Dielectric and conductivity processes in poly(ethylene terephthalate) and poly(ethylene naphthalate) homopolymers and copolymers

Electrical relaxation and conductivity processes in amorphous and semicrystalline poly(ethylene terephthalate) (PET) and poly(ethylene naphthalate) (PEN) homopolymers and certain PET/PEN copolymers have been studied by means of dielectric spectroscopy. Homopolymers and copolymers able to crystallize were subjected to successive thermal runs to investigate the influence of the thermal history upon the morphology and the electrical behavior of the polymeric systems. The morphology of the untreated as well as the heat‐treated specimens was determined by means of Differential Scanning Calorimetry (DSC). All samples exhibit β‐relaxation process, due to local motions of the C?O polar side groups, and α‐relaxation process associated to the glass/rubber transition. In the PEN spectrum an additional, subglass, mode was recorded, most probably attributed to cooperative motions of the naphthalene groups. Finally, the dynamic nature of the crystallization process is expressed via the over glass transition mode and the temperature dependence of dc conductivity recorded in amorphous PET, PEN, and PET/PEN (85/15) (wt/wt) samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3078–3092, 2006     

Strategies toward biocompatible artificial implants: Grafting of functionalized poly(ethylene glycol)s to poly(ethylene terephthalate) surfaces

Epoxide and aldehyde end‐functionalized poly(ethylene glycol)s (PEGs) (M_w = 400, 1000, 3400, 5000, and 20,000) were grafted to poly(ethylene terephthalate) (PET) film substrates that contained amine or alcohol groups. PET‐PAH and PET‐PEI were prepared by reacting poly(allylamine) (PAH) and polyethylenimine (PEI) with PET substrates, respectively; PET‐PVOH was prepared by the adsorption of poly(vinyl alcohol) (PVOH) to PET substrates. Grafting was characterized and quantified by the increase of the intensity of the PEG carbon peak in the X‐ray photoelectron spectra. Grafting yield was optimized by controlling reaction parameters and was found to be substrate‐independent in general. Graft density consistently decreased as PEG chain length was increased. This is likely due to the higher steric requirement of higher molecular weight PEG molecules. Water contact angles of surfaces containing long PEG chains (3400, 5000, and 20,000) are much lower than those containing shorter PEG chains (400 and 1000). This indicates that longer PEG chains are more effective in rendering surfaces hydrophilic. Protein adsorption experiments were carried out on PET‐ and PEG‐modified derivatives using collagen, lysozyme, and albumin. After PEG grafting, the amount of protein adsorbed was reduced in all cases. Trends in surface requirements for protein resistance are: surfaces with longer PEG chains and higher chain density, especially the former, are more protein resistant; PEG grafted to surfaces containing branched or network polymers is not effective at covering the underlying substrate, and thus does not protect the entire surface from protein adsorption; and substrates containing surface charge are less protein‐resistant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5389–5400, 2004     

Surface characterization of plasma‐modified poly(ethylene terephthalate) film surfaces

Poly(ethylene terephthalate) (PET) film surfaces were modified by argon (Ar), oxygen (O₂), hydrogen (H₂), nitrogen (N₂), and ammonia (NH₃) plasmas, and the plasma‐modified PET surfaces were investigated with scanning probe microscopy, contact‐angle measurements, and X‐ray photoelectron spectroscopy to characterize the surfaