Chemosensors in environmental monitoring: challenges in ruggedness and selectivity

Environmental analysis is a potential key application for chemical sensors owing to their inherent ability to detect analytes on-line and in real time in distributed systems. Operating a chemosensor in a natural environment poses substantial challenges in terms of ruggedness, long-term stability and calibration. This article highlights current trends of achieving both the necessary selectivity and ruggedness: one way is deploying sensor arrays consisting of robust broadband sensors and extracting information via chemometrics. If using only a single sensor is desired, molecularly imprinted polymers offer a straightforward way for designing artificial recognition materials. Molecularly imprinted polymers can be utilized in real-life environments, such as water and air, aiming at detecting analytes ranging from small molecules to entire cells. Figure       

Selective solid-phase extraction of bisphenol A using molecularly imprinted polymers and its application to biological and environmental samples

Molecularly imprinted polymers (MIPs) were prepared using bisphenol A (BPA) as a template by precipitation polymerization. The polymer that had the highest binding selectivity and ability was used as solid-phase extraction (SPE) sorbents for direct extraction of BPA from different biological and environmental samples (human serum, pig urine, tap water and shrimp). The extraction protocol was optimized and the optimum conditions were as follows: conditioning with 5 mL methanol–acetic acid (3:1), 5 mL methanol, 5 mL acetonitrile and 5 mL water, respectively, loading with 5 mL aqueous samples, washing with 1 mL acetonitrile, and eluting with 3 mL methanol. MIPs can selectively recognize, effectively trap and preconcentrate BPA over a concentration range of 2–20 μM. Recoveries ranged from 94.03 to 105.3 %, with a relative standard deviation lower than 7.9 %. Under the optimal condition, molecularly imprinted SPE recoveries of spiked human serum, pig urine, tap water and shrimp were 65.80, 82.32, 76.00 and 75.97 %, respectively, when aqueous samples were applied directly. Compared with C18 SPE, a better baseline, better high-performance liquid chromatography separation efficiency and higher recoveries were achieved after molecularly imprinted SPE.      

Synthesis of polyacrylamide gel beads with electrostatic functional groups for the molecular imprinting of bovine serum albumin

Synthetic materials capable of recognizing proteins are important in separation, biosensors and biomaterials. In this study, bovine serum albumin-imprinted soft-wet polyacrylamide gel beads were prepared via inverse-phase suspension polymerization, using acrylamide and N,N′-methylene diacrylamide as polymeric matrix components and methacrylic acid as functional monomer. The adsorption study showed, through the imprinting process, that the imprinted gel beads had much higher adsorption capacity than the nonimprinted gel beads, and that the matching of the surface zeta-potential between the templates and the imprinted gel beads can enhance the imprinting effect. Adsorption kinetics indicated that the adsorption process could be described as an apparent first-order kinetic process for the gel beads. From the adsorption isotherm curve, we found that the adsorption of the imprinted gel beads was in agreement with the Langmuir adsorption model. Moreover, selectivity testing of the imprinted gel beads showed that imprinted gel beads exhibited good recognition for BSA as compared to the control protein. We speculate that the formation of complementary shapes and multiple-point electrostatic interactions between the imprinting cavities and the template proteins are the two factors that lead to the imprinting effect.      

Chromatographic characterization of molecularly imprinted polymers

Recent efforts in the investigation of chromatographic characterization of molecularly imprinted polymers (MIPs) have focused mainly on the nature of heterogeneous binding sites. More data on the thermodynamics than on the kinetic features of MIP columns have been published. The present article addresses the sources of peak broadening and tailing, which are the main drawbacks often associated with imprinted polymers in chromatography for practical applications. With use of the theory of nonlinear chromatography, the peak properties of a MIP column, including the retention and peak broadening and tailing, can be well interpreted. Efforts to improve chromatographic efficiency using MIPs prepared by approaches different from the conventional method, including covalent imprinting and the format of uniformly sized spherical microbeads, are reviewed and discussed. This review leads to the conclusion that nonlinear chromatography theory is useful for characterizing chromatographic features of MIP columns, since a MIP is essentially an affinity-based chromatographic stationary phase. We expect more theoretical and experimental studies on the kinetic aspects of MIP columns, especially the factors influencing the apparent rate constant, as well as the analysis of the influences of mobile-phase composition on the chromatographic performance. In addition to revealing the affinity interaction by molecular recognition, slow nonspecific interactions which may be inherited from the imperfect imprinting and may be involved in the rebinding of the template to MIPs also need to be characterized. Figure The peak broadening and tailing associated often with molecularly imprinted polymers (MIPs) in column chromatography for practical applications can be well characterized by the theory of nonlinear chromatography.     

Preparation and characterization of molecularly imprinted microspheres for dibutyl phthalate recognition in aqueous environment

Molecularly imprinted microspheres (MIMs) were prepared by suspension polymerization for the binding and recognition of dibutyl phthalate (DBP). DBP was used as the template molecule, methacrylic acid as the functional monomer, ethylene dimethacrylate (EDMA) as the linking agent, PVA as the dispersing agent, and Span 60 as the surfactant. The MIMs were characterized with electron microscope scanning and rebinding experiments. The Scatchard plot revealed that the template‐polymer system has a two‐site binding behavior with dissociation constants of 4.05 and 0.515 mmol/L. The MIMs exhibited the highest selective rebinding to DBP at 736.85 μg/g. The recoveries of the MIM‐SPE column for DBP extraction was 94.75–101.9% with the RSD of 1.5–7.3%, indicating the feasibility of the prepared MIMs for DBP extraction. Finally, the method developed was used to analyze the trace levels of phthalate in aqueous environment samples.     

Development and application of molecularly imprinted polymers as solid-phase sorbents for erythromycin extraction

Six molecularly imprinted polymers (MIPs) of erythromycin (ERY) were prepared by noncovalent bulk polymerization using methacrylic acid (MAA) as the functional monomer. On the basis of binding analysis, the MIPs with 1:2 optimum ratio of template to MAA were selected for subsequent scanning electron microscopy and Brunauer–Emmett–Teller analyses, which indicated that the MIPs had more convergent porous structures than the nonimprinted polymers. The equilibrium binding experiments showed that the binding sites of MIPs were heterogeneous, with two dissociation constants of 0.005 and 0.63 mg mL⁻¹, respectively. Furthermore, the performance of the MIPs as solid-phase extraction (SPE) sorbents was evaluated, and the selectivity analysis showed that the MIPs could recognize ERY with moderate cross-reactivity for other macrolides. The overall investigation of molecularly imprinted SPE for cleanup and enrichment of the ERY in pig muscle and tap water confirmed the feasibility of utilizing the MIPs obtained as specific SPE sorbents for ERY extraction in real samples. Figure Schematic diagram of the preparation and application of the erythromycin imprinted molecularly imprinted polymers Suquan Song and Aibo Wu contributed equally to this work.     

Recognition of oxytocin by capillary electrochromatography with monolithic tetrapeptide-imprinted polymer used as the stationary phase

Using YPLG (Tyr-Pro-Leu-Gly), a tetrapeptide, as the template, an imprinted monolithic column was prepared and applied to the selective recognition of oxytocin based on the epitope approach and capillary electrochromatography (CEC). By optimizing the polymerization solution in terms of functional monomer, cross-linking reagent, porogen, and imprinted template via CEC evaluations of synthesized columns, an imprinted monolith with good recognition capacity (the imprinting factors for YPLG and oxytocin were 4.499 and 4.013, respectively) and high column efficiency (theoretical plates for YPLG and oxytocin were 22,995 plates/m and 16,952 plates/m, respectively) was achieved. In addition, the effects of various experimental parameters on the recognition of oxytocin, including the organic modifier content, the buffer concentration, and the pH value, were studied systematically. Furthermore, a mixture of oxytocin and other proteins was analyzed using this monolithic CEC column, and oxytocin was eluted much more slowly than other large biomolecules, which demonstrated the high selective recognition ability of such an imprinted monolith for oxytocin with PLG (Pro-Leu-Gly) as the epitope. Figure Separation of a mixture of oxytocin, BSA, bovine hemoglobin, ovalbumin, and lysozyme on the open column, the blank monolithic column, and the monolithic YPLG-imprinted column     

