First principles study of gallium‐cleaning for hydrogen‐contaminated α‐Al2O3(0001) surfaces

The use of gallium for cleaning hydrogen‐contaminated Al₂O₃ surfaces is explored by performing first principles density functional calculations of gallium adsorption on a hydrogen‐contaminated Al‐terminated α‐Al₂O₃(0001) surface. Both physisorbed and chemisorbed H‐contaminated α‐Al₂O₃(0001) surfaces with one monolayer (ML) gallium coverage are investigated. The thermodynamics of gallium cleaning are considered for a variety of different asymptotic products, and are found to be favorable in all cases. Physisorbed H atoms have very weak interactions with the Al₂O₃ surface and can be removed easily by the Ga ML. Chemisorbed H atoms form stronger interactions with the surface Al atoms. Bonding energy analysis and departure simulations indicate, however, that chemisorbed H atoms can be effectively removed by the Ga ML. © 2013 Wiley Periodicals, Inc.     

Effect of SiC/nano‐CeO2 on wear resistance and microstructures of Ti3Al/γ‐Ni matrix laser‐cladded composite coating on Ti–6Al–4V alloy

The Ti–6Al–4V alloy is an important aviation material, but has a poor resistance to slide wear. Laser cladding of the Al₃Ti + Ni/Cr/C + TiB₂/Al₂O₃ + SiC/nano‐CeO₂ preplaced powders on the Ti–6Al–4V alloy can form the Ti₃Al/γ‐Ni matrix composite coating, which improves the wear resistance of the substrate. In this study, the Al₃Ti + Ni/Cr/C + TiB₂/Al₂O₃ + SiC/nano‐CeO₂ laser‐cladded coating was researched by means of X‐ray diffraction, scanning electron microscopy, and energy dispersive spectrometry. The experimental results indicate that under the action of SiC/nano‐CeO₂, this composite coating exhibited a fine microstructure. Furthermore, the proper content of nano‐CeO₂ decreased the crack tendency. The results above indicated that, it is feasible to improve the tribological property of the Al₃Ti + Ni/Cr/C + TiB₂/Al₂O₃ laser‐cladded coating by adding of SiC/nano‐CeO₂. Copyright © 2011 John Wiley & Sons, Ltd.     

High‐temperature oxidation behavior of Ni‐based superalloys with Nb and Y and the interface characteristics of oxidation scales

Ni‐based superalloys with niobium (Nb) or/and yttrium (Y) were prepared by vacuum melting. The oxidation kinetics of these alloys was studied by thermogravimetry at 800 °C for 100 h in static air. Morphology of oxides was studied using SEM, and the composition was analyzed by X‐ray diffraction. Energy‐dispersive X‐ray spectrometer was employed to examine the linear element distribution of the cross section of the oxidation films. Results showed that the oxidation kinetics all followed a parabolic law at different stages. The oxide films were mainly comprised of Cr₂O₃, NiCr₂O₄, Al₂O₃ and TiO₂. All the oxide films exhibited layered structure owing to different oxidation stages. With the addition of Nb or Y, the high‐temperature oxidation resistance of the superalloy was improved significantly and the surface morphology of the oxidation film was ameliorated. The comprehensive effect of Nb and Y was remarkable in improving the high‐temperature oxidation resistance of Ni‐based alloys. Copyright © 2014 John Wiley & Sons, Ltd.     

Green one‐pot preparation of α‐Fe2O3@carboxyl‐functionalized yeast composite with high adsorption and catalysis properties for removal of methylene blue

Herein, the α‐Fe₂O₃@carboxyl‐functionalized yeast composite (α‐F@CFYC) was synthesized by direct oxidation of yeast with K₂FeO₄ and used as a novel adsorbent/heterogeneous Fenton catalyst for removal of methylene blue (MB). The obtained α‐F@CFYC was fully characterized by scanning electron microscopy, EDX, X‐ray diffraction analysis, Fourier‐transform infrared, thermogravimetry, and X‐ray photoelectron spectroscopy, respectively, and the corresponding results showed that α‐Fe₂O₃ nanoparticles were successfully obtained and deposited on yeast surface, as well as more functional groups were introduced/exposed on yeast surface. Furthermore, various influence parameters (eg, contact time, initial pH, and MB concentration) on the adsorption/catalysis ability of α‐F@CFYC for MB have been investigated in detail under ambient conditions. As a result, owing to the synergetic effect of the loaded α‐Fe₂O₃ and the introduced/exposed functional groups on yeast surface, the as‐obtained α‐F@CFYC exhibited high adsorption capacities and good catalysis degradation properties for MB.     

