Determination of absorption length of CO2 and high power diode laser radiation for ordinary Portland cement and its influence on the depth of melting

The laser beam absorption lengths of CO₂ and a high power diode laser (HPDL) radiation for concrete have been determined. By employing Beer–Lambert’s law the absorption lengths for concrete of CO₂ and a HPDL radiation were 470±22 μm and 177±15 μm, respectively. Indeed, this was borne out somewhat from a cross-sectional analysis of the melt region produced by both lasers which showed melting occurred to a greater depth when the CO₂ laser was used.     

Char characteristics and particulate matter formation during Chinese bituminous coal combustion

The characteristics of char particles and their effects on the emission of particulate matter (PM) from the combustion of a Chinese bituminous coal were studied in a laboratory-scale drop tube furnace. The raw coal was pulverized and divided into three sizes, <63, 63–100, and 100–200 μm. These coal samples were subjected to pyrolysis in N₂ and combusted in 20 and 50% O₂ at 1373, 1523, and 1673 K, respectively. Char samples were obtained by glass fiber filters with a pore size of 0.3 μm, and combustion-derived PM was size-segregated by a low pressure impactor (LPI) into different sizes ranging from 10.0 to 0.3 μm. The characteristics of char particles, including particle size distribution, surface area, pore size distribution, swelling behavior and morphology property, were studied. The results show that, coal particle size and pyrolysis temperature have significant influence on the char characteristics. The swelling ratios of char samples increase with temperature increasing from 1373 to 1523 K, then decrease when the temperature further increases to 1623 K. At the same temperature, the swelling ratios of the three size fractions are markedly different. The finer the particle size, the higher the swelling ratio. The decrease of swelling ratio at high temperature is mainly attributed to the high heating rate, but char fragmentation at high temperature may also account for the decrease of swelling ratio. The supermicron particles (1–10 μm) are primarily spherical, and most of them have smooth surfaces. Decreasing coal particle size and increasing the oxygen concentration lead to more supermicron-sized PM formation. The influence of combustion temperature on supermicron-sized PM emission greatly depends on the oxygen concentration.     

Ignition of single coal particle in a hot furnace under normal- and micro-gravity condition

An experimental study on ignition and combustion of single particles was conducted at normal gravity (1-g) and microgravity (μ-g) for three high volatile coals with initial diameter of 1.5 and 2.0 mm, respectively. The non-intrusive twin-color pyrometry method was used to retrieve the surface temperature of the coal particle through processing the images taken by a color CCD camera. At the same time, a mathematical model considering thermal conduction inside the coal particle was developed to simulate the ignition process.Both experiments and modeling found that ignition occurred homogeneously at the beginning and then heterogeneously for the testing coal particles burning at μ-g. Experimental results confirmed that ignition temperature decreased with increasing volatile content and increasing particle size. However, contradicted to previous studies, this study found that for a given coal with certain particle size, ignition temperature was about 50–80 K lower at μ-g than that at 1-g.The model predictions agreed well with the μ-g experimental data on ignition temperature. The criterion that the temperature gradient in the space away from the particle surface equaled to zero was validated to determine the commence of homogeneous ignition. Thermal conduction inside the particle could have a noticeable effect for determining the ignition temperature. With the consideration of thermal conduction, the critical size for the phase transient from homogeneous to heterogeneous is about 700 μm at ambient temperature 1500 K and oxygen concentration 0.23.     

Micro-photoluminescence of GaN quantum dots embedded in 100 nm wide cylindrical AlN pillars

Individual pillars were etched from a sample embedding a single plane of GaN/AlN quantum dots, deposited by molecular beam epitaxy on a sapphire substrate. Pillars with diameters ranging from 0.1 to 5 μm were fabricated by electron-beam lithography and SiCl₄ reactive ion etching. The PL from a single pillar could be measured by using a confocal microscope, with a spatial resolution of 600 nm. We report an intense PL signal from pillar diameters as small as 0.1 μm at room temperature. By increasing the power of the excitation laser from 0.05 to 200 μW, we induced a blue-shift of the PL energy peak from 2.38 to 2.86 eV, accompanied by a substantial broadening of the PL line. This is explained by the photo-induced screening of the internal electric field, which is close to 10 MV/cm in GaN/AlN heterostructures. Finally we report and tentatively explain a photodarkening effect, i.e., the progressive decrease of the PL intensity over two orders of magnitude, after one hour of continuous laser excitation. However, this effect does not seem to be correlated to the etching process.     

