Sol–gel preparation and electrochemical performances of LiFe1/3Mn1/3Co1/3PO4/C composites with core–shell nanostructure

LiFe_1/3Mn_1/3Co_1/3PO₄/C solid solution was prepared via a poly(ethylene glycol) assisted sol–gel method and exploited as cathode materials for lithium ion batteries. X-ray diffraction patterns indicate that LiFe_1/3Mn_1/3Co_1/3PO₄/C is crystallized in an orthorhombic structure. The scanning electron microscopy and transmission electron microscopy show that the particles are about 200 nm with a uniform carbon coating of about 8 nm in thickness to form a core–shell nanostructure. During charge–discharge cycles, LiFe_1/3Mn_1/3Co_1/3PO₄/C presented three plateaus corresponding to Fe³⁺/Fe²⁺, Mn³⁺/Mn²⁺ and Co³⁺/Co²⁺ redox couples, and a discharge capacity of 150.8 mAh g^?1 in the first cycle, remaining 121.2 mAh g^?1 after 30 cycles. Core–shell structure can optimize the performances of polyoxoanionic materials for lithium ion batteries.     

A novel synthetic route for LiFePO_4/C cathode materials by addition of starch for lithium-ion batteries

LiFePO4/Carbon composite cathode material was prepared using starch as carbon source by spray-pelleting and subsequent pyrolysis in N2. The samples were characterized by XRD, SEM, Raman, and their electrochemical performance was investigated in terms of cycling behavior. There has a special micro-morphology via the process, which is favorable to electrochemical properties. The discharge capacity of the LiFePO4.C composite was 170 mAh g-1, equal to the theoretical specific capacity at 0.1 C rate. At 4 C current density, the specific capacity was about 80 mAh g-1, which can satisfy for transportation applications if having a more flat discharge flat.     

Synthesis of Li3Ni x V2−x (PO4)3/C cathode materials and their electrochemical performance for lithium ion batteries

Li₃Ni _x V_2?x (PO₄)₃/C (x?=?0, 0.02, 0.04 and 0.06) samples have been synthesized via an improved sol–gel method. X-ray diffraction patterns indicate that the structure of the prepared samples retains monoclinic, and the single phase has not been changed with Ni doping. From the analysis of electrochemical performance, the Li₃Ni_0.04?V_1.96(PO₄)₃/C sample exhibits the best electrochemical property. It delivers a discharge capacity of 112.1 mAh?g^?1 with capacity retention of 95.2 % over 300 cycles at 10 C rate in the range of 3.0–4.8 V; cyclic voltammetry and electrochemical impedance spectra testing further prove that the electrochemical reversibility and lithium ion diffusion behavior of Li₃V₂(PO₄)₃ have also been effectively improved through Ni doping.     

Sol–gel preparation and electrochemical properties of La-doped Li4Ti5O12 anode material for lithium-ion battery

A sol–gel method using Ti(OC₄H₉)₄, LiCH₃COO·2H₂O, and La(NO₃)₃·6H₂O as starting materials and ethyl acetoacetate as chelating agent to prepare pure and lanthanum (La)-doped Li₄Ti₅O₁₂ is reported. The structure and morphology of the active materials characterized by powder X-ray diffraction and scanning electron microscopy analysis indicate that doping with a certain amount of La³⁺ does not affect the structure of Li₄Ti₅O₁₂, but can restrain the agglomeration of the particles during heat treatment. The electrochemical properties measured by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge cycling tests show that La-doped Li₄Ti₅O₁₂ presents a much improved electrochemical performance due to a decrease in charge transfer resistance. At current densities of 1 and 5 C, the La-doped Li₄Ti₅O₁₂ exhibits excellent reversible capacities of 156.16 and 150.79 mAh?g^?1, respectively. The excellent rate capability and good cycling performance make La-doped Li₄Ti₅O₁₂ a promising anode material for lithium-ion batteries in energy storage systems.     