Microstructural characterization of oxide layers formed on Ni–20Cr–8Al alloy foam using transmission electron microscopy

Microstructural characterization was carried out during the pre‐oxidation of Ni–20Cr–8Al alloy foam using transmission electron microscopy (TEM). During the pre‐oxidation at 1000 °C for 1, 30, and 60 min in air, the sequential formations of NiO, NiCr₂O₄, Cr₂O₃, and α‐Al₂O₃ 1‐μm‐thick oxide layers were, respectively, characterized. Initially, during pre‐oxidization, the layers formed abnormally in an island growth mode, but they grew to be morphologically uniform after 30 min. Pores were found after only 1 min in the middle region of the oxide layers, near the Cr₂O₃ layer, and then these developed into critical micro‐cracks after 60 min. Copyright © 2017 John Wiley & Sons, Ltd.     

Effect of Calcination Temperature and Pretreatment with Reaction Gas on Properties of Co/γ‐Al2O3 Catalysts for Partial Oxidation of Methane

The effects of calcination temperature and feedstock pretreatment on the catalytic performance of Co/γ‐Al₂O₃ catalysts were studied for partial oxidation of methane (POM) to synthesis gas, with emphasis on the role of feedstock pretreatment. The physicochemical properties of the catalysts were characterized by N₂ adsorption, X‐ray diffraction (XRD), transmission electron microscopy (TEM), H₂ temperature‐programmed reduction (H₂‐TPR), and Raman spectroscopy. The results showed that the pretreatment of the catalyst by reaction gas significantly improved the catalytic activity and stability for the POM reaction. On the other hand, the effect of calcination temperature was less significant. Although the initial activity was increased by an increased calcination temperature, the catalyst without the feedstock pretreatment suffered a rapid deactivation. The reaction‐atmosphere pretreatment was revealed as a process that mainly modified the surface structure of the catalyst. In that process, the formation of a CoAl₂O₄‐like compound led to high Co metal dispersion after reduction, and the transformation of the carrier into α‐Al₂O₃ occurred over the catalyst surface. Both the high dispersion of cobalt and the presence of α‐Al₂O₃ surface phase were assumed as the important factors resulting in an excellent catalytic performance in terms of high activity and high stability.     

Fe K‐Edge X‐ray Absorption Fine Structure Determination of γ‐Al2O3‐Supported Iron‐Oxide Species

The structure of FeO_x species supported on γ‐Al₂O₃ was investigated by using Fe K‐edge X‐ray absorption fine structure (XAFS) and X‐ray diffraction (XRD) measurements. The samples were prepared through the impregnation of iron nitrate on Al₂O₃ and co‐gelation of aluminum and iron sulfates. The dependence of the XRD patterns on Fe loading revealed the formation of α‐Fe₂O₃ particles at an Fe loading of above 10 wt %, whereas the formation of iron‐oxide crystals was not observed at Fe loadings of less than 9.0 wt %. The Fe K‐edge XAFS was characterized by a clear pre‐edge peak, which indicated that the Fe?O coordination structure deviates from central symmetry and that the degree of Fe?O?Fe bond formation is significantly lower than that in bulk samples at low Fe loading (<9.0 wt %). Fe K‐edge extended XAFS oscillations of the samples with low Fe loadings were explained by assuming an isolated iron‐oxide monomer on the γ‐Al₂O₃ surface.     

High‐temperature mass spectrometric study of the vaporization processes in the system CaO‐MgO‐Al2O3‐Cr2O3‐FeO‐SiO2

Knudsen effusion mass spectrometry was used to study vaporization processes and thermodynamic properties of twenty samples of chromium‐containing slags in the CaO‐MgO‐Al₂O₃‐Cr₂O₃‐FeO‐SiO₂ system in the temperature range 1850–2750 K. Tungsten cells were used and Cr₂O₃ solid was used as a reference material. The system was calibrated using liquid gold. As FeO was the first emanating vapor species, monitoring of the chromium‐containing species could be carried out only after the complete vaporization of FeO. This, however, was found to have very little impact on the concentration of the slags investigated. During the measurements, the ion current intensities of CrO⁺ and CrO species in the mass spectra of the vapor over the CaO‐MgO‐Al₂O₃‐Cr₂O₃‐FeO‐SiO₂ samples were monitored and compared with those corresponding to solid Cr₂O₃. Data on the partial pressures of vapor species as well as the activities of Cr₂O₃ as a function of temperature were obtained. The results are expected to be valuable in the optimization of slag composition in high alloy steelmaking processes. Copyright © 2009 John Wiley & Sons, Ltd.     