Temperature sensitive molecularly imprinted microspheres for solid-phase dispersion extraction of malachite green,crystal violet and their leuko metabolites

This article demonstrates the feasibility of an alternative strategy for producing temperature sensitive molecularly imprinted microspheres (MIMs) for solid-phase dispersion extraction of malachite green, crystal violet and their leuko metabolites. Thermo-sensitive MIMs can change their structure following temperature stimulation. This allows capture and release of target molecules to be controlled by temperature. The fabrication technique provides surface molecular imprinting in acetonitrile using vinyl modified silica microspheres as solid supports, methacrylic acid and N-isopropyl acrylamide as the functional monomers, ethyleneglycol dimethacrylate as the cross-linker, and malachite green as the template. After elution of the template, the MIMs can be used for fairly group-selective solid phase dispersion extraction of malachite green, crystal violet, leucomalachite green, and leucocrystal violet from homogenized fish samples at a certain temperature. Following centrifugal separation of the microspheres, the analytes were eluted with a 95:5 mixture of acetonitrile and formic acid, and then quantified by ultra-high performance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS) with isotope internal calibration. The detection limits for malachite green, crystal violet and their metabolites typically are 30 ng·kg^?1. Positive samples were identified by UHPLC-MS/MS in the positive ionization mode with multiple reaction monitoring. The method was applied to the determination of the dyes and the respective leuko dyes in fish samples, and accuracy and precision were validated by comparative analysis of the samples by using aluminum neutral columns.

Open image in new window

Graphical abstract We describe an alternative strategy for producing temperature sensitive molecularly imprinted microspheres for solid-phase dispersion extraction of malachite green, crystal violet and their metabolites in fish samples.

     

Forensic analysis of dyed textile fibers

A rapid, specific, and sensitive method has been developed using molecularly imprinted polymers (MIPs) as solid-phase extraction sorbents for extraction of trace tetracycline antibiotics (TCs) in foodstuffs. MIPs were prepared by precipitation polymerization using tetracycline as the template. Under the optimal condition, the imprinting factors for MIPs were 4.1 (oxytetracycline), 7.0 (tetracycline), 7.4 (chlortetracycline), 7.7 (doxycycline), respectively. Furthermore, the performance of MIPs as solid-phase extraction sorbents was evaluated and high extraction efficiency of molecularly imprinted solid-phase extraction (MISPE) procedure was demonstrated. Compared with commercial sorbents, MISPE gave a better cleanup efficiency than C18 cartridge and a higher recovery than Oasis HLB cartridge. Finally, the method of liquid chromatography–tandem mass spectrometry coupled with molecular-imprinted solid-phase extraction was validated in real samples including lobster, duck, honey, and egg. The spiked recoveries of TCs ranged from 94.51% to 103.0%. The limits of detection were in the range of 0.1–0.3 μg kg⁻¹. Chromatograms obtained by direct injection of the spiked egg extracts (5 × 10^-3 mmol L⁻¹) and purification with MISPE     

Selective solid-phase extraction of tebuconazole in biological and environmental samples using molecularly imprinted polymers

Molecularly imprinted polymers (MIPs) were prepared by precipitation polymerization using tebuconazole (TBZ) as a template. Frontal chromatography and selectivity experiments were used to determine the binding capabilities and binding specificities of different MIPs. The polymer that had the highest binding selectivity and capability was used as the solid-phase extraction (SPE) sorbent for the direct extraction of TBZ from different biological and environmental samples (cabbage, pannage, shrimp, orange juice and tap water). The extraction protocol was optimized and the optimum conditions were: conditioning with 5 mL methanol:acetic acid (9:1), 5 mL methanol and 5 mL water respectively, loading with 5 mL aqueous samples, washing with 1.2 mL acetonitrile (ACN):phosphate buffer (5:5, pH3), and eluting with 3 mL methanol. The MIPs were able to selectively recognize, effectively trap and preconcentrate TBZ over a concentration range of 0.5–15 μmol/L. The intraday and interday RSDs were less than 9.7% and 8.6%, respectively. The limit of quantification was 0.1 μmol/L. Under optimum conditions, the MISPE recoveries of spiked cabbage, pannage, shrimp, orange juice and tap water were 62.3%, 75.8%, 71.6%, 89% and 93.9%, respectively. MISPE gave better HPLC separation efficiencies and higher recoveries than C18 SPE and strong cation exchange (SCX) SPE. Figure HPLC analysis of spiked pannage after MISPE (A) and after C18 SPE (B). HQ (1), E3 (2), p-NP (3), FTF (4), TBZ (5), PNZ (6), HXZ (7) Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Molecularly imprinted polymers labeled with amino-functionalized carbon dots for fluorescent determination of 2,4-dinitrotoluene

