5) and PLLA films and the enzymatic hydrolysis rate (R_EH) of the P(LLA‐DLA) (95/5) films decreased linearly as the initial X_c value increased. This meant that the hydrolyzability of the restricted amorphous regions was very similar to that of the free amorphous regions. In contrast, R_EH of the PLLA films decreased nonlinearly with the initial X_c value, and this nonlinear dependence was caused by the fact that in the PLLA films the restricted amorphous regions were much more hydrolysis‐resistant than the free amorphous regions. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1064‐1075, 2005     

Formation of CdS nanoclusters in phase‐separated poly(2‐hydroxyethyl methacrylate)‐l‐polyisobutylene amphiphilic conetworks

Nanophase‐separated poly(2‐hydroxyethyl methacrylate)‐l‐polyisobutylene (PHEMA‐l‐PIB) amphiphilic conetworks were obtained by crosslinking α,ω‐bismethacrylate‐terminated polyisobutylene (PIB) via copolymerization with silylated 2‐hydroxyethyl methacylate, followed by the hydrolysis of the silylether groups. Morphology development of a sample containing 64% PIB was monitored by means of transmission electron microscopy (TEM), atomic force microscopy (AFM), and small‐angle X‐ray scattering. For comparison, the morphology of a sample containing 53% PIB was investigated by AFM. The dry conetworks exhibited hydrophilic and hydrophobic phases with average 8–10‐nm domain sizes and were swellable in water as well as in heptane. Swelling amphiphilic conetworks with aqueous cadmium–chloride solution followed by exposure to H₂S resulted in nanosized CdS clusters located in the amphiphilic conetworks, that is, for the first time, new inorganic–organic hybrid materials composed of CdS semiconducting nanocrystals and PHEMA‐l‐PIB amphiphilic conetworks were prepared. © 2001 John Wiley & Sons, Inc. J Polym Sci B Part B: Polym Phys 39: 1429–1436, 2001     

Effects of carbon nanotubes on crystallization and melting behavior of poly(L‐lactide) via DSC and TMDSC studies

In this work, multiwalled carbon nanotubes (MWNTs) were surface‐modified and grafted with poly(L ‐lactide) to obtain poly(L ‐lactide)‐grafted MWNTs (i.e. MWNTs‐g‐PLLA). Films of the PLLA/MWNTs‐g‐PLLA nanocomposites were then prepared by a solution casting method to investigate the effects of the MWNTs‐g‐PLLA on nonisothermal and isothermal melt‐crystallizations of the PLLA matrix using DSC and TMDSC. DSC data found that MWNTs significantly enhanced the nonisothermal melt‐crystallization from the melt and the cold‐crystallization rates of PLLA on the subsequent heating. Temperature‐modulated differential scanning calorimetry (TMDSC) analysis on the quenched PLLA nanocomposites found that, in addition to an exothermic cold‐crystallization peak in the range of 80–120 °C, an exothermic peak in the range of 150–165 °C, attributed to recrystallization, appeared before the main melting peak in the total and nonreversing heat flow curves. The presence of the recrystallization peak signified the ongoing process of crystal perfection and, if any, the formation of secondary crystals during the heating scan. Double melting endotherms appeared for the isothermally melt‐crystallized PLLA samples at 110 °C. TMDSC analysis found that the double lamellar thickness model, other than the melting‐recrystallization model, was responsible for the double melting peaks in PLLA nanocomposites. Polarized optical microscopy images found that the nucleation rate of PLLA was enhanced by MWNTs. TMDSC analysis found that the incorporation of MWNTs caused PLLA to decrease the heat‐capacity increase (namely, ΔC_p) and the C_p at glass transition temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1870–1881, 2007     

Interlocking layer structures formed in spin‐cast polymer blend films by surface segregation and self‐stratification

Surface morphologies formed by the phase segregation of poly(styrene‐b‐ethylene/butylene‐b‐styrene) (SEBS)/poly(methyl methacrylate) (PMMA) blend films prepared via spin coating on mica substrates were studied with atomic force microscopy accompanied by a solvent extraction treatment, X‐ray photoelectron spectroscopy, and contact‐angle measurements. Three kinds of surface structures of films were observed. Besides the ribbonlike morphology and the dispersed domains in a continuous matrix that are common in this field, we found a special interlocking layer structure characterized by a smooth SEBS layer as the cover on the top and a layer composed of hill‐like PMMA dispersed in the SEBS matrix at the bottom when the composition of the film was around 50:50 SEBS and PMMA. A series of blend films with different thicknesses were then prepared to investigate the interfacial structure, and the formation process of the interlocking layer, which could be elucidated by a schematic diagram, was discussed. The interlocking bilayer film with SEBS on the top possessed high thermal stability and the best surface roughness in comparison with other structures. It might find important technical applications in fields such as adhesion, lubrication, and protective coatings. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 532–543, 2007.     

