Poly(methyl methacrylate) hollow particles by water-in-oil-in-water emulsion polymerization

Poly(methyl methacrylate) particles having hollow structures were produced by water-in-oil-in-water (W/O/W) emulsion polymerization where sorbitan monooleate (Span80) was used as a primary surfactant and sodium laurylsulfate and Glucopen (APG, polypeptide derivative) were used as secondary surfactants. Urethane acrylate having a molecular structure with a hard segment in the molecular backbone, a long soft segment in the middle, and vinyl groups at both ends was employed as a reactive viscosity enhancer. At low concentration of urethane acrylate, only a few particles contained a void in the polymer phase. However, as the concentration of urethane acrylate increased, the number of the particles containing the void increased. This was because urethane acrylate increased the viscosity of the monomer mixture and helped to form the stable W/O/W emulsion droplets, which possibly restricted droplet coalescence during emulsion polymerization. Moreover, at high concentration of urethane acrylate (above 7 wt%), multi-hollow-structured particles were obtained. It is believed that the increase in the lyophilicity of the monomer mixture caused by urethane acrylate led to stronger interfacial activity of the primary surfactant (Span80) and finally resulted in many internal aqueous droplets. Received: 31 July 1998 Accepted: 13 October 1998     

Poly(methyl methacrylate) composites prepared by in situ polymerization using organophillic nano-to-submicrometer zinc oxide particles

Nano- and submicrometer zinc(II) oxide particles were synthesized by the polyol method and were used for the preparation of ZnO/poly(methyl methacrylate) (ZnO/PMMA) composite materials by the chain polymerization of methyl methacrylate (MMA) in bulk. ZnO particles with an organophilic surface layer were homogeneously dispersed in the PMMA matrix. Very low concentrations (0.1 wt.%) of nano zinc oxide absorbed over 98% of UV light as determined by UV-vis spectroscopy. Nano zinc oxide (75 nm) increased the initial decomposition temperature of the PMMA matrix by 30-40 °C at concentrations of 0.1% and above. This was explained by the changes in the termination mechanism of MMA polymerization resulting in a reduced concentration of vinylidene chain ends. Nano ZnO also increased the MMA polymerization reaction rate and reduced the activation energy. Submicrometer ZnO showed lower UV absorption, thermal stabilization and no influence on the reaction kinetics indicating that average particle size is of vital importance for the properties of PMMA nanocomposites and for MMA polymerization.     

Thermal properties of poly(methyl methacrylate) prepared by emulsifier-free emulsion polymerization

Emulsifier-free emulsion polymerization of methyl methacrylate in the presence of potassium persulfate initiator, taken in several different concentrations, at various pH values was studied with the aim to obtain colloidal crystals. The thermal properties of poly(methyl methacrylate) prepared by emulsifier-free emulsion polymerization, as the starting material for fabrication of photonic crystals, were examined in relation to the synthesis conditions.     

Stereoregularity of poly(methyl methacrylate) prepared by aqueous polymerization and catalyzed by corundum

The aqueous polymerization of methyl methacrylate was carried out in the absence and in presence of corundum or carborundum at 25 and 80°C. In the absence of corundum and carborundum, it has been found that rising the polymerization temperature from 25 to 80°C resulted in changing the tacticity of the obtained polymers. At 25°C the isotactic triad was 26% while the heterotactic triad was 33.5% and the syndiotactic one was 40.5%. Increasing the polymerization temperature to 80°C resulted in a decrease of the isotactic structure to 0% and increased the heterotactic structure and syndiotactic structure to 48 and 52% respectively. Polymerizing at 25°C in presence of corundum (0.5 g) an increase in the syndiotactic triad took place from 40.5 to 50.7% while the isotactic triad decreased from 26 to 22.2% and the heterotactic structure decreased from 33.5 to 27%. Raising the polymerization temperature to 80°C in the presence of the same amount of corundum resulted in an increase in both the isotactic and heterotactic triads to 35 and 32.7%, respectively. Polymerizing at 80°C in presence of corundum (0.5 g) resulted in nearly an equal percentage of each triad 33%.     