The authors have prepared amino-functionalized carbon dots (AC-dots) and applied them to fluorescently label a molecularly imprinted polymer (MIP) prepared by using 2,4-dinitrotoluene (DNT) as a template. Since DNT can retard vinyl polymerization, poly(methyl acrylate-co-acrylic acid) was used as a monomer. Non-imprinted polymers (NIPs) were also synthesized in order to compare data. As expected, MIPs exhibit higher adsorption than NIPs, with imprinting efficiencies ranging from 2 to 2.5. DNT is specifically captured by the cavities in the MIP and interact with AC-dots on the surface, resulting in quenching of the fluorescence of the AC-dots. Response to DNT reaches equilibrium within ~30 min. The method has a dynamic range that extends from 1 to 15 ppm, and allows for quantitation of DNT in aqueous solutions, with a detection limit of 0.28 ppm. Selectivity tests conducted in presence of DNT analogs demonstrated the selective recognition of DNT.

Open image in new window

Graphical Abstract Schematic of the preparation of molecularly imprinted polymers labeled with amino-functionalized carbon dots (AC-dots) for the quenchometric determination of 2,4-dinitrotoluene (DNT).

     

沉淀聚合法制备右旋邻氯扁桃酸分子印迹聚合物微球

以右旋邻氯扁桃酸为模板,丙烯酰胺、乙二醇二甲基丙烯酸酯分别为功能单体和交联剂,采用沉淀聚合法制备了分子印迹聚合物微球,讨论了反应介质用量、聚合温度、引发剂的种类和用量对印迹微球的影响。实验表明：分子印迹微球与传统本体聚合法制备的聚合物相比具有更高的特异识别能力,通过Scatchard分析研究了聚合物的选择结合性能,结果表明分子印迹聚合物微球在识别右旋邻氯扁桃酸分子的过程中存枉两类结合位点,而空白聚合物微球只存在一类结合位点。     

Molecular recognition of endocrine disruptors by synthetic and natural 17β-estradiol receptors: a comparative study

A β-estradiol receptor binding mimic was synthesised using molecular imprinting. Bulk polymers and spherical polymer nanoparticles based on methacrylic acid and ethylene glycol dimethacrylate as the functional monomer and crosslinker, respectively, were prepared in acetonitrile. The selectivity was evaluated by radioligand binding assays. The imprinted polymers were very specific to β-estradiol since the control polymers bound virtually none of the radioligand. The bulk polymer was then employed to screen endocrine disrupting chemicals. Structurally related steroids like α-estradiol, estrone and ethynylestradiol showed, respectively, 14.0, 5.0 and 0.7% of relative binding to the β-estradiol polymer, whereas most unrelated chemicals did not bind at all. These results are compared to those obtained with a bioassay using stably transfected yeast cells in culture bearing the human estrogen receptor. The receptor was activated by several estrogen-like chemicals and to a lesser extent by some structurally related chemicals. Figure A molecularly imprinted polymer that was a synthetic receptor for beta-estradiol was used for the screening of endocrine disrupting chemicals that are structurally related or unrelated to beta-estradiol. The results were compared with the recognition of the compounds by the biological estrogen receptor expressed in yeast cells. Related steroids like alpha-estradiol, estrone and ethynylestradiol showed significant binding to the beta-estradiol imprinted polymer, whereas most unrelated chemicals did not bind. The biological receptor was activated by several estrogen-like chemicals, and to a lesser extent by some structurally related chemicals     