Manufacturing of nanoscale thickness gold lines by laser curing of a discretely deposited nanoparticle suspension

The present work is focused on a novel method for the manufacturing of electric microconductors for semiconductors and other devices. Three different technologies are combined in this technique: controlled (drop on demand) printing, laser curing, and the employment of nanoparticles of matter, possessing markedly different properties (here, melting point) than their bulk counterparts. A modified on demand ink jet process is utilized to print electrically conducting line patterns from a suspension of gold nanoparticles in toluene. Microdroplets of 60–100 μm diameter are generated and deposited on a moving substrate such that the droplets form continuous lines. Focused laser irradiation is utilized in order to evaporate the solvent, melt the metal nanoparticles in the suspension, and sinter the suspended particles to form continuous, electrically conducting gold microlines on a substrate. The ultrafine particles in the suspension have a diameter size range of 2–5 nm. Due to curvature and surface effects of such small particles, the melting point is markedly lower than that of bulk gold (1063 C). Atomic force microscopy and scanning electron microscopy have been employed to investigate the topology of the cured line. In situ visualization of the curing process has been conducted. Results on the effect of the laser irradiation power on the topology and width of the cured line, which is directly related to the electrical conductivity, are reported.     

Evidence for the transition from the diffusion-limit in aluminum particle combustion

This work presents experimental evidence that the transition from gas-phase diffusion-limited combustion for aluminum particles begins to occur at a particle size of 10 μm at a pressure of 8.5 atm. Measurements of the particle temperature by AlO spectroscopy and three-color pyrometry indicate that the peak temperature surrounding a burning particle approaches the aluminum boiling temperature as particle size is decreased to 10 μm when oxygen is the oxidizer. This reduction indicates that reactions are occurring at or near the particle surface rather than in a detached diffusion flame. When CO₂ is the oxidizer, the combustion temperatures remain near the aluminum boiling temperature for particles as large as 40 μm, indicating that the flame is consistently near the surface throughout this size range. Burn time measurements of 10 and 2.8 μm powders indicate that burn time is roughly proportional to particle diameter to the first power. The burn rates of micron- and nano-particles also show strong pressure dependence. These measurements all indicate that the combustion has deviated from the vapor-phase diffusion limit, and that surface or near-surface processes are beginning to affect the rate of burning. Such processes would have to be included in combustion models in order to accurately predict burning characteristics for aluminum with diameter less than 10 μm.     

The effects of powder properties on in-flight particle velocity and deposition process during low pressure cold spray process

In cold spray process, impacting velocity and critical velocity of particles dominate the deposition process and coating properties for given materials. The impacting velocity and critical velocity of particles depend on the powder properties and cold spray conditions. In the present study, the in-flight particle velocity of copper powder in low pressure cold spraying was measured using an imaging technique. The effects of particle size and particle morphology on in-flight particle velocity and deposition efficiency were investigated. The critical velocity of copper powder was estimated by combining the in-flight particle velocity and deposition efficiency. The effect of annealing of feedstock powder on deposition and critical velocity was also investigated. The results showed that the irregular shape particle presents higher in-flight velocity than the spherical shape particle under the same condition. For irregular shape particles, the in-flight velocity decreased from 390 to 282 m/s as the particle size increases from 20 to 60 μm. Critical velocities of about 425 m/s and more than 550 m/s were estimated for the feedstock copper powder with spherical and irregular shape morphology, respectively. For the irregular shape particles, the critical velocity decreased from more than 550 to 460 m/s after preheating at 390 °C for 1 h. It was also found that the larger size powder presents a lower critical velocity in this study.     

