AuAg bimetallic nanoparticles film fabricated based on H2O2-mediated silver reduction and its application

A method to fabricate AuAg bimetallic nanoparticles film by H₂O₂-mediated reduction of silver was reported. Gold nanoparticles (Au NPs) were first adsorbed onto the surface of a self-assembled 2-aminoethanethiol monolayer-modified gold film or 3-aminopropyltriethoxysilane (APTES) monolayer-modified quartz slide. Upon further treatment of this modified film with the solution containing silver nitrate (AgNO₃) and H₂O₂, silver was deposited on the surface of Au NPs. The size of the AuAg bimetallic particles could be readily tuned by manipulating the concentration of H₂O₂. Surface plasmon resonance (SPR) was used to investigate the process, the deposition of silver on Au NPs modified gold film resulted in an obvious decrease of depth in the SPR reflectance intensity and minimum angle curves (SPR R-θ curves), which may be utilized for the quantitative SPR detection of the analyte, H₂O₂. Combination of the biocatalytic reaction that could yield H₂O₂ by using the enzyme, glucose oxidase, with the deposition of silver may enable the design of a glucose biosensor by SPR technique. Furthermore, we evaluated the AuAg bimetallic nanoparticles film for their ability to be an effective substrate for surface-enhanced Raman scattering (SERS).     

Film structures of poly(amido amine) dendrimers with an azacrown core and long alkyl chain spacers on water or Ag nanoparticle suspension

Newly designed poly(amido amine) dendrimers, which have an azacrown core, hexyl spacers, and methyl ester terminals (aza-C6-PAMAM dendrimer), were spread at the air-water and air-silver nanoparticle suspension interfaces, and their film structures were examined by surface pressure-area (pi-A) and surface potential-area (DeltaV-A) isotherms and epifluorescence microscopy. It was revealed that generation (G) 1.5 aza-C6-PAMAM dendrimer on a water subphase formed homogeneous film with face-on configuration, and this configuration was maintained during compression. On the other hand, a G2.5 dendrimer film on the air-water interface took initially homogeneous and face-on configuration that was followed by the conformational change during compression. Using a silver nanoparticle suspension as subphase, G1.5 film was significantly reinforced, and the partial collapse (cracks) in the film appeared as network texture. For a G2.5 dendrimer film, the pi-A and DeltaV-A isotherm properties were similar to that on the water subphase except for the collapsed film; small spots instead of cracks were formed under the film after collapse. These effects of the silver nanoparticle may be due to the formation of a dendrimer/silver nanoparticle composite. The formation process of the nanocomposite film was verified by UV-vis spectroscopy. For the G1.5 dendrimer, silver clusters and nanoparticles adsorbed to the dendrimer film after spreading and formed a small amount of aggregates. During compression, the aggregation proceeded even at low surface pressure. For the G2.5 dendrimer, a dendrimer/nanoparticle composite was also formed after spreading. However, with the initial compression, the absorption bands of clusters, nanoparticles, and aggregate increased together. Upon further compression, while the bands of cluster and nanoparticles decreased, the bands of aggregate still increased. These results suggest that the G2.5 dendrimer covered the cluster and nanoparticles more efficiently than the G1.5 dendrimer did because of the larger molecular size.     

Investigation of p-hydroxybenzoic acid from a new surface-enhanced Raman scattering system

In this paper, we developed a new kind of substrate, silver-coated indium tin oxide (ITO), to investigate the character of surface-enhanced Raman scattering (SERS) of p-hydroxybenzoic acid (PHBA). Homogeneous Ag-coated ITO substrate was obtained by decomposing AgNO(3) on the surface of ITO. A SERS spectrum of very good quality of "silver nanoparticles/PHBA/silver-coated ITO" was reported by adding PHBA aqueous solution and silver colloid onto the surface of silver-coated ITO repeatedly. PHBA molecules absorbed onto the surface of the silver nanoparticles through ionized carboxyl, and the PHBA molecules tended to tilt on the surface in this system. The rich information obtained from the silver nanoparticles/PHBA/silver-coated ITO system indicates that this is a highly SERS-active system. Not only was the number of the vibrational modes increased, but also were the frequencies of Raman bands shifted. The two SERS mechanisms, the "electromagnetic" and "chemical" mechanism, were mainly responsible for the experimental results. Furthermore, the silver nanoparticles modified on the silver-coated ITO surface play an important role in magnifying the surface local electric field near the silver film surface through resonant surface plasmon excitation.     

