A numerical analysis of cracks emanating from an elliptical hole in a 2-D elasticity plate

This paper is concerned with the stress intensity factors (SIFs) of cracks emanating from an elliptical hole in an infinite or a finite plate under biaxial loads by using a boundary element method, which consists of the non-singular displacement discontinuity element presented by Crouch and Starfield and the crack-tip displacement discontinuity elements due to the author. In the boundary element implementation the left or the right crack-tip element is placed locally at the corresponding left or right crack tip on top of the constant displacement discontinuity elements that cover the entire crack surface and the other boundaries. A few numerical examples are included to show that the present approach is very efficient and accurate for the calculating the SIFs of crack problems in an infinite or a finite plate. The present numerical results of cracks emanating from an elliptical hole under biaxial loads can reveal the effect of the elliptical aspect ratio and the transverse load on the SIFs.     

Scattering of SH-wave by cracks originating at an elliptic hole and dynamic stress intensity factor

The method of complex function and the method of Green‘s function are used to investigate the problem of SH-wave scattering by radial cracks of any limited length along the radius originating at the boundary of an elliptical hole, and the solution of dynamicstress intensity factor at the crack tip was given. A Green‘s function was constructed for the problem, which is a basic solution of displacement field for an elastic half space containing a half elliptical gap impacted by anti-plane harmonic linear source force at any point of its horizontal boundary. With division of a crack technique, a series of integral equations can be established on the conditions of continuity and the solution of dynamic stress intensity factor can be obtained. The influence of an elliptical hole on the dynamic stress intensity factor at the crack tip was discussed.     

含有非圆形双孔的无限平板中应力的解析解研究

无限平板中含有任意形状单个孔的问题可以使用复变函数方法获得其应力解析解.对于无限平板中含有两个圆孔或两个椭圆孔的双连通域问题,也可以利用多种方法进行求解,比如双极坐标法、应力函数法、复变函数法以及施瓦茨交替法等.其中复变函数中的保角变换方法是获得应力解析解的一个重要方法.但目前尚未见到用此方法求解无限板中含有一个正方形孔和一个椭圆孔的问题.当板在无穷远处受有均布载荷和孔边作用垂直均布压力时,利用保角变换方法可以求解板中含有两个特定形状孔的问题.该方法将所讨论的区域映射成象平面里的一个圆环,其中最关键的一步是找出相应的映射函数.基于黎曼映射定理,提出了该映射函数一般形式,并利用最优化方法,找到了该问题的具体映射函数,然后通过孔边应力边界条件建立了求解两个解析函数的基本方程,获得了该问题的应力解析解.运用ANSYS有限单元法与结果进行了对比.研究了孔距、椭圆形孔大小和两孔布置方位对边界切向应力的影响,以及不同载荷下两孔中心线上应力分布规律.      

The mode III cracks emanating from an elliptical hole in the piezo-electro-magneto-elastic materials

The mode III crack problem in a medium possessing coupled electro-magneto-elastic is considered. Two asymmetrical edge cracks emanate from an elliptical hole. Combined stress, electric and magnetic loads are considered. The elliptical hole and cracks are assumed to be either magneto-electrically impermeable or permeable. The closed-form solution for stress, electric and magnetic intensity factors are derived explicitly. Also the solution for energy release rate is given in closed form. The solution is based on the complex variable method combined with the method of conformal mapping. Numerical computations are given to illustrate the effect of variable geometrical and material parameters on stress, electric and magnetic intensity factors and energy release rate.     

Boundary element analysis of crack problems in functionally graded materials

The present study examines the crack problems in a functionally graded material (FGM) whose upper and bottom surfaces are fully bonded with dissimilar homogeneous materials. A so-called generalized Kelvin solution based boundary element method is used in the numerical examination. The multi-region method and the eight-node traction-singular boundary elements are used for the crack evaluation. The layer discretization technique is utilized to approximate the depth material non-homogeneity of the FGM layer. The proposed method can deal with any depth variations in both the shear modulus and the Poisson ratio of the FGMs. Results of the present analysis are compared very well with the exact analytical solutions available in the literature, which demonstrates that the proposed method can accurately evaluate the stress intensity factors (SIFs) for cracks in FGMs. The paper further evaluates the effect of the functionally graded variations in the Poisson ratio on the stress intensity factors. The paper also assesses the elliptical cracks in the FGM system. The paper presents the influence of both the non-homogeneity and the thickness of the FGM layer on the three SIFs associated with the elliptical cracks.     

一维正方准晶椭圆孔口平面弹性问题的解析解

利用复变方法,引入广义保角映射,研究了一维正方准晶中具有椭圆孔口的平面弹性问题,给出了各应力分量的复变表示,并在特殊情况下转化为Griffith裂纹,得到该裂纹尖端处的应力强度因子的解析解.当准晶体的对称性增加时,正方准晶椭圆孔口平面弹性问题退化为一维四方准晶中具有椭圆孔口的平面弹性问题,同样在特殊情况下转化为Griffith裂纹,得到裂纹尖端处的应力强度因子的解析解.     

