羧甲基香菇多糖表面修饰的聚乳酸材料的表面性能研究

制备了香菇多糖羧甲基衍生物,再通过化学接枝方法利用共价键将羧甲基香菇多糖固定在氨基化聚乳酸基材表面,得到羧甲基香菇多糖化学接枝修饰的聚乳酸材料.此外,通过在氨基化聚乳酸基材表面进行羧甲基香菇多糖与壳聚糖的层层自组装,得到生物多糖层层自组装修饰的聚乳酸材料.采用扫描电子显微镜、水接触角测量仪、抗菌活性测试、溶血试验和血栓试验等方法对被修饰聚乳酸材料的表面性能和生物性能进行了分析和比较.结果表明采用2种表面修饰方法得到的羧甲基香菇多糖修饰的聚乳酸材料的亲水性、血液相容性以及对大肠杆菌抗菌活性得到改善.与化学接枝方法相比,经过羧甲基香菇多糖与壳聚糖层层自组装修饰的聚乳酸材料具有更好的亲水性、血液相容性和抗菌活性.     

电活性可生物降解纳米复合材料PAP/op-HA/PLGA的制备及成骨活性

以苯胺五聚体与聚乳酸（PLA）的三嵌段共聚物（PAP）与表面接枝低聚乳酸的纳米羟基磷灰石（op-HA）和聚丙交酯-乙交酯（PLGA）的复合物共混,制备的电活性可降解纳米复合材料PAP/op-HA/PLGA为研究对象,采用紫外可见光谱、循环伏安扫描和标准四探针法分析其电化学特性及电导率。ESEM观察其膜表面形貌,接触角评价其亲水性。通过在材料膜表面接种兔成骨细胞进行体外培养,采用荧光染色、NIH Image J图像分析和Real-time PCR综合评价细胞在材料表面的粘附、扩展（细胞面积比）和成骨相关基因的表达水平,以此评价新型电活性纳米复合骨修复材料PAP/op-HA/PLGA的表面性质和生物活性。结果表明,PAP/op-HA/PLGA的电导率较低（~5?10?6 S/cm）但具有良好的电化学氧化还原性能,PAP含量为0.1%时材料的亲水性明显改善,成骨细胞的粘附和扩展明显增强。培养7天时骨形态蛋白- 2（BMP-2）和骨连接蛋白（Osteonectin）的基因表达水平明显提高,而对Ⅰ型胶原蛋白的基因表达没有明显影响。提示PAP/op-HA/PLGA具有良好的细胞相容性和成骨活性。     

聚乳酸接枝改性纳米生物玻璃/PLGA复合材料的制备、表面性质及生物活性

以丙交酯开环聚合原位接枝改性的纳米生物玻璃(PLLA-g-BG)与聚丙交酯-乙交酯(PLGA)复合材料为研究对象, 采用TGA, ESEM和EDX分析其接枝率, 粒子分散性和表面元素分布, 通过将兔成骨细胞种植于材料膜表面进行体外培养, 采用荧光染色法、NIH Image J图像分析软件、MTT法和流式细胞术等手段检测细胞在材料表面的平均黏附数量、扩展面积比、增殖能力和细胞周期的变化, 综合评价新型改性纳米复合材料的生物相容性和生物活性. 结果表明, 聚乳酸表面接枝改性可明显改善纳米生物玻璃粒子的团聚; PLGA中掺入一定比例的改性PLLA-g-BG可明显促进兔成骨细胞的黏附、扩展与增殖; 改性纳米生物玻璃的应用可提高生物可降解聚酯材料的生物相容性和生物活性.     

接枝丙烯酰胺改善聚乙烯膜表面亲水性的研究

利用等离子体技术和紫外照射接枝相结合在聚乙烯膜表面接枝丙烯酰胺(AAm)以改善其亲水性。通过衰减全反射红外光谱(ATR-FTIR)、X射线光电子能谱(XPS)和接触角测定验证了在无光引发剂的条件下,将等离子体预处理和紫外照射接枝结合起来可以有效地提高AAm的接枝效果,很好地改善PE膜表面的亲水性。探讨了等离子体复合参数W/(FM)、等离子体预处理时间、AAm单体浓度以及紫外照射时间对改善PE膜表面亲水性的影响,确定改善PE膜表面亲水性的最佳实验条件。     

