Poly(aryl ether ketone) composite membrane as a high‐performance lithium‐ion batteries separator

We described the design and synthesis of a modified poly(aryl ether ketone) bearing phenolphthalein and allyl groups (P‐PAEK) via nucleophilic polycondensation. A new kind of composite separator, crosslinked P‐PAEK/polyvinylidene fluoride (c‐P‐PAEK/PVDF) membrane was successfully prepared using phase separation, phase inversion method, and UV crosslinking technique. As a separator of lithium‐ion battery, c‐P‐PAEK/PVDF membrane demonstrates high porosity and uniform distribution of pores with interconnected pathways. Low thermal shrinkage, distinct shut‐down effect, high liquid electrolyte uptake capacity, and exciting liquid electrolyte wettability of the prepared c‐P‐PAEK/PVDF membrane have been revealed through comprehensive study. Moreover, the c‐P‐PAEK/PVDF membrane was applied to assemble a conventional Li/LiFePO₄ coin cell, which exhibited hopeful cell performance. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2714–2721     

Facile fabrication of redox‐active and electrochromic poly(amide‐amine) films through electrochemical oxidative coupling of arylamino groups

Two novel electropolymerizable monomers, namely 3,5‐bis(4‐diphenylaminobenzamido)‐N‐[4‐(carbazol‐9‐yl)phenyl]benzamide ( 5 ) and 3,5‐bis(4‐diphenylaminobenzamido)‐N‐[4‐(3,6‐dimethoxycarbazol‐9‐yl)phenyl]benzamide ( 5‐MeO ), were synthesized, and their electrochemical properties were studied by cyclic voltammetry. The electron‐withdrawing amide groups efficiently blocked the radical cations delocalization between the two terminal TPA groups, rendering the electropolymerization of the TPA groups feasible. The polymer electrodeposited from monomer 5 could be further crosslinked through electro‐coupling of the carbazole groups, which showed both electrochromic and fluorescent properties (the emission of blue light (460 nm) in solid state). Both of the electro‐generated polymer films derived from 5 and 5‐MeO showed reversible electrochemical oxidation processes in the range of 0 ? 1.4 V with strong color changes and high contrast ratios in the visible and NIR regions upon electro‐oxidation. © 2016 The Authors. Journal of Polymer Science Part A: Polymer Chemistry Published by Wiley Periodicals, Inc. 2016, 54, 2476–2485     

Water adsorption on the surface of Ni‐ and Co‐based layer‐structured cathode materials for lithium‐ion batteries

Ni‐based layer‐structured cathode materials are more vulnerable to moisture than conventional LiCoO₂ cathodes, adsorbing more water and easily forming LiOH on the surface. This study investigated the moisture adsorption mechanism on the surface of layer‐structured cathodes. The behavior of water molecules on LiCoO₂ and LiNiO₂ surfaces were simulated and the structural and chemical changes during the adsorption process were analyzed by first‐principles methods. It was found that the adsorption occurs via two types of mechanism: one involving ionic interactions between Li on the crystal surface and O in the adsorbate, and the other involving covalent bonding between the transition metal (TM) on the surface and O in the adsorbate, which restores the coordination of the TM by recovering its broken bonds. The difference between the water adsorption behaviors of Ni‐based and Co‐based layer‐structured cathodes was found to be mainly due to the ionic‐interaction‐driven adsorption on the (003) surface.     

Semi‐Interpenetrated Hydrogels‐Microfibers Electroactive Assemblies for Release and Real‐Time Monitoring of Drugs

Simultaneous drug release and monitoring using a single polymeric platform represents a significant advance in the utilization of biomaterials for therapeutic use. Tracking drug release by real‐time electrochemical detection using the same platform is a simple way to guide the dosage of the drug, improve the desired therapeutic effect, and reduce the adverse side effects. The platform developed in this work takes advantage of the flexibility and loading capacity of hydrogels, the mechanical strength of microfibers, and the capacity of conducting polymers to detect the redox properties of drugs. The engineered platform is prepared by assembling two spin‐coated layers of poly‐γ‐glutamic acid hydrogel, loaded with poly(3,4‐ethylenedioxythiophene) (PEDOT) microparticles, and separated by a electrospun layer of poly‐ε‐caprolactone microfibers. Loaded PEDOT microparticles are used as reaction nuclei for the polymerization of poly(hydroxymethyl‐3,4‐ethylenedioxythiophene) (PHMeDOT), that semi‐interpenetrate the whole three layered system while forming a dense network of electrical conduction paths. After demonstrating its properties, the platform is loaded with levofloxacin and its release monitored externally by UV–vis spectroscopy and in situ by using the PHMeDOT network. In situ real‐time electrochemical monitoring of the drug release from the engineered platform holds great promise for the development of multi‐functional devices for advanced biomedical applications.     

