Adsorption of phenolic compounds onto trimethylstearylammonium surfactant-immobilized cation-exchange membranes

Trimethylstearylammonium hydroxide/methoxide surfactants were immobilized onto two kinds of cation-exchange membranes (P81 and S2001) for the adsorption of phenolic compounds in the present study. The results indicate that the membrane with a doubled cation-exchange capacity (S2001) could attain nearly twice of the immobilized surfactant amount, but its surfactant immobilization % was close to or lower than the one with a smaller cation-exchange capacity (P81). By manipulating the feed surfactant concentration, different surfactant arrangements on the membrane surfaces (such as hemimicellar, admicellar, or mixed structure) could be produced. The membranes with theoretically 100% surfactant immobilization revealed the highest hydrophobicity level, and thus they were applied in the batch adsorption of phenolic compounds. According to the batch adsorption results of four phenolic compounds onto the surfactant-immobilized membranes (100% immobilization), the main adsorption mechanism should be hydrophobic interaction and the order of phenolic compound adsorptivity was phenol < 4-nitrophenol < 4-chloro-3-methylphenol ≤ bisphenol A, identical to their log K_ow order. Moreover, in a batch adsorption/desorption cycle with 100 mL of 1 ppm bisphenol A aqueous sample tested and 5 mL of 2-propanol as the desorbent, the S2001 membrane (100% surfactant immobilization) could completely recover bisphenol A from water at a 20-fold enrichment.     

Adsorption of anionic dye by anionic surfactant modified chitosan beads: Influence of hydrophobic tail and ionic head-group

In this paper, how chitosan hydrogel beads were modified by anionic surfactants (SDS, SDOS, SDBS, AOT, and DTM-12) and then used for the adsorption and removal of an anionic dye (congo red) from aqueous solutions were described. The effect of surfactant concentration, surfactant ionic head-group, and surfactant hydrophobic tail were investigated in detail. The result revealed the modified CS beads all had the obviously higher adsorption capacity than CS beads. Compared to the ionic head-group, the hydrophobic tail of the surfactant plays more important role in the adsorption, and a high adsorption capacity was observed for CS/AOT beads and CS/DTM-12 beads (both with two hydrophobic tails). The Sips isotherm model showed a good fit with the equilibrium experimental data, and the values of the heterogeneity factor (n) indicated heterogeneous adsorption. The adsorption kinetics analysis indicated that the pseudo-second-order rate model could better describe the adsorption process than the pseudo-first-order rate model.     

AFM study on the wettability of mica and graphite modified with surfactant DTAB

In this work atomic force microscopy (AFM) was applied to study the wettability of mica and graphite modified with surfactant dodecyltrimethylammonium bromide (DTAB) at varying DTAB concentrations (below the cmc) and adsorption time. The coverage states of DTAB on surfaces were analyzed from the AFM images, while the contact angle measurement was made for the wettability of DTAB-modified surfaces. The experimental results have shown that the adsorption aggregates formed as needle-like dots covering on the mica surface with the surfactant concentration of 10^?6–10^?4?mol/L. The coverage of DTAB aggregates increased with the increasing concentration, leading to a strong hydrophobicity on the surfaces. However, the large aggregates which might be caused by bilayer adsorption of surfactant occurred on mica surface at surfactant concentration of 10^?3?mol/L, resulting in the reverse of the wettability as the adsorption time extended. In the case of hydrophobic graphite, DTAB aggregates mainly formed as stripe covering on the surfaces, leading to the reduction of hydrophobicity. This reduction became stronger as more DTAB aggregates covered on graphite surfaces.     

