Manipulation of the adsorption of ionic surfactants onto hydrophilic silica using polyelectrolytes

This paper demonstrates the use of polyelectrolytes to modify and manipulate the adsorption of ionic surfactants onto the hydrophilic surface of silica. We have demonstrated that the cationic polyelectrolyte poly(dimethyl diallylammonium chloride), poly-dmdaac, modifies the adsorption of cationic and anionic surfactants to the hydrophilic surface of silica. A thin robust polymer layer is adsorbed from a dilute polymer/surfactant solution. The resulting surface layer is cationic and changes the relative affinity of the cationic surfactant hexadecyl trimethylammonium bromide, C16TAB, and the anionic surfactant sodium dodecyl sulfate, SDS, to adsorb. The adsorption of C16TAB is dramatically reduced. In contrast, strong adsorption of SDS was observed, in situations where SDS would normally have a low affinity for the surface of silica. We have further shown that subsequent adsorption of the anionic polyelectrolyte sodium poly(styrene sulfonate), Na-PSS, onto the poly-dmdaac coated surface results in a change back to an anionic surface and a further change in the relative affinities of the cationic and anionic surfactants for the surface. The relative amounts of C16TAB and SDS adsorption depend on the coverage of the polyelectrolyte, and these preliminary measurements show that this can be manipulated.     

Polyelectrolyte modified solid surfaces: the consequences for ionic and mixed ionic/nonionic surfactant adsorption

This paper describes how the cationic polyelectrolyte, polyDMDAAC (poly(dimethyl diallylammonium chloride)), is used to manipulate the adsorption of the anionic surfactant SDS and the mixed ionic/nonionic surfactant mixture of SDS (sodium dodecyl sulfate)/C(12)E(6) (monododecyl hexaethylene glycol) onto the surface of hydrophilic silica. The deposition of a thin robust polymer layer from a dilute polymer/surfactant solution promotes SDS adsorption and substantially modifies the adsorption of SDS/C(12)E(6) mixtures in favor of a surface relatively rich in SDS compared to the solution composition. Different deposition conditions for the polyDMDAAC layer are discussed. In particular, at higher solution polymer concentrations and in the presence of 1 M NaCl, a thicker polymer layer is deposited and the reversibility of the surfactant adsorption is significantly altered.     

How electrolyte and polyelectrolyte affect the adsorption of the anionic surfactant SDS onto the surface of a cellulose thin film and the structure of the cellulose film. 1. Hydrophobic cellulose

The nature of hydrophobic thin cellulose films, formed by Langmuir-Blodgett (LB) deposition on silica, has been studied using neutron reflectivity (NR). The impact of electrolyte and a polyelectrolyte, poly(dimethyldiallylammonium chloride) (polydmdaac), on the adsorption of the anionic surfactant sodium dodecyl sulfate (SDS) onto the surface of the hydrophobic cellulose film and upon the structure of the cellulose film has been investigated. The results show how a combination of polyelectrolytes and electrolyte can be used to manipulate surfactant adsorption onto hydrophobic cellulose surfaces and modify the structure of the cellulose film by swelling and penetration. The results illustrate how polyelectrolytes can be used to reverse adsorption and swelling of cellulose films which are not reversible simply by dilution in solvent.     

Adsorption of cationic cellulose derivative/anionic surfactant complexes onto solid surfaces. II. Hydrophobized silica surfaces

The effect of the anionic surfactant SDS (sodium dodecyl sulfate) on the adsorption behavior of cationic hydroxyethyl cellulose (Polymer JR-400) and hydrophobically modified cationic cellulose (Quatrisoft LM-200) at hydrophobized silica has been investigated by null ellipsometry and compared with the previous data for adsorption onto hydrophilic silica surfaces. The adsorbed amount of LM-200 is found to be considerably larger than the adsorbed amount of JR-400 at both surfaces. Both polymers had higher affinity toward hydrophobized silica than to silica. The effect of SDS on polymer adsorption was studied under two different conditions: adsorption of polymer/SDS complexes from premixed solutions and addition of SDS to preadsorbed polymer layers. Association of the surfactant to the polymer seems to control the interfacial behavior, which depends on the surfactant concentration. For the JR-400/SDS complex, the adsorbed amount on hydrophobized silica started to increase progressively from much lower SDS concentrations, while the adsorbed amount on silica increased sharply only slightly below the phase separation region. For the LM-200/SDS complex, the adsorbed amounts increased progressively from very low SDS concentrations at both surfaces, and no large difference in the adsorption behavior was observed between two surfaces below the phase separation region. The complex desorbed from the surface at high SDS concentrations above the critical micelle concentration. The reversibility of the adsorption of polymer/SDS complexes upon rinsing was also investigated. When the premixed polymer/SDS solutions at high SDS concentrations (>5 mM) were diluted by adding water, the adsorbed amount increased due to the precipitation of the complex. The effect of the rinsing process on the adsorbed layer was determined by the hydrophobicity of the polymer and the surface.     