Theoretical calculations of a square multilayer Bragg–Fresnel lens by quantum theory

A theoretical method based on the quantum scattering theory is presented to evaluate the performances of a two-dimensional (2-D) focusing square multilayer Bragg–Fresnel lens. The numerical application results of the square multilayer Bragg–Fresnel lens working at 0.7 nm wavelength (W/Si 25 periods with a double layer thickness of 5.38 nm, the size of the diffraction pattern is about 291×291 μm, the size of the center square in the diffraction pattern is 21.4×21.4 μm, and the size of the smallest square in the diffraction pattern is 0.39×0.39 μm) are given. Our theoretical results are compared with the experimental results of the linear Bragg–Fresnel lens reported by other researchers; an analysis and a discussion are carried out regarding the advantages of an optical system based on the 2-D focusing square multilayer Bragg–Fresnel lens, in contrast to a Kirkpatrick–Baez optical system on the basis of a two-linear Bragg–Fresnel lens.     

Characteristics of laser supersonic heating method for producing micro metallic particles

In this article, the authors analyzed the process characteristics of laser supersonic heating method for producing metallic particles and predicted the in-flight tracks and shapes of micro-particles. A pulse Nd–YAG laser was used to heat the carbon steel target placed within an air nozzle. The high-pressure air with supersonic velocity was used to carry out carbon steel particles in the nozzle. The shock wave structures at the nozzle exit were visualized by the shadowgraph method. The carbon steel particles produced by laser supersonic heating method were grabbed and the spraying angles of the particle tracks were visualized. The velocity of the in-flight particles was measured by a photodiode sensor and compared with the numerical result. The solidification of carbon steel particles with diameters of 1–50 μm in compressible flow fields were investigated. The result shows that there is no significant difference in the dimension of solid carbon steel particles produced at shock wave fields under various entrance pressures (3–7 bar) with a constant laser energy radiation.     

Diamond particles synthesized with graphite spark method in two seconds

A wide bandgap semiconductor, diamond, has recently emerged as important and promising materials for a wide field of optoelectronic and electronic applications. With graphite spark method in hydrogenic atmosphere, we successfully synthesized diamond particles in 3–5 μm diameter in only ten seconds and in 1–2 μm diameter in two seconds. The resultant particles were observed with SEM (Scanning Electron Microscope) images, and confirmed as diamond by sharp peak on 1331 cm⁻¹ with Raman spectrometer.With this study, we searched for precursors with various experimental conditions, such as hydrogen pressures and/or graphite temperatures. For gaseous species identification, OES (Optical Emission Spectroscopy) results will be reported on this presentation, and the preliminary synthesis mechanism for ‘spark method’ will be presented.     

Synthesis of Ca-P nanoparticles and fabrication of Ca-P/PHBV nanocomposite microspheres for bone tissue engineering applications

As the first step in producing totally bioresorbable osteoconductive composite scaffolds for bone tissue engineering using the selective laser sintering technology, bioresorbable nanoparticles of calcium phosphate (Ca-P) similar in composition to β-tricalcium phosphate were synthesized and Ca-P nanoparticle filled poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) microspheres were fabricated. The pH of the chemical reaction for Ca-P particle synthesis was found to have significant effects on the morphology and chemical composition of Ca-P precipitated. Ca-P particles produced at the pH of 10.0-11.0 were amorphous, had a Ca:P molar ratio of about 1.5, were spherical in shape and had sizes in the range of 10-30 nm. The Ca-P particles were used to form Ca-P nanocomposite microspheres through a solid-in-oil-in-water (S/O/W) emulsion solvent evaporation process. Ca-P nanoparticles were mostly encapsulated inside the microspheres and some Ca-P nanoparticles were superficially embedded on the microspheres. The Ca-P/PHBV microspheres had an average diameter of about 48 μm which is suitable for selective laser sintering for constructing osteoconductive composite scaffolds.     

Enhancement of field emission of SnO2 nanowires film by exposure of hydrogen gas

The effect of hydrogen (H₂) gas exposure on the field emission properties of tin oxide (SnO₂) nanowires films synthesized by the carbon thermal reduction vapor transport method was investigated. The exposure of H₂ gas results in the reduction of the turn-on voltage for driving a current of 10 nA from 7.6 V/μm to 5.5 V/μm and the increase of the field current based on 10 V/μm from 0.47 μA to 2.1 μA. The Fowler–Nordheim plot obtained from the current–voltage data supports that the field emission enhancement of SNW film is attributed to the reduction of the work function by the H₂ exposure.     