Structural and electrochemical characterization of vanadium-excess Li3V2(PO4)3-LiVOPO4/C composite cathode material synthesized by sol–gel method

Journal of Solid State Electrochemistry - To improve capacity and electrochemical performance of the cathode of Li-ion batteries, non-stoichiometric, vanadium-excess (V-excess)...     

Electrospinning of GeO_2–C fibers and electrochemical application in lithium-ion batteries

GeO_2–C fibers were successfully synthesized using electrospinning homogeneous sol and subsequent calcination in an inert atmosphere. The spinnable sol was prepared by adding polyacrylonitrile(PAN)and polyvinylpyrrolidone(PVP) in a weight ratio of 1:1 into a mixture with white precipitate produced by dropping GeCl_4 into DMF. X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS),thermogravimetric analysis(TGA), scanning electron microscopy(SEM) and transmission electron microscopy(TEM) were employed to characterize the as-obtained fibers, and electrochemical tests were conducted to measure electrochemical performance of the electrode. The electrospun fibers have uniform diameters of 300 nm. After being calcined at 600 8C for 2 h in Ar, they transform to amorphous GeO_2–C fibers with the same morphologies. The Ge O_2–C fibers exhibit excellent cycling stability with a high reversible capacity of 838.93 m A h g~(-1)after 100 cycles at a current density of 50 m A g~(-1), indicating the composite fibers could be promising anode candidates for lithium-ion batteries.     

Synthesis and characterization of LiMn0.8Fe0.2PO4/rGO/C for lithium-ion batteries via in-situ coating of Mn0.8Fe0.2C2O4·2H2O precursor with graphene oxide

Journal of Solid State Electrochemistry - LiMn0.8Fe0.2PO4 is a potential candidate cathode material to balance the energy density, safety, and cost of power lithium ion batteries. However, the low...     

Effects of oxygen vacancy on the electrochemical properties of γ-V2O5 as cathode material for lithium-ion batteries: a first-principle study

Generating oxygen vacancies is an effective way to improve the lithium-ion storage performance of V₂O₅. However, the mechanism has not been theoretically investigated. In this study, first-principle calculations were performed to study the effect of oxygen vacancy on electrochemical properties of γ-V₂O₅ as cathode material for lithium-ion batteries. γ-V₂O₅ with oxygen vacancy mole fraction of 1.67% shows an open circuit voltage about 0.1 V lower than that of the perfect γ-V₂O₅. Oxygen vacancies generates gap states, which is beneficial to the electronic conductivity of γ-V₂O₅ and γ-LiV₂O₅. In addition, the activation energies for lithium-ion diffusion along [010] in both γ-V₂O₅ and γ-LiV₂O₅ are increased by oxygen vacancy, which might lead to the decrease of diffusion coefficient. Our results will provide guidance for further improving the lithium-ion storage performance of γ-V₂O₅.

     

Capacity of layered cathode materials for lithium-ion batteries — a theoretical study and experimental evaluation

The theoretical capacity and the vacancy concentration of metal-ion-doped layered compounds such as LiCoO₂, LiNiO₂, and LiMnO₂, acting as cathodes in high-voltage lithium-ion batteries are calculated. The capacity shows strong dependence on valency of the doped metal ion and vacancy concentration. Experimental verification carried out to check the validity of the proposed equation for aluminium substitution into the potential layered materials shows good agreement between the experimental and theoretical capacity values. The vacancy concentration values of doped layered compounds have been found to be high when compared with that of the doped spinel compounds.     

Synthesis and electrochemical properties of Li9V3 − x Ti x (P2O7)3(PO4)2/C compounds via wet method for lithium-ion batteries

A series of Ti⁴⁺-doped Li₉V_3???x Ti _x (P₂O₇)₃(PO₄)₂/C compounds have been prepared by using wet method. X-ray diffraction measurement shows that single phase region can be expressed as x?≤?0.10. The effects of substitution of Ti for V on the electrochemical properties of Li₉V_3???x Ti _x (P₂O₇)₃(PO₄)₂ compounds have been studied. Our investigations show that Ti doping can improve the electrochemical performance. The Li₉V_2.95Ti_0.05(P₂O₇)₃(PO₄)₂/C exhibits the best cycle performance and the highest first discharge capacity of 120.7 mAh g^?1 at 0.2 C. The electrochemical impedance spectroscopy indicates that the charge transfer resistance initially decreases with x and then for x?>?0.05 increases monotonically with Ti⁴⁺ content.     