Anisotropic particles with different morphologies of silver nanoshell: Synthesis and optical properties

Hydrosols of spindle-shaped composite particles with the core of iron(III) oxyhydroxide and silver shell are synthesized by enlarging metal seeding nanoparticles adsorbed on the surface of the cores in the solution containing silver nitrate and mild reducing agent. It is revealed that the character of the growth of shells on gold seeding particles greatly depends on the type of reducing agent. When using ascorbic acid, seeding particles grow primarily in the direction normal to the core surface due to the blocking of some of the particle faces by ions present in the solution. As a result, the forming shell is characterized by a fairly nonuniform structure. At the same time, when using formaldehyde, the growth of seeding nanoparticles proceeds predominantly in the lateral direction to form first an island-like film, then a continuous thin metal shell on the core surface. It is demonstrated that the position of localized surface plasmon resonance of such structure can be fine tuned to the preset wavelength by controlled variations in the thickness of Ag shell with very small step (up to 1 nm).     

Ag/DNQ-novolac-based nanocomposite films for controllable UV lithography morphological patterning

In this study, the detailed characterisation of silver (Ag) nanoparticles/polymer nanocomposite chemical structure and morphology of grating has been carried out. Scanning electron microscopy measurements show spherical shape of Ag nanoparticles (40–80 nm in diameter) prepared in chloroform by reduction of silver nitrate. In the positive photoresist based on 2-diazo-2H-naphthalen-1-one (DNQ)–novolac, Ag nanoparticles were deposited from organic colloidal solution. The content of nanoparticles in the polymer matrix was varied by increasing the concentration of Ag colloidal solution. Grating was formed by contact lithography. The quantification of Ag nanoparticles and chemical analysis of Ag/DNQ-novolac-based nanocomposite was performed by means of energy dispersive X-ray analyzer and SEM/EDS. In order to study the effect of Ag nanoparticles on the DNQ-novolac-based nanocomposite structure, investigations with Fourier transform infrared spectroscopy were conducted. Ag nanoparticles cause changes associated with substituent-sensitive out-of-plane C–H bending vibrations of aromatic ring. Ag/DNQ-novolac-based nanocomposite film surface morphology and grating topography imaging were performed using atomic force microscopy. Added Ag nanoparticles change the geometrical parameters of the gratings. The split of corrugations was achieved in Ag/DNQ-novolac-patterned films. Their morphology can be tailored by altering the content of Ag nanoparticles.     

Antibacterial properties of Ag nanoparticle loaded multilayers and formation of magnetically directed antibacterial microparticles

Antibacterial coatings based on hydrogen-bonded multilayers containing in situ synthesized Ag nanoparticles were created on planar surfaces and on magnetic colloidal particles. We report the antibacterial properties of these coatings, determined using a disk-diffusion (Kirby-Bauer) test, as a function of the film thickness and the concentration of Ag nanoparticles in the hydrogen-bonded multilayers. The zone of inhibition (ZoI) determined by the disk-diffusion test increases as the thickness of the multilayer film is increased. Results obtained for the values of the ZoI as a function of film thickness can be described adequately with a simple diffusion model (i.e., the square of the zone of inhibition (ZoI) depended linearly on the logarithm of the thickness of the silver-loaded films). This observation suggests that, in order to incrementally increase the ZoI, an exponentially increasing amount of Ag is required within the multilayers. In general, there was no statistically significant correlation between the zone of inhibition and the number of Ag loading and reduction cycles. The duration of sustained release of antibacterial Ag ions from these coatings, however, could be prolonged by increasing the total supply of zerovalent silver in the films via multiple loading and reduction cycles. These results indicate that the release of silver is controlled by an oxidation mechanism at the surface of the nanoparticles and that repeated loading and reduction of silver leads preferentially to growth of the existing silver nanoparticles in the film as opposed to nucleation of new Ag nanoparticles. We also show that magnetic microspheres coated with silver nanoparticle loaded hydrogen-bonded multilayer thin films can be used to deliver antibacterial agents to specific locations. The minimum inhibitory concentration (MIC) of nanocomposite coated microspheres was determined by the agar dilution technique: antibacterial magnetic microspheres with higher concentrations of Ag nanoparticles exhibited lower MIC values.     