Polypropylene-block-poly(methyl methacrylate) and-block-poly(N-isopropylacrylamide) block copolymers prepared by controlled radical polymerization with polypropylene macroinitiator

Polypropylene-block-poly(methyl methacrylate) (PP-b-PMMA) and Polypropylene-block-poly(N-isopropylacryramide) (PP-b-PNIPAAm) block copolymers were successfully synthesized by radical polymerizations of MMA or NIPAAm with polypropylene (PP) macroinitiators. Polypropylene macroinitiators were prepared by a series of end functionalization of pyrolysis PP via hydroalumination, oxidation and esterification reactions. The PP macroinitiators thus obtained could initiate radical polymerizations of MMA or NIPAAm by using transition metal catalyst systems, and ¹H NMR analysis and gel permeation chromatography measurement confirmed the formation of PP-b-PMMA and PP-b-PNIPAAm block copolymers. In addition, the length of the incorporated PMMA or PNIPAAm segments in these block copolymers was controllable by the feed ratio between the monomer and the PP macroinitiator, and their molecular weights were estimated to be 35700 and 68700 (PMMA) and 1760 and 13300 (PNIPAAm), respectively. Transmission electron microscopy of the polymers obtained by NIPAAm polymerization revealed specific morphological features that reflected the difference of PNIPAAm segment length. The text was submitted by the authors in English.     

Anomalous viscosity behavior of some poly(methyl methacrylate)s prepared by anionic polymerization

A series of poly(methyl methacrylate)s with molecular weights in the range 3.0 × 10⁴–1.03 × 10⁶ have been prepared by anionic polymerization and their limiting viscosity numbers determined in a variety of solvents. It was found that whereas the higher-molecular-weight polymers behaved normally, the lower-molecular-weight polymers showed anomalous behavior. First, the limiting viscosity numbers of the lower-molecular-weight polymers were much higher than expected, and, second, their number-average molecular weights as measured by gel permeation chromatography were considerably smaller than those determined by membrane osmometry.     

Radical polymerization of methyl methacrylate with 2,2,3-triphenylpropanoic acid as an initiator

An unsymmetrical compound, 2,2,3-triphenylpropanoic acid (TPPA), was successfully prepared from phenyllithium, 1,1-diphenylethylene (DPE), gas carbon dioxide (CO₂), and aqueous standard solution of hydrochloric acid with LiCl deprivation. Characterization of the compound was performed by ¹H and ¹³C nuclear magnetic resonance (NMR) spectroscopy. The polymerization of methyl methacrylate (MMA) was performed in the presence of TPPA at 95 °C. The free radicals obtained were characterized by ultra-performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (UPLC/Q-TOF MS). Gel permeation chromatography (GPC) traces of the average molecular weight of poly(MMA) (PMMA) showed a series of translations with increasing time. The average molecular weight of PMMA indicated narrow polydispersity, and an approximately linear relationship was found between ln ([M]₀/[M]) and polymerization time.

Poly(methyl methacrylate) grafted imogolite nanotubes prepared through surface-initiated ARGET ATRP

Poly(methyl methacrylate) grafted imogolite clay nanotubes were fabricated via activators regenerated by electron transfer for atom transfer radical polymerization (ARGET ATRP) by designing a water-soluble amphiphilic ATRP initiator that can adsorb onto imogolite surface in an aqueous solution.     

Poly(ethylene oxide) gel as a novel polymerization medium anionic polymerization of methyl methacrylate

Crosslinked poly(ethylene oxide)-(PEO-N) is used as a novel medium for the anionic polymerization of methyl methacrylate (MMA) initiated by t-BuOK and ethyl-α-lithioisobutyrate (α-LiEtIB) in toluene. Comparative studies with linear poly(ethylene oxide)-(PEO-L) are performed as well. It is found that PEO-N effectively binds both initiators, and the polymerization process takes place mainly in the gel phase. PEO-N accelerates the polymerization process initiated by t-BuOK enabling the formation of high-molecular-weight polymers with high yields. Part of poly(methyl methacrylate)-(PMMA) remains in the gel particles yielding semi-interpenetrating networks with amphiphilic properties. PEO additives do not influence profoundly the course of the polymerization, initiated by α-LiEtIB. The influence of PEO-N on the proceeding of the polymerization is discussed in some detail.     

Effect of interfacial adhesion on the mechanical properties of poly(vinyl chloride) modified with cross-linked poly(methyl methacrylate) particles prepared by seeded emulsion polymerization

The effect of interfacial adhesion on the mechanical properties of an incompatible polymer blend was investigated. For this purpose, the preparation of non-cross-linked and cross-linked poly(methyl methacrylate) particles having mean sizes of about 0.8 μm was completed by seeded emulsion polymerization, and the number and the distribution of cross-linked points in the particles were varied. The emulsion particles obtained were powdered by a freeze–dry method and dispersed into a poly(vinyl chloride) matrix by melt blending. The non-cross-linked particles were completely dissolved in the matrix because poly(methyl methacrylate) has good compatibility with poly(vinyl chloride). On the other hand, in the case of the cross-linked particles, the mutual diffusion of the polymer molecules was restricted within the particle/matrix interfacial regions owing to the cross-linked points. Additionally, interfacial structures with different concentration slope dependent upon the number and the distribution of inner cross-linked points were developed with the same domain size. Mechanical and fracture properties were measured. As a result, both yield stress and fracture toughness decreased with a decrease in the interfacial adhesion, and the decrease was found to occur as a result of interfacial debonding. When the interfacial adhesion was sufficient it was never observed that the level was lower than that of the components. Received: 6 April 2000 Accepted: 29 September 2000     

