含Gemini表面活性剂的PVA分散液晶的微结构与性能

采用N,N'-二(十二烷基)-N,N,N',N',N″-五甲基-1,4,7-三氮杂双碘化氨为Gemini表面活性剂,液晶为4-正戊基-4'-氰基联苯(5CB),通过微胶囊法制备了聚乙烯醇(PVA)分散液晶薄膜,着重研究Gemini表面活性剂对PVA分散液晶薄膜的微结构、电光特性的影响.结果表明,加入Gemini表面活性剂仅略微增加了PVA与5CB液晶的相容性,PVA分散液晶仍保持较高的相分离程度,但是Gemini表面活性剂使液晶微滴尺寸明显变小,液晶相均匀分散地于PVA基体中,液晶指向矢构型由两极型变化为径向型,PVA分散液晶薄膜的对比度和响应速度明显提高,同时保持较低的驱动电压.     

固化条件对聚合物分散液晶膜电光性能的影响

选用聚乙二醇二缩水甘油醚(EGDE)/季戊四醇缩水甘油醚(PERTGE)/1,8-二氨基-3,6-二氧杂辛烷(EDBEA)/向列相液晶(SLC1717)复合体系,在不同的固化条件下,通过热聚合诱导相分离方法制备了一系列电光性能不同的聚合物分散液晶(polymer dispersed liquid crystal,简称PDLC)膜.研究了固化温度和固化时间对制备的PDLC膜中聚合物网络的微观形貌和电光性能的影响.结果表明,随着固化温度的升高以及固化时间的缩短,PDLC膜的对比度、驱动电压和开态响应时间逐渐增大,而关态响应时间逐渐减小.在固化温度为363.2 K,固化时间为7 h时,所制备的PDLC膜具有较佳的电光性能.     

基于偶氮液晶的PDLC膜光调制研究

采用聚苯乙烯和光敏混合向列液晶(5CB＋BMAB), 通过溶剂引发相分离制备了聚合物分散液晶膜(PDLC). 利用偶氮液晶的光致相变, 实现了聚合物分散液晶薄膜的光控开关. 实验结果表明, 在PDLC膜内部液晶微球中, 液晶分子呈双极形分布. 其光控温度区间19～36 ℃之间. 以360 nm附近紫外光照射之后, PDLC膜的最大透光率从6%增加到93%. 在相同的工作距离下, 光调制的时间与PDLC膜内部微孔直径相关. 在相同的液晶浓度下, 直径越小, 调制时间越长.     

丙烯酸酯/液晶体系的光聚合反应动力学对PDLC电光性质的影响

采用光-示差扫描量热法(P-DSC)和光-流变学(P-Rheology)技术,测定了丙烯酸酯/液晶体系的光聚合反应动力学和凝胶化时间.基于自催化模型和凝胶时间-温度关系,计算了体系的光聚合反应速率常数和活化能,探讨了单体结构与组成、反应温度对体系光聚合动力学的影响,并研究了聚合物分散液晶(PDLC)的电光响应行为与相分离结构对光聚合动力学的依赖性.结果表明,升高反应温度、增加体系的单体反应活性和平均官能度,均提高了体系的光聚合速率常数,缩短了光聚合凝胶时间.随着单体反应活性和平均官能度的提高,体系的光聚合反应活化能明显降低,且凝胶化前的光聚合反应活化能低于光聚合全过程的平均反应活化能.当液晶含量为50%时,形成的PDLC呈亚微米尺度的双连续相结构.随着光聚合反应温度的升高,光聚合速率加快,导致凝胶时间缩短、相分离程度降低,使PDLC中液晶相尺寸变小、聚合物网络致密化,PDLC的弛豫时间延长、饱和电压降低,而开启时间和阈值电压变化不大.     