The role of electrolyte and polyelectrolyte on the adsorption of the anionic surfactant, sodium dodecylbenzenesulfonate, at the air-water interface

The role of the polyelectrolyte, poly(ethyleneimine), PEI, and the electrolytes NaCl and CaCl(2), on the adsorption of the anionic surfactant, sodium dodecylbenzenesulfonate, LAS, at the air-water interface have been investigated by neutron reflectivity and surface tension. The surface tension data for the PEI/LAS mixtures are substantially affected by pH and the addition of electrolyte, and are consistent with a strong adsorption of surface polymer/surfactant complexes down to relatively low surfactant concentrations. The effects are most pronounced at high pH, and this is confirmed by the adsorption data obtained directly from neutron reflectivity. However, the effects of the addition of PEI and electrolyte on the LAS adsorption are not as pronounced as previously reported for PEI/SDS mixtures. This is attributed primarily to the steric hindrance of the LAS phenyl group resulting in a reduction in the ion-dipole attraction between the LAS sulfonate and amine groups that dominates the interaction at high pH.     

Analytical investigation of the self-desorption of the oligomers of mixtures of a polydisperse ethoxylated surfactant with sodium dodecylsulfate from a silica/water interface

The adsorption isotherms onto a hydrophilic silica of mixtures of sodium dodecylsulfate (SDS) and of all the oligomers of a polydisperse nonylethylene glycol n-dodecyl ether (C(12)E(9)) surfactant were determined using a high-performance liquid chromatography (HPLC) technique. Incorporation of the anionic surfactant to the negatively charged silica surface is favored by the adsorption of the nonionic surfactant. Comparison between the adsorption isotherms of mixtures of SDS with a monodisperse C(12)E(9) and a polydisperse C(12)E(9) shows that the adsorption of SDS at the silica/water interface is stronger with the latter material than with the former in a large surface coverage domain. The composition of the surface aggregates and the variation of the oligomer distribution in these aggregates were determined. The previously described phenomena called self-desorption which was observed for the global C(12)E(9) and SDS surfactant mixtures was confirmed: increasing the total concentration at a fixed surfactant ratio induces at high concentration a desorption of the anionic surfactant and all of the less polar oligomers from the solid/water interface. An interpretation scheme is proposed which assumes that the interaction of SDS is larger with the less polar oligomers than with the polar ones. The self-desorption effect could then be considered as the consequence of the polydispersity of the nonionic surfactant and to the net repulsion interaction between SDS and the silica surface as the mole fraction of SDS in the surfactant mixture increases.     

Adsorption of polyelectrolyte/surfactant mixtures at the air-solution interface: poly(ethyleneimine)/sodium dodecyl sulfate

Neutron reflectivity and surface tension have been used to characterize the adsorption of the polyelectrolyte/ionic surfactant mixture of poly(ethyleneimine) (PEI) and sodium dodecyl sulfate (SDS) at the air-water interface. The surface tension behavior and adsorption patterns show a strong dependence upon the solution pH. However, the SDS adsorption at the interface is unexpectedly most pronounced when the pH is high (when the polymer is essentially a neutral polymer) and when the polymer architecture is branched rather than linear. For both the branched and the linear PEI polymer/surfactant complex formation results in a significant enhancement of the amount of SDS at the interface, down to surfactant concentrations approximately 10(-6) M. For the branched PEI a transition from a monolayer to a multilayer adsorption is observed, which depends on surfactant concentration and pH. In contrast, for the linear polymer, only monolayer adsorption is observed. This substantial increase in the surface activity of SDS by complexation with PEI results in spontaneous emulsification of hexadecane in water and the efficient wetting of hydrophobic substrates such as Teflon. In regions close to charge neutralization the multilayer adsorption is accentuated, and more extensively ordered structures, giving rise to Bragg peaks in the reflectivity data, are evident.     