Structure and properties of poly(methyl methacrylate) particles prepared by a modified microemulsion polymerization

Nanoscale poly(methyl methacrylate) (PMMA) particles were prepared by modified microemulsion polymerization. Different from particles made by traditional microemulsion polymerization, the particles prepared by modified microemulsion polymerization were multichain systems. PMMA samples, whether prepared by the traditional procedure or the modified procedure, had glass-transition temperatures (T_g's) greater than 120 °C and were rich in syndiotactic content (55–61% rr). After the samples were dissolved in CHCl₃, there were decreases in the T_g values for the polymers prepared by the traditional procedure and those prepared by the modified process. However, a more evident T_g decrease was observed in the former than in the latter; still, for both, T_g was greater than 120 °C. Polarizing optical microscopy and wide-angle X-ray diffraction indicated that some ordered regions formed in the particles prepared by modified microemulsion polymerization. The addition of a chain-transfer agent resulted in a decrease in both the syndiotacticity and T_g through decreasing polymer molecular weight. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 733–741, 2004     

Mass spectrometry of poly(methyl methacrylate) (PMMA) prepared by atom transfer radical polymerization (ATRP)

Poly(methyl methacrylate) (PMMA) was synthesized via atom transfer radical polymerization (ATRP). As a catalyst copper(I)thiocyanate (CuSCN) was used with N-n-pentyl-2-pyridylmethanimine as a ligand. Infrared spectroscopy and matrix assisted laser desorption ionization time-of-flight mass spectrometry were used to characterize the synthesized polymers. From this it was clear that at least to some extent thiocyanate was present as end groups of the PMMA chains. This observation is discussed in view of a phenomenon called halogen exchange, which has been reported before for bromine/chlorine exchange in ATRP.     

Poly(methyl methacrylate)/poly(N-isopropylacrylamide) core-shell particles prepared by seeded precipitation polymerization: Unusual morphology and thermo-sensitivity of zeta potential

Poly（methyl methacrylate）/poly（N-isopropylacrylamide） （PMMA/PNIPAM） core-shell particles were synthesized by seeded precipitation polymerization of N-isopropylacrylamide （NIPAM） in the presence of PMMA seed particles. The anionic potassium persulfate was used as initiator, and acrylic acid as functional comonomer. It was shown that the weight ratio of the PNIPAM shell to the PMMA core can be greatly increased through continuous addition of NIPAM monomer at a relatively slow rate. PMMA/PNIPAM particles with different shell thickness were obtained by varying the amount of charged NIPAM monomers. These particles exhibited unique nonspherical core-shell morphology. PMMA core was partially coated by dense hair-like or antler-like PNIPAM shell depending on the shell thickness. The measurement of these particles＇ zeta potential at different temperatures showed that the absolute value of zeta potential unusually decreased as the particle size decreased with temperature.     

Free‐radical polymerization of methyl methacrylate with a tetrafunctional peroxide initiator

This study examined the use of a new tetrafunctional peroxide initiator in the bulk free‐radical polymerization of methyl methacrylate. The objective was to investigate the effect of using a multifunctional initiator through an examination of the rates of polymerization and the polymer properties. The molecular weights and radii of gyration were obtained with a size exclusion chromatograph equipped with an online multi‐angle laser light scattering detector. The performance of the tetrafunctional initiator was compared to that of a monofunctional counterpart [tert‐butylperoxy 2‐ethylhexyl carbonate (TBEC)]. The results showed that the new tetrafunctional peroxide initiator produced a faster rate of polymerization than TBEC at an equivalent concentration but also generated a polymer of a lower molecular weight. This trend was the opposite of what was observed in a previous study with styrene. When TBEC was used at a concentration four times that of the new tetrafunctional peroxide initiator, both produced equal rates of polymerization and similar molecular weights. The degree of branching was also investigated with radius‐of‐gyration plots. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5647–5661, 2004     

Nanohole structure prepared by a polystyrene-block-poly(methyl methacrylate)/poly(methyl methacrylate) mixture film