Mixed‐Metal MIL‐100(Sc,M) (M=Al,Cr, Fe) for Lewis Acid Catalysis and Tandem CC Bond Formation and Alcohol Oxidation

The trivalent metal cations Al³⁺, Cr³⁺, and Fe³⁺ were each introduced, together with Sc³⁺, into MIL‐100(Sc,M) solid solutions (M=Al, Cr, Fe) by direct synthesis. The substitution has been confirmed by powder X‐ray diffraction (PXRD) and solid‐state NMR, UV/Vis, and X‐ray absorption (XAS) spectroscopy. Mixed Sc/Fe MIL‐100 samples were prepared in which part of the Fe is present as α‐Fe₂O₃ nanoparticles within the mesoporous cages of the MOF, as shown by XAS, TGA, and PXRD. The catalytic activity of the mixed‐metal catalysts in Lewis acid catalysed Friedel–Crafts additions increases with the amount of Sc present, with the attenuating effect of the second metal decreasing in the order Al>Fe>Cr. Mixed‐metal Sc,Fe materials give acceptable activity: 40 % Fe incorporation only results in a 20 % decrease in activity over the same reaction time and pure product can still be obtained and filtered off after extended reaction times. Supported α‐Fe₂O₃ nanoparticles were also active Lewis acid species, although less active than Sc³⁺ in trimer sites. The incorporation of Fe³⁺ into MIL‐100(Sc) imparts activity for oxidation catalysis and tandem catalytic processes (Lewis acid+oxidation) that make use of both catalytically active framework Sc³⁺ and Fe³⁺. A procedure for using these mixed‐metal heterogeneous catalysts has been developed for making ketones from (hetero)aromatics and a hemiacetal.     

Conformational analysis of the disaccharide methyl α‐d‐mannopyranosyl‐(1→3)‐2‐O‐acetyl‐β‐d‐mannopyranoside monohydrate

The crystal structure of methyl α‐d ‐mannopyranosyl‐(1→3)‐2‐O‐acetyl‐β‐d ‐mannopyranoside monohydrate, C₁₅H₂₆O₁₂·H₂O, ( II ), has been determined and the structural parameters for its constituent α‐d ‐mannopyranosyl residue compared with those for methyl α‐d ‐mannopyranoside. Mono‐O‐acetylation appears to promote the crystallization of ( II ), inferred from the difficulty in crystallizing methyl α‐d ‐mannopyranosyl‐(1→3)‐β‐d ‐mannopyranoside despite repeated attempts. The conformational properties of the O‐acetyl side chain in ( II ) are similar to those observed in recent studies of peracetylated mannose‐containing oligosaccharides, having a preferred geometry in which the C2—H2 bond eclipses the C=O bond of the acetyl group. The C2—O2 bond in ( II ) elongates by ～0.02 Å upon O‐acetylation. The phi (?) and psi (ψ) torsion angles that dictate the conformation of the internal O‐glycosidic linkage in ( II ) are similar to those determined recently in aqueous solution by NMR spectroscopy for unacetylated ( II ) using the statistical program MA′AT, with a greater disparity found for ψ (Δ = ～16°) than for ? (Δ = ～6°).     

Plane‐wave density functional theory investigation of adsorption of 2,4,6‐trinitrotoluene on al‐hydroxylated (0001) surface of (4 × 4) α‐alumina

