Anilinic N‐Oxides Support Cytochrome P450‐Mediated N‐Dealkylation through Hydrogen‐Atom Transfer

The mechanism of N‐dealkylation mediated by cytochrome P450 (P450) has long been studied and argued as either a single electron transfer (SET) or a hydrogen atom transfer (HAT) from the amine to the oxidant of the P450, the reputed iron–oxene. In our study, tertiary anilinic N‐oxides were used as oxygen surrogates to directly generate a P450‐mediated oxidant that is capable of N‐dealkylating the dimethylaniline derived from oxygen donation. These surrogates were employed to probe the generated reactive oxygen species and the subsequent mechanism of N‐dealkylation to distinguish between the HAT and SET mechanisms. In addition to the expected N‐demethylation of the product aniline, 2,3,4,5,6‐pentafluoro‐N,N‐dimethylaniline N‐oxide (PFDMAO) was found to be capable of N‐dealkylating both N,N‐dimethylaniline (DMA) and N‐cyclopropyl‐N‐methylaniline (CPMA). Rate comparisons of the N‐demethylation of DMA supported by PFDMAO show a 27‐fold faster rate than when supported by N,N‐dimethylaniline N‐oxide (DMAO). Whereas intermolecular kinetic isotope effects were masked, intramolecular measurements showed values reflective of those seen previously in DMAO‐ and the native NADPH/O₂‐supported systems (2.33 and 2.8 for the N‐demethylation of PFDMA and DMA from the PFDMAO system, respectively). PFDMAO‐supported N‐dealkylation of CPMA led to the ring‐intact product N‐cyclopropylaniline (CPA), similar to that seen with the native system. The formation of CPA argues against a SET mechanism in favor of a P450‐like HAT mechanism. We suggest that the similarity of KIEs, in addition to the formation of the ring‐intact CPA, argues for a similar mechanism of Compound I (Cpd I) formation followed by HAT for N‐dealkylation by the native and N‐oxide‐supported systems and demonstrate the ability of the N‐oxide‐generated oxidant to act as an accurate mimic of the native P450 oxidant.     

Functionalized boron carbide for enhancement of anticorrosion performance of epoxy resin

In this study, epoxy coatings were modified by adding various compositions of B₄C particles. In order to achieve proper dispersion of particles in the epoxy coating and increasing chemical interactions between particles and polymeric coating, the surface of the B₄C particles was treated with γ‐(2,3‐epoxypropoxy) propytrimethoxysilane (KH560). The surface modification and microstructure of B₄C were characterized by Fourier transform infrared, X‐ray diffraction, X‐ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. Electrochemical impedance spectroscopy was also used to evaluate the impedance of coatings. The results revealed that the KH560 not only enhanced the interaction between B₄C particles and epoxy resin but also exhibited a remarkable ability to improve the anticorrosion performance of epoxy resin. The epoxy coating with the 3 wt% B₄C‐KH560 particles exhibited the best anticorrosion performance, which can be attributed to the best uniform dispersion of the B₄C‐KH560 particles, and the particles effectively block the aggressive species (Cl⁻, O₂, and H₂O) from the coating.     

Effect of AA2024‐T3 surface pretreatment on the physicochemical properties and the anticorrosion performance of poly(γ‐glycidoxypropyltrimethoxysilane) sol‐gel coating

