可调谐锁模脉冲环形腔掺铒光纤激光器

报道了一种结构简单、波长稳定可调的被动锁模环形腔掺铒光纤激光器.利用非线性偏振旋转效应作为等效可饱和吸收体实现自起振被动锁模,通过使用光纤偏振控制器和偏振相关光隔离器作为波长调谐器件,在输出端使用输出耦合器为工作波长在1550±50 nm的宽带耦合器,实现了光纤激光器的输出锁模脉冲激光中心波长较宽范围可调谐.实验上获得了低阈值自起振,重复频率为10.23 MHz,中心波长在1548.64～1600.24 nm内连续可调,边模抑制比大于44 dB的超短脉冲输出.     

单偏振控制器环形腔光纤激光器实验研究

理论分析了非线性偏振旋转环形腔作为类饱和可吸收体获得脉冲的物理机理。在光纤环形腔结构中,采用单个偏振控制器实现了非线性偏振旋转锁模,直接获得了脉冲宽度为131 fs的超短脉冲输出。实验中,采用性能稳定的976 nm半导体二极管激光器作为抽运源,使用高掺杂浓度的Er3 光纤为增益介质,通过调节偏振控制器,获得了光谱谱宽(3 dB带宽处)为23.5 nm的稳定锁模脉冲输出。脉冲中心波长为1535.9 nm,平均功率为5.91 mW,脉冲重复率为11.20 MHz。     

高重复频率全光纤被动锁模掺铒光纤激光器

报道了一种高重复频率全光纤非线性偏振旋转锁模掺铒光纤激光器, 获得了重复频率217 MHz的锁模脉冲输出. 该激光器使用一个偏振相关隔离器和一个偏振控制器即可获得稳定的锁模脉冲输出, 结构简单, 系统稳定. 激光器锁模脉冲的脉冲宽度为69 fs, 3 dB光谱宽度为56 nm, 射频频谱信噪比为76 dB.     

基于非线性偏振旋转效应的多波长掺铥锁模光纤激光器

运用非线性偏振旋转效应实现了一种掺铥锁模多波长光纤激光器.采用环形腔结构,以1 565nm半导体光源为泵浦源,3m长掺铥光纤为增益介质.利用非线性偏振旋转效应进行滤波.当泵浦功率在800mW时,通过调节光纤偏振控制器,激光器出现了被动锁模状态的脉冲输出,脉冲重复频率为3.178MHz,脉冲宽度为617ps.进一步增加泵浦功率,激光器进入多波长输出的工作状态.调节偏振控制器在室温下得到1~5个稳定的波长激光输出,边摸抑制比为40~60dB.     

超短脉冲掺Yb3+光纤激光器实验研究

报道了掺Yb3+光纤激光器产生超短脉冲的实验研究超短脉冲激光器抽运源采用波长为976 nm的半导体激光器,采用非线性偏振旋转相加脉冲锁模技术,通过调节偏振控制器的方向,实现了掺Yb3+光纤激光器的稳定锁模输出,获得了最大输出功率为7.02 mW,脉冲激光光谱宽度为6 nm,重复频率为13.7 MHz.     

宽可调谐自起振被动锁模掺铒光纤激光器

分析了利用非线性偏振旋转效应作为等效可饱和吸收体锁模的原理,并用该方法构建起环形腔被动锁模掺铒光纤激光器,结合可调谐滤波器腔外滤波的方法实现锁模脉冲波长的连续可调谐.实验中得到自起振、平均输出功率0.313 mW,脉冲半极大全宽度(FWHM)1.5 ps,中心波长1562.3nm,重复频率13.9MHz的稳定被动锁模脉冲序列输出,滤波后输出脉冲中心波长在1553.2～1571.4 nm内连续可调,得到谱宽2.5 nm以下,脉宽小于1.8 ps的限变脉冲输出.     

8字形腔波长可调谐锁模脉冲光纤激光器

采用非线性光纤环形镜加脉冲锁模技术及可调谐光纤光栅滤波器,对8字形腔被动锁模掺铒光纤激光器进行了波长可调谐输出的实验研究.在EDFA抽运光功率一定的情况下,通过调节偏振控制器和可调谐光纤光栅滤波器,获得了光谱稳定、重复频率1.1 MHz、输出功率起伏小于0.8 dBm、中心波长在1 548~1 570 nm内连续可调的短脉冲输出.该激光器可实现自启动锁模,且长时间稳定工作无需任何调整.     

正色散光纤激光器中矩形耗散孤子与高斯光谱脉冲的切换锁模

基于单壁碳纳米管与非线性偏振旋转技术在锁模光纤激光器中仿真和实验观测到矩形耗散孤子与高斯光谱脉冲的切换锁模.矩形耗散孤子的光谱与脉冲宽度分别为～6.33ps和～12.54nm,具有非常强的啁啾.适当地调节偏振控制器,可以获得具有高斯型光谱和脉冲的锁模状态,其光谱和脉冲宽度分别为～1.87ps和～2.2nm.高斯型光谱脉冲的时间带宽积为0.51,几乎没有啁啾.不同锁模状态间的切换归因于偏振控制器导致的腔内偏振的改变.     

非线性偏振旋转中偏振控制器方位角的研究

提出一种基于Jones矩阵的非线性偏振旋转锁模光纤激光器数值模型, 对偏振控制器波片方位角的描述具有物理意义清晰的优点. 数值仿真得到均方根宽度为0.28 ps的超短脉冲, 时域对称且振幅稳定. 搭建了非线性偏振旋转锁模光纤激光器, 系统可以自启动, 得到了重复频率为67.35 MHz的锁模脉冲输出. 数值仿真和实验结果都表明偏振控制器两个波片的方位角α₁和α₂都具有周期性, 周期分别为180°和90°. 由于随机双折射的影响, 实验测得的波片方位角调谐范围比数值仿真的结果小, 这一点通过在数值仿真模型中加入随机双折射的作用而得到证明.     

基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器

报道了一种基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器.该激光器采用环形腔结构,利用自制的三层石墨烯薄膜作为可饱和吸收体实现锁模.同时在腔内插入一个窄带光纤光栅,约束腔内起振的纵模数,适当调节抽运功率和偏振控制器的角度,得到了重复频率为3.8 MHz、脉宽在3.8—94.3 ns之间灵活可调的2μm纳秒锁模脉冲输出,整个脉宽调节范围超过90 ns.此外,由于获得的兆赫兹纳秒锁模脉冲时间带宽积在49—1119范围内,即存在强烈的啁啾,因而可作为2μm波段啁啾脉冲放大系统中的种子源使用.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.