多官能Iniferter制备聚合物分散液晶膜及其含量对电光性能的影响

采用可逆加成-断裂链转移(RAFT)、引发转移终止(Iniferter)活性自由基聚合法分步骤制备多官能Iniferter的大分子(RAFT-MI),并通过紫外光聚合诱导相分离法制备接枝共聚物为基体的聚合物分散液晶(PDLC)膜,研究了不同含量的RAFT-MI对PDLC膜的微观形貌、开态透光率、阈值电压(Vth)、饱和电压(Vsat)、对比度和记忆效应的影响.结果表明,当PDLC中的RAFT-MI含量从10%增加到30%时,开态透光率先增加,随后又逐渐降低,而Vth、Vsat逐渐降低,对比度先增加,然后又降低,记忆效应减弱.     

大分子引发剂分子量对接枝聚合物基体的PDLC电光性能的影响

以可逆加成-断裂链转移(RAFT)、引发转移终止(iniferter)活性自由基聚合相结合的方法,用一步法制备了不同分子量的大分子引发剂RAFT-PS-co-PCMSI(MI),并通过紫外光聚合诱导相分离法制备了以接枝聚合物为基体的聚合物分散液晶(PDLC)膜.研究了不同分子量的MI对PDLC的微观形貌,关闭状态透光率,阈值电压,饱和电压以及记忆效应等方面的影响.研究表明,降低PDLC中MI的分子量,会使得液晶微滴粒径增大,阈值电压(Vth)、饱和电压(Vsat)减小,记忆效应、关闭状态透光率升高.     

松果状纳米氧化铁对液晶电光性能的影响

液晶材料被广泛应用于液晶显示器(LCD)中,但是由于液晶中杂质的存在,导致液晶的应用电压变大,增加了能耗。 为了降低应用中的阈值电压和饱和电压,通常向液晶中添加纳米颗粒来提高电光性能。 本文采用简单的化学沉淀法制备了形貌均一,大小尺寸均匀的松果状氧化铁(P-Fe₂O₃)纳米颗粒。 将其掺杂到向列相液晶4-氰基-4'-戊基联苯(4-cyano-4'-pentylbiphenyl,5CB)中,结果表明,掺杂质量分数为0.5%时,电光性能达到最优,阈值电压和饱和电压分别降低24.8%和45.2%,对比度增大46%,响应时间降低至17.6 ms,此性能优于相同条件下掺杂普通Fe₂O₃纳米颗粒的向列相液晶5CB,其阈值电压和饱和电压分别降低15%和16%。 这归因于松果状Fe₂O₃纳米颗粒可以在向列相液晶5CB中均匀分散,其粗糙的表面吸附了液晶中的杂质离子,减少了杂质离子的屏蔽效应,从而提高了电光性能。     

PDLC的形态结构和光电性能

PDLC(Polymer Dispersed Liquid Crystal)是把向列型液晶以微小粒子的方式分散在高分子基质中形成膜,而具有独特性质的一种新型电光显示器件。本文对影响PDLC形态结构的因素和控制方法, PDLC的工作原理以及电光性质作了较为详细的概述。     

聚合物分散液晶(PDLC)材料的光聚合反应

以Ar+激光器为光源, 采用虎红、 N-苯基甘氨酸、二季戊四醇羟基五丙烯酸酯和乙烯基吡咯烷酮分别作为光引发剂、共引发剂、预聚物和稀释剂, 与液晶材料TEB30A结合, 通过光聚合反应, 制备了聚合物分散液晶(PDLC), 用紫外光谱和荧光光谱对其反应机理进行了分析. 实验结果表明, PDLC是通过光引发剂吸收光子能量后与共引发剂相互作用, 形成自由基中间体并引发聚合反应, 使预聚物与液晶产生相分离形成的.     

环氧树脂基高分子分散液晶材料相分离过程的研究

根据高分子分散液晶材料在相分离过程中透光率的变化,研究了高分子分散液晶材料相分离过程与液晶浓度、温度的关系,观察到相分离过程中的周期性的起伏现象．对相分离过程与高分子分散液晶材料的电光性能作了初步探讨     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.