This study investigated the dependence of the anticorrosion performance of a poly(γ‐glycidoxypropyltrimethoxysilane) (poly(γ‐GPTMS)) sol‐gel coating on AA2024‐T3 aluminum alloy surface state. Two different AA2024‐T3 surface pretreatment procedures were tested: a degreasing with acetone and a chemical multistep etching process (industrial chemical etching pretreatment). Poly(γ‐GPTMS) coatings were deposited onto both pretreated surfaces using the dip‐coating technique. Surfaces were characterized principally by scanning electron microscopy, X‐ray photoelectron spectroscopy, Fourier transform infrared attenuated total reflectance, contact angles, and roughness measurements. Moreover, for the coated AA2024‐T3 surfaces, a pull‐off test was used to evaluate the poly(γ‐GPTMS) adhesion to the pretreated surface. Bare surface properties depended on the applied pretreatment. The chemically etched surface was the roughest and the most concentrated in hydroxyl groups. In addition, comparatively to the degreased surface, it has a more hydrophobic character. Poly(γ‐GPTMS) coating revealed an uneven nature and a poor adhesion once it was deposited onto the degreased surface. Coatings anticorrosion performances were evaluated using electrochemical impedance spectroscopy measurements (EIS). Electrochemical impedance spectroscopy data proved that the sol‐gel coating applied onto the chemically etched surface had better anticorrosion performance.     

Fe3O4‐supported Schiff‐base copper (II) complex: A valuable heterogeneous nanocatalyst for one‐pot synthesis of new pyrano[2,3‐b]pyridine‐3‐carboxamide derivatives

A novel Cu (II) Schiff‐base complex immobilized on core‐shell magnetic Fe₃O₄ nanoparticles (Fe₃O₄@SPNC) was successfully designed and synthesized. The structural features of these nanoparticles were studied and confirmed by using various techniques including FT‐IR spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy‐dispersive X‐ray spectroscopy (EDS), vibrating sample magnetometer (VSM), X‐Ray diffraction (XRD), wavelength dispersive X‐ray spectroscopy (WDX), and inductively coupled plasma (ICP). These newly synthesized nanoparticles have been used as efficient heterogeneous catalytic system for one‐pot multicomponent synthesis of new pyrano[2,3‐b]pyridine‐3‐carboxamide derivatives. Notably, the catalyst could be easily separated from the reaction mixture by using an external magnet and reused for several successive reaction runs with no significant loss of activity or copper leaching. The present protocol benefits from a hitherto unreported MNPs‐immobilized Cu (II) Schiff‐base complex as an efficient nanocatalyst for the synthesis of newly reported derivatives of pyrano[2,3‐b]pyridine‐3‐carboxamide from one‐pot multicomponent reactions.     

Synergistic effect of functional carbon nanotubes and graphene oxide on the anti‐corrosion performance of epoxy coating

In this work, we reported the synergistic effect of functional carbon nanotubes (CNTs) and graphene oxide (GO) on the anticorrosion performance of epoxy coating. For this purpose, the GO and CNTs were firstly modified by the 3‐aminophenoxyphthalonitrile to realize the nitrile functionalized graphene oxides (GO‐CN) and carbon nanotubes (CNTs‐CN). As modified GO‐CN and CNTs‐CN were characterized and confirmed by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and gravimetric analyzer. It was found that about 19 and 24 wt% of 3‐aminophenoxyphthalonitrile were grafted onto the surface of the GO and CNTs, respectively. The electrochemical impedance spectroscopy results showed that the GO‐CN&CNTs‐CN hybrid materials exhibit a remarkable superiority in enhancing the anticorrosion performance of epoxy coatings. Significant synergistic effect of the lamellar structural GO‐CN and CNTs‐CN on the anticorrosion performance of epoxy composite coatings was designed. Besides, the epoxy coating with 1 wt% of the GO‐CN&CNTs‐CN hybrid exhibited the best anticorrosion performance, in which the impedance showed the largest one (immersion in 3.5 wt% of NaCl solution for 168 hr). Copyright © 2016 John Wiley & Sons, Ltd.     

