Surface core-level shift of Pd at the AgcPd1−c(1 1 1) surface: Nonlinear subsurface effects

The surface core-level binding-energy shift (SCLS) of Pd at the Ag_cPd_1−c(1 1 1) surface is calculated as a function of bulk concentration of the alloy. The equilibrium volume and the surface concentration profile used in the calculations refer to the 0 K case. The SCLSs are evaluated within the Z + 1 approximation. The results are analysed using the mixing enthalpy of the alloy and the bulk and surface chemical potentials. A relation of the SCLS to the bulk concentration is considered. This relation is shown to be mediated by the surface concentration profile which induces the observed nonlinear behaviour. The results are interpreted using a simple model for the alloy electronic structure.     

Spatio-temporal dynamics of the NO + NH3 reaction on polycrystalline platinum

Spontaneous reaction rate oscillations and spatio-temporal patterns have been observed by mass spectrometry and photoemission electron microscopy (PEEM) during the reduction of NO by NH₃ on polycrystalline platinum at 1 × 10⁻⁴ Torr and temperatures from 460-520 K. The appearance of both oscillations and patterns was found to be strongly dependent on the gas phase composition and the temperature. In addition, the overall dynamics of the catalyst were found to be dominated by the nonlinear behavior of Pt(1 0 0) type grains, while other types of grains did not participate. In contrast to previous studies, a large number of complex multimodal oscillations were observed, particularly as the coupling between the surface and the gas phase was increased. The appearance of these complex oscillations demonstrates the importance of gas phase coupling to understanding catalytic reactions, even in high vacuum systems.     

Chloromethane surface chemistry on Fe3O4(1 1 1)-(2 × 2): A thermal desorption spectrometry comparison of CCl4, CBr2Cl2, and CH2Cl2

The surface chemistry of CBr₂Cl₂ on the Fe₃O₄(1 1 1)-(2 × 2) selvedge of single-crystal α-Fe₂O₃(0 0 0 1) has been investigated using temperature programmed reaction and desorption (TPR/D) measurements. The spectra obtained in this case show that strong chemisorption occurs and that a series of adsorbed halogenated reaction products are present. By comparison, studies of the adsorbed phase of CH₂Cl₂ show that only physisorption occurs. The TPR/D spectra of CBr₂Cl₂ show that dissociative formation of CCl₂ followed by its reaction with lattice oxygen is central to the monolayer reaction chemistry in this chloromethane. The branching ratios of the various desorbed products are compared with those obtained from CCl₄ adsorbed on the same (2 × 2) surface.     

The interactions of thiophene with polycrystalline UO2

We have studied the adsorption and desorption of thiophene on polycrystalline UO₂ as function of coverage, over the temperature range 100-640 K, using X-ray photoelectron spectroscopy (XPS), temperature programmed desorption (TPD) and electron stimulated desorption (ESD). Thiophene is found to adsorb molecularly on stoichiometric UO₂. C 1s and S 2p XPS spectra are measured at different thiophene exposures and at different temperatures; they show no evidence for the presence of dissociation fragments, confirming that thiophene adsorbs and desorbs molecularly on a polycrystalline stoichiometric UO₂ surface. The variation of the S 2p and C 1s intensity as function of exposure, together with ESD measurements of O⁺ as function of exposure, can be connected to the growth mode of a thiophene film on UO₂; the thiophene film converts from a flat-lying configuration to an inclined structure as coverage increases. The effects of X-rays, UV, and electron irradiation on thiophene films have been studied in two different coverage regimes, monolayer and multilayer. Irradiation leads to a modification of thiophene films, and appreciable concentrations of species stable to 640 K are present on the surface for both regimes. The XPS results suggest that irradiation induces polymerization and oligomerization, as well as formation of thiolates and dissociation fragments of thiophene. The adsorption and reactivity of thiophene on defective UO₂ surfaces have also been studied. The O vacancies and defects in the oxide surface cause cleavage of C-H and C-S bonds leading to the dissociation of thiophene at temperatures as low as 100 K. These results illustrate the important role played by O vacancies in the chemistry of thiophene over an oxide surface.     

