Synthesis and spectroscopic characterization of gold nanoparticles

Photoluminescent nanoparticles of gold with size 3, 4, 6, and 9nm are prepared by borohydride/citrate reduction in presence of polyethylene glycol (PEG)/tannic acid. The prepared nanomaterials are characterized by UV-vis spectroscopy and dynamic light scattering (DLS) technique. Intense photoluminescence (PL) is observed in nanoparticles prepared by fast reduction with borohydride in presence of PEG. A red shift of PL emission from 408 to 456nm is observed for the change of size from 4 to 6nm. Increase in PL intensity is observed for all the nanoparticles on the addition of KCl. Citrate reduced gold colloid which consists of large particles of size approximately 35nm with anisotropic shapes showing two plasmon peaks is also prepared. The anisotropy is confirmed by TEM measurement. SERS activity of this colloid is tested using glutamic acid as an adsorbate probe. Assignment of the observed bands is given.     

Synthesis and characterization of thiosalicylic acid stabilized gold nanoparticles

We report the synthesis of photoluminescent Au nanoparticles of varying sizes stabilized with a carboxylate group terminated aromatic thiol, thiosalicylic acid. The formation of Au nanoparticles and its stabilization with the thiol has been characterized by different spectroscopic and thermal methods. The water solubility, along with the low degree of aggregation and photoluminescence, enhances their suitability for biological applications. The photoluminescence may be due to charge transfer of the Au core with the stabilizing ligand.     

Synthesis and characterization of Au core-Au-Ag shell nanoparticles from gold seeds: impacts of glycine concentration and pH

This paper describes the preparation of Au core-Au-Ag shell nanoparticles (NPs) in different morphologies by controlling both the pH and the glycine concentration. Using a seed-growth method, we prepared high-quality Au core-Au-Ag shell NPs from a glycine solution under alkaline conditions (pH>8.5). By controlling both the pH and the glycine concentration, we prepared dumbbell-shaped and peanut-shaped Au core-Au-Ag shell NPs readily by depositing gold and silver, reduced by ascorbate, onto the gold nanorods. We have found that the glycine concentration that is optimal for preparing high-quality Au core-Au-Ag shell NPs differs at the various values of pH. At pH<8.5, the glycine concentration is not important, but, when preparing dumbbell- and peanut-shaped Au core-Au-Ag shell NPs, it should be greater than 50 mM and greater than 20 mM at pH 9.5 and 10.5, respectively. Glycine plays a number of roles during the synthesis of the Au core-Au-Ag shell NPs by controlling the solution pH, altering the reduction potentials of gold and silver ions through forming complexes with metal ions (Au(+) and Ag(+)), minimizing the formation of Ag(2)O, AgCl, and AgBr precipitates, and stabilizing the thus-prepared NPs. At pH 9.7, we observed the changes in the morphologies of the Au core-Au-Ag shell NPs-from regular (rectangular) to peanut- and dumbbell-shaped, and finally to jewel-, diamond-, and/or sphere-shaped-that occurred during the course of a 60-min reaction. In addition, we were able to affect the shapes and sizes of the Au core-Au-Ag shell NPs by controlling the reaction time.     

Block copolymer-mediated synthesis of size-tunable gold nanospheres and nanoplates

We have successfully controlled the size and shape of isotropic and anisotropic gold nanocrystals through a one-step reaction by using amphiphilic polyethylene oxide-polystyrene oxide block copolymers as both reductant and stabilizing agents in water solution. Spherical or quasispherical nanoparticles were obtained at room temperature with tunable mean sizes and polydispersities depending on reaction conditions, that is, on copolymer block length, and copolymer and gold salt concentrations. By moderate increases of reaction temperature up to 65 degrees C, progressive formation of single-crystalline gold nanoplates in good yields takes place (up to 70%) without the necessity of additional reactants or growing solutions. These nanoplates are characterized by lateral mean sizes between 0.1-1.2 microm depending on copolymer concentration and reaction temperature, with mainly truncated or rounded triangular shapes with {111} planes as two basal surfaces. This allows us to tune the surface plasmon band of the nanoplates from ca. 850 nm to more than 1100 nm, well inside the near-infrared region (NIR), which enables the use of these type of nanostructures as a very promsing materials in applications such as optical coatings, SERS, and cancer cell hyperthermia. We proposed that the growth of these nanostructures can stem from a decrease in the reaction rate as temperature increases due to an enhanced copolymer hydrophobicity, which gives rise to a structure of interacting micelles formed from the fluid via a percolation transition (known as "soft gel") at elevated temperatures. In this way, reduction becomes slow enough to allow kinetic control of the reaction, and preferential adsorption of the copolymer molecules/micelles on certain crystallographic planes can favor the growth of certain nanocrystal facets to give the final structure. This alternative water-based system provides a more convenient and environmentally benign route to the synthesis of shape-controlled noble-metal nanocrystals in high yield because it does not involve toxic organic solvents or reagents and serves as a bridge between two frontline discipline: the block copolymeric science and anisotropic nanoparticles.     

Ethylenediamine-anchored gold nanoparticles on multi-walled carbon nanotubes: Synthesis and characterization

Binding of gold nanoparticles (Au-NP) at amine-functionalised multi-walled carbon nanotubes (MWNTs) is proposed. The MWNTs are functionalised with acylchloride groups, which further react with ethylenediamine to form amine-functionalised MWCNTs. These amines are able to bind preformed colloidal Au-NPs. The Au/MWNT composite material facilitates electron-transfer reactions with free-diffusing redox compounds.     

Synthesis, characterization, and self-assembly of protein lysozyme monolayer-stabilized gold nanoparticles

Lysozyme monolayer-protected gold nanoparticles (Au NPs) which are hydrophilic and biocompatible and show excellent colloidal stability (at low temperature, ca. 4 degrees C), were synthesized in aqueous medium by chemical reduction of HAuCl4 with NaBH4 in the presence of a familiar small enzyme, lysozyme. UV-vis spectra, transmission electron microscopy (TEM), atomic force microscopy, and X-ray photoelectron spectroscopy characterization of the as-prepared nanoparticles revealed the formation of well-dispersed Au NPs of ca. 2 nm diameter. Moreover, the color change of the Au NP solution as well as UV-vis spectroscopy and TEM measurements have also demonstrated the occurrence of Ostwald ripening of the nanoparticles at low temperature. Further characterization with Fourier transform infrared spectroscopy (FTIR) and dynamic light scattering indicated the formation of a monolayer of lysozyme molecules on the particle surface. FTIR data also indicated the intactness of the protein molecules coated on Au NPs. All the characterization results showed that the monodisperse Au NPs are well-coated directly with lysozyme. Driven by the dipole-dipole attraction, the protein-stabilized Au NPs self-assembled into network structures and nanowires upon aging under ambient temperature. On the basis of their excellent colloidal stability, controlled self-assembly ability, and biocompatible surface, the lysozyme monolayer-stabilized Au NPs hold great promise for being used in nanoscience and biomedical applications.     

Preparation and characterization of polyelectrolyte-coated gold nanoparticles

Gold nanoparticles of 5 nm diameter, stabilized by 4-(dimethylamino)pyridine (DMAP), were coated with poly(sodium 4-styrene sulfonate) (PSS) via electrostatic self-assembly. The suspension stability, monitored by the gold surface plasmon band (SPB), was studied by varying the pH, the PSS chain length, and PSS concentration. Enhanced stability is obtained at pH 10 (above the pKa of DMAP) when the polymer chain length matches or exceeds the particle circumference. Solid state 13C NMR was used to determine the presence of DMAP and polymers after subsequent deposition of weak and strong polycations: poly(allylamine hydrochloride) (PAH) and poly(diallyldimethylammonium chloride) (PDADMAC). At pH 10, DMAP remains associated with the nanoparticle after the first PSS layer has been formed. When PAH or PDADMAC are subsequently added at pH 4.5, DMAP is expelled, the suspensions remain stable, and zeta potential values indicate complete charge reversal. In the case of PDADMAC, however, the first layer of PSS is not fully retained. When PDADMAC is added at pH 10, DMAP and the first PSS layer are retained but lower zeta potentials and a higher SPB shift indicate a degraded stability. For PAH addition at pH 9.5, both DMAP and PSS are expelled and the suspension becomes unstable. These differences in stability of the multilayer components and the nanoparticle suspension are rationalized in terms of chain flexibility, polymer charge density, and the ability of the polymer functional groups to directly interact with the gold surface.     