The thermoelastic equilibrium of a transversally isotropic medium with an elliptic crack under symmetric loading

The stress intensity factors (SIFs) are evaluated for flat elliptical cracks located in a transversally isotropic material (cracks are assumed perpendicular to the transtropy axis) under an arbitrary load and symmetric temperature. The SIFs for an elliptical crack in a transversally isotropic medium are determined using the formulas (derived by the author in his previous studies) of transition from an isotropic to transversally isotropic material and the relative problem for an isotropic medium. It is proved that these formulas can be employed for an arbitrary homogeneous transversally isotropic material (no matter whether the roots of some characteristic equation of the material are real or complex) with an arbitrary flat crack or a system of coplanar flat cracks, including elliptical ones, under an arbitrary load and symmetric temperature. A transversally isotropic material with two coplanar elliptical cracks is considered as an illustrative example. The dependences of the SIFs on the parameters of cracks and their arrangement at a decreasing temperature are presented. S. P. Timoshenko Institute of Mechanics, National Academy of Sciences of Ukraine Kiev. Translated from Prikladnaya Mekhanika, Vol. 36, No. 4, pp. 96–105, April, 2000.     

带裂纹的椭圆孔口问题的应力分析

断裂现象与材料和结构中的孔洞、缺口或裂纹等缺陷密切相关,这是因为缺陷附近的应力集中明显.该文利用复变方法,通过保角映射研究了带裂纹的椭圆孔洞的平面弹性问题,给出了应力强度因子的解析解.并由此计算了两互相垂直的裂纹问题.     

估算裂纹应力强度因子的新方法

根据裂纹形状与裂纹尖端应力强度因子分布之间的固有关系,在线弹性断 裂力学条件下,提出了一种按已知I型裂纹应力强度因子分布规律求裂纹形状及相应应力强 度因子的无梯度迭代法. 通过有限厚度、有限宽度板穿透裂纹和表面裂纹的数值模拟实例验 证了所提出方法的有效性和实用性,并对不同应力强度因子分布规律对裂纹形状以及相应的 应力强度因子大小的影响进行了分析和讨论. 所提出的方法有助于提高实际扩展裂纹应 力强度因子的估算精度以及更合理地预测疲劳裂纹形状演化.     

Surface tension-induced stress concentration around an elliptical hole in an anisotropic half-plane

We examine the surface tension-induced stress concentration around an elliptical hole inside an anisotropic half-plane with traction-free surface. Using conformal mapping techniques, the corresponding complex potential in the half-plane is expressed in a series whose unknown coefficients are determined numerically. Our results indicate that the maximum hoop stress around the hole (which appears in the vicinity of the point of maximum curvature) increases rapidly with decreasing distance between the hole and the free surface. In particular, for an elliptical or even circular hole in an anisotropic half-plane we find that, with decreasing distance between the hole and the free surface, the hoop stress can switch from compressive to tensile at certain points on the hole's boundary and from tensile to compressive at others. This phenomenon is absent in the case of an elliptical or even circular hole in the corresponding case of an isotropic half-plane.     

内部压力作用下矩形板中源于椭圆孔的分支裂纹应力强度因子的一种数值分析

应用一种边界元方法来研究内部压力作用下矩形板中源于椭圆孔的分支裂纹。该边界元方法由Crouch与Starfied建立的常位移不连续单元和笔者最近提出的裂尖位移不连续单元构成。在该边界元方法的实施过程中,左、右裂尖位移不连续单元分别置于裂纹的左、右裂尖处,而常位移不连续单元则分布于除了裂尖位移不连续单元占据的位置之外的整个裂纹面及其它边界。本数值结果进一步证实这种数值方法对计算有限大板中复杂裂纹的应力强度因子的有效性,同时该数值结果可以揭示裂纹体几何对应力强度因子的影响。     

General solutions of plane problem for power function curved cracks

A new exact and universal conformal mapping is proposed. Using Muskhelishvili's complex potential method, the plane elasticity problem of power function curved cracks is investigated with an arbitrary power of a natural number, and the general solutions of the stress intensity factors (SIFs) for mode I and mode II at the crack tip are obtained under the remotely uniform tensile loads. The present results can be reduced to the well-known solutions when the power of the function takes different natural numbers. Numerical examples are conducted to reveal the effects of the coefficient, the power, and the projected length along the x-axis of the power function curved crack on the SIFs for mode I and mode II.     