Synthesis and electrochemical performance of CeO2@CNTs/S composite cathode for Li–S batteries

The shuttle effect of lithium-sulfur (Li–S) battery is one of the crucial factors restraining its commercial application, because LiPSs (lithium polysulfides) usually leads to poor cycle life and low coulomb efficiency. Some studies have shown that metal oxides can adsorb soluble polysulfides. Herein, CeO₂ (cerium-oxide)-doped carbon nanotubes (CeO₂@CNTs) were prepared by the hydrothermal method. The polar metal oxide CeO₂ enhanced the chemisorption of the cathode to LiPSs and promoted the redox reaction of the cathode through catalysis properties. Meanwhile, the carbon nanotubes (CNTs) enhanced cathode conductivity and achieved more sulfur loading. The strategy could alleviate polysulfide shuttling and accelerate redox kinetics, improving Li–S batteries' electrochemical performances. As a result, the CeO₂@CNTs/S composite cathode showed the excellent capacity of 1437.6 mAh g⁻¹ in the current density of 167.5 mA g⁻¹ at 0.1 C, as well as a long-term cyclability with an inferior capacity decay of 0.17% per cycle and a superhigh coulombic efficiency of 100.434% within 300 cycles. The superior electrochemical performance was attributed to the polar adsorption of CeO₂ on polysulfides and the excellent conductivity of CNTs.

     

Nanostructured and nanoporous LiFePO4 and LiNi0.5Mn1.5O4-δ as cathode materials for lithium-ion batteries

Recent developments in the synthesis of nanostructured cathode materials are reviewed for the two prominent compounds LiFePO₄ and LiNi_0.5Mn_1.5O₄, and own results on LiFePO₄ and LiNi_0.5Mn_1.5O₄ with different microstructure are presented. The synthesis of LiFePO₄ composites with porous carbons and the scale up of their synthesis is reported, as well as of nanoporous materials. In the case of LiNi_0.5Mn_1.5O₄ the formation of deteriorating cathode surface films is studied with thin film electrodes and ToF-SIMS depth profiling.     

Synthesis and electrochemical performance of sulfur–carbon composite cathode for lithium–sulfur batteries

In this paper, porous carbon was synthesized by an activation method, with phenolic resin as carbon source and nanometer calcium carbonate as activating agent. Sulfur–porous carbon composite material was prepared by thermally treating a mixture of sublimed sulfur and porous carbon. Morphology and electrochemical performance of the carbon and sulfur–carbon composite cathode were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectra (EIS), and galvanostatic charge–discharge test. The composite containing 39 wt.% sulfur obtained an initial discharge capacity of about 1,130 mA?h g^?1 under the current density of 80 mA?g^?1 and presented a long electrochemical stability up to 100 cycles.     

V2O3/C composite fabricated by carboxylic acid-assisted sol–gel synthesis as anode material for lithium-ion batteries

Journal of Sol-Gel Science and Technology - The potential battery electrode material V2O3/C has been prepared using a sol–gel thermolysis technique, employing vanadyl hydroxide as precursor...     

Improved electrochemical properties of chromium substituted in LiCr1 ? x Ni x O2 cathode materials for rechargeable lithium-ion batteries

Pristine- and chromium-substituted LiNiO₂ nanoparticles were synthesized by sol-gel method using nitrate precursor at 800?°C for 12?h. Physical properties of the synthesized product were analyzed using Fourier transform infrared, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive analysis X-ray. XRD studies revealed a well-defined layer structure and a linear variation of lattice parameters with the addition of chromium and no impurities. Surface morphology and particle size of synthesized materials were changed with chromium addition using SEM and TEM analyses. Assembled lithium-ion cells were evaluated for charge/discharge studies at different rates, cyclic voltammetry, and electrochemical impedance spectra. The initial discharge capacity of LiNiO₂ cathode material was found to be 168?mA hg^?1; however, discharge capacity increased in chromium substitution. Electrochemical impedance spectroscopy revealed that LiCr_0.10Ni_0.90O₂ could enhance charge transfer resistance upon cycling. The substitution of Ni with chromium, LiCr_0.10Ni_0.90O₂, had better cycle life, low irreversible capacity, and excellent electrochemical performance.     