Interaction of O2 with Pd single crystals in the range 1-150 Torr: Surface morphology transformations

The interaction of O₂ with Pd single crystals including Pd(1 1 1), Pd(1 1 0) and Pd(1 0 0) in the pressure range 1-150 Torr was studied using scanning tunneling microscopy (STM). The Pd single crystal surface morphologies were determined by the oxidation conditions: O₂ pressure, exposure time and treatment temperature. Oxygen dissolution into Pd metal followed by the formation of bulk oxide was observed. The dissolution of oxygen resulted in the increase of the inter-planar spacing between the first two layers, 9-14% increase after an exposure of Pd(1 1 1) to 10-25 Torr O₂ at 600 K for 10 min, and 10-20% increase after exposing Pd(1 1 0) and Pd(1 0 0) to 1 Torr O₂ at 600 K for 10 min. Elongated or semi-spherical oxide agglomerates along the steps nucleated and grew on both Pd(1 1 0) and Pd(1 0 0) surfaces after oxidation in 5-25 Torr O₂ at 600 K. When bulk PdO was formed, the single crystal surface was covered with semi-spherical agglomerates 2-4 nm in size, which tended to aggregate to form a “cauliflower-like” structure. The single crystal surface area also increased during oxidation.     

Spatially resolved dynamics of the TiO2(1 1 0) surface reconstruction

We use low-energy electron microscopy to image the reversible transformation of the TiO₂(1 1 0) surface between a high-temperature 1 × 1 structure and a low-temperature 1 × 2 structure. The reconstruction dynamics are novel: 1 × 2 bands nucleated during cooling at the steps of the starting 1 × 1 surface and then grew laterally from the steps. The transformation kinetics are dominated by mass flow from the surface to the bulk, a process that facilitates converting the high-density 1 × 1 phase to the lower-density 1 × 2 phase. We have also imaged how the 1 × 1 surface reconstructs to 1 × 2 phase after sufficient oxygen is removed from the crystal’s bulk during vacuum annealing. 1 × 2 bands also nucleated and grew laterally from the initial 1 × 1-surface’s steps. However, because this isothermal 1 × 1-to-1 × 2 transition occurs largely by mass redistribution on the surface, the steps of the initial 1 × 1 surface and final 1 × 2 surface are offset. We propose models of mass redistribution during the 1 × 1/1 × 2 phase transition to explain this effect. We conclude that the phase transition is first-order because it always occurred by the nucleation and growth of discrete phases. Finally, we show that quenching can roughen TiO₂’s surface by forming pits and that changing temperature causes step motion on 1 × 2 surfaces.     

One-dimensional structural and electronic properties of magnetite Fe3O4(1 1 0)

We study the structure and the electronic properties of the (1 1 0) surfaces of magnetite Fe₃O₄ thin films by scanning tunneling microscopy (STM) and spectroscopy (STS). The STM images show a surface reconstruction consisting of ridges along the direction. Based on atomically resolved STM images we present a model for the observed ridge reconstruction of the surface, in agreement with a bulk-truncated layer containing both octahedral and tetrahedral iron ions. The metallic and semiconductor-like shapes of the measured current-voltage (I-V) curves indicate a non-uniform segregation of magnesium through the film. The weak contrast between the tops and valleys of ridges measured in the STS current maps is attributed to tetrahedral and octahedral coordination at the tops and the valleys, respectively. This attribution is in agreement with the proposed structure model. We observe a contrast enhancement at a tip change accompanied by a corrugation enhancement. This tip change is induced by picking up material from the sample, resulting in a magnetic tip. Thus, the contrast enhancement is attributed to detection of spin polarized current.     