Evaluation of diazepam-molecularly imprinted microspheres for the separation of diazepam and its main metabolite from body fluid samples

Molecularly imprinted microspheres (MIMs) for the drug diazepam and its main metabolite (nordiazepam) were prepared and used to separate the two species from urine and serum samples via molecularly imprinted solid-phase extraction. The specific binding capacity for diazepam was determined to be 1.97 mg/g, resulting in an imprinting factor of 5.8. The MIMs exhibit highly selective binding affinity for tricyclic benzodiazepines. Water-acetonitrile-acetone mixtures were used as the washing solvent and resulted in complete baseline separation, with a recovery of >87% for diazepam and of 88% for nordiazepam. The limits of detection are 21.5 and 24.5 ng/mL, respectively.     

‘Gate effect’ in templated polyacrylamide membranes influences the electrotransport of proteins and finds applications in proteome analysis

Templating is an effective way for the structural modifications of a material and hence for altering its functional properties. Here protein imprinting was exploited to alter polymeric polyacrylamide (PAA) membranes. The sieving properties and selection abilities of the material formed were evaluated by studying the electrically driven transport of various proteins across templated PAA membranes. The sieving properties correlated with the templating process and depended on the quantity of template used during the polymerisation. For 1 mg/mL protein-templated membranes a ‘gate effect’ was shown, which induced a preferential migration of the template and of similar-size proteins. Such template preferential electrotransport was exploited for the selective removal of certain proteins in biological fluids prior to proteome analysis (depletion of albumin from human serum); the efficiency of the removal was demonstrated by analysing the serum proteome by two-dimensional electrophoresis experiments. Figure PAA templeted membrane for the electroremoval of serum albumin before proteome analysis     

Selective recognition and electrochemical detection of p-nitrophenol based on a macroporous imprinted polymer containing gold nanoparticles

We have combined the molecular imprinting and the layer-by-layer assembly techniques to obtain molecularly imprint polymers (MIPs) for the electrochemical determination of p-nitrophenol (p-NPh). Silica microspheres functionalized with thiol groups and gold nanoparticles (Au-NPs) were assembled on a gold electrode surface layer by layer. The electrode was then immersed into a solution of pyrrole and p-NPh (the template), and electropolymerization led to the creation of a polymer-modified surface. After the removal of the silica spheres and the template, electrochemical impedance spectroscopy and differential pulse voltammetry (DPV) were employed to characterize the surface. The results demonstrated the successful fabrication of macroporous MIPs embedded with Au-NPs on the gold electrode. The effects of monomer concentration and scan rate on the performance of the electrode were optimized. Excellent recognition capacity is found for p-NPh over chemically similar species. The DPV peak current is linearly related to concentration of p-NPh in the 0.1 μM to 1.4 mM range, with a 0.1 μM limit of detection (at S/N = 3).

Molecularly imprinted polymers (MIPs) and nanomaterials were combined to prepare a novel macroporous structured MIPs based electrochemical sensor for the investigation of an environmental pollutant, p-nitrophenol (p-NPh). The sensor exhibited a fast binding dynamics, good specific adsorption capacities, and high selective recognition to p-NPh.

     

Molecularly imprinted microspheres for the anticancer drug aminoglutethimide: Synthesis,characterization, and solid‐phase extraction applications in human urine samples

Molecularly imprinted microspheres (MIMs) for the anticancer drug aminoglutethimide (AG) were synthesized by aqueous suspension polymerization. The expected size and diameter of MIMs are controlled easily by changing one of the surfactant types, ratio of organic‐to‐water phase or stirring rate during polymerization. The obtained MIMs exhibit specific affinity toward AG with imprinting factor of 3.11 evaluated with a chromatographic model. The resultant MIMs were used as the SPE materials for the extraction of AG from human urine. A molecularly imprinted SPE (MISPE) method coupled with HPLC has been developed for the extraction and detection of AG in urine. Our results showed that most impurities from urine can be removed effectively after a washing step and the AG has been enriched effectively after MISPE operation with the recovery of >90% (n = 3). The developed MISPE–HPLC method could be used for enrichment and detection of AG in human urine.     