This article reports the results of the theoretical investigation of adsorption of 2,4,6‐trinitrotoluene (TNT) on Al‐hydroxylated (0001) surface of (4 × 4) α‐alumina (α‐Al₂O₃) using plane‐wave Density Functional Theory. Sixteen water molecules were used to hydroxylate the alumina surface. The Perdew–Burke–Ernzerhof functional and the recently developed van der Waals functional (vdW‐DF2) were used. The interaction of electron with core was accounted using the Vanderbilt ultrasoft pseudopotentials. It was found that hydroxylation has significant influence on the geometry of alumina and such changes are prominent up to few layers from the surface. Particularly, due to the Al‐hydroxylation the oxygen layers are decomposed into sublayers and such partitioning becomes progressively weaker for interior layers. Moreover, the nature of TNT adsorption interaction is changed from covalent type on the pristine alumina surface to hydrogen‐bonding interaction on the Al‐hydroxylated alumina surface. TNT in parallel orientation forms several hydrogen bonds compared to that in the perpendicular orientation with hydroxyl groups of the Al‐hydroxylated alumina surface. Therefore, the parallel orientation will be present in the adsorption of TNT on Al‐hydroxylated (0001) surface of α‐alumina. Further, the vdW‐DF2 van der Waals functional was found to be most suitable and should be used for such surface adsorption investigation. © 2014 Wiley Periodicals, Inc.     

A novel spinel coating on cobalt‐based Superalloy GH605 via an in‐situ oxidation approach

Cr‐Mn‐O spinel coating was prepared on the surface of cobalt‐based superalloy GH605 via an in‐situ oxidation method in H₂O‐H₂ environment. The composition, morphology, and chemical value state of the oxide spinel coatings were investigated by SEM, EDS, XRD, Raman spectra, and XPS. It indicated that the morphology of coating varied with oxidation temperature, and granular surface appeared when oxidation temperature increased to 1100°C. The formed Cr‐Mn‐O spinel coating was composed of Cr₂O₃ and MnCr₂O₄, and the thickness increased significantly with oxidation temperature. In the coating, Cr element existed in the state of Cr³⁺ ions and Cr⁶⁺ ions, while Mn element only existed in the form of Mn²⁺ ions.     

Study on the mechanism of catalytic synthesis of dimethyldichlorosilane by AlCl3/MIL‐53(Al)@γ‐Al2O3

Dimethyldichlorosilane, one of the most consumed organosilicon monomers in the industry, can be prepared in a highly efficient and environmentally friendly synthesis method of disproportionating methylchlorosilanes. However, the internal mechanism of the reaction remains unclear. In this paper, the mechanism catalyzed by AlCl₃/MIL‐53(Al) and AlCl₃/MIL‐53(Al)@γ‐Al₂O₃ catalysts was calculated at B3LYP/6‐311++G(3df, 2pd) level by using the density functional theory (DFT). The results showed that although the two catalysts had similar active structures, the catalytic effects were significantly different. The Lewis acid center on the surface of γ‐Al₂O₃ in the core‐shell catalyst is complementary to the classic Lewis acid AlCl₃ through the spatial superposition effect, which greatly improves the Lewis acid catalytic activity of AlCl₃/MIL‐53(Al)@γ‐Al₂O₃.     

Theoretical Study on Reactivity of Electron Transfer in Model—System of Oxidation of α—Amino Carbon—centered Radical by O2

Electron transfer reaction between a simplified model model molecule of α－amino carbon-centered radical and O2 has studied with ab initio calculations at the MP2/6-31 G^**//UHF/6-31 G^** level,The reactant complex and the ion pair complex have been optimized and employed to perform calculation of the reaction heat and the reorganization energy,Solvent effects have been considered by applyning the conductor-like screening model,Theoretical results show that the highly endothermic charge separation process ,in which one electron transfers from the α－amino carbon-centered radical to O2,so as to form an ion pair complex,is difficult to occur in gas-phase,By apply-ing an external electronic field to prepare the charge-locallized molecular orbitals,the charge-separated state has been obtained using the initial-guess-induced self-consistent field technique,The theoretical investigations indicate that the solvent effect in the process of the oxidation of α-animo carbon-centered radical by O2 is remarkable.From the rate constant estima-tion ,it can be predicted that the oxidation of the model donor molecule by O2 can proceed,but not very fast.A peroxyl radi-cal compound has been found to be a competitive intermediate in the oxidation process.     