High capacity and cycling stability of poly(diaminoanthraquinone) as an organic cathode for rechargeable lithium batteries

Poly(1,5‐diaminoanthraquinone) is synthesized by oxidative polymerization of diaminoanthraquinone monomers and investigated as an organic host for Li‐storage reaction. Benefiting from its high density of redox‐active, Li⁺‐associable benzoquinone groups attached to conducting polyaniline backbones, this polymer undergoes its cathodic reaction predominately through Li⁺‐insertion/extraction processes, delivering a very high reversible capacity of 285 mAh g^?1. In addition, the PDAQ polymer cathode exhibits an excellent rate capability (125 mAh g^?1 at 800 mA g^?1) and a considerable cyclability with a capacity retention of ～160 mAh g^?1 over 200 cycles, possibly serving as a sustainable, high capacity Li⁺ host cathode for Li‐ion batteries. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 235–238     

Electrochemical synthesis of poly(3‐methylthiophene): A kinetic study

Poly(3‐methylthiophene) (P3MT) films were electrogenerated on both platinum and carbon‐felt working electrodes. The kinetic equation was determined by the monomer and electrolyte concentrations being changed for different reaction times. For each sample, the weight of the polymer obtained was measured along with the polymerization charge, the oxidation charge, the ratio (R) between the two magnitudes, the charge storage efficiency (SE), and the doping level. The results obtained from the kinetic study indicate significant electrolyte participation in the electropolymerization process. The SE and the doping level decreased inversely proportionately to both the reaction time and the concentrations of the monomer and electrolyte. The ratio R increased with reaction time as well as with monomer or electrolyte concentrations for all P3MTs generated on the carbon‐felt electrodes, whereas for those films generated on platinum electrodes, the highest values were obtained for the lowest monomer and electrolyte concentrations. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1258–1266, 2000     

Silicone‐urethane membranes for lithium batteries. Part 1. Moisture‐cured poly(siloxane‐urethane‐urea) elastomers containing polyethylene oxide (PEO) segments – synthesis and characterization as potential membrane materials

Poly(siloxane‐urethane‐urea) elastomers containing both polysiloxane and polyethylene oxide (PEO) segments in the polymer chain were obtained by moisture‐curing of NCO‐terminated poly(siloxane‐urethane) prepolymers synthesized from isophorone diisocyanate and mixtures of polyoxyethylene diols and polysiloxane diols with various molecular weights. Mechanical properties of the moisture‐cured films and their swelling ability in solvent mixtures commonly used in lithium batteries were investigated, and it was found that they were greatly influenced by PEO content in the polymer. PEO content in the polymer was also found to affect very much the electric conductivity of the films after immersion in lithium salt solution in ethylene carbonate–dimethyl carbonate solvent mixture. At high contents of PEO in the polymer chain specific conductivities of the films in a range of 10^?3, Scm^?1 could be achieved at room temperature. Based on the results of Scanning Electron Microscopy with X‐ray Analysis (SEM/EDS) investigations and wide‐angle X‐ray scattering and small‐angle X‐ray scattering studies, it could be anticipated that the reason for good conductivity of the films might be their specific supramolecular structure that potentially facilitated lithium ion mobility. Copyright © 2015 John Wiley & Sons, Ltd.     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Synthesis and Characterization of Star‐Shaped Diblock Poly(ε‐caprolactone)/Poly(ethylene oxide) Copolymers

Summary: Star‐shaped hydroxy‐terminated poly(ε‐caprolactone)s (ssPCL), with arms of different lengths, were obtained by ring‐opening polymerization (ROP) of ε‐caprolactone initiated by pentaerythritol, and were condensed with α‐methyl‐ω‐(3‐carboxypropionyloxy)‐poly(ethylene oxide)s ( = 550–5 000) to afford four‐armed PCL‐PEO star diblock copolymers (ssPCL‐PEO). The polymers were characterized by ¹H and ¹³C NMR spectroscopy and size‐exclusion chromatography (SEC). The melting behavior of ssPCLs was studied by differential scanning calorimetry (DSC). X‐ray diffraction and DSC techniques were used to investigate the crystalline phases of ssPCL‐PEOs.