正负离子表面活性剂与两性表面活性剂的相互作用

本文研究正负离子表面活性剂与两性表面活性剂混合水溶液的表面性质, 以及两性表面活性剂对正负离子裘面活性剂溶解度的影响。结果表明: (1) 两性表面活性剂的加溶作用,有助于正负离子表面活性剂的溶解; (2) 加入两性表面活性剂的量适当, 混合溶液基本保持原正负离子表面活性剂的表面活性; (3) 正负离子表面活性剂与两性表面活性剂在表面层和胶团中分子间的相互作用比正负离子表面活性剂与非离子表面活性剂分子间的相互作用稍强HC-FC正负; 离子表面活性剂与两性表面活性剂混合体系在表面层中有可能形成双分子或多分子层结构。     

Poly(ethylene glycol) enhances the surface activity of a pulmonary surfactant

The primary role of lung surfactant is to reduce surface tension at the air–liquid interface of alveoli during respiration. Axisymmetric drop shape analysis (ADSA) was used to study the effect of poly(ethylene glycol) (PEG) on the rate of surface film formation of a bovine lipid extract surfactant (BLES), a therapeutic lung surfactant preparation. PEG of molecular weights 3350; 8000; 10,000; 35,000; and 300,000 in combination with a BLES mixture of 0.5 mg/mL was studied. The adsorption rate of BLES alone at 0.5 mg/mL was much slower than that of a natural lung surfactant at the same concentration; more than 200 s are required to reach the equilibrium surface tension of 25 mJ/m². PEG, while not surface active itself, enhances the adsorption of BLES to an extent depending on its concentration and molecular weight. These findings suggest that depletion attraction induced by higher molecular weight PEG (in the range of 8000 to 35,000) may be responsible for increasing the adsorption rate of BLES at low concentration. The results provide a basis for using PEG as an additive to BLES to reduce its required concentration in clinical treatment, thus reducing the cost for surfactant replacement therapy.     

Effect of Molecular Weight on the Interfacial Dilational Viscoelasticity of Anionic Polyelectrolyte/Surfactant Systems

In this article, the effect of molecular weight on the interfacial tension and interfacial dilational viscoelasticity of polystyrene sulfonate/surfactant adsorption films at the water-octane interface have been studied by spinning drop method and oscillating barriers method respectively. The experimental results show that different interfacial behaviors can be observed in different type of polyelectrolyte/surfactant systems. PSS/cationic surfactant CTAB systems show the classical behavior of oppositely charged polyelectrolyte/surfactant systems and can be well explained by electrostatic interaction. Molecular weight of PSS plays a crucial role in the nature of adsorption film. The complex formed by CTAB and higher molecular weight PSS, which has larger dimension and stronger interaction, results in higher dilational modulus at lower surfactant bulk concentration. In the case of PSS/anionic surfactant SDS systems, the co-adsorption of PSS at interface through hydrophobic interaction with alkyl chain of SDS leads to the increase of interfacial tension and the decrease of dilational modulus at lower surfactant bulk concentration. For PSS/nonionic surfactant T × 100 systems, PSS may form a sublayer contiguous to the aqueous phase, which has little effect on interfacial tension but slightly decreases dilational modulus.     

The adsorption structure of nonionic surfactant on the sessile mercury electrode in a thin liquid film

In relation to a colloid stability, the adsorption structure of the Stern layer on a sessile mercury electrode in a thin liquid film of nonionic surfactant was investigated by measuring the double layer capacitance. The Stern capacitance on the electrode in the film could be detected when the measuring frequency used was low, for the resistance of the film was not extremely high but of the order of several thousand ohm. It was found that the adsorption structure of nonionic surfactant in the thin liquid film shows a stratification different from that of bulk.     

Effect of pH on the interfacial adsorption activity of pulmonary surfactant

The effect of pH on the interfacial adsorption activity of pulmonary surfactant was examined. Measurements of the surface tension were made in a Wilhelmy-like surface microbalance specially designed to assay small volumes of hypophase in thermostatically controlled conditions. Alkaline pH caused a significant decrease of the surface activity of both pulmonary surfactant and a lipid extract from surfactant (LES) (containing all of the lipids and surfactant protein-B (SP-B) and surfactant protein-C (SP-C) hydrophobic surfactant proteins, but lacking surfactant protein-A). The pK calculated from the change of surface activity versus pH was 9.18±0.26 and 9.27±0.31 for pulmonary surfactant and LES, respectively. The results from this study support the idea that electrostatic interactions between basic residues of SP-B and SP-C and negatively charged surfactant phospholipids could be important for the interfacial adsorption activity of pulmonary surfactant.     