Defects and Pd growth on the reduced SnO2(1 0 0) surface

Scanning tunneling microscopy experiments on a clean, reduced SnO₂(1 0 0)-(1 × 1) surface reveal surface defects with zero-, one-, and two-dimensions. Point defects consist of missing SnO/SnO₂ units. Line defects are probably crystallographic shear planes that extend to the surface and manifest themselves as rows of atoms, shifted half a unit cell along the [0 1 0] direction. Their ends act as preferential nucleation sites for the formation of Pd clusters upon vapor deposition. Areas of a more reduced surface phase, still with a (1 × 1) structure and a half-unit cell deep, form at [0 0 1]-oriented step edges.     

The thermal spreading of antimony oxides onto Fe2O3

The uniform antimony-rich surface layer on Fe₂O₃ was carried out via thermal spreading of Sb₂O₃ and Sb₂O₄. TG–DTA results indicate that the oxidation temperature of Sb₂O₃ was decreased ca. 100 K due to thermal spreading effect. Although Sb₂O₄ is almost catalytically inert for oxidation of isobutane and Fe₂O₃ is a typical non-selective catalyst for this reaction, the formation of antimony-rich layer suppresses the combustion reactions and favors the partial oxidation reactions. When Sb₂O₄ instead of Sb₂O₃ was used as antimony resource, the enrichment of antimony on Fe₂O₃ surface was much lower. However, the reaction atmosphere of isobutane oxidation enhances antimony spreading over Fe₂O₃ surface. According to Mars–Van Krevelen mechanism, some Sb₂O₄ in catalysts could be intermediately reduced into Sb₂O₃ during reaction of isobutene oxidation, which thermal spreading is much easier. As shown by Raman results, the Sb₂O₄ that has been spread on Fe₂O₃ surface is probably amorphous.     

The Fe3O4 origin of the “Biphase” reconstruction on α-Fe2O3(0 0 0 1)

The so-called Biphase termination on α-Fe₂O₃ has been widely accepted to be a structure with a 40 Å unit supercell composed of coexisting islands of Fe_1−xO and α-Fe₂O₃. Based on thermodynamic arguments and experimental evidence, including transmission electron diffraction, imaging, magnetic and spectroscopic information, it is found that the previously proposed structure model is inaccurate. The actual Biphase structure is instead a layered structure related to the reduction of α-Fe₂O₃ to Fe₃O₄. A model for the Biphase termination is proposed which does not contain islands of Fe_1−xO but instead consists of bulk α-Fe₂O₃ and a Fe₃O₄-derived overlayer. The proposed model is consistent with all current and previously reported experimental findings.     

The surface structure of Fe3O4(1 1 1) films as studied by CO adsorption

We have studied adsorption of CO on Fe₃O₄(1 1 1) films grown on a Pt(1 1 1) substrate by temperature programmed desorption (TPD), infrared reflection absorption spectroscopy (IRAS) and high resolution electron energy loss spectroscopy (HREELS). Three adsorption states are observed, from which CO desorbs at ∼110, 180, and 230 K. CO adsorbed in these states exhibits stretching frequencies at ∼2115-2140, 2080 and 2207 cm⁻¹, respectively. The adsorption results are discussed in terms of different structural models previously reported. We suggest that the Fe₃O₄(1 1 1) surface is terminated by 1/2 ML of iron, with an outermost 1/4 ML consisting of octahedral Fe²⁺ cations situated above an 1/4 ML of tetrahedral Fe³⁺ ions, in agreement with previous theoretical calculations. The most strongly bound CO is assigned to adsorption to Fe³⁺ cations present on the step edges.     

A structural study of a C3H3 species coadsorbed with CO on Pd(1 1 1)

The combination of chemical-state-specific C 1s scanned-energy mode photoelectron diffraction (PhD) and O K-edge near-edge X-ray absorption fine structure (NEXAFS) has been used to determine the local adsorption geometry of the coadsorbed C₃H₃ and CO species formed on Pd(1 1 1) by dissociation of molecular furan. CO is found to adopt the same geometry as in the Pd(1 1 1)c(4 × 2)-CO phase, occupying the two inequivalent three-fold coordinated hollow sites with the C–O axis perpendicular to the surface. C₃H₃ is found to lie with its molecular plane almost parallel to the surface, most probably with the two ‘outer’ C atoms in equivalent off-atop sites, although the PhD analysis formally fails to distinguish between two distinct local adsorption sites.     