Electrodeposition and electrochemical properties of novel ternary tin–cobalt–phosphorus alloy electrodes for lithium-ion batteries

Porous Sn–Co–P alloy with reticular structure were prepared by electroplating using copper foam as current collector. The structure and electrochemical performance of the electroplated porous Sn–Co–P alloy electrodes were investigated in detail. Experimental results illustrated that the porous Sn–Co–P alloy consists of mainly SnP_0.94 phase with a minor quantity of Sn and Co₃Sn₂. Galvanostatic charge–discharge tests of porous Sn–Co–P alloy electrodes confirmed its excellent performances: at 50th charge–discharge cycle, the discharge specific capacity is 503 mAh g^?1 and the columbic efficiency is as high as 99%. It has revealed that the porous and multi-phase composite structure of the alloy can restrain the pulverization of electrode in charge/discharge cycles, and accommodate partly the volume expansion and phase transition, resulting in good cycleability of the electrode.     

Comparison of structure and electrochemical properties for 5 V LiNi0.5Mn1.5O4 and LiNi0.4Cr0.2Mn1.4O4 cathode materials

Spinel LiNi_0.5Mn_1.5O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials have been successfully synthesized by the sol–gel method using citric acid as a chelating agent. The structure and electrochemical performance of these as-prepared powders have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and the galvanostatic charge–discharge test in detail. XRD results show that there is a small Li _y Ni_1-y O impurity peak placed close to the (4 0 0) line of the spinel LiNi_0.5Mn_1.5O₄, and LiMn_1.4Cr_0.2Ni_0.4O₄ has high phase purity, and the powders are well crystallized. SEM indicates that LiMn_1.4Cr_0.2Ni_0.4O₄ has a slightly smaller particle size and a more regular morphological structure with narrow size distribution than those of LiNi_0.5Mn_1.5O₄. Galvanostatic charge–discharge testing indicates that the initial discharge capacities of LiMn_1.4Cr_0.2Ni_0.4O₄ and LiNi_0.5Mn_1.5O₄ cycled at 0.15 C are 129.6 and 130.2 mAh g⁻¹, respectively, and the capacity losses compared to the initial value, after 50 cycles, are 2.09% and 5.68%, respectively. LiMn_1.4Cr_0.2Ni_0.4O₄ cathode has a higher electrode coulombic efficiency than that of the LiNi_0.5Mn_1.5O₄ cathode, implying that Ni and Cr dual substitution is beneficial to the reversible intercalation and de-intercalation of Li⁺.     

Synthesis and electrochemical performance of TiO2–sulfur composite cathode materials for lithium–sulfur batteries

Titania–sulfur (TiO₂–S) composite cathode materials were synthesized for lithium–sulfur batteries. The composites were characterized and examined by X-ray diffraction, nitrogen adsorption/desorption measurements, scanning electron microscopy, and electrochemical methods, such as cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. It is found that the mesoporous TiO₂ and sulfur particles are uniformly distributed in the composite after a melt-diffusion process. When evaluating the electrochemical properties of as-prepared TiO₂–S composite as cathode materials in lithium–sulfur batteries, it exhibits much improved cyclical stability and high rate performance. The results showed that an initial discharge specific capacity of 1,460 mAh/g at 0.2 C and capacity retention ratio of 46.6 % over 100 cycles of composite cathode, which are higher than that of pristine sulfur. The improvements of electrochemical performances were due to the good dispersion of sulfur in the pores of TiO₂ particles and the excellent adsorbing effect on polysulfides of TiO₂.