Immiscibility–miscibility phase transformation in blends of poly(ethylene succinate) with poly(L‐lactic acid)s of different molecular weights

Using differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and Fourier transformed infrared spectroscopy (FTIR), upper critical solution temperature (UCST) phase behavior with immiscibility–miscibility transformation in blends of poly(ethylene succinate) (PESu) with poly(lactic acid)s (PLAs), such as poly(D ,L ‐lactic acid) (PDLLA), poly(L ‐lactic acid) (PLLA), poly(D ‐lactic acid) (PDLA), differing in D/L configurations and molecular weights were investigated. All three binary blends of PDLLA/PESu, PLLA/PESu, and PESu/PDLA exhibit UCST behavior, which means they are immiscible at ambient temperature but can become miscible upon heating to higher temperatures at 240–268 °C depending on molecular weights. The PLLAs/PESu blends at UCST could be reverted back to the original phase‐separated morphology, as proven by solvent redissolution. The blends upon quenching from above UCST could be frozen into a quasi‐miscible state, where the Flory‐Huggins interaction parameter (χ₁₂) was determined to be a negative value (by melting point depression technique). The interaction between PDLLA and PESu in blend resulted in significant reduction in spherulite growth rate of PESu. Furthermore, blends of PESu with lower molecular weight PLLA or PDLA (M_w of PLLA and PDLA are 152,000 and 124,000 g/mol, respectively), instead of the higher M_w of PDLLA (M_w of PDLLA = 157,000 g/mol), are immiscible with UCST phase behavior, which are affected by molecular weights rather than the ratio of L/D monomer in the chemical structure of PLAs. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1135–1147, 2010     

Complex,degradable polyester materials via ketoxime ether‐based functionalization: Amphiphilic,multifunctional graft copolymers and their resulting solution‐state aggregates

Degradable, amphiphilic graft copolymers of poly(ε‐caprolactone)‐graft‐poly(ethylene oxide), PCL‐g‐PEO, were synthesized via a grafting onto strategy taking advantage of the ketones presented along the backbone of the statistical copolymer poly(ε‐caprolactone)‐co‐(2‐oxepane‐1,5‐dione), (PCL‐co‐OPD). Through the formation of stable ketoxime ether linkages, 3 kDa PEO grafts and p‐methoxybenzyl side chains were incorporated onto the polyester backbone with a high degree of fidelity and efficiency, as verified by NMR spectroscopies and GPC analysis (90% grafting efficiency in some cases). The resulting block graft copolymers displayed significant thermal differences, specifically a depression in the observed melting transition temperature, T_m, in comparison with the parent PCL and PEO polymers. These amphiphilic block graft copolymers undergo self‐assembly in aqueous solution with the P(CL‐co‐OPD‐co‐(OPD‐g‐PEO)) polymer forming spherical micelles and a P(CL‐co‐OPD‐co‐(OPD‐g‐PEO)‐co‐(OPD‐g‐pMeOBn)) forming cylindrical or rod‐like micelles, as observed by transmission electron microscopy and atomic force microscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3553–3563, 2010     

Crystallization and morphology of poly(ethylene oxide‐b‐lactide) crystalline–crystalline diblock copolymers