Corrosion protection performance of ceria‐copolymer bilayer coating on low nickel stainless steel in 0.5 M H2SO4 medium

In this paper, we have reported the anti‐corrosion performance of ceria / poly (indole‐co‐pyrrole) (Ce/(poly(In‐co‐Py)) bilayer coating on low nickel stainless steel (LN SS). Electrochemical polymerization of (poly (In‐co‐Py)) was achieved on ceria‐coated LN SS (CeO₂/LN SS) in acetonitrile medium containing LiClO₄ (ACN‐LiClO₄) by cyclic voltammetric technique. The coatings were characterized by analytical techniques like Fourier transform infrared spectroscopy, scanning electron microscopy with energy dispersive analysis of X‐ray, respectively. The mechanical behavior of the coatings was studied using peel test, hardness and wear resistance tests. The corrosion defensive performance of this bilayer coating on LN SS was investigated using electrochemical techniques such as potentiodynamic polarization and electrochemical impedance spectroscopy in 0.5 M H₂SO₄. These results show that the bilayer coating on LN SS lowered the permeability of corrosive ions present in the acidic medium and thus acts as a barrier against the attack of corrosive environment. Copyright © 2012 John Wiley & Sons, Ltd.     

Synthesis and NMR characterization of 6‐Phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose

Cellulose ( 1 ) was converted for the first time to 6‐phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 6 ) in 33% overall yield. Intermediates in the five‐step conversion of 1 to­ 6 were: 6‐O‐tritylcellulose ( 2 ), 6‐O‐trityl‐2,3‐di‐O‐methylcellulose ( 3 ), 2,3‐di‐O‐methylcellulose ( 4 ); and 6‐bromo‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 5 ). Elemental and quantitative carbon‐13 analyses were concurrently used to verify and confirm the degrees of substitution in each new polymer. Gel permeation chromotography (GPC) data were generated to monitor the changes in molecular weight (DP_w) as the synthesis progressed, and the compound average decrease in cellulose DP_w was ～ 27%. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to characterize the decomposition of all polymers. The degradation temperatures ( °C) and percent char at 500 °C of cellulose derivatives 2 to 6 were 308.6 and 6.3%, 227.6 °C and 9.7%, 273.9 °C and 30.2%, 200.4 °C and 25.6%, and 207.2 °C and 27.0%, respectively. The glass transition temperature (T_g) of­6‐O‐tritylcellulose by dynamic mechanical analysis (DMA) occurred at 126.7 °C and the modulus (E′, Pa) dropped 8.9 fold in the transition from ?150 °C to + 180 °C (6.6 × 10⁹ to 7.4 × 10⁸ Pa). Modulus at 20 °C was 3.26 × 10⁹ Pa. Complete proton and carbon‐13 chemical shift assignments of the repeating unit of the title polymer were made by a combination of the HMQC and COSY NMR methods. Ultimate non‐destructive proof of carbon–carbon bond formation at C6 of the anhydroglucose moiety was established by generating correlations between resonances of CH₂6 (anhydroglucose) and C1′, H2′, and H6′ of the attached aryl ring using the heteronuclear multiple‐bond correlation (HMBC) method. In this study, we achieved three major objectives: (a) new methodologies for the chemical modification of cellulose were developed; (b) new cellulose derivatives were designed, prepared and characterized; (c) unequivocal structural proof for carbon–carbon bond formation with cellulose was derived non‐destructively by use of one‐ and two‐dimensional NMR methods. Copyright © 2002 John Wiley & Sons, Ltd.     

Characterization and cytocompatibility of polydopamine on MAO‐HA coating supported on Mg‐Zn‐Ca alloy

Magnesium has been suggested as a potential biodegradable metal for the usage as orthopaedic implants. However, high degradation rate in physiological environment remains the biggest challenge, impeding wide clinical application of magnesium‐based biomaterials. In order to reduce its degradation rate and improve the biocompatibility, micro‐arc oxidation coating doped with HA particles (MAO‐HA) was applied as the inner coating, and polydopamine (PDA) film was synthesized by dopamine self‐polymerization as the outer coating. The microstructure evolution of the coating was characterized using scanning electron microscopy (SEM), atomic force microscope (AFM), X‐ray diffraction analyses (XRD), Fourier transform infrared spectroscopy (FT‐IR), and X‐ray photoelectron spectroscopy (XPS). The results showed that PDA film had covered the entire surface of MAO‐HA coating and the pore size of MAO‐HA coating decreased. The root mean square (RMS) roughness of PDA/MAO‐HA coatings was approximately 106.46 nm, which was closer to the optimum surface roughness for cellular attachment as compared with MAO‐HA coatings. Contact angle measurement indicated that the surface wettability had been transformed from hydrophobic to hydrophilic due to the introduction of PDA. The PDA/MAO‐HA coatings exhibited better corrosion resistance in vitro, with the self‐corrosion potential increasing by 150 mV and the corrosion current density decreasing from 2.09 × 10^?5 A/cm ² to 1.46 × 10^?6 A/cm ² . In hydrogen evolution tests, the corrosion rates of the samples coated with PDA/MAO‐HA and MAO‐HA were 4.40 and 5.95 mm/y, respectively. MTS assay test and cell‐surface interactions experiment demonstrated that PDA/MAO‐HA coatings exhibited good cellular compatibility and could promote the adhesion and proliferation of MC3T3‐E1 cells.     

Development of multifunctional polydimethylsiloxane (PDMS)‐epoxy‐zinc oxide nanocomposite coatings for marine applications

Multifunctional epoxy‐polydimethylsiloxane nanocomposite coatings with antifouling and anticorrosion characteristics have been developed via in situ polymerization method at different loading (1, 3, and 6.5 wt.%) of ZnO nanoparticles to cater marine applications. A detailed comparative analysis has been carried out between epoxy‐polydimethylsiloxane control (EPC) and ZnO‐reinforced coatings to determine the influence of ZnO loading on various properties. The incorporation of ZnO in EPC led to increase in root mean square (RMS) roughness to 126.75 nm and improved hydrophobicity showing maximum contact angle of 123.5° with low surface energy of 19.75 mN/m of nanocomposite coating as compared with control coating. The differential scanning calorimetry (DSC) result indicated improved glass transition temperature of nanocomposite coatings with highest T_g obtained at 83.69°C in case of 1 wt.% loading of ZnO. The increase in hydrophobicity of the system was accompanied by upgraded anticorrosion performance exhibiting 98.8% corrosion inhibition efficiency (CIE) as compared with control coating and lower corrosion rate of 0.12 × 10^?3 mm/year. The Taber abrasion resistance and pull‐off adhesion strength results indicated an increment of 34.7% and 150.7%, respectively, in case of nanocomposite coating as compared with the control coating. The hardness of nanocomposite coatings was also improved, and maximum hardness was found to be 65.75 MPa for nanocomposite coating with 1 wt.% of ZnO. Our study showed that the nanocomposite coating was efficient in inhibiting accumulation of marine bacteria and preventing biofouling for more than 8 months. The developed environment‐friendly and efficient nanocomposite material has a promising future as a high‐performance anticorrosive and antifouling coating for marine applications.     

Preparation by controlled radical polymerization and self‐assembly via base‐recognition of synthetic polymers bearing complementary nucleobases

The radical polymerization of three monomers bearing nucleobases 1‐(4‐vinylbenzyl)thymine (VBT), 1‐(4‐vinylbenzyl)uracil (VBU) and 9‐(4‐vinylbenzyl)adenine (VBA) was investigated. The corresponding homopolymers could be prepared in high yields via conventional radical polymerization. However, the resulting polymers were found to be only soluble in a few polar solvents. On the other hand, copolymers of dodecyl methacrylate (DMA) with either VBT or VBA could be prepared via both free radical polymerization and atom transfer radical polymerization and could be dissolved in a large variety of organic solvents. Moreover, the formed complementary copolymers P(VBT‐co‐DMA) and P(VBA‐co‐DMA) were found to self‐assemble in dilute solutions in dioxane or chloroform via base recognition, as evidenced by a significant hypochromicity effect in UV spectroscopy. Nevertheless, at higher concentrations in chloroform, both dynamic light scattering and optical microscopy indicate that P(VBT‐co‐DMA), P(VBA‐co‐DMA), or P(VBT‐co‐DMA)/P(VBA‐co‐DMA) mixtures spontaneously self‐assemble into micron size spherical aggregates. ¹H NMR and FTIR studies confirmed that the self‐assembly process is driven in all cases via H‐bond formation. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4805–4818, 2005     