Flow characteristics and micro-scale metallic particle formation in the laser supersonic heating technique

The characteristics of the supersonic flow of the laser heating technique for producing micro-scale metallic particles were investigated in this study. A numerical model was established to predict the flow fields and particle trajectories leaving a spray nozzle with shock wave effects. The compressible flow of the shock waves and the trajectories of particles in diameters of 1–20 μm were simulated and compared with the flow visualization. In the experiment, a pulsed Nd-YAG laser was used as heat source on a carbon steel target within the nozzle, and the carbon steel particles were ejected by high-pressure air. The result shows that the shock wave structures were generated at various entrance pressures, and there is a significant increase in the amount of carbon steel particles and the spraying angles by increasing the entrance air pressure.     

Magneto-optic phase shift in plasmon propagation along garnet/semiconductor-on-insulator structures

This paper discusses the magneto-optic phase shift in garnet/semiconductor-on-insulator plasmonic waveguides. We consider two structures: (1) Y IG/Si/SiO₂ and (2) Y IG/GaInAsP/AlInAs-oxide. A dispersion relation for the plasmon propagation has been derived and the nonreciprocal phase shift of the fundamental TM mode has been determined at wavelengths of 1.55 μm, 1.5 μm and 1.3 μm.     

Structural characterization of ZnO/ Er2O3 core/shell nanowires

Zinc oxide/erbium oxide core/shell nanowires are of great potential value to optoelectronics because of the possible demonstration of laser emission in the 1.5 μm range. In this paper we present a convenient technique to obtain structures of this composition. ZnO core nanowires were first obtained by a vapor–liquid–solid (VLS) method using gold as a catalyst. ZnO nanowires ranging from 50 to 100 nm in width were grown on the substrates. Erbium was incorporated into these nanowires by their exposure to Er(tmhd)₃ at elevated temperatures. After annealing at 700 C in air, the nanowires presented 1.54 μm emission when excited by any of the lines of an Ar⁺ laser. An investigation of nanowire structure by HRTEM indicates that indeed the cores consist of hexagonal ZnO grown in the 001 direction while the surface contains randomly oriented Er₂O₃ nanoparticles. EXAFS analysis reveals that the Er atoms possess a sixfold oxygen coordination environment, almost identical to that of Er₂O₃. Taken collectively, these data suggest that the overall architectures of these nanowires are discrete layered ZnO/ Er₂O₃ core/shell structures whereby erbium atoms are not incorporated into the ZnO core geometry.     

Performance of CW NYAB laser at 1.06 μm end-pumped by a high-power diode-laser-array

A CW NYAB laser at 1.06 μm end-pumped by a high-power diode-laser-array has been demonstrated. At the incident pump power of 11 W, a maximum output power of 3.2 W was achieved, resulting in an optical conversion efficiency of 29.1%, and average slope efficiency of 37.5%. The output beam quality factor was measured to be M²=1.9. The internal losses caused by the NYAB crystal were measured to be 0.035 cm⁻¹. The NYAB crystal was also found to exhibit very strong thermal lensing under high-power end-pumped conditions.     

Laser characteristics of Cr:Nd:GdCOB self-frequency-doubling crystal

The phase matching angle of GdCOB crystal is calculated. By using Xenon flash lamp as pump source, we have realized the free run from 1.06 μm to 0.53 μm in self-frequency-doubling Cr:Nd:GdCOB (bi-doped) crystal and Nd:GdCOB (uni-doped) crystal. The experimental results show that the threshold energies for bi-doped crystal and uni-doped crystal are 0.92 J and 1.00 J, respectively; when the pump energy is 10 J, the output energies of green laser for two kinds of crystals are 2.46 mJ and 1.96 mJ, respectively. The output energy of Cr:Nd:GdCOB crystal has an increase of 25% in comparison to that of Nd:Gd:COB crystal. In addition, we discuss ways to improve efficiency.     