Silver-protein (core-shell) nanoparticle production using spent mushroom substrate

A simple route for the synthesis of silver-protein (core-shell) nanoparticles using spent mushroom substrate (SMS) has been demonstrated in this work. SMS exhibits an organic surface that reduces silver ions and stabilizes the silver nanoparticles by a secreted protein. The silver nitrate solution incubated with SMS changed to a yellow color from 24 h onward, indicating the formation of silver nanoparticles. The purified solution yielded the maximum absorbance at 436 nm due to surface plasmon resonance of the silver nanoparticles. X-ray analysis of the freeze-dried powder of silver nanoparticles confirmed the formation of metallic silver. Transmission electron microscopic analysis of the samples showed a uniform distribution of nanoparticles, having an average size of 30.5 +/- 4.0 nm, and its corresponding electron diffraction pattern confirmed the face-centered cubic (fcc) crystalline structure of metallic silver. The characteristic fluorescence of the protein shell at 435 nm was observed for the silver nanoparticles in solution, when excited at 280 nm, while Fourier transform infrared (FTIR) spectroscopy confirmed the presence of a protein shell. The silver nanoparticles were found to be stable in solution for more than 6 months. It is observed that the reducing agents from the safflower stalks caused the reduction of silver ions while protein secreted by the fungus stabilized the silver nanoparticles. These silver nanoparticles showed excellent antibacterial activity against two representative bacteria, Staphylococcus aureus (Gram positive) and Klebsiella pneumoniae (Gram negative), in spite of the presence of an organic layer as a shell. Apart from ecofriendliness and easy availability, "SMS" as a biomanufacturing unit will give us an added advantage in ease of handling when compared to other classes of microorganisms.     

纳米银碗阵列结构的高效制备及荧光增强性能

报道了一种以自组装单层聚苯乙烯纳米微球阵列为模板, 通过真空热蒸镀银纳米粒子高效制备大面积银碗阵列结构的方法. 测试结果表明, 制得的银碗阵列结构为微纳米复合分级结构, 银碗由平均粒径为10 nm的银纳米粒子组成. 紫外-可见吸收光谱测试结果表明, 银碗阵列结构表面具有银纳米粒子的局域表面等离子体共振吸收峰. 将荧光分子N,N'-二正丁基喹吖啶酮(DBQA)分别蒸镀到普通银膜和银碗阵列结构表面并测试了荧光光谱. 结果表明, 在银碗阵列结构表面的荧光分子强度得到了显著增强, 说明制备的银碗阵列结构是优良的荧光增强基底.     

A SERS-active system based on silver nanoparticles tethered to a deposited silver film

A series of SERS-active nanostructures were produced by exposing a freshly deposited silver film (fabricated to be as free from roughness as practicable) to a solution containing a mixture of 1-decanethiol (m) and 1,9-nonanedithiol (d) of varying concentrations of m to d, then allowing colloidal silver nanoparticles to interact with the surface. Silver nanoparticles were found to bind exclusively to films which were prepared from solutions with a nonzero concentration of the dithiol implying that the nanoparticles were tethered to the silver surface by the dithiol with one of the thiolate groups bound to the nanoparticle and the other to the silver film. Intense SERS spectra were observed even from samples in which the m/d concentration ratio was so large that the adsorbed molecules in the vicinity of only approximately 8 +/- 3 nanoparticles were illuminated by the diffraction-limited focused laser beam. At such high dilution, the molecules (numbering at most approximately 330) residing in the SERS "hot spots" associated with the approximately 8 nanoparticles consisted primarily of m (although, of course, for each nanoparticle, at least one molecule in the hot spot had to be d to serve as the linker). This was corroborated by the SERS spectra. An analysis is presented, which accounts for the fact that as the concentration ratio of m/d increases, the SERS intensity associated with bands belonging to m first increases to a maximum then decreases. The nanoparticle-metal film system presented here is a simple embodiment of a more general range of SERS-active sensing platforms in which a molecular tether is used to create a SERS hot spot that (although nanosized) is large enough to accommodate analyte molecules that cannot themselves function as linkers, which are subsequently detected by SERS at the few-molecule level.     