Compositional Analysis and Adsorption Performance of Surfactants Used for Combined Chemical Flooding

Adsorption of surfactants on reservoir sands in a combined chemical flooding process was investigated using a microcosmic method in order to reveal the effects of surfactant composition on their adsorption. Alkylbenzenesulfonate types of surfactant have been used in this study. The experimental results indicate that surfactant adsorption on the sands heavily depends on its lipophilicity, and the adsorption quantity increases with increasing the lipophilic chain length of the surfactant. It was found that the saturated adsorption could be reached when the concentration of the surfactant was near the critical micelle concentration (CMC). For oilfield applications, the molecular ion peak of the alkylbenzene‐sulfonate type surfactants should concentrate at around C₁₈.     

阴阳离子表面活性剂混合体系在克拉玛依油田中获得超低界面张力

利用阴阳离子表面活性剂复配技术,在克拉玛依油田实际油水体系中获得了超低界面张力.通过添加非离子保护剂的第三组分,阴阳离子表面活性剂混合体系在克拉玛依油田回注水体系中的溶解度大大提高.确定了相关体系能够获得超低界面张力的表面活性剂的浓度和混合的比例范围,在克拉玛依油田的多个实际油水体系中获得了具有较大复配比例和较低表面活性剂浓度的实际配方,其中部分体系油水界面张力可接近10-4mN·m-1.同时,这类阴阳离子表面活性剂混合体系具有很好的抗吸附能力,在石英砂吸附72 h后体系依然呈现优良的超低界面张力.     

阴、阳离子表面活性剂混合体系在硅胶/水及硅胶/矿化水界面上的吸附

研究阴、阳离子表面活性剂混合体系(十二烷基氯代吡啶,辛基磺酸钠,辛基三乙基溴化铵/十二烷基苯磺酸钠)在硅胶,纯水和硅胶,矿化水界面上的吸附作用,探讨阴(阳)离子表面活性剂的存在对阳(阴)离子表面活性剂吸附作用的影响．结果表明,阴离子表面活性剂的存在基本不影响阳离子表面活性剂在带负电固体表面的吸附;而阳离子表面活性剂的存在却使本来吸附量就不大的阴离子表面活性剂在带负电的固体表面上不再吸附．在矿化水中阳离子表面活性剂的吸附量比在纯水中明显降低．从硅胶表面吸附机制解释了所得结果．     

Adsorption of N-Decyl-N,N,N-trimethylammonium triflate (DeTATf), a cationic surfactant, on the Au(111) electrode surface

The adsorption behavior of the cationic surfactant N-decyl-N,N,N-trimethylammonium triflate (DeTATf) on the Au(111) electrode surface was characterized using cyclic voltammetry, differential capacity, and chronocoulometry. The thermodynamics of the ideally polarized electrode have been employed to determine the Gibbs excess and the Gibbs energy of adsorption. The results show that the adsorption of DeTATf has a multistate character. At low bulk DeTATf concentrations, the adsorption state is consistent with the formation of an adsorbed film of nearly flat molecules. At higher concentrations this film may represent a three-dimensional aggregated state. At negative potentials and charge densities close to 0 microC cm-2, the data suggest the formation of a film of tilted molecules oriented with the hydrocarbon tail toward the metal surface and the polar head toward the solution. A surprising result of this study is that DeTATf displays adsorption characteristics of a zwitterionic rather than a cationic surfactant. This behavior indicates that the adsorbed species is an ion pair.     