Syntheses,Structures, and Photophysical Properties of Two Coordination Polymers Based on 2,3‐Dioxo‐1,2,3,4‐tetrahydroquinoxaline‐6‐carboxylic Acid

Two complexes based on the ligand 1,4‐dihydro‐2,3‐quinoxalinedione, namely [Mn(H₂L)₂(H₂O)₂]_n ( 1 ) and {[Zn₂(H₂L)₂(tz)₂] · 5H₂O}_n ( 2 ) (H₃L = 2,3‐dioxo‐1,2,3,4‐tetrahydroquinoxaline‐6‐carboxylic acid, Htz = 1,2,4‐triazole) were hydrothermally synthesized and characterized by elemental analyses, IR spectroscopy, as well as single‐crystal and powder X‐ray diffraction. Complex 1 exhibited a 1D comb‐like chain formed by H₂L^– anions linking Mn^II ions, whereas complex 2 was a 2D layer‐like structure with square‐shaped windows and outstretched arms built by combination of H₂L^– and tz^– ligands with Zn^II ions. The adjacent chains or layers connected with each other by intermolecular hydrogen bonding and π–π stacking to further extend to a 3D supermolecular framework. In addition, the thermal stabilities, luminescence properties, and optical energy gap of 1 and 2 were investigated in detail.     

Corrosion behavior of electroless Ni–P/TiO2 nanocomposite coatings

Composite Ni–P/nano‐TiO₂ coatings were prepared by simultaneous electroless deposition of Ni–P and nano‐TiO₂ on a low carbon steel substrate. The deposition was carried out from stirred solutions containing suspended nano‐TiO₂ particles. The Ni–P and Ni–P/nano‐TiO₂ coatings before and after heat treatment were characterized by X‐ray diffraction, scanning electron microscopy and energy dispersive X‐ray spectroscopy. The micro‐structural morphologies of the coatings significantly varied with the nano‐TiO₂ content. The corrosion resistance of as‐plated and heat‐treated Ni–P and Ni–P/nano‐TiO₂ coatings was investigated by anodic polarization, Tafel plots and electrochemical impedance spectroscopic (EIS) studies in 3.5% NaCl solution. Ni–P/nano‐TiO₂ coating exhibited superior corrosion resistance over Ni–P coating. Copyright © 2015 John Wiley & Sons, Ltd.     

Electrochemical Study of the Interactions of DNA with Redox‐Active Molecules Based on the Immobilization of dsDNA on the Sol‐Gel Derived Nano Porous Hydroxyapatite‐Polyvinyl Alcohol Hybrid Material Coating

A novel type of sol‐gel inorganic‐organic hybrid material coated on glassy carbon electrode used for immobilization of double‐stranded DNA (dsDNA) and study of dsDNA with redox‐active molecules was developed. The hybrid material coating was produced by sol‐gel method with nano hydroxyapatite (HAp)‐polyvinyl alcohol (PVA). The optimum composition of the hybrid material was first examined, and the morphology of the nano HAp‐PVA coatings was investigated with the help of Scanning Electron Microscope (SEM). DsDNA was immobilized in/on the nano HAp‐PVA hybrid coatings by adsorption and the characteristics of the dsDNA/HAp‐PVA/GCE were studied by cyclic voltammetry (CV) using the probes of Co(phen) and Fe(CN) . The results indicate that the dsDNA can be immobilized on the nano porous HAp‐PVA coating effectively and its stability can satisfy the necessity of study on the interactions of dsDNA with redox‐active molecules on the electrode surface. Co(bpy) and Co(phen) were used as the model molecule to study the interactions of dsDNA with redox‐active molecules. Information such as ratio (K_Ox/K_Red) of the binding constant for the oxidized and reduced forms of a bound species, interaction mode, including change in the mode of interaction, and “limiting” ratio K /K at zero ionic strength (μ) can be obtained using dsDNA/HAp‐PVA/GCE with about 2 μg of DNA samples.     