Cylindrical nanoporous structures were prepared by using a mixture film of polystyrene-block-poly(methyl methacrylate) copolymer (PS-b-PMMA) and PMMA homopolymer (hPMMA), and they were analyzed by transmission electron microtomography (TEMT), X-ray reflectivity (XR), and grazing incidence small-angle X-ray scattering. For this purpose, the mixture film was spin-coated onto a silicon wafer modified by a neutral brush for PS and PMMA blocks, which generates PMMA cylindrical microdomains oriented normal to the substrate. Two methods were employed to prepare nanoporous structures: (1) all of the PMMA phase (PMMA block and PMMA homopolymer) in the film was removed by UV irradiation, followed by rinsing with a selective solvent (acetic acid) to PMMA and (2) only PMMA homopolymer was removed by selective solvent etching without UV irradiation. We found via TEMT and XR that the nanoporous structure in the film prepared by UV irradiation exhibited almost perfect cylindrical shape throughout the entire film thickness. However, when the film was rinsed with a selective solvent, nanoporous structures were not straight cylinders but had a funnel shape in which the diameter of nanopores located near the top of the film was larger than that located near the bottom of the film.     

Photo-living radical polymerization of methyl methacrylate using alkoxyamine as an initiator

The photoradical polymerization of vinyl acetate was performed using 4-methoxy-2,2,6,6-tetramethylpiperidine-1-oxyl (MTEMPO) as the mediator in the presence of bis(alkylphenyl)iodonium hexafluorophosphate (BAI). The MTEMPO/BAI system using 2,2’-azobis(isobutyronitrile) or 2,2’-azobis(4-methoxy-2,4-dimethylvaleronitrile) as the initiator did not succeed in controlling the molecular weight and produced polymers that showed a bimodal gel permeation chromatography with the broad molecular weight distribution. On the other hand, the polymerization using 1-(cyano-1-methylethoxy)-4-methoxy-2,2,6,6-tetramethylpiperidine and BAI proceeded by the living mechanism based on linear increases in the first order time–conversion and conversion–molecular weight plots. The molecular weight distribution also increased with the increasing conversion due to cloudiness of the solution as the polymerization proceeded. It was found that the polymerization had a photolatency because the propagation stopped by interruption of the irradiation and was restarted by further irradiation.     

Polymerization of methyl methacrylate with ceric ion-methanol redox system

The polymerization of methyl methacrylate initiated by Ce⁴⁺ methanol redox system was studied in aqueous solution of nitric acid at 15°C. The polymerization was initiated by primary radicals formed from Ce⁴⁺/alcohol complex. Poly(methyl methacrylate) chains containing the alcohol residue were obtained. Variations in the temperatuare and concentration of the components of the redox system allowed the control of the rate of polymerization and molecular weight of the polymer. The concentration of the hydroxyl end groups in the poly(methyl methacrylate) of low molecular weight was determined by titration and by spectrometric method.     

Synthesis of poly(methyl methacrylate) nanocomposites via emulsion polymerization using a zwitterionic surfactant

The synthesis of nanocomposites via emulsion polymerization was investigated using methyl methacrylate (MMA) monomer, 10 wt % montmorillonite (MMT) clay, and a zwitterionic surfactant octadecyl dimethyl betaine (C18DMB). The particle size of the diluted polymer emulsion was about 550 nm, as determined by light scattering, while the sample without clay had a diameter of about 350 nm. The increase in the droplet size suggests that clay was present in the emulsion droplets. X-ray diffraction indicated no peak in the nanocomposites. Transmission electron microscopy showed that emulsion polymerization of MMA in the presence of C18DMB and MMT formed partially exfoliated nanocomposites. Differential scanning calorimetry showed an increase of 18 degrees C in the glass transition temperature (Tg) of the nanocomposites. A dynamic mechanical thermal analyzer also verified a similar Tg increase, 16 degrees C, for the partially exfoliated nanocomposites over poly(methyl methacrylate) (PMMA). Thermogravimetric analysis indicated a 37 degrees C increase in the decomposition temperature for a 20 wt % loss. A PMMA nanocomposite with 10 wt % C18DMB-MMT was also synthesized via in situ polymerization. This nanocomposite was intercalated and had a Tg 10 degrees lower than the emulsion nanocomposite. The storage modulus of the partially exfoliated emulsion nanocomposite was superior to the intercalated structure at higher temperatures and to the pure polymer. The rubbery plateau modulus was over 30 times higher for the emulsion product versus pure PMMA. The emulsion technique produced nanocomposites of the highest molecular weight with a bimodal distribution. This reinstates that exfoliated structures have enhanced thermal and mechanical properties over intercalated hybrids.     

聚甲基丙烯酸甲酯型高分子染料的合成

高分子染料的合成研究起于６０年代初［１］．１９７３年，Ｍａｒｅｃｈａｌ等实现了无色高分子材料与有色染料分子的化学键合［２～３］．目前，高分子染料已广泛应用于化妆品、涂料、填料、食品等领域并开始探索在液晶显示、半导体材料、激光记录、非线性光学材料、亲和...