The crystallization behaviors and morphology of asymmetric crystalline–crystalline diblock copolymers poly(ethylene oxide‐lactide) (PEO‐b‐PLLA) were investigated using differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and microscopic techniques (polarized optical microscopy (POM) and atomic force microscopy (AFM)). Both blocks of PEO₅‐b‐PLLA₁₆ can be crystallized, which was confirmed by WAXD, while PEO block in PEO₅‐b‐PLLA₃₀ is difficult to crystallize because of the confinement induced by the high glass transition temperature and crystallization of PLLA block with the microphase separation of the block copolymer. Comparing with the crystallization and morphology of PLLA homopolymer and differences between the two copolymers, we studied the influence of PEO block and microphase separation on the crystallization and morphology of PLLA block. The boundary temperature (T_b) was observed, which distinguishes the crystallization into high‐ and low‐temperature ranges, the growth rate and morphology were quite different between the ranges. Crystalline morphologies including banded spherulite, dendritic crystal, and dense branching in PEO₅‐b‐PLLA₁₆ copolymer were formed. The typical morphology of dendritic crystals including two different sectors were observed in PEO₅‐b‐PLLA₃₀ copolymer, which can be explained by secondary nucleation, chain growth direction, and phase separation between the two blocks during the crystallization process. Lozenge‐shaped crystals of PLLA with screw dislocation were also observed employing AFM, but the crystalline morphology of PEO block was not observed using microscopy techniques because of its small size. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1400–1411, 2008     

Microstructure and properties of 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyimide/poly(vinylsilsesquioxane) hybrid nanocomposite films

Hybrid nanocomposite films of poly(vinylsilsesquioxane) (PVSSQ) and polyimide (PI) (PI/PVSSQ) were prepared via sol‐gel process from triethoxyvinylsilane (VSSQ) and thermal imidization from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyamic acid (BPDA‐PDA PAA). We investigated the microstructure; interfacial interaction; and optical, thermal, dielectric, and mechanical properties of the hybrid films. The phase morphologies and degree of surface roughness were evaluated by scanning electron microscope (SEM) and atomic force microscope (AFM), respectively. It was found that the surface topography was influenced by the composition of PVSSQ. Hydrogen bonding interactions between polyimide (PI) matrix and PVSSQ domains were proved with FT‐IR spectroscopy. The transparency of the hybrid films was found to be dependent on the PVSSQ content. Incorporating of the PVSSQ in the hybrid composites increased the glass transition temperature of PI. Dielectric constants of the hybrid films were in the range of 2.37–3.59. Properties of the PI films were also significantly enhanced by adding 5–30 wt % of PVSSQ. For comparison, we also prepared the hybrid composites of PI and mixtures of VSSQ and tetraethoxysilane (TEOS) and the PI/silica hybrid composite containing 30 wt % of silica obtained from TEOS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5189–5199, 2004     

Synthesis,self‐assembly,and thermosensitive properties of ethyl cellulose‐g‐P(PEGMA) amphiphilic copolymers

Ethyl cellulose graft poly(poly(ethylene glycol) methyl ether methacrylate) (EC‐g‐P(PEGMA)) amphiphilic copolymers were synthesized via atom transfer radical polymerization (ATRP) and characterized by FTIR, ¹H NMR, and gel permeation chromatography. Reaction kinetics analysis indicated that the graft copolymerization is living and controllable. The self‐assembly and thermosensitive property of the obtained EC‐g‐P(PEGMA) amphiphilic copolymers in water were investigated by dynamic light scattering, transmission electron microscopy, and transmittance. It was found that the EC‐g‐P(PEGMA) amphiphilic copolymers can self‐assemble into spherical micelles in water. The size of the micelles increases with the increase of the side chain length. The spherical micelles show thermosensitive properties with a lower critical solution temperature around 65 °C, which almost independent on the graft density and the length of the side chains. The obtained EC‐g‐P(PEGMA) graft copolymers have both the unique properties of poly(ethylene glycol) and cellulose, which may have the potential applications in biomedicine and biotechnology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 46: 6907–6915, 2008     

Amphiphilic silica/fluoropolymer nanoparticles: Synthesis,tem‐responsive and surface properties as protein‐resistance coatings