Cr concentration driving the structural,mechanical, and thermodynamic properties of Cr-Al compounds from first-principles calculations

Cr-Al binary compounds are regarded as the potential high-temperature structural materials. However, the structure and important properties of Cr-Al compounds are not completely unclear. Here, we report on the influence of Cr concentration on the structural, mechanical, and thermodynamic properties of Cr-Al compounds by using the first-principles calculations. Four novel Cr-Al compounds, Cr₃Al₈ with monoclinic structure (C2/m), Cr₃Al₅ with hexagonal structure (P63mc), Cr₂Al₃ with tetragonal structure (I4/mmm), and Cr₃Al with cubic structure (Pm-3 m), are predicted. The calculated elastic modulus of Cr-Al compounds gradually increases with increasing Cr concentration. Compared to other Cr-Al compounds, our predicted Cr₃Al with cubic structure exhibits a strong deformation resistance and high hardness due to symmetrical Cr Al bonds. However, the Debye temperature of Cr₇Al₃ is larger than that of other Cr-Al compounds. The calculated phonon density of state shows that the high-temperature thermodynamic properties of Cr-Al compounds are attributed to the vibration of Al atom and Cr Al bond.     

Vapor‐Phase Aldolization of n‐Butyraldehyde to 2‐Ethyl‐2‐Hexenal over Solid‐Base Catalysts

Vapor‐phase aldol condensation of n‐butyraldehyde to 2‐ethyl‐2‐hexenal was studied at 1 atm and 150～ 300°C in a fixed‐bed, integral‐flow reactor by using NaX, KX, γ‐Al₂O₃ and Na/NaOH/γ‐Al₂CO₃ catalysts. Ion exchange of NaX zeolite with potassium acetate solution results in a decrease of crystallinity and apparent lowering of surface area, whereas the basic strength is enhanced. Treatment of γ‐Al₂O₃ with NaOH and Na causes a large decrease of the surface area but strong enhancement of the catalyst basicity. The catalytic activity on the basis of unit surface area is in the order Na/NaOH/γ‐Al₂O₃ < KXU < KXW < NaX >γ‐Al₂O₃, in accordance with the relative catalyst basic strength. The molar ratio of trimeric to dimeric products increases with increasing the reaction temperature and the catalyst basic strength except for Na/NaOH/γ‐Al₂O₃. Very high selectivity of 2‐ethyl‐2‐hexenal (>98.5%) was observed for reactions over NaX zeolite at 150°C. Based on the FT‐IR and the catalytic results, the reaction paths are proposed as follows: self‐aldol condensation of n‐butyraldehyde, followed by dehydration produces 2‐ethyl‐2‐hexenal, which then reacts with n‐butyraldehyde and successively dehydrates to 2,4‐diethyl‐2,4‐octadienal and 1,3,5‐triethylbenzene. For the reaction over NaX, the calculated Arrhenius frequency factor and activation energy are 314 mol/g·h and 32.6 kJ/mol, respectively.     

A DFT quantum‐chemical study on the structures and active sites of polymethylaluminoxane

The electronic structure and geometry of polymethylaluminoxane (MAO) [—Al(CH₃)O—]_n with different size (n = 4–12) have been studied using quantum‐chemical DFT (density functional theory) calculations. It has been found: 1) Starting from n = 6, the three‐dimensional oxo‐bridged (cage) structure of MAO is more stable than the cyclic structure. 2) Both for cage structure and for cyclic structure the Lewis acidity of Al atoms characterized by their net positive charge amplifies with increasing size of MAO (n). 3) Trimethylaluminium (AlMe₃) reacts with the cage structure of MAO with cleavage of an Al‐O dative bond and formation of acidic tri‐coordinated Al^v and basic di‐coordinated O^v atoms in the MAO molecule. Two molecules AlMe₃ are associated with acidic Al^v and basic O^v centers. As the MAO increases in size, the acidity of Al^v centers amplifies and the distance Al^v‐(AlMe₃) shortens; on the contrary, interaction of AlMe₃ with O^v centers weakens and the distance O^v‐(AlMe₃) increases with increasing n value. The total heat of Al₂Me₆ interaction with MAO (sum interaction of Al^v‐(AlMe₃) and O^v‐(AlMe₃)) noticeably decreases as the size of MAO increases (from 50.9 kcal/mol for n = 4 to 20.2 kcal/mol for n = 12). It is proposed that acidic Al^v and basic O^v centers formed in the cage structure of MAO interact with zirconocene yielding ‘cation‐like’ zirconium active centers.     