A Monte Carlo study of the thermal properties of Cu3Au low index surfaces

The thermal dependencies of composition and order of the (111), (100) and (110) Cu₃Au surfaces are studied at the atomic scale by means of Monte Carlo simulations in the “transmutational” ensemble at constant volume. The question addressed is the extent to which such simulations carried on with a model N-body potential designed on the basis of bulk energetic and mechanical properties allow predictions consistent with experimental observations of the surface. Although the currently available experimental data still leave unanswered questions, many of them allow for comparison with modelling. Qualitative agreement is found for temperature dependencies of both surface composition and order, and the simulation results are discussed in detail. Some clear discrepancies are found as well, in particular (but not only) in the case of the (110) surface and its first neighbouring layer. Although the origin of such differences is not yet clear, it is suggested that they may serve to assess and to improve the model in the light of quantitative surface studies.     

Interaction of O2 with Pd single crystals in the range 1-150 Torr: Oxygen dissolution and reaction

The interaction of O₂ with Pd(1 1 1), Pd(1 1 0) and Pd(1 0 0) was studied in the pressure range 1-150 Torr by the techniques of temperature programmed decomposition (TPD), Auger electron spectroscopy (AES) and low energy electron diffraction (LEED). The oxidation of Pd was rate-determined by oxygen diffusion into Pd metal followed by the diffusion into PdO once the bulk oxide layer was formed. The dissolution of oxygen atoms into Pd metal followed the Mott-Cabrera model with diffusion coefficient 10⁻¹⁶ cm² s⁻¹ at 600 K and activation energy of 60-85 kJ mol⁻¹. The bulk oxide phase was formed when a critical oxygen concentration was reached in the near-surface region. The formation of PdO was characterized by a decrease in the oxygen uptake rate, the complete fading of the metallic Pd LEED pattern and an atomic ratio O/Pd of 0.15-0.7 as measured by AES. The diffusion of oxygen through the bulk oxide layer again conformed to the Mott-Cabrera parabolic diffusion law with diffusion coefficient 10⁻¹⁸ cm² s⁻¹ at 600 K and activation energy of 111-116 kJ mol⁻¹. The values for the diffusion coefficient and apparent activation energy increased as the surface atom density of the single crystals increased.     

Dual surface coil with high-B1 homogeneity for deep organ MR imaging

The theory and construction of a dual surface coil which provides good B₁ homogeneity and sensitivity in a defined volume of interest is described. The probe comprises two coaxial rings, of different diameters and in different planes, which carry opposing currents of different values. Current in the second ring compensates for the roll-off of the B₁ field associated with a single surface coil. Coupling between the rings and a third matching ring is by mutual inductance only. A comparison to a traditional surface coil with practical application to pig brain imaging at a field strength of 7 Tesla is shown.     

Structure and composition of the NiPd(1 1 0) surface

The NiPd(1 1 0) alloy surface was studied using low energy electron diffraction to measure the structure and composition of the first three atomic layers. The surface layer is highly enriched in Pd and has a significantly buckled structure. The second layer is also buckled, with displacements even larger than the surface layer. The second layer also exhibits intralayer segregation (chemical ordering), with alternate close-packed rows of atoms being Ni enriched and Pd enriched. The third layer has a structure and composition close to that of the bulk alloy. These results are compared with results for the other low index faces of NiPd, the extensive literature on NiPt alloy surfaces, and the growing body of theoretical literature for NiPd alloy surfaces.     

A study on magnetoelastic properties of Tb3 (Fe28−xCox) V1.0 (x=0, 3, 6) compounds

In this work, The magnetoelastic properties of polycrystalline samples of Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) intermetallic compounds are investigated by means of linear thermal expansion and magnetostriction measurements in the temperature range of 77–515 K under applied magnetic fields up to 1.5 T. The linear thermal expansion increases with the Co content. The well-defined anomalies observed in the linear thermal expansion coefficients for Tb₃ (Fe_28−xCo_x) V_1.0 (x=0, 3, 6) compounds are associated with the magnetic ordering temperature for x=0 and spin reorientation temperatures for x=3, 6. Below transition temperatures, the value of the longitudinal magnetostriction (λ_Pa) at 1.6 T increases with Co content.     