The part of the synthesis of four‐armed star‐shaped diblock poly(ε‐caprolactone)‐poly(ethylene oxide) copolymers as described.     

Conductive and optical properties of PPV modified by N+ ion implantation

In this article, a soluble poly[2‐methoxy‐5‐(3′‐methyl)butoxy]‐p‐phenylene vinylene (MMB‐PPV) was synthesized by dehydrochlorination reaction and the MMB‐PPV film was implanted by nitrogen ions (N⁺) with the ion dose and energy in the range of 3.8 × 10¹⁵ to 9.6 × 10¹⁶ ions/cm² and 15–35 keV, respectively. The surface conductivity, optical absorption, optical band gap (E_g) of modified MMB‐PPV film were studied, and the third‐order nonlinear optical susceptibility (χ⁽³⁾) as well as its environmental stability of modified MMB‐PPV film were also measured by degenerate four‐wave mixing system. The results showed that the surface conductivity of MMB‐PPV film was up to 3.2 × 10^?2 S when ion implantation was performed with the energy of 35 keV at an ion dose of 9.6 × 10¹⁶ ions/cm², which was seven order of magnitude higher than that of the pristine film. UV‐Vis absorption spectra demonstrated that the optical absorption of MMB‐PPV film was enhanced gradually in the visible region followed by a red shift of optical absorption threshold and the E_g value was reduced from 2.12 eV to 1.59 eV with the increase of ion dose and energy. The maximum χ⁽³⁾ value of 2.45 × 10^?8 esu for modified MMB‐PPV film was obtained with the ion energy of 20 keV at an ion dose of 3.8 × 10¹⁶ ions/cm², which was almost 33 times larger than that for pristine film. In comparison to the reduction of 17% in the χ⁽³⁾ value of pristine MMB‐PPV film, the maximum χ⁽³⁾ value of 2.45 × 10^?8 esu for modified MMB‐PPV film decreased by over 5.3% when they had been exposed under the same ambient conditions for 90 days. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2072–2077, 2010     

Control of all‐conjugated block copolymer crystallization via thermal and solvent annealing

Control of the crystallization of conjugated polymers is of critical importance to the performance of organic electronics, such as organic photovoltaic devices, due to the effect on charge separation and transport, particularly for all‐polymer devices. The block copolymer poly(3‐dodecylthiophene)‐block‐poly(9,9‐dioctylfluorene) (P3DDT‐b‐PF), which has matched crystallization temperatures for each block, is used to study the effects of processing history on resulting crystallization. For longer annealing times and rapid quenching to room temperature, P3DDT crystals are preferred whereas for shorter annealing times and slower quenching, PF crystals are preferred. Both crystal forms are evidenced for long annealing time and slow quenching. Additionally, for room temperature annealing in the presence of a chloroform vapor, PF crystals are found in the PF β phase with the predominant crystal peak oriented perpendicular to the thermally annealed case. These results will provide guidance for optimizing annealing strategies for future donor/acceptor block copolymer photovoltaic devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 900–906     

Discrete Metal Catalysts for Stereoselective Ring‐Opening Polymerization of Chiral Racemic β‐Lactones

Poly(β‐hydroxyalkanoate)s (PHAs) are a class of aliphatic polyesters that can be efficiently synthesized by ring‐opening polymerization (ROP) of β‐lactones. The case of chiral racemic β‐substituted β‐lactones is particularly appealing since these monomers open the way to original tacticities and materials different from those biotechnologically produced. In this overview, after briefly surveying general considerations associated to the ROP of β‐lactones and metal‐based catalysts used in stereoselective ROP of racemic β‐butyrolactone, special emphasis is given to discrete rare earth catalysts that have allowed the preparation of highly syndiotactic poly(3‐hydroxybutyrate)s. Recent developments – such as preparation of stereocontrolled PHAs with pendant structural groups via (co)polymerization of functional β‐substituted β‐lactones, and highly alternating copolymers obtained by ROP of mixtures of enantiomerically pure but different monomers – are also discussed.