Modified Calcium Alginate Beads with Sodium Dodecyl Sulfate and Clay as Adsorbent for Removal of Methylene Blue

In present study, we have investigated the effect of an anionic surfactant sodium dodecyl sulfate (SDS) and clay on calcium alginate beads was studied to remove methylene blue (MB) and to improve the adsorption capacity. The effects of various experimental parameters, such as shaking rate, initial dye concentration, temperature, and pH on the adsorption rate, have been studied. Equilibrium studies showed that the sorption of the dye was enhanced in presence of SDS. Scanning electron microscope (SEM) analysis showed that SDS entrapped beads have more pores and cavities which could be responsible for improved adsorption of MB. The kinetics of cationic dye adsorption nicely followed pseudo-second-order process. The evaluated thermodynamic parameters (ΔG ^o, ΔH ^o, ΔS ^o) suggest endothermic adsorption of MB. The results revealed that the surfactant entrapped alginate could be considered as potential adsorbents for MB removal from aqueous solutions.     

Adsorption at the air/water interface in dodecylammonium chloride/sodium dodecyl sulfate mixtures

The composition and properties of the adsorption films of dodecylammonium chloride/sodium dodecyl sulfate at the air/water interface depend on interactions between the film molecules and equilibria in the bulk phase (monomer-micelle and/or monomerprecipitate equilibria).The negative value of surface molecular interaction parameter ^mon calculated using the regular solution theory indicates strong attractive interactions between adsorbed molecules. Electrostatic interactions between oppositely charged ionic head groups enhance the adsorption of surfactants and decrease the minimum molar area of surfactant molecules at the air/water interface. The addition of an oppositely charged surfactant enhances packing at the air/water interface and transition from a liquid expanded to a liquid condensed state. Surface potential measurements reveal positive values for the mixtures investigated, implying the cationic surfactant ions are closer to the surface than the anionic ones.     

表面活性剂改性有机沸石对废水中亚甲基蓝的吸附行为

用表面活性剂十六烷基三甲基溴化铵(CTMAB)和十二烷基硫酸钠(SDS)复合改性沸石,制备了阴阳离子表面活性剂改性沸石,利用X射线衍射和红外吸收光谱表征了改性前后沸石的结构,并研究了改性沸石对亚甲基蓝的吸附行为.结果表明,改性后沸石的吸附性能明显增强;在溶液pH 8、常温,吸附时间100 min、改性沸石用量20 g/...     

The effect of adsorbed carboxymethyl cellulose on the cotton fibre adsorption capacity for surfactant

The research reported in this paper demonstrates that the capacity of cotton fibres to adsorb cationic surfactants as well as the rate of the adsorption process can be increased by adsorbing carboxymethyl cellulose (CMC) onto the fibre surfaces; in addition, the adsorption can be restricted to the fibre surface. CMC was deposited by means of adsorption from an aqueous solution. The adsorption of N-cetylpyridinium chloride (CPC) from an aqueous solution onto the CMC-modified fibres was measured using UV-spectrometric determination of the surfactant concentration in the solution. Adsorption onto the cotton fibres was studied in a weakly basic environment (pH 8.5) where cotton fibres are negatively charged and the CPC ion is positively charged. Modification of the fibres by adsorption of CMC introduces new carboxyl groups onto the fibre surfaces, thereby increasing the adsorption capacity of the fibres for CPC. The initial rate of adsorption of CPC increased proportionally with the amount of charge; however, this rate slowed down at high degrees of coverage on fibres with a high charge. The adsorption of cationic surfactant to the anionic surface groups was stoichiometric, with no indication of multilayer or admicelle formation. It was evident that the acidic group content of the fibres was the primary factor determining cationic surfactant adsorption to these fibres.     