In situ XPS study of Pd(1 1 1) oxidation. Part 1: 2D oxide formation in 10 mbar O2

The oxidation of the Pd(1 1 1) surface was studied by in situ XPS during heating and cooling in 3 × 10⁻³ mbar O₂. A number of adsorbed/dissolved oxygen species were identified by in situ XPS, such as the two dimensional surface oxide (Pd₅O₄), the supersaturated O_ads layer, dissolved oxygen and the R 12.2° surface structure.Exposure of the Pd(1 1 1) single crystal to 3 × 10⁻³ mbar O₂ at 425 K led to formation of the 2D oxide phase, which was in equilibrium with a supersaturated O_ads layer. The supersaturated O_ads layer was characterized by the O 1s core level peak at 530.37 eV. The 2D oxide, Pd₅O₄, was characterized by two O 1s components at 528.92 eV and 529.52 eV and by two oxygen-induced Pd 3d_5/2 components at 335.5 eV and 336.24 eV. During heating in 3 × 10⁻³ mbar O₂ the supersaturated O_ads layer disappeared whereas the fraction of the surface covered with the 2D oxide grew. The surface was completely covered with the 2D oxide between 600 K and 655 K. Depth profiling by photon energy variation confirmed the surface nature of the 2D oxide. The 2D oxide decomposed completely above 717 K. Diffusion of oxygen in the palladium bulk occurred at these temperatures. A substantial oxygen signal assigned to the dissolved species was detected even at 923 K. The dissolved oxygen was characterised by the O 1s core level peak at 528.98 eV. The “bulk” nature of the dissolved oxygen species was verified by depth profiling.During cooling in 3 × 10⁻³ mbar O₂, the oxidised Pd²⁺ species appeared at 788 K whereas the 2D oxide decomposed at 717 K during heating. The surface oxidised states exhibited an inverse hysteresis. The oxidised palladium state observed during cooling was assigned to a new oxide phase, probably the R 12.2° structure.     

Core-level spectroscopy of the Pd/W(1 1 0) interface: Evidence of long-range Pd-island-W interactions at submonolayer Pd coverages

We have measured W 4f_7/2 core-level photoemission spectra from W(1 1 0) in the presence of Pd overlayers for coverages up to ∼1 pseudomorphic monolayer (ML). At coverages close to 0.05 ML a striking change in the W core-level spectrum is observed, which we interpret as indicating a long-range lateral effect of 2D Pd islands upon the W electronic structure in both the first and second W layers. As the coverage increases the long-range effect weakens and finally vanishes near 0.85 ML. Above this coverage the W spectra are typical for a W-based bimetallic interface, with the first-layer W atoms exhibiting a small interfacial core-level shift (−95 ± 5 meV) compared to the bulk atoms.     

Inhibition of initial surface oxidation by strongly bound hydroxyl species and Cr segregation: H2O and O2 adsorption on Fe-17Cr

The initial stages of surface oxidation of Fe-17Cr (ferritic stainless steel) were investigated at 323 K by X-ray photoelectron spectroscopy (XPS) and inelastic electron background analysis. The results indicated the formation of a mixed iron-chromium oxide layer upon O₂ exposure and the formation of a thin chromium oxyhydroxide layer upon H₂O exposure. The oxidation of Fe did not occur in the latter case. Moreover, it was found that pre-exposing the Fe-17Cr surface to H₂O significantly hinders subsequent oxidation by O₂, thus providing a way to control the formation of nanoscale oxides on stainless steel materials. It was concluded that the formation of strongly bound hydroxyl species together with adsorbate-induced segregation of Cr severely limits the reaction between O₂/H₂O and Fe from the alloy.