Kinetics of the Formation of Nano-Sized Platinum Particles in Water-in-Oil Microemulsions

The association between low-charge-density polyelectrolytes adsorbed onto negatively charged surfaces (mica and silica) and an anionic surfactant, sodium dodecyl sulfate (SDS), has been investigated using surface force measurements, ellipsometry, and XPS. All three techniques show that the polyelectrolyte desorbs when the SDS concentration is high enough. The XPS study indicates that desorption starts at a SDS concentration of ca. 0.1 unit of cmc (8x10(-4) M) and that the desorption proceeds progressively as the SDS concentration is increased. Surface force measurements show that for the polyelectrolyte studied here, having 1% of the segments charged, the desorption proceeds without any swelling of the adsorbed layer. This behavior differs from that observed when polyelectrolytes of greater charge density are used. Copyright 2001 Academic Press.     

Interactions between chitosan and SDS at a low-charged silica substrate compared to interactions in the bulk--the effect of ionic strength

The effect of ionic strength on association between the cationic polysaccharide chitosan and the anionic surfactant sodium dodecyl sulfate, SDS, has been studied in bulk solution and at the solid/liquid interface. Bulk association was probed by turbidity, electrophoretic mobility, and surface tension measurements. The critical aggregation concentration, cac, and the saturation binding of surfactants were estimated from surface tension data. The number of associated SDS molecules per chitosan segment exceeded one at both salt concentrations. As a result, a net charge reversal of the polymer-surfactant complexes was observed, between 1.0 and 1.5 mM SDS, independent of ionic strength. Phase separation occurs in the SDS concentration region where low charge density complexes form, whereas at high surfactant concentrations (up to several multiples of cmc SDS) soluble aggregates are formed. Ellipsometry and QCM-D were employed to follow adsorption of chitosan onto low-charged silica substrates, and the interactions between SDS and preadsorbed chitosan layers. A thin (0.5 nm) and rigid chitosan layer was formed when adsorbed from a 0.1 mM NaNO3 solution, whereas thicker (2 nm) chitosan layers with higher dissipation/unit mass were formed from solutions at and above 30 mM NaNO3. The fraction of solvent in the chitosan layers was high independent of the layer thickness and rigidity and ionic strength. In 30 mM NaNO3 solution, addition of SDS induced a collapse at low concentrations, while at higher SDS concentrations the viscoelastic character of the layer was recovered. Maximum adsorbed mass (chitosan + SDS) was reached at 0.8 times the cmc of SDS, after which surfactant-induced polymer desorption occurred. In 0.1 mM NaNO3, the initial collapse was negligible and further addition of surfactant lead to the formation of a nonrigid, viscoelastic polymer layer until desorption began above a surfactant concentration of 0.4 times the cmc of SDS.     

Effect of polyelectrolytes and polyelectrolyte mixtures on the electrokinetic potential of dispersed particles. 2. Electrokinetic potential of silica particles in electrolyte, polyelectrolyte and polyelectrolyte mixtures solutions

The effect pH, ionic strength (KCl concentration), weakly and medium charged anionic and cationic polyelectrolytes (PEs) as well as their binary mixtures on the electrokinetic potential of silica particles as a function of the polyelectrolyte/mixture dose, its composition, charge density (CD) of the PE, and way of adding the polymers to the suspension has been studied. It has been shown that addition of increasing amount of anionic PEs increases the absolute value of the negative zeta-potential of particles at pH > pH isoelectric point (IEP = 2.5); this increase is stronger the charge density of the polyelectrolyte is higher. Adsorption of cationic polyelectrolytes at these pH values gives a significant decrease in the negative ζ-potential and overcharging the particles; changes in the ζ-potential are more pronounced for PE samples with higher CD. In mixtures of cationic and anionic PE at pH > pHIEP, the ζ-potential of particles is determined by the adsorbed amount of the anionic polymer independently of the CD of PEs, the mixture composition and the sequence of addition of the mixture components. Unexpectedly, the ζ-potential of silica at pH = 2.1, i.e. < pHIEP, turned out to be positive in the presence of both anionic PE and cationic + anionic PE mixtures. This is explained by formation (and adsorption onto positively charged silica surface) of pseudo-cationic PEs from anionic ones due to transfer of protons from the solution to the amino-group of the anionic polymer. Considerations about the role of coulombic and non-coulombic forces in the mechanism of PE adsorption are presented.     