成骨细胞在表面酰胺化聚乳酸膜上的黏附和增殖行为

利用紫外光接枝聚合丙烯酰胺(Acrylic amide, AAm)获得表面酰胺化的聚乳酸(PLA)膜, 并考察了成骨细胞在酰胺化表面的黏附和增殖行为. 结果表明, 酰胺基的引入改善了PLA膜的表面亲水性, 其表面水接触角由78°减少到56°, 自由能由42.7 mJ/m²增大到51.4 mJ/m²; 与对照组相比, 成骨细胞在改性表面培养3 d后有大量的丝状伪足伸出, 并且较快地进入了细胞分裂期, 表明PLA膜表面的酰胺化能够促进细胞的黏附和增殖.     

辐射接枝共聚合反应及其在有机生物医用材料制备中的应用

γ-射线辐射高分子材料表面接枝共聚合是一种绿色的、重要的有机生物材料合成制备方法. 综述了γ-射线辐射接枝共聚反应的原理、特点, 阐述了预辐射接枝共聚和共辐射接枝共聚的方法, 介绍了当前γ-射线辐射接枝共聚反应在改善有机生物医用材料的表面亲水性、生物相容性等方面的应用. 对辐射接枝共聚合制备功能药物载体研究进行了简要介绍.     

PLA大分子单体接枝NVP共聚物的合成与性能

制备了末端为双键的功能化聚乳酸大分子单体(PLA-HEMA),并以此大分子单体与N-乙烯基吡咯烷酮(NVP)进行自由基溶液共聚,合成了具有亲水性PVP-PHEMA主链和疏水性PLA支链的接枝共聚物。用FT-IR1、H-NMR、GPC、DSC、表面接触角测定研究了共聚物的结构与性能。结果表明:共聚物为非晶聚合物;NVP的摩尔投料量对共聚物的性能有显著影响,随NVP投料量增大,共聚物的分子量有所下降,玻璃化转变温度(Tg)增大;由于亲水性PVP和PHEMA链段的引入,共聚物的亲水性优于相应的线型聚乳酸材料。     

不饱和糖功能单体接枝聚氨酯膜的制备及其血液相容性

通过葡萄糖、丙烯酸羟乙酯和丁二胺反应,制备了含不饱和双键的糖基功能单体。 采用傅里叶红外光谱和核磁共振氢谱对合成的产物进行结构表征确定。 采用紫外光引发接枝聚合技术,将制备的不饱和糖单体接枝聚合到聚氨酯膜的表面,以衰减全反射模式下傅里叶红外光谱对表面接枝反应进行了确认。 通过静态水接触角实验和血小板黏附实验,分别对改性聚氨酯膜表面的亲水性和血液相容性进行了研究,结果表明,改性聚氨酯膜表面的接触角从86°降低到45°,血小板的粘附量由14.36×10³ cells/mm²减少到2.57×10³ cells/mm²,亲水性明显增强,血液相容性显著改善。     

紫外辐照接枝制备亲水性荷正电纳滤膜

通过在酚酞基聚芳醚酮超滤膜表面紫外辐照接枝亲水性单体二烯丙基二甲基氯化铵(DADMAC)制备了一种表面荷正电的纳滤膜. ATR-FTIR和表面水接触角的研究结果表明膜表面的接枝率和亲水性随着辐照时间和单体在接枝溶液中的浓度的增加而增加. 荷正电纳滤膜对盐溶液有很好的截留, 对盐溶液中的高价阳离子和低价阳离子的截留率分别为95%和65%. 但当溶液中存在高价负离子时, 膜的截留性能会明显下降. 表明静电效应在荷电纳滤膜的分离过程中起了重要的作用.     

p(HEMA-MMA)表面固定I-型胶原和碱性成纤维生长因子(bFGF)改善细胞相容性的研究

材料表面固定生物分子一直都被认为是其提高其细胞相容性有效的途径。本文采用羧基二咪唑(CDI)作为缩合剂,使p(HEMA-MMA)表面羟基与胶原中氨基发生缩合反应,从而将I-型胶原接枝在材料表面。然后利用"接枝-吸附"的方法,将I-型胶原和bFGF混合层吸附固定于材料表面,形成稳定的胶原与bFGF涂层。红外光谱(FTIR)和原子力显微镜(AFM)证实了该种固定方法的成功。静态接触角显示材料表面亲水性较改性前略微降低。涂层稳定性实验结果表明在类似人体环境(pH=7.4)下涂层具有良好的稳定性。细胞粘附性实验以及MTT实验一致显示改性后材料的细胞相容性得到明显提高。因此,Col/bFGF-p(HEMA-MMA)有望成为能够被宿主机体所接受的生物材料。     

Enhanced interlayer interaction in cellulose single nanofibre and poly(l-lactic acid) layered films by plasma-initiated surface grafting of poly(acrylic acid) onto poly(l-lactic acid) films

The surface of a poly(l-lactic acid) (PLLA) film was modified with poly(acrylic acid) (PAA) by plasma-initiated polymerization to increase the interaction between PLLA and cellulose single nanofibres (CSNF). The surface wettability of the PAA grafted PLLA film (PLLA-PAA film) was investigated by contact angle measurements. Modification of the PLLA film with PAA decreased the contact angle from 61° to 50°. The surface morphologies of the PLLA film, PLLA-PAA film and CSNF-coated PLLA-PAA film were studied by atomic force microscopy. The interaction between the CSNF and PLLA layers was strengthened by incorporation of a PAA layer onto the PLLA films and it is higher than 2N as proved by a peeling test. This is probably because the carboxyl groups of PAA form hydrogen bonds with the hydroxyl groups of CSNF.     

丙烯酸改性聚醚砜中空纤维渗透汽化膜的研究

采用自由基聚合反应制备了丙烯酸接枝改性的聚醚砜中空纤维渗透汽化膜,该膜用于醇／水分离获得了良好的效果。结果表明,通过改变聚合单体的浓度可以控制膜的接枝率,并调节膜的选择性和通量。改性膜的红外光谱和电镜分析结果表明：膜的接枝反应主要发生在中空纤维膜的内表面,膜的外表面接枝程度很低。力学性能测试表明接枝后膜的拉伸强度减弱。     

纳米羟基磷灰石表面接枝聚合左旋丙交酯

为了改善HA纳米粒子与有机PLGA的相容性,分别采用六亚甲基二异氰酸酯加乙二醇、左旋乳酸改性纳米粒子表面后或直接原位接枝聚合左旋丙交酯等3种不同方法,制备了表面修饰聚乳酸的纳米羟基磷灰石(PLLA-g-HA).FTIR、XPS、TEM、TGA测试表明PLLA成功接枝到HA的表面.其中六亚甲基二异氰酸酯加乙二醇改性HA纳米粒子所获得的PLLA接枝率远高于其它两种方法达25%,调整有机相和无机相的比例对PLLA接枝率的影响较小,其在氯仿中可以稳定分散2天以上.共混电纺丝后的拉伸测试表明PLLA-g-HA/PLAG复合纤维膜的力学性能高于HA/PLGA膜,当两者之间的比例为5%拉伸性能达到最大值.     

型胶原在聚-L-乳酸(PLLA)表面的化学接枝和涂层及其对软骨细胞生长的促进作用

采用接枝-涂层技术在聚-L-乳酸(PLLA)膜表面接枝聚甲基丙烯酸(PMAA)得到稳定的PLLA-g-PMAA胶原涂层.利用水溶性碳化二亚胺作为缩合剂,使PLLA-g-PMAA表面的羧基和胶原分子中的氨基发生缩合反应,从而将型胶原接枝在PLLA表面;同时保留材料表面物理涂层的胶原溶液,获得了稳定的胶原涂层.XPS谱图证实了接枝反应的发生.分别用比色法和茚三酮法测定了PLLA-g-PMAA表面的羧基密度和PLLA膜表面胶原的接枝量和涂层量.细胞培养结果表明,改性后的PLLA膜表面软骨细胞的铺展性能和增长速度明显改善.     