A new technique for the measurement of the product CO/CO2 ratio at the surface of char particles burning in a fluidized bed

A new experimental technique is proposed to measure the product CO/CO₂ ratio at the surface of spherical char particles during fluidized bed combustion. It is based on the measurement of the burning rate of a single char particle under low oxygen concentration conditions and on the use of an accurate prediction of the particle Sherwood number. This technique was applied to spherical char particles obtained from a bituminous coal which is characterized by a low attrition and fragmentation propensity. The product CO/CO₂ ratio was measured at a bed temperature of 850 °C and at a fluidization velocity of 0.3 m/s in a lab-scale apparatus operated with a bed of 0.5–0.6 mm sand. The char particle size was varied between 2 and 7 mm and the inlet oxygen concentration between 0.1% and 2.0%. Results showed that under the experimental conditions investigated carbon was mostly oxidized to CO₂ within the particle boundary layer, with a maximum fraction of carbon escaping as CO of 10–20% at the lowest oxygen concentrations and largest particle sizes.     

Effect of surrounding gas temperature on the morphological evolution of TiO2 nanoparticles generated by laser ablation in tubular furnace

Titanium oxide nanoparticles are synthesized by laser ablation of Ti target in oxygen atmosphere under well-controlled temperature profiles in a tubular furnace. The size and the shape of generated nanoparticles are varied by changing the temperature of furnace. The mobility-based size distributions of generated air-borne nanoparticles are measured using a scanning mobility particle sizer, and the size distributions of primary particles are analyzed by a scanning electron microscope. When the particles are generated by laser ablation at the room temperature, the particles are agglomerates in gas phase with the average mobility diameter of 117 nm and the mean diameter of primary particles of 11 nm. The primary particle diameter increases from 11 to 24 nm by raising the furnace temperature up to 800 °C. Since the mass of Ti vapor ablated from a target is found to be constant regardless of the furnace temperature, this particle growth may be attributed to the reduction in nuclei number as a result of mild quenching at higher temperatures. As the temperature reaches higher than 1,000 °C, the mobility diameter suddenly drops and the primary particle diameter increases due to sintering, and at 1,200 °C the mobility diameter coincides with the primary particle diameter. Since the laser oven method offers an independent control of vapor concentration and the temperature of surrounding atmosphere, it is an effective tool to study the formation process of nanoparticles from primary particles with a given size.     

Ultrafine ash aerosols from coal combustion: Characterization and health effects

Ultrafine coal fly-ash particles, defined here as those with diameters less than 0.5 μm, typically comprise less than 1% of the total fly-ash mass. These particles are formed primarily through ash vaporization, nucleation, and coagulation/condensation mechanisms, which lead to compositions notably different compared to other fine or coarse particle fractions formed by fragmentation. Whereas previous studies have focused on health effects of particulate matter with aerodynamic diameters less than 2.5 μm (PM_2.5) (including both vaporization and fragmentation modes), this paper reports results of interdisciplinary research focused on both characterization and health effects of primary ultrafine coal ash aerosols alone. Ultrafine, fine, and coarse ash particles were segregated and collected from a coal burned in a 20 kW laboratory combustor and two additional coals burned in an externally heated drop tube furnace. Extracted samples from both combustors were characterized by transmission electron microscopy (TEM), wavelength dispersive X-ray fluorescence (WD-XRF) spectroscopy, Mossbauer spectroscopy, and X-ray absorption fine structure (XAFS) spectroscopy. Pulmonary inflammation was characterized by albumin concentrations in mouse lung lavage fluid after instillation of collected particles in saline solutions and a single direct inhalation exposure. Results indicate that coal ultrafine ash sometimes, but not always, contains significant amounts of carbon, probably soot originating from coal tar volatiles, depending on coal type and combustion device. Surprisingly, XAFS results revealed the presence of chromium and thiophenic sulfur in the ultrafine ash particles. Although the single direct inhalation study failed to reveal significant health effects, the instillation results suggested potential lung injury, the severity of which could be correlated with the carbon (soot) content of the ultrafines. Further, this increased toxicity is consistent with theories in which the presence of carbon mediates transition metal (i.e., Fe) complexes, as revealed in this work by TEM and XAFS spectroscopy, promoting reactive oxygen species, oxidation–reduction cycling, and oxidative stress.