Effect of inorganic oxide supports on the activity of chromium‐based catalysts in ethylene trimerization

Novel heterogeneous catalysts were prepared using immobilization of bis(2‐decylsulfanylethyl)amine–CrCl₃ (Cr‐SNS‐D) on various supports, namely commercial TiO₂, Al₂O₃ and magnetic Fe₃O₄@SiO₂ nanoparticles, to yield solid catalysts denoted as support@Cr‐SNS‐D. The structure of the catalysts was confirmed on the basis of spectroscopic analyses, N₂ adsorption–desorption and inductively coupled plasma (ICP) analysis. The surface areas of Al₂O₃@Cr‐SNS‐D, Fe₃O₄@SiO₂@Cr‐SNS‐D and TiO₂@Cr‐SNS‐D catalysts were determined to be 70, 23 and 41 m² g^?1, respectively. A decrease in surface area from that of the supports clearly establishes accurate immobilization of Cr‐SNS‐D catalyst on the surface of the parent carriers. The loading of Cr was determined to be 0.02, 0.16 and 0.11 mmol g^?1 for Cr‐SNS‐D supported on TiO₂, Al₂O₃ and Fe₃O₄@SiO₂, respectively, using ICP analysis. After preparation and full characterization of the catalysts, ethylene trimerization reaction was accomplished in 40 ml of dry toluene, at 80°C and 25 bar ethylene pressure and in the presence of methylaluminoxane (Al/Cr = 700) within 30 min. The supported chromium catalysts were found to be efficient and selective for the ethylene trimerization reaction. The highest activity (74 650 g_1‐hexene g_Cr^?1 h^?1), as well as no polyethylene formation during reaction processes, was observed when TiO₂ was used as the catalyst support.     

Efficient conversion of fructose to 5‐hydroxymethylfurfural by functionalized γ‐Al2O3 beads

Millimeter size γ‐Al₂O₃ beads were prepared by alginate assisted sol–gel method and grafting organic groups with propyl sulfonic acid and alkyl groups as functionalized γ‐Al₂O₃ bead catalysts for fructose dehydration to 5‐hydroxymethylfurfural (5‐HMF). Experiment results showed that the porous structure of γ‐Al₂O₃ beads was favorable to the loading and dispersion of active components, and had an obvious effect on the properties of the catalyst. The lower calcination temperature of γ‐Al₂O₃ beads increased the specific surface area, the hydrophobicity and the activity of catalysts. Competition between the reaction of alkyl groups and ‐SH groups with surface hydroxyl during the preparation process of the catalyst influenced greatly the acid site densities, hydrophobic properties and activity of the catalyst. With an increase in the alkyl group chain, the hydrophobicity of catalysts increased obviously and the activity of the catalyst was enhanced. The most hydrophobic catalyst C₁₆‐SO₃H‐γ‐Al₂O₃–650°C exhibited the highest yield of 5‐HMF (84%) under the following reaction conditions: reaction medium of dimethylsulfoxide/H₂O (V/V, 4:1), catalyst amount of 30 mg, temperature of 110°C and reaction time of 4 hr.     

Synthesis and Characterization of Spinel‐Type Gallia‐Alumina Solid Solutions

By precipitation with ammonia of ethanolic solutions containing the appropriate proportions of gallium and aluminium nitrate, following by calcination of the resulting gels at 773 K, mixed Ga₂O₃/Al₂O₃ oxides having Ga:Al ratios of 9:1, 4:1, 1:1, 1:4 and 1:9 were obtained. Powder X‐ray diffraction showed that these mixed metal oxides form a series of solid solutions having the spinel‐type structure; also shown by γ‐Al₂O₃ and γ‐Ga₂O₃. The specific surface area (determined by nitrogen adsorption at 77 K) was found to range from 160 m² g^?1 for the mixed oxide having Ga:Al = 9:1 up to 370 m² g^?1 for that having Ga:Al = 1:9. High resolution MAS NMR showed that Ga³⁺ and Al³⁺ ions occur at both tetrahedral and octahedral sites in the spinel‐type structure of the mixed metal oxides, although there is a preferential occupation of tetrahedral sites by Ga³⁺ ions. A proportion of penta‐coordinated Al³⁺ ions was also found. IR spectra of carbon monoxide adsorbed at 77 K showed that the mixed metal oxides have a considerable Lewis acidity, related mainly to tetrahedrally coordinated metal ions exposed at crystal surfaces. The characteristic infrared absorption band of coordinated (adsorbed) CO appears in the range 2205–2190 cm^?1, and its peak wavenumber is nearly independent of Ga:Al ratio in the mixed gallia‐alumina oxides.