Detection of telomerase activity in high concentration of cell lysates using primer-modified gold nanoparticles

Although the telomeric repeat amplification protocol (TRAP) has served as a powerful assay for detecting telomerase activity, its use has been significantly limited when performed directly in complex, interferant-laced samples. In this work, we report a modification of the TRAP assay that allows the detection of high-fidelity amplification of telomerase products directly from concentrated cell lysates. Briefly, we covalently attached 12 nm gold nanoparticles (AuNPs) to the telomere strand (TS) primer, which is used as a substrate for telomerase elongation. These TS-modified AuNPs significantly reduce polymerase chain reaction (PCR) artifacts (such as primer dimers) and improve the yield of amplified telomerase products relative to the traditional TRAP assay when amplification is performed in concentrated cell lysates. Specifically, because the TS-modified AuNPs eliminate most of the primer-dimer artifacts normally visible at the same position as the shortest amplified telomerase PCR product apparent on agarose gels, the AuNP-modified TRAP assay exhibits excellent sensitivity. Consequently, we observed a 10-fold increase in sensitivity for cancer cells diluted 1000-fold with somatic cells. It thus appears that the use of AuNP-modified primers significantly improves the sensitivity and specificity of the traditional TRAP assay and may be an effective method by which PCR can be performed directly in concentrated cell lysates.     

Synthesis and characterisation of surfactant-stabilised gold nanoparticles

Alkylthiol molecules, C₂₂H₄₅-SO₂-C₆H₄-O-C₄H₈-SH, HS-(CH₂)₂₁-OH and HS-(CH₂)₁₀-COOH, were used to stabilise gold clusters, formed in a two-phase system. The gold nanoparticles were investigated by using transmission electron microscopy, Fourier transform infra-red spectroscopy, ultraviolet-visible spectroscopy and X-ray photoelectron spectroscopy. The results show that surfactant-coated nanoparticles are indeed formed and the incorporation of a dipole or a terminal functionality into the surfactant does not hinder the self-assembling process.     

Synthesis and electrochemical applications of gold nanoparticles

This review covers recent advances in synthesis and electrochemical applications of gold nanoparticles (AuNPs). Described approaches include the synthesis of AuNPs via designing and choosing new protecting ligands; and applications in electrochemistry of AuNPs including AuNPs-based bioelectrochemical sensors, such as direct electrochemistry of redox-proteins, genosensors and immunosensors, and AuNPs as enhancing platform for electrocatalysis and electrochemical sensors.     

Synthesis and properties of tadpole-shaped gold nanoparticles

In this communication, gold nanoparticles with a tadpole shape were synthesized by a simple aqueous-phase chemical method. The unusual three-dimensional and crystallized structures were demonstrated by TEM, AFM, and HRTEM methods. The SEM and UV-visible absorption measurements and electrophoresis experiments revealed that the tadpoles had novel optical and electrical properties. These attractive structures and properties are expected to find uses in many fields such as electrics, optics, electrochemistry, and biological sensing.     

Synthesis of gold nanoparticles in niosomes

This work outlines a novel method for the synthesis of stable gold nanoparticles within the spatially confined region of vesicles. For the first time, Span/cholesterol based niosomes have been used for nanoparticle synthesis. The restricted geometry within niosomes prevents nanoparticle aggregation. The results have important implications for controlled delivery of nanoparticles for therapeutic applications.     

Synthesis and characterization of gold nanoparticles stabilized by palladium(II) phosphine thiol

This work is focused on the synthesis of innovative hybrids made by linking gold nanoparticles to protected organometallic Pd(II) thiolate. The organometallic protected Pd(II) thiolate, i.e. trans-thioacetate-ethynylphenyl-bis(tributylphosphine)palladium(II) has been synthesized, in situ deprotected and linked to Au nanoparticles. In this way new hybrid, with a direct link between Pd(II) and Au nanoparticles through a single S bridge, has been isolated. The combination of the organometallic Pd(II) thiol with gold nanoparticles allows the enhancement and tailoring of electronic and optical properties of the new organic-inorganic nano-compound. Single-crystal gold nanoparticles, uniform in shape and size were obtained by applying a modified two-phase method (improved Brust-Schiffrin reaction). In addition, the chemical environment of the Au nanoparticles was investigated and a covalent bonding between Au nanoparticles and the organometallic thiols was observed.     