Crystallization kinetics study of poly(L‐lactic acid)/carbon nanotubes nanocomposites

Effects of carbon nanotubes (CNT) on the isothermal crystallization kinetics of poly(L ‐lactic acid) (PLLA) were quantitatively investigated using the Avrami equation and the secondary nucleation theory of Lauritzen and Hoffman. CNT via grafting modification with PLLA could well disperse in the PLLA matrix and give significantly enhanced crystallization rate and crystallinity of PLLA as analyzed by differential scanning calorimetry and polarized optical microscopy. Analysis of isothermal crystallization kinetics using the Avrami equation demonstrated that CNT significantly enhanced the bulk crystallization of PLLA. Analysis of spherulite growth kinetics using the secondary nucleation theory of Lauritzen and Hoffman found that CNT could expand the temperature range of the crystallization regime III of PLLA. Values of the nucleation constant (K_g) in crystallization regimes III and II of PLLA both increased with increasing CNT contents. The K_g III/K_g II ratios were found to be close to the theoretical value 2 but were not clearly found to depend on the CNT contents. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 983–989, 2010     

Grafting of poly(acrylic acid) onto nonporous glass bead surfaces

The surface of glass beads were modified with covalently bonded poly(acrylic acid). The optimum reaction conditions were determined to graft poly(acrylic acid) effectively onto the glass surface. The dependence of the graft polymer molecular weight, grafting percentage and monomer weight conversion based on these reaction conditions were consistent with free radical kinetics. Grafting efficiency for azobisisobutyronitrile was more complex compared with the benzyl peroxide initiator system © 1997 John Wiley & Sons, Ltd.     

聚砜与丙烯酸的紫外光辐射接枝共聚及其表征

在均相溶液体系下,运用紫外光辐射引发合成了聚砜与丙烯酸的接枝共聚物。用化学滴定、漫反射傅立叶变换红外光谱和热分析等技术对接枝聚合物进行了表征。结果表明:丙烯酸被接枝在聚砜链上;光照时间、单体浓度和光引发剂浓度对接枝率均有较大影响。膜表面接触角的研究表明,接枝共聚物膜的亲水性比改性前有所提高。     

Controlled functionalization of multiwalled carbon nanotubes with various molecular-weight poly(L-lactic acid)

Multiwalled carbon nanotubes (MWNT) were functionalized with poly(L-lactic acid) (PLLA) with different molecular weights using a "grafting to" technique. The oxidized MWNT (MWNT-COOH) were converted to the acyl-chloride-functionalized MWNT (MWNT-COCl) by treating them with thionyl chloride (SOCl2) and reacting them with PLLA to prepare the MWNT-g-PLLA. FTIR and Raman spectroscopy revealed that the PLLA was covalently attached to the MWNT, and the weight gain due to the functionalization was determined by thermogravimetric analyses (TGA). The Raman signals of the MWNT were greatly weakened as a result of the PLLA grafting. The morphology of the grafted PLLA was examined by using SEM and TEM. The amount of grafted PLLA depended on the molecular weight of the PLLA. The PLLA coated on the MWNT became thicker and more uniform with increasing PLLA molecular weight from 1000 to 3000. However, the amount of grafted PLLA became lower when the molecular weight of PLLA was further increased to 11,000 and 15,000, and the PLLA attached to the MWNT showed a squid leglike morphology forming blobs and leaving much of the MWNT surface bare.     

聚乙烯与丙烯酸的溶液接枝聚合

以过氧化苯甲酰为引发剂，二甲苯为溶剂，进行了丙烯酸与低密度聚乙烯的溶液接枝聚合，研究了ＢＰＯ用量、溶液浓度以及丙烯酸用量对接枝率的影响。聚乙烯接枝了丙烯酸后与铝的粘结强度显著增大，当接枝率为７．２％时，剥离强度由未接枝时的１９３Ｎ／ｍ，提高到９８４Ｎ／ｍ。     

Modification of porous silica particles with poly(acrylic acid)

The surface of porous silica particles was modified with poly(acrylic acid) by reacting the carboxyl groups on poly(acrylic acid) with the amino groups of pregrafted aminopropyltriethoxysilane (APS). The chemical modifications by APS and polymer were characterized by infrared spectroscopy and the amount of APS and poly(acrylic acid) grafted to the surface were determined by thermal gravimetric analyses. The wettability of the modified silica particles, based on the rate of water penetration, was pH‐dependent with PAA; at pH 1.5 the wettability increased but at pH 5.5 it decreased dramatically. The pore size and size distribution of the silica particles decreased with APS and polymer grafting. Copyright © 2000 John Wiley & Sons, Ltd.