The formation mechanism and biocorrosion property of CaSiO3/CaHPO4 · 2H2O composite conversion coating on the extruded Mg‐Zn‐Ca alloy for bone implant application·

In this work, a calcium silicate and calcium phosphate (CaSiO₃/CaHPO₄ · 2H₂O) composite coating was applied by a chemical reaction to an extruded Mg‐Zn‐Ca magnesium alloy. SEM observation showed that a flat and sand‐like conversion coating was formed. X‐ray diffractometer (XRD) analysis indicated that the conversion coating was composed of CaHPO₄ · 2H₂O and a little amount of CaSiO₃. The formation mechanism of CaSiO₃/CaHPO₄ · 2H₂O composite conversion coatings was discussed. The electrochemical polarization tests showed that the conversion coating markedly improved the biocorrosion resistance of Mg‐Zn‐Ca alloy in Hank's solution. Copyright © 2010 John Wiley & Sons, Ltd.     

A Molecular Placeholder Strategy To Access a Family of Transition‐Metal‐Functionalized Vanadium Oxide Clusters

Systematic access to metal‐functionalized polyoxometalates has thus far been limited to lacunary tungsten oxide and molybdenum oxide clusters. The first controlled, stepwise bottom‐up assembly route to metal‐functionalized molecular vanadium oxides is now presented. A di‐vacant vanadate cluster with two metal binding sites, (DMA)₂[V₁₂O₃₂Cl]^3? (DMA=dimethylammonium) is formed spontaneously in solution and characterized by single‐crystal X‐ray diffraction, ESI mass spectrometry, ⁵¹V NMR spectroscopy, and elemental analyses. In the cluster, the metal binding sites are selectively blocked by hydrogen‐bonded DMA placeholder cations. Reaction of the cluster with transition metals TM (Fe³⁺, Co²⁺, Cu²⁺, Zn²⁺) gives access to mono‐functionalized vanadate clusters (DMA)[{TM(L)}V₁₂O₃₂Cl]^n? (L=ligand). Metal binding is accomplished by significant distortions of the vanadium oxide framework reminiscent of a pincer movement. Cluster stability under technologically relevant conditions in the solid‐state and solution is demonstrated.     

Synthesis,Characterization and Photoluminescence of Lanthanide Metal‐organic Frameworks,Constructed from Triangular 4,4′,4″‐s‐triazine‐1,3,5‐triyl‐p‐aminobenzoate Ligands

Eight isomorphous metal‐organic frameworks: [Ln₂(TATAB)₂(H₂O)(DMA)₆]·5H₂O (Ln = Sm ( 1 ), Eu ( 2 ), Gd ( 3 ), Tb ( 4 ), Dy ( 5 ), Er ( 6 ), Tm ( 7 ), Yb ( 8 )); TATAB = 4,4′,4″‐s‐triazine‐1,3,5‐triyl‐p‐aminobenzoate, DMA = N,N‐dimethylacetamide), were synthesized by the self‐assembly of lanthanide ions, TATAB, DMA and H₂O. Single‐crystal X‐ray crystallography reveals they are three dimensional frameworks with 2‐fold interpenetration. Solid‐state photoluminescence studies indicate ligand‐to‐metal energy transfer is more efficient for compounds 2 and 4 which exhibit intense characteristic lanthanide emissions at room temperature.     