A series of amphiphilic silica/fluoropolymer nanoparticles of SiO₂‐g‐P(PEGMA)‐b‐P(12FMA) were prepared by silica surface‐initiating atom transfer radical polymerization (SI‐ATRP) of poly(ethylene glycol) methyl ether methacrylate (PEGMA) and poly dodecafluoroheptyl methacrylate (P12FMA). Their amphiphilic behavior, lower critical solution temperature (LCST), and surface properties as protein‐resistance coatings were characterized. The introduction of hydrophobic P(12FMA) block leads SiO₂‐g‐P(PEGMA)‐b‐P(12FMA) to form individual spherical nanoparticles (～150 nm in water and ～170 nm in THF solution) as P(PEGMA)‐b‐P(12FMA) shell grafted on SiO₂ core (～130 nm), to gain obvious lower LCST at 36–52 °C and higher thermostability at 290–320 °C than SiO₂‐g‐P(PEGMA) (LCST = 78–90 °C, T_d = 220 °C). The water‐casted SiO₂‐g‐P(PEGMA)‐b‐P(12FMA) films obtain much rougher surface (125.3–178.4 nm) than THF‐casted films (11.5–16.9 nm) and all SiO₂‐g‐P(PEGMA) films (26.8–31.3 nm). Therefore, the water‐casted surfaces exhibit obvious higher water adsorption amount (Δf = ?494 ～ ?426 Hz) and harder adsorbed layer (viscoelasticity of ΔD/Δf = ?0.28 ～ ?0.36 × 10^?6/Hz) than SiO₂‐g‐P(PEGMA) films, but present loser adsorbed layer than THF‐casted films (ΔD/Δf = ?0.29 ～ ?0.63 × 10^?6/Hz). While, the introduction of P(12FMA) segments does not show obviously reduce in the protein‐repelling adsorption of SiO₂‐g‐P(PEGMA)‐b‐P(12FMA) films (△f = ?15.7 ～ ?22.3 Hz) compared with SiO₂‐g‐P(PEGMA) films (△f = ?8.3 ～ ?11.3 Hz) and no obvious influence on water adsorption of ancient stone. Therefore, SiO₂‐g‐P(PEGMA)‐b‐P(12FMA) is suggested to be used as protein‐resistance coatings. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 381–393     

Templated synthesis of silver nanoparticles in amphiphilic poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) comb copolymer

In this study, poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(oxyethylene methacrylate), P(VDF‐co‐CTFE)‐g‐POEM, an amphiphilic comb copolymer with hydrophobic P(VDF‐co‐CTFE) backbone and hydrophilic POEM side chains at 73:27 wt % was synthesized. The POEM side chains were grafted from the P(VDF‐co‐CTFE) mainchain backbone via atom transfer radical polymerization (ATRP) using direct initiation of the chlorine atoms in CTFE units. Synthesis of microphase‐separated P(VDF‐co‐CTFE)‐g‐POEM comb copolymer was successful, as confirmed by nuclear magnetic resonance (¹H NMR), FTIR spectroscopy, and transmission electron microscopy (TEM). Nanocomposite films were prepared using the comb copolymer as a template film and the in situ reduction of AgCF₃SO₃ precursor to silver nanoparticles under UV irradiation. Silver nanoparticles with 4–8 nm in average size were in situ created in the solid state template film, as revealed by TEM, UV–visible spectroscopy, and wide angle X‐ray scattering (WAXS). Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) presented the selective incorporation and the in situ growth of silver nanoparticles within the hydrophilic POEM domains of microphase‐separated comb copolymer film. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 702–709, 2008     

Syntheses,characterization, and properties of multiblock copolymers consisting of polyisobutylene and poly(L‐lactide) segments

The syntheses of {‐poly(L ‐lactide) (PLLA)‐b‐polyisobutylene (PIB)‐}_n multiblock copolymers were accomplished for the first time by chain extension of PLLA‐b‐PIB‐b‐PLLA triblock copolymers. Well‐defined PLLA‐b‐PIB‐b‐PLLA triblock copolymers with predictable M_ns, low PDIs (1.10–1.18) and excellent blocking efficiencies were prepared by anionic ring‐opening polymerizations of L ‐lactide initiated with hydroxyallyl telechelic PIB (HO‐Allyl‐PIB‐Allyl‐OH) in toluene at 110 °C. The triblock copolymers were successfully chain extended with 4,4′‐methylenebis(phenylisocyanate) (MDI) to obtain the multiblock copolymers with good gravimetric yields of ～86 to 96%. The chain‐extended polymers were soluble in a range of common organic solvents. The block copolymers showed two glass transition temperatures in differential scanning calorimetric analysis for the PIB and PLLA blocks indicating microphase separation, which was supported by atomic force microscopy images. The as‐synthesized compression molded multiblock copolymers exhibited tensile strengths in the range of 8–24 MPa with elongations at break in the range of 2.5–400%. The static and dynamic mechanical properties showed a strong dependence on the relative PLLA content in the copolymer. The dynamic mechanical analysis also indicated microphase separation at higher PLLA compositions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3490–3505, 2009