Influence of the polyelectrolyte poly(ethyleneimine) on the adsorption of surfactant mixtures of sodium dodecyl sulfate and monododecyl hexaethylene glycol at the air-solution interface

The polyelectrolyte poly(ethylenenimine), PEI, is shown to strongly influence the adsorption of the anionic-nonionic surfactant mixture of sodium dodecyl sulfate, SDS, and monododecyl hexaethylene glycol, C(12)E(6), at the air-solution interface. In the presence of PEI, the partitioning of the mixed surfactants to the interface is highly pH-dependent. The adsorption is more strongly biased to the SDS as the pH increases, as the PEI becomes a weaker polyelectrolyte. At surfactant concentrations >10(-4) M, the strong interaction and adsorption result in multilayer formation at the interface, and this covers a more extensive range of surfactant concentrations at higher pH values. The results are consistent with a strong interaction between SDS and PEI at the surface that is not predominantly electrostatic in origin. It provides an attractive route to selectively manipulate the adsorption and composition of surfactant mixtures at interfaces.     

The structures of complexes between polyethylene imine and sodium dodecyl sulfate in D2O: a scattering study

The association between a highly branched polyelectrolyte with ionizable groups, polyethylene imine (PEI), and an anionic surfactant, sodium dodecyl sulfate (SDS), has been investigated at two pH values, using small-angle neutron and light scattering. The scattering data allow us to obtain a detailed picture of the association structures formed. Small-angle neutron scattering (SANS) measurements in solutions containing highly charged PEI at low pH and low SDS concentrations indicate the presence of disklike aggregates. The aggregates change to a more complex three-dimensional structure with increasing surfactant concentration. One pronounced feature in the scattering curves is the presence of a Bragg-like peak at high q-values observed at a surfactant concentration of 4.2 mM and above. This scattering feature is attributed to the formation of a common well-ordered PEI/SDS structure, in analogue to what has been reported for other polyelectrolyte-surfactant systems. Precipitation occurred at the charge neutralization point, and X-ray diffraction measurements on the precipitate confirmed the existence of an ordered structure within the PEI/SDS aggregates, which was identified as a lamellar internal organization. Polyethylene imine has a low charge density in alkaline solutions. At pH 10.1 and under conditions where the surfactant was contrast matched, the SANS scattering curves showed only small changes with increasing surfactant concentration. This suggests that the polymer acts as a template onto which the surfactant molecules aggregate. Data from both static light scattering and SANS recorded under conditions where SDS and to a lower degree PEI contribute to the scattering were found to be consistent with a structure of stacked elliptic bilayers. These structures increased in size and became more compact as the surfactant concentration was increased up to the charge neutralization point.     

Binding of sodium dodecyl sulfate with linear and branched polyethyleneimines in aqueous solution at different pH values

Isothermal titration microcalorimetry (ITC), conductivity, and turbidity measurements have been carried out to study the interaction of sodium dodecyl sulfate (SDS) with polyethyleneimines (PEI) including linear PEI and branched PEI at different pH values of 3, 7, and 10. In all cases, the polymers show a remarkable affinity toward SDS. At pH 3, the polymer PEI is a strong polycation, and the binding is dominated by electrostatic 1:1 charge neutralization with the anionic surfactant. At pH 7, the electrostatic attraction between SDS and PEI is weak, and the hydrophobic interaction becomes stronger. At the natural pH of 10, PEI is essentially nonionic and binds SDS in the form of polymer-bound surfactant aggregates. The charge neutralization concentration (C1) of SDS for the PEI-SDS complex can be derived from the curves of variation of the enthalpy, conductivity, and turbidity with SDS concentration. There is good agreement between the results from the three methods and all show a decrease with increasing pH. The total interaction enthalpies (deltaH(total)) of PEI with SDS are obtained from the observed enthalpy curves and the difference enthalpy (deltaH*) between the total enthalpy of branched PEI with SDS, and the total enthalpy of linear PEI with SDS can be derived from the obtained deltaH(total). The difference deltaH* increases dramatically as pH increases, which indicates that the interactions are different for linear PEI and branched PEI at high pH values. A schematic map of the different states of aggregation is presented.     