Synthesis of nitric oxide-releasing gold nanoparticles

We report the synthesis of nitric oxide-releasing gold nanoparticles formed by place-exchange reaction of hexanethiol monolayer-protected clusters with diamine nitric oxide donor precursor molecules, which are subsequently converted to N-diazeniumdiolate NO donors. The nitric oxide release from the N-diazeniumdiolate-modified gold nanoparticles is tunable by varying the number and/or the chemical structure of the exchanged amine ligands. The size and stability of NO-releasing nanoparticles may prove useful for a range of biomedical and pharmaceutical applications.     

Synthesis of gold nanoparticles in organogels

1. Download : Download full-size image

     

Size-controlled synthesis and characterization of thiol-stabilized gold nanoparticles

Size-controlled synthesis of nanoparticles of less than a few nanometers in size is a challenge due to the spatial resolution limit of most scattering and imaging techniques used for their structural characterization. We present the self-consistent analysis of the extended x-ray absorption fine-structure (EXAFS) spectroscopy data of ligand-stabilized metal nanoclusters. Our method employs the coordination number truncation and the surface-tension models in order to measure the average diameter and analyze the structure of the nanoparticles. EXAFS analysis was performed on the two series of dodecanethiol-stabilized gold nanoparticles prepared by one-phase and two-phase syntheses where the only control parameter was the gold/thiol ratio xi, varied between 6:1 and 1:6. The two-phase synthesis resulted in the smaller particles whose size decreased monotonically and stabilized at 16 A when xi was lowered below 1:1. This behavior is consistent with the theoretically predicted thermodynamic limit obtained previously in the framework of the spherical drop model of Au nanoparticles.     

One-step synthesis and characterization of dendrimer-protected gold nanoparticles

We proposed an economic, convenient, and mild synthesis of dendrimer-protected gold nanoparticles by exposing a third-generation poly(propyleneimine) dendrimer-HAuCl₄ aqueous solution to sunlight without the additional step of introducing other reducing agents and protective agents. Most importantly, it is found that the size of the gold nanoparticles thus formed can be controlled by the molar ratio of the dendrimer to gold. The text was submitted by the author in English.     

Synthesis,characterization, and electrophoretic concentration of titanium dioxide nanoparticles in AOT microemulsions

Stable organosols of TiO₂ nanoparticles were prepared by hydrolysis of titanium tetraisopropoxide (TTIP) in microemulsions of sodium bis(2‐ethylhexyl)sulfoxynate (АОТ) in n‐decane with increasing the content of aqueous pseudophase from 0.15 to 0.85 vol.%. As the water content increased, the hydrodynamic diameter of nanoparticles grew from 10 to 225 nm, and the  ζ‐potential, from ‐6 to 18 mV (the surface of TiO₂ nanoparticles was recharged when the water content was 0.45 vol.%). Nonaqueous electrophoresis in a capacitor‐type cell made it possible to concentrate nanoparticles with a diameter of 60 to 225 nm (concentration factor was 10), separate 20 nm and 225 nm particles, and decrease the content of АОТ in organosol by an order of magnitude. Preparation of a concentrate of nanoparticles with a low content (0.015 M) of AOT included the following stages: (i) electrophoresis after synthesis; (ii) sampling of the concentrate and its twenty‐fold dilution with pure n‐decane; and (iii) repeated electrophoresis. In situ laser and spectrophotometric scanning of the interelectrode space showed the formation of a sharp boundary between the raffinate and the layer of moving nanoparticles during electrophoresis.     

Synthesis and characterization of magnetic nanoparticles

Magnetic nanoparticles with average diameter in the range of 6.4-8.3 nni have been synthesized by a chemical co-precipitation of Fe(Ⅱ)and Fe(Ⅲ)salts in 1.5 M NH4OH solution.The size of the magnetic particles is dependent on both temperature and the ionic strength of the iron ion solutions.The magnetic particles formed at higher temperature or lower ionic strength were slightly larger than those formed at lower temperature or higher ionic strength respectively.In spite of the different reaction conditions,all the resultant nanoparticles are nearly spherical and have a similar crystalline structure.At 300 K,such prepared nanoparticles are superparam-agnetic.The saturation magnetizations for 7.8 and 6.4 nm particles are 71 and 63 emu/g respectively,which are only ~ 20-30% less than the saturation magnetization(90 emu/g)of bulk Fe3O4 Our results indicated that a control of the reaction conditions could be used to tailor the size of magnetic nanoparticles in free precipitation.