     

Molecular composites composed of castor oil‐modified poly(ε‐caprolactone) and self‐assembled hydroxystearic acid fibers

After (R)‐12‐hydroxystearic acid (HSA) was mixed at 100 °C with the castor oil‐modified poly(ε‐caprolactone) (CO‐PCL) prepared by the ring‐opening polymerization of ε‐caprolactone in the presence of castor oil, the mixture was gradually cooled to room temperature to give a solidified CO‐PCL/HSA composite. The CO‐PCL/HSA sample showed an exothermic peak at around 67–71 °C which was lower than the melting point of HSA (76.8 °C), indicating the formation of mesogenic HSA aggregates. The rheological measurement of the CO‐PCL/HSA revealed the formation of HSA organogel at around 67–55 °C during the cooling process from the melt. Furthermore, the polarized and normal optical microscopic analyses of CO‐PCL/HSA on the cooling stage revealed that anisotropic fibrous materials are formed at around 60 °C and then the fibrous network propagated over the matrix polymer. The flexural modulus and storage modulus of the CO‐PCL/HSA composite increased with increasing HSA content. The CO‐PCL/HSA composite annealed at 60 °C for 2 h on the cooling process had a higher flexural and storage modulus than the sample without annealing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1281–1289, 2010     

Poly(ε‐caprolactone)–poly(isobutylene): A crystallizing,hydrogen‐bonded pseudo‐block copolymer

The crystallization of block copolymers (BCPs) under homogeneous and heterogeneous nucleation is currently well understood revealing the strong interplay of crystallization in competition to microphase separation. This article reports investigations on synthesis and crystallization processes in weakly interacting supramolecular pseudo‐BCPs, composed of poly(ε‐caprolactone) (PCL) and poly(isobutylene) (PIB) blocks, connected by a specifically interacting hydrogen bond (thymine/2,6‐diaminotriazine). Starting from ring opening polymerization of ε‐caprolactone, the use of “click”‐chemistry enabled the introduction of thymine endgroups onto PCL polymer, thus generating the fully thymine‐substituted pure PCLs ( 1a , 1b ) as judged via NMR and MALDI analysis. Physical mixing of 1a , 1b with a bivalent, bis(2,6‐diaminotriazine)‐containing molecule ( 2 ) generated the bivalent polymers BC1 and BC2 , whereas mixing of 1a or 1b with the 2,6‐diaminotriazine‐substituted PIB ( 3 ) generated the supramolecular pseudo‐BCPs BC3 and BC4 . Thermal investigations (DSC, Avrami analysis) revealed only minor changes in the crystallization behavior of BC1 – BC4 with Avrami exponents close to three, indicative of a confluence of the growing crystals during the crystallization process. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of four‐armed poly(ε‐caprolactone)‐block‐poly(ethylene oxide) by diethylzinc catalyst

Biodegradable, amphiphilic, four‐armed poly(?‐caprolactone)‐block‐poly(ethylene oxide) (PCL‐b‐PEO) copolymers were synthesized by ring‐opening polymerization of ethylene oxide in the presence of four‐armed poly(?‐caprolactone) (PCL) with terminal OH groups with diethylzinc (ZnEt₂) as a catalyst. The chemical structure of PCL‐b‐PEO copolymer was confirmed by ¹H NMR and ¹³C NMR. The hydroxyl end groups of the four‐armed PCL were successfully substituted by PEO blocks in the copolymer. The monomodal profile of molecular weight distribution by gel permeation chromatography provided further evidence for the four‐armed architecture of the copolymer. Physicochemical properties of the four‐armed block copolymers differed from their starting four‐armed PCL precursor. The melting points were between those of PCL precursor and linear poly(ethylene glycol). The length of the outer PEO blocks exhibited an obvious effect on the crystallizability of the block copolymer. The degree of swelling of the four‐armed block copolymer increased with PEO length and PEO content. The micelle formation of the four‐armed block copolymer was examined by a fluorescent probe technique, and the existence of the critical micelle concentration (cmc) confirmed the amphiphilic nature of the resulting copolymer. The cmc value increased with increasing PEO length. The absolute cmc values were higher than those for linear amphiphilic block copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 950–959, 2004     