The effects of the addition of the polyelectrolyte, poly(ethyleneimine), on the adsorption of mixed surfactants of sodium dodecylsulfate and dodecyldimethylaminoacetate at the air-water interface

The effects of the addition of the polyelectrolyte, poly(ethyleneimine), PEI, on the adsorption of the mixed surfactants of sodium dodecylsulfate, SDS, and dodecyldimethylaminoacetate, dodecyl betaine, at the air-water interface have been investigated using neutron reflectivity and surface tension. In the absence of PEI the SDS and dodecyl betaine surfactants strongly interact and exhibit synergistic adsorption at the air-water interface. The addition of PEI, at pH 7 and 10, results in a significant modification of the surface partitioning of the SDS/dodecyl betaine mixture. The strong surface interaction at high pH (pH 7 and 10) between the PEI and SDS dominates the surface behavior. For solution compositions in the range 20/80-80/20 mol ratio dodecyl betaine/SDS at pH 7 the surface composition is strongly biased towards the SDS. At pH 10 a similar behavior is observed for a solution composition of 50/50 mol ratio dodecyl betaine/SDS. This strong partitioning in favor of the SDS at high pH is attributed to the strong ion-dipole attraction between the SDS sulfate and the PEI imine groups. At pH 3, where the electrostatic interactions between the surfactant and the PEI are dominant, the dodecyl betaine more effectively competes with the SDS for the interface, and the surface composition is much closer to the solution composition.     

Adsorption behavior of hydrophobin and hydrophobin/surfactant mixtures at the solid-solution interface

The adsorption of surface-active protein hydrophobin, HFBII, and HFBII/surfactant mixtures at the solid-solution interface has been studied by neutron reflectivity, NR. At the hydrophilic silicon surface, HFBII adsorbs reversibly in the form of a bilayer at the interface. HFBII adsorption dominates the coadsorption of HFBII with cationic and anionic surfactants hexadecyltrimethyl ammonium bromide, CTAB, and sodium dodecyl sulfate, SDS, at concentrations below the critical micellar concentration, cmc, of conventional cosurfactants. For surfactant concentrations above the cmc, HFBII/surfactant solution complex formation dominates and there is little HFBII adsorption. Above the cmc, CTAB replaces HFBII at the interface, but for SDS, there is no affinity for the anionic silicon surface hence there is no resultant adsorption. HFBII adsorbs onto a hydrophobic surface (established by an octadecyl trimethyl silane, OTS, layer on silicon) irreversibly as a monolayer, similar to what is observed at the air-water interface but with a different orientation at the interface. Below the cmc, SDS and CTAB have little impact upon the adsorbed layer of HFBII. For concentrations above the cmc, conventional surfactants (CTAB and SDS) displace most of the HFBII at the interface. For nonionic surfactant C(12)E(6), the pattern of adsorption is slightly different, and although some coadsorption at the interface takes place, C(12)E(6) has little impact on the HFBII adsorption.     

Deuterium isotope effects on the interaction between hyperbranched polyethylene imine and an anionic surfactant

Solvent isotope effects on the interaction between the hyperbranched cationic polyelectrolyte, polyethylene imine (PEI), and the anionic surfactant sodium dodecyl sulfate (SDS) were investigated using potentiometric titration and eletrophoretic mobility measurements. In the basic pH range, a significantly higher fraction of the amine groups was found to be protonated when the PEI was dissolved in D2O compared to H2O at the same pH/pD. The difference in polymer charge in the two solvents decreases gradually with decreasing pH, and it completely diminishes at around pH = 4. Electrophoretic mobility measurements of PEI/SDS complexes at different pH values correlated very well with these observations. At pH/pD approximately 9 a much higher mobility of the PEI/SDS complexes was found in D2O than in H2O at low surfactant concentrations, and the charge neutralization point shifted to a considerably larger surfactant concentration in heavy water. These results can be explained by the significantly higher charge density of the PEI in D2O compared to H2O. However, at the natural pH/pD as well as at pH = 4 and pD = 4 conditions the PEI molecules have roughly equal charge densities, which result in very similar charged characteristics (mobilities) of the PEI/SDS complexes as well as the same charge neutralization SDS concentration. It can be concluded that extreme care must be taken in the general analysis of those experiments in which weak polyelectrolyte/surfactant aggregates are investigated in heavy water, and then these observations are correlated with structures of the same system in water.     