拉伸载荷作用下单边缺陷-边裂纹应力强度因子研究

利用杂交位移不连续法研究拉伸载荷作用下矩形板中单边缺陷-边裂纹(半圆孔裂纹和半方孔裂纹)问题,给出了这三种平面弹性裂纹问题的应力强度因子的详细数值解。通过半圆孔裂纹问题和半方孔裂纹问题与单边裂纹问题的应力强度因子的比较,发现半圆孔和半方孔对单边裂纹有屏蔽影响。此外,本文的研究结果表明,杂交位移不连续法用于分析平面弹性有限体中复杂裂纹问题的应力强度因子简单且又准确。     

Stress intensity factors of a plate with two cracks emanating from an arbitrary hole

In this paper, Muskhelishvili complex function theory and boundary collocation method are used to calculate the stress intensity factors (SIF) of a plate with two cracks emanating from an arbitrary hole. The calculated examples include a circular, elliptical, rectangular, or rhombic hole in a plate. The principle and procedure by the method is not only rather simple, but also has good accuracy. The SIF values calculated compare very favorably with the existing solutions. At the same time,the method can be used for different finite plate with two cracks emanating from a hole with more complex geometrical and loading conditions. It is an effective unified approach for this kind of fracture problems.     

Green's function of a point dislocation for the bending of a composite infinite plate with an elliptical hole at interface

Summary  The problem of a hole at bimaterial interface is of practical importance in providing a good understanding of the debonding phenomenon and for determining factors that affect the mechanical properties of composite elements of structures. The problem of a point dislocation in bending bonded dissimilar semi-infinite plates with an elliptical hole at interface is tackled in this paper. Based on the method of analytic continuation and the rational mapping function technique, the problem of obtaining the stress functions in the upper and lower plates is decoupled, and reduced to two Riemann–Hilbert problems. The closed-form solution is obtained. The stress distributions at the bimaterial interface, as well as the debonding at both vertices of the elliptical hole are studied. The stress intensities of debonding are depicted for various parameters. Received 16 March 2000; accepted for publication 12 July 2000     

Closed form solution of stress intensity factors for cracks emanating from surface semi-spherical cavity in finite body with energy release rate method

In this paper, a new semi-analytical and semi-engineering method of the closed form solution of stress intensity factors (SIFs) of cracks emanating from a surface semi-spherical cavity in a finite body is derived using the energy release rate theory. A mode of crack opening displacements of a normal slice is established, and the normal slice relevant functions are introduced. The proposed method is both effective and accurate for the problem of three-dimensional cracks emanating from a surface cavity. A series of useful results of SIFs are obtained.     

Minimizing stress concentrations around an elliptical hole by concentrated forces acting on the uniaxially loaded plate

When concentrated forces are applied at any points of the outer region of an ellipse in an infinite plate, the complex potentials are determined using the conformal mapping method and Cauchy's integral formula. And then, based on the superposition principle, the analytical solutions for stress around an elliptical hole in an infinite plate subjected to a uniform far-field stress and concentrated forces, are obtained. Tangential stress concentration will occur on the hole boundary when only far-field uniform loads are applied. When concentrated forces are applied in the reversed directions of the uniform loads, tangential stress concentration on the hole boundary can be released significantly. In order to minimize the tangential stress concentration, we need to determine the optimum positions and values of the concentrated forces. Three different optimization methods are applied to achieve this aim. The results show that the tangential stress can be released significantly when the optimized concentrated forces are applied.     

Comprehensive investigation of stress intensity factors in rotating disks containing three-dimensional semi-elliptical cracks

Initiation and propagation of cracks in rotating disks may cause catastrophic failures. Therefore, determination of fracture parameters under different working conditions is an essential issue. In this paper, a comprehensive study of stress intensity factors(SIFs) in rotating disks containing three-dimensional(3D) semi-elliptical cracks subjected to different working conditions is carried out. The effects of mechanical properties, rotational velocity, and orientation of cracks on SIFs in rotating disks under centrifugal loading are investigated. Also, the effects of using composite patches to reduce SIFs in rotating disks are studied. The effects of patching design variables such as mechanical properties, thickness, and ply angle are investigated separately. The modeling and analytical procedure are verified in comparison with previously reported results in the literature.     

A numerical analysis of cracks emanating from a surface elliptical hole in infinite body in tension

This paper deals with such a kind of surface crack problem with an approximately same depth, which is called a liked-plane crack problem. Based on the previous investigations on internal rectangular crack and surface rectangular crack in infinite solid in tension and a hybrid displacement discontinuity method (a boundary element method) proposed recently by Yan, a numerical approach for the liked-plane crack problem in hand is presented. Numerical examples are given to illustrate the numerical approach is simple, yet accurate for calculating the SIFs of a liked-plane crack. Specifically, a pair of cracks emanating from a surface elliptical hole in infinite body in tension are investigated in detail.     

带双裂纹的椭圆孔口问题的应力分析

利用复变方法,通过构造新的保角映射,研究了带双裂纹椭圆孔口的平面弹性问 题,得到了I型与II型裂纹问题应力强度因子的解析解.在极限情形下, 不仅可以还原经典的Griffith裂纹的结果,而且可模拟出十字裂纹和带双裂纹的圆 形孔口问题.