CoFe2O4@SiO2‐CPTES‐Guanidine‐Cu(II): A novel and reusable nanocatalyst for the synthesis of 2,3‐dihydroquinazolin‐4(1H)‐ones and polyhydroquinolines and oxidation of sulfides

CoFe₂O₄@SiO₂‐CPTES‐Guanidine‐Cu(II) magnetic nanoparticles were synthesized and used as a new, inexpensive and efficient heterogeneous catalyst for the synthesis of polyhydroquinolines and 2,3‐dihydroquinazoline‐4(1H)‐ones and for the oxidation of sulfides. The structure of this nanocatalyst was characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, vibrating sample magnetometry, thermogravimetric analysis, X‐ray diffraction and inductively coupled plasma optical emission spectrometry. Simple preparation, high catalytic activity, simple operation, high yields, use of green solvents, easy magnetic separation and reusability of the catalyst are some of the advantages of this protocol.     

Fundamental Difference in Reductive Lithiations with Preformed Radical Anions versus Catalytic Aromatic Electron‐Transfer Agents: N,N‐Dimethylaniline as an Advantageous Catalyst

The reductive lithiation of phenyl thioethers, or alkyl chlorides, by either preformed aromatic radical anions or by lithium metal and an aromatic electron‐transfer catalyst, is commonly used to prepare organolithiums. Revealed herein is that these two methods are fundamentally different. Reductions with radical anions occur in solution, whereas the catalytic reaction occurs on the surface of lithium, which is constantly reactivated by the catalyst, an unconventional catalyst function. The order of relative reactivity is reversed in the two methods as the dominating factor switches from electronic to steric effects of the alkyl substituent. A catalytic amount of N,N‐dimethylaniline (DMA) and Li ribbon can achieve reductive lithiation. DMA is significantly cheaper than alternative catalysts, and conveniently, the Li ribbon does not require the removal of the oxide coating when DMA is used as the catalyst.     

Effect of Cu in electroless Ni–Cu–P coating on passivation process

Electroless Ni–P and Ni–Cu–P coatings were passivated by chromate conversion treatment respectively. The anticorrosive performances of passivated coatings were investigated by potentiodynamic polarization and electrochemical impedance spectroscopy measurements. The passivated Ni–Cu–P coating exhibited a high corrosion resistance with the i_corr of 0.236 μA/cm,² while the value of passivated Ni–P coating was only 1.030 μA/cm,² indicating the passive film could improve the corrosion resistance of Ni–Cu–P coating to a significant extent. High‐resolution X‐ray photoelectron spectroscopy was used to determine the chemical states of elements detected in the passive film. Compared with passivated Ni–P coating, the passive film on Ni–Cu–P coating exhibited a higher ratio of Cr₂O₃ to Cr(OH)₃ with the value of 72:28, which was the main factor for passivated Ni–Cu–P coating showing excellent corrosion resistance. The effect of Cu in electroless Ni–Cu–P coating on passivation process was discussed by the contrast experiment. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis of polyaniline‐modified mesoporous‐silica containers for anticorrosion coatings via in‐situ polymerization and surface‐protected etching

An efficient type of container for anticorrosion coating based on polyaniline (PANI) modified mesoporous silica (pS) sphere has been first prepared via in‐situ polymerization and surface‐protected etching. The PANI‐modified containers not only show higher concentration of loaded inhibitor than pS, but also protect steel well because of the PANI. The coating with 1H‐benzotriazole (BTA) loaded containers shows significant anticorrosion property because of the release of BTA from containers. The structure and morphology of container are characterized by FTIR, XRD, SEM and TEM. The release of BTA from pS and PANI‐modified containers is determined by UV in water. The possible self‐healing anticorrosion performances are evaluated by EIS and polarization curves which indicate that the coating including BTA‐loaded containers performs best. The strategy of modifying pS by PANI is effective and successful. Copyright © 2016 John Wiley & Sons, Ltd.