Preparation and ion conductivities of the plasticized polymer electrolytes based on the poly(acrylonitrile‐ co‐lithium methacrylate)

The polymer electrolytes composed of poly(acrylonitrile‐co‐lithium methacrylate) [P(AN‐co‐LiMA)], ethylene carbonate (EC), and LiClO₄ salts have been prepared. The ion groups in the P(AN‐co‐LiMA) were found to prevent EC from crystallization through their ion–dipole interactions with the polar groups in the EC. This suppression of the EC crystallization could lead to the enhancement of the ion conductivity at subambient temperature. The polymer electrolytes based on the PAN ionomer with 4 mol % ion content exhibited ion conductivities of 2.4 × 10⁻⁴ S/cm at −10°C and 1.9 × 10⁻³ S/cm at 25°C by simply using EC as a plasticizer. In the polymer electrolytes based on the PAN ionomer, ion motions seemed to be coupled with the segmental motions of the polymer chain due to the presence of the ion–dipole interaction between the ion groups in the ionomer and the polar groups in the EC, while the ion transport in the PAN‐based polymer electrolytes was similar to that of the liquid electrolytes. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 247–252, 1999     

Metal‐ and solvent‐free,clickable synthesis and postpolymerization functionalization of poly(triazole)s

In this study, a series of linear poly(triazole)s (PTAs) were successfully synthesized by the metal‐ and solvent‐free, thermal click polymerization of diazide and dialkyne (A₂ + B₂) monomers. All click polymerizations proceeded smoothly at 80 °C in an open atmosphere without protection from oxygen and moisture. After being polymerized for 36 h, the crude polymer was further fractionated into three fractions using a multistep precipitation method. By selectively choosing precipitating agents, this process produced poly(triazole) fractions with low polydispersity index (<1.30). The resulting PTAs are soluble in common organic solvents and stable at a temperature up to 320 °C. Furthermore, the methyl benzoate moieties in the main chain can serve as useful building blocks for further postpolymerization functionalization, yielding 1,2,4‐triazole derivatives. This functionalization strategy offers potential for the development of novel triazole‐based materials. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Multiple Sol‐Gel Transitions of PEG‐PCL‐PEG Triblock Copolymer Aqueous Solution

An aqueous solution of a poly(ethylene glycol)‐polycaprolactone‐poly(ethylene glycol) (PEG‐PCL‐PEG) with a composition of EG₁₃CL₂₃EG₁₃ undergoes multiple transitions, from sol‐to‐gel (hard gel)‐to‐sol‐to‐gel (soft gel)‐to‐sol, in the concentration range 20.0∼35.0 wt.‐%. Through dynamic mechanical analysis, UV‐vis spectrophotometry, small angle X‐ray scattering, differential scanning calorimetry, microcalorimetry and ¹³C NMR spectroscopy, the mechanism of these transitions was investigated. The hard gel and soft gel are distinguished by the crystalline and amorphous state of the PCL. The extent of PEG dehydration and the molecular motion of each block also played a critical role in the multiple transitions. This paper suggests a new mechanism for these multiple transitions driven by temperature changes.

     

Synthesis of High Molecular Weight Cyclic Poly(ε‐caprolactone)s of Variable Ring Size Based on a Light‐Induced Ring‐Closure Approach

High molecular weight cyclic poly(ε‐caprolactone)s (cPCLs) with variable ring size are synthesized via light‐induced ring closure of α,ω‐anthracene‐terminated PCL (An‐PCL‐An). The ring size of cPCL is tunable simply by adjusting the polymer concentration from 10 to 100 mg mL⁻¹ in THF. The cyclo­addition via the bimolecular cyclization of An‐PC‐An is well characterized by a variety of analyses such as ¹H NMR and UV–vis spectroscopies, gel‐permeation chromatography, and differential scanning calorimetry. The reversible dimerization of An induced by heating enables the cyclic PCL to have a switchable “on–off” capability. This novel light‐induced ring‐closure technique can be one of the most powerful candidates for producing various well‐defined cyclic polymers in highly concentrated polymer solution.