多壁碳纳米管表面邻苯二甲酸二(2-乙基)己酯印迹聚合物的制备及其在固相萃取中的应用

以苯基修饰的多壁碳纳米管为载体,邻苯二甲酸二(2-乙基)己酯为模板分子,甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,在碳纳米管表面接枝一层塑化剂邻苯二甲酸二(2-乙基)己酯印迹聚合层.采用红外光谱和扫描电镜对聚合物进行表征和分析.结果表明,在碳纳米管表面成功接枝一层20～30 nm厚的印迹聚合层.采用高效液相色谱研究该印迹聚合物的吸附性能,结果表明,碳纳米管分子印迹聚合物对邻苯二甲酸二(2-乙基)己酯最大吸附量为69.1 μmol/g,达到吸附平衡时间约为60 min.选择性吸附实验表明,与其它结构类似物相比,该印迹复合材料对邻苯二甲酸二(2-乙基)己酯有良好的识别能力.作为固相萃取材料装填于固相萃取柱中,该印迹聚合物能对芒果汁样品中塑化剂进行有效的分离和富集.     

Development of a selective molecularly imprinted polymer-based solid-phase extraction for indomethacin from water samples

A selective molecularly imprinted solid-phase extraction (MISPE) for indomethacin (IDM) from water samples was developed. Using IDM as template molecule, acrylamide (AM) or methacrylic acid (MAA) as functional monomer, ethylene dimethacrylate (EDMA) as crosslinker, and bulk or suspension polymerization as the synthetic method, three molecularly imprinted polymers (MIPs) were synthesized and characterized with a rebinding experiment. It was found that the MIP of AM-EDMA produced by bulk polymerization showed the highest binding capacity for IDM, and so it was chosen for subsequent experiments, such as those testing the selectivity and recognition binding sites. Scatchard analysis revealed that at least two kinds of binding sites formed in the MIP, with the dissociation constants of 7.8 μmol L⁻¹ and 127.2 μmol L⁻¹, respectively. Besides IDM, three structurally related compounds — acemetacin, oxaprozin and ibuprofen — were employed for selectivity tests. It was observed that the MIP exhibited the highest selective rebinding to IDM. Accordingly, the MIP was used as a solid-phase extraction sorbent for the extraction and enrichment of IDM in water samples. The extraction conditions of the MISPE column for IDM were optimized to be: chloroform or water as loading solvent, chloroform with 20% acetonitrile as washing solution, and methanol as eluting solvent. Water samples with or without spiking were extracted by the MISPE column and analyzed by HPLC. No detectable IDM was observed in tap water and the content of IDM in a river water sample was found to be 1.8 ng mL⁻¹. The extraction efficiencies of the MISPE column for IDM in spiked tap and river water were acceptable (87.2% and 83.5%, respectively), demonstrating the feasibility of the prepared MIP for IDM extraction. Figure Molecularly imprinted polymer-based solid-phase extraction for indomethacin     

L-组氨酸手性识别印迹固定相的制备及表征

以L-组氨酸为模板分子, 甲基丙烯酸为功能单体, 乙二醇二甲基丙烯酸酯为交联剂, 偶氮二异丁腈为引发剂, 在水-乙腈微乳体系中采用沉淀聚合方法制备了具有手性识别L-组氨酸功能的印迹微球. 采用静态平衡吸附实验及色谱分析探讨聚合微球对模板分子的选择识别吸附性能. 结果表明, 该印迹聚合物微球对模板分子存在两种结合位点, 最大表观结合量分别为33.04和24.16 μmol/g. 相对于常规的C18柱, 该印迹聚合物填充柱能够完全分离L-组氨酸和D-组氨酸, 分离度R为2.23, 选择因子为2.14. 利用差热分析、红外光谱及X射线衍射等技术表征聚合物微球的热性能及结构. 结果表明, 聚合物微球具有良好的热稳定性, 是一种具有部分晶体结构的聚合物.