Reactive surfactants in heterophase polymerization: Colloidal properties,film‐water absorption,and surfactant exudation

In this article the results obtained with latexes prepared by emulsion polymerization with a conventional surfactant and a polymerizable surfactant (surfmer) are presented. For this study, well‐defined styrene‐butylacrylate latexes with a conventional nonreactive surfactant (sodium dodecyl sulfate) and a maleate diester surfmer, of which films can be easily cast, were used. The latex with the surfmer was prepared following a surfmer addition strategy to maximize the amount of surfmer bound to the particle surface, and not buried in the particle interior. The latex properties in terms of mechanical stability, film‐water absorption, and film‐surfactant exudation were assessed and compared. The mechanical stability and water‐absorption properties of the latex prepared with surfmer were better than those of the latex with sodium dodecyl sulfate. Additionally, by using a surfmer the surfactant migration to the film‐substrate and film‐air interfaces can be inhibited. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2994–3000, 2002     

气相二氧化硅/季铵Gemini表面活性剂稳定的泡沫体系

以zeta电位法研究了季铵Gemini表面活性剂亚甲基-α, ω-双(十二烷基二甲基溴化铵) (12-s-12, s=2, 6)在水溶液中修饰气相二氧化硅(F-SiO₂)粒子。这些粒子随表面活性剂浓度C增加经历了表面从原先的亲水到疏水再重新亲水的改变,其中疏水粒子可以自发吸附在气泡液膜中,从而很好地稳定泡沫。重新亲水的粒子脱附出液膜,仅留下表面活性剂稳定气泡。强的液膜弹性对应于稳定的泡沫。联接链长度影响了Gemini在F-SiO₂粒子表面的吸附,因而也影响了液膜的弹性和对泡沫的稳定。超短s=2联接链的12-2-12由于反离子解离不完全而带有较少的正电荷,在粒子表面的初始吸附弱于12-6-12,但因此减少了吸附分子头基间的静电排斥,可以形成更致密的吸附层。由于12-2-12本身比12-6-12具有更强的界面吸附能力,F-SiO₂粒子和12-2-12的协同作用可以更好地稳定泡沫体系。     

Properties of mixed protein/surfactant adsorption layers

The adsorption isotherms, adsorption kinetics and surface rheological properties of β-lactoglobulin, β-casein, in the absence and presence of Tween 20 were measured. To study the adsorption process (isotherms and kinetics) at the water–air interface the pendant drop technique (axial drop shape analysis, ADSA), and ring tensiometry were used. The surface shear rheological parameters were measured with a torsion pendulum set-up. Also, data of the equilibrium film thickness and surface diffusion coefficients obtained from fluorescence recovery after photobleaching (FRAP) measurements are used to understand the competitive adsorption mechanism. The adsorption process and shear rheological behaviour of the studied systems show a rather complex behaviour which depends most of all on the system's composition. At high protein or surfactant content the behaviour is controlled by the main component while for the more mixed systems the adsorption process is complex and consists of partial adsorption, surfactant–protein interaction and protein rearrangement as a function of surface coverage. The results obtained illustrate that all these processes must be taken into account in future new theoretical models to be derived for such systems.     

Pressure Effects in Adsorption Systems

A study of the occurrence of large pressure and flow transients when a strongly adsorbed gas is fed to a column which is initially loaded with a lightly adsorbed gas is presented here. Under certain conditions, these transients can cause premature breakthrough and change the shape of the breakthrough curve. This will result in improper estimation of adsorption parameters by the dynamic column loading method and lower apparent adsorption capacity in a full scale unit. A data acquisition system was used to record the pressure and flow transients. An isothermal PDE model developed to study these transients agreed reasonably well with the nonisothermal experimental results. The PDE model predicts that pressure and flow transients will occur during step and pulse~tests conducted to obtain adsorption and mass transfer parameters by the chromatographic method. For instance, lower adsorption capacity will be realized during step tests due to lowering in column pressure. Oscillations were observed when columns are connected in series. The PDE model also predicts these oscillations. Simulations indicate that the extent of oscillations is dependent on the dead volume between columns.