Silica nanoparticles at interfaces modulated by amphiphilic polymer and surfactant

The interfacial behavior of silica nanoparticles in the presence of an amphiphilic polymer poly( N-isopropylacrylamide) (PNIPAM) and an anionic surfactant sodium dodecyl sulfate (SDS) is studied using neutron reflectivity. While the nanoparticles do not show any attraction to hydrophilic and hydrophobic surfaces in pure water, presence of the amphiphilic polymer induces significant adsorption of the nanoparticles at the hydrophobic surface. This interfacial behavior is activated due to interaction of the nanoparticles with PNIPAM, the amphiphilic nature of which leads to strong adsorption at a hydrophobic surface but only weak interaction with a hydrophilic surface. The presence of SDS competes with nanoparticle-PNIPAM interaction and in turn modulates the interfacial properties of the nanoparticles. These adsorption results are discussed in relation to nanoparticle organization templated by dewetting of charged polymer solutions on a solid substrate. Our previous studies showed that nanoparticle assembly can be induced to form complex morphologies produced by dewetting of the polymer solutions, such as a polygonal network and long-chain structures. This approach, however, works on a hydrophilic substrate but not on a hydrophobic substrate. These observations can be explained in part by particle-substrate interactions revealed in the present study.     

Surfactant adsorption onto cellulose surfaces

The adsorption of the cationic surfactant, hexadecyl trimethyl ammonium bromide, C16TAB, onto model cellulose surfaces, prepared by Langmuir-Blodgett deposition as thin films, has been investigated by neutron reflectivity. Comparison between the adsorption of C16TAB onto hydrophilic silica, a hydrophobic cellulose surface, and a regenerated (hydrophilic) cellulose surface is made. Adsorption onto the hydrophilic silica and onto the hydrophilic cellulose surfaces is similar, and is in the form of surface aggregates. In contrast, the adsorption onto the hydrophobic cellulose surface is lower and in the form of a monolayer. The impact of the surfactant adsorption and the in situ surface regeneration on the structure of the cellulose thin films and the nature of solvent penetration into the cellulose films are also investigated. For the hydrophobic cellulose surface, intermixing between the cellulose and surfactant occurs, whereas there is little penetration of surfactant into the hydrophilic cellulose surface. Measurements show that solvent exchange between the partially hydrated cellulose film and the solution is slow on the time scale of the measurements.     

Interaction of the anionic surfactant SDS with a cellulose thin film and the role of electrolyte and poyelectrolyte. 2 Hydrophilic cellulose

The interaction of the anionic surfactant, sodium dodecylsulfate (SDS), with the hydrophilic surface of a thin cellulose film and the role of electrolyte (0.1 M NaCl) and the polyelectrolyte, poly(dimethyldiallyl ammonium chloride) [polydmdaac], have been studied by neutron reflectivity (NR). The thin cellulose films were prepared by Langmuir-Blodgett (LB) deposition of trimethylsilyl-cellulose (TMSC) on silicon, and the hydrophilic surface was produced by the cleaving of the terminal methyl groups of the TMSC by HCl vapor. Despite both the surfactant and cellulose surfaces being nominally anionic, SDS adsorption and swelling of the cellulose film occurred during adsorption. The results show that the nature of the adsorption and the extent of the penetration into the cellulose film can be controlled by the addition of electrolyte, NaCl, and cationic polyelectrolyte, polydmdaac.     

Coadsorption of sodium dodecyl sulfate and a polyanion onto poly(ethylenimine) in multilayered thin films

Mixed surfactant-polyelectrolyte multilayer films were fabricated by both ionic self-assembly and spin assembly. A polycation [PEI = poly(ethylenimine)] was deposited from a dilute solution, while a polyanion (PAZO = poly[1-[4-(3-carboxy-4-hydroxyphenylazo) benzenesulfonamido]-1,2-ethanediyl, sodium salt]) was deposited from a mixture containing a fixed concentration of polyanion and various concentrations of the anionic surfactant sodium dodecyl sulfate (SDS). Coadsorption of SDS and PAZO onto PEI layers was observed using both deposition methods and attributed to strong PEI-SDS interactions and entropic factors. Increasing the concentration of SDS resulted in films containing progressively less adsorbed PAZO. No further reduction in the amount of adsorbed PAZO was observed above the SDS critical micelle concentration. We attribute the film growth behavior to a fast adsorption of SDS onto PEI, followed by a slower adsorption of PAZO onto the remaining unoccupied binding sites. We observe that SDS interpenetrates throughout the PAZO and PEI layers, increasing the surface hydrophobicity of both. We observed similar behavior for both ionically self-assembled and spin-assembled systems.