纳米银粒子对[Ru(bpy)_3]~(2+)光谱学性质的影响及电解质效应

研究了[Ru(bpy)3]2+溶液中引入纳米银粒子的光谱学性质变化规律以及[Ru(bpy)3]2+与纳米银粒子所构成的溶液体系([Ru(bpy)3]2+-Ag)的电解质效应.研究结果表明,[Ru(bpy)3]2+吸附在纳米银粒子表面使纳米银粒子相互桥连形成规则的类链状网络聚集体.纳米银粒子造成[Ru(bpy)3]2+溶液荧光猝灭,且大尺寸的纳米银粒子引起的荧光猝灭程度较大.在[Ru(bpy)3]2+-Ag体系中引入电解质造成纳米银粒子不同程度的聚集和生长.电解质对纳米银聚集影响为:CaCl2MgCl2Ca(NO3)2KClKNO3.随着[Ru(bpy)3]2+-Ag体系中引入电解质含量的增加,溶液的荧光强度先降低而后又逐渐增强,直至达到定值,表明一定量的电解质可产生荧光猝灭释放效应.电解质对荧光强度影响顺序为:Ca(NO3)2CaCl2MgCl2KClKNO3.采用透射电子显微镜、紫外-可见吸收分光光度计和荧光分光光度计等手段从分子间相互作用和能量传输等方面初步探讨了纳米银粒子对表面吸附[Ru(bpy)3]2+溶液光谱学性质的影响机制以及电解质效应.     

Novel silver nanostructures from silver mirror reaction on reactive substrates

Novel silver clusters have been prepared by simply carrying out the silver mirror reaction on certain reactive substrates. Leaflike fractal silver microstructures and perpendicularly aligned silver nanosheets were produced on a commercially available copper foil and sandpaper-rubbed copper foil, respectively. The surface features of copper foils and the chemical state of Cu atoms play important roles in regulating the morphological structures of the resulting silver clusters. Silver nanoclusters with various morphologies ranging from the leaflike to flowerlike hierarchical structures can be produced from the silver mirror reaction on commercially available copper foils after being treated with a dilute aqueous HCl solution under different conditions. The aqueous solution of silver nanosheets shows an optical absorption spectrum with a broad light-scattering peak at about 350 nm, compared to a corresponding surface plasmon absorption band around 430 nm for silver nanoparticles from the conventional silver mirror reaction on glass.     

Studies of electrochemical quantized capacitance charging of surface ensembles of silver nanoparticles

CTAB-stabilized silver nanoparticles were synthesized by NaBH₄ reduction. The as-prepared nanoparticles can be self-assembled on 3-mercaptopropionic acid (MPA) modified gold electrode, which was supported strongly by XPS measurements. Exceptional long-term stability of the as-prepared colloidal silver aqueous solution and the desorption of silver nanoparticle ensemble on MPA after alcohol rinsing proved that these CTAB molecules adsorbed on silver core formed interdigitated bilayer structure. DPV and differential capacitance measurements were performed to characterize the as-prepared silver nanoparticle ensemble, and the interesting quantized capacitance charging behaviors were observed.     

A new surface-enhanced Raman scattering system for C60 fullerene: Silver nano-particles/C60/silver film

Surface-enhanced Raman scattering (SERS) spectrum of very good quality of “silver nano-particles/C60/silver film” system was reported for the first time by using the pyridine as a intermediate to connect and nest the C60 molecules to the gap of silver nano-particles and silver film. Experiment results show that the ternary system of “silver nano-particles/C60/silver film” is very effective and active. Not only was the number of vibrational modes greatly increased, especially some modes that were forbidden in Raman spectrum, but also were the significant Raman bands splitted as well as frequencies up and down shifted, respectively, arising from symmetry lowering and selection rule relaxing of C60 induced by the silver surface. Furthermore, the splitting of the Raman modes is consistent with the calculation based on group theory. The adsorption of C60 molecules is oriented on pentagons of C60 on the silver surface. It is difficult to separate the contributions of the electromagnetic and chemical mechanisms to the great enhancement of the Raman signal. On the one hand, the silver nanoparticles modified on the silver film play an important role in magnifying the surface local electric field near the silver surface through resonant surface plasmon excitation. On the other hand, charge transfer factor may not be neglected.     

Electroless deposition of nickel on fluoropolymers modified by surface graft copolymerization

Surface modification of Ar plasma-pretreated poly(tetrafluoroethylene) (PTFE) and poly(vinylidene fluoride) (PVDF) films via UV-induced graft copolymerization with 4-vinylpyridine (4VP), 2-vinylpyridine (2VP) or 1-vinylimidazole (VIDz) was carried out. Electroless deposition of nickel could be carried out on these graft-modified fluoropolymer surfaces after PdCl₂ activation. The surface compositions of the graft-modified films were studied by X-ray photoelectron spectroscopy. The adhesion strength between the surface graft-copolymerized fluoropolymer film and the electrolessly deposited nickel was affected by the type of monomers used for graft copolymerization and the graft concentration. The optimum T-peel adhesion strengths of the electrolessly deposited Ni on the 4VP graft-copolymerized PTFE and PVDF surfaces were about 7 and 13 N/cm, respectively. The metal/fluoropolymer assemblies delaminated by cohesive failure inside the fluoropolymer substrates. The enhanced adhesion between the electrolessly deposited Ni and the surface-modified fluoropolymers is attributable to the interfacial charge transfer interactions between the grafted polymer chains and the deposited metals (Pd and Ni), the spatial distribution of the graft chains into the metal matrix and the covalent tethering of the graft chains on the fluoropolymer surface.     

Conversion of the surface property of oleic acid stabilized silver nanoparticles from hydrophobic to hydrophilic based on host-guest binding interaction

This paper describes a general method to change the surface property of the oleic acid stabilized silver nanoparticles and successful tranferring of the silver nanoparticles from the organic phase into the aqueous phase. By vigorous shaking of a biphasic mixture of the silver organosol protected with oleic acid and p-sulfonated calix[4]arene (pSC4) aqueous solution, it is believed that an inclusion complex is formed between oleic acid molecules and pSC4, and the protective layer of the silver nanoparticles shifts from hydrophobic to hydrophilic in nature, which drives the transfer of silver nanoparticles from the organic phase into the aqueous phase. The efficiency of the phase transfer to the aqueous solution depends on the initial pSC4 concentration. The pSC4-oleic acid inclusion complex stabilized nanoparticles can be stable for long periods of time in aqueous phase under ambient atmospheric conditions. The procedure of phase transfer has been independently verified by UV-vis, transmission electron microscopy, Fourier transform infrared, and 1H nuclear magnetic resonance techniques.     

One-step synthesis of silver nanoparticles, nanorods, and nanowires on the surface of DNA network

Here, we describe a one-step synthesis of silver nanoparticles, nanorods, and nanowires on DNA network surface in the absence of surfactant. Silver ions were first adsorbed onto the DNA network and then reduced in sodium borohydride solution. Silver nanoparticles, nanorods, and nanowires were formed by controlling the size of pores of the DNA network. The diameter of the silver nanoparticles and the aspect ratio of the silver nanorods and nanowires can be controlled by adjusting the DNA concentration and reduction time.     

The investigation of a series of n-hydroxybenzoic acids (n=p, m, o) on a new surface enhanced Raman scattering active substrate

Ag nanoparticles, organized on indium tin oxide (ITO) surface, can act as a new surface enhanced Raman scattering (SERS) active substrate as well as a dry electrode. Compared with the traditional SERS-active substrate, its notable advantage is that the microcosmic changes of the film can be reflected by the SERS spectrum during the investigation of the film's electrical and other macroscopic characteristics. To illuminate the above-mentioned property of this new substrate, a series of n-hydroxybenzoic acids (n-HBA; n=p, m and o) was tested as probe molecules by SERS technique. These SERS spectra indicate that the significant changes of frequencies as well as intensities, respectively, arise from the changes of the adsorption behavior along with the proportional variation of molecules and silver nanoparticles. Excellent SERS signals prove that the silver nanoparticles-coated ITO is a highly SERS-active substrate and can efficiently reflect the microcosmic property of the film, which suggest it has promising potential of being a new technique for further application in the field of thin-film research.     

Adsorption Behaviors of 4-Mercaptobenzoic Acid on Silver and Gold Films

The adsorption behaviors of 4-mercaptobenzoic acid on silver and gold nanoparticles were studied by surface-enhanced Raman scattering (SERS) and density functional theory. The silver and gold films by electrodeposition have the same excellent characteristics as SERS-active substrates. At the same, the SERS spectra indicate that 4-mercaptobenzoic acid molecules are adsorbed on the surfaces of gold nanoparticles through the S atom, and that the carboxyl group is far away from surface of gold nanoparticles, and that there is a certain angle between the plane of benzene ring and gold film. However, 4-mercaptobenzoic acid molecules are adsorbed on the surfaces of silver nanoparticles through the carboxyl group, and the S atom is far away from surface of silver nanoparticles, and there is also a certain angle between the plane of benzene ring and the surface of silver nanoparticles. Here it is demonstrated the calculated Raman frequencies are in good agreement with experimental values, and the calculated Raman frequencies are also helpful to infer the adsorption behaviors of 4-mercaptobenzoic acid molecules.     

Defining rules for the shape evolution of gold nanoparticles

The roles of silver ions and halides (chloride, bromide, and iodide) in the seed-mediated synthesis of gold nanostructures have been investigated, and their influence on the growth of 10 classes of nanoparticles that differ in shape has been determined. We systematically studied the effects that each chemical component has on the particle shape, on the rate of particle formation, and on the chemical composition of the particle surface. We demonstrate that halides can be used to (1) adjust the reduction potential of the gold ion species in solution and (2) passivate the gold nanoparticle surface, both of which control the reaction kinetics and thus enable the selective synthesis of a series of different particle shapes. We also show that silver ions can be used as an underpotential deposition agent to access a different set of particle shapes by controlling growth of the resulting gold nanoparticles through surface passivation (more so than kinetic effects). Importantly, we show that the density of silver coverage can be controlled by the amount and type of halide present in solution. This behavior arises from the decreasing stability of the underpotentially deposited silver layer in the presence of larger halides due to the relative strengths of the Ag(+)/Ag(0)-halide and Au(+)/Au(0)-halide interactions, as well as the passivation effects of the halides on the gold particle surface. We summarize this work by proposing a set of design considerations for controlling the growth and final shape of gold nanoparticles prepared by seed-mediated syntheses through the judicious use of halides and silver ions.     

Assessment of silver and gold substrates for the detection of amphetamine sulfate by surface enhanced Raman scattering (SERS)

Methods of detection of amphetamine sulfate using surface enhanced Raman scattering (SERS) from colloidal suspensions and vapour deposited films of both silver and gold are compared. Different aggregating agents are required to produce effective SERS from silver and gold colloidal suspensions. Gold colloid and vapour deposited gold films give weaker scattering than the equivalent silver substrates when high concentrations of drug are analysed but they also give lower detection limits, suggesting a smaller surface enhancement but stronger surface adsorption. A 10(-5) mol dm(-3) solution (the final concentration after addition of colloid was 10(-6) mol dm(-3)) of amphetamine sulfate was detected from gold colloid with an RSD of 5.4%. 25 microl of the same solution could be detected on a roughened gold film. The intensities of the spectra varied across the film surface resulting in relatively high RSDs. The precision was improved by averaging the scattering from several points on the surface. An attempt to improve the detection limit and precision by concentrating a suspension of gold colloid and amphetamine sulfate in aluminium wells did not give effective quantitation. Thus, positive identification and semi-quantitative estimation of amphetamine sulfate can be made quickly and easily using SERS from suspended gold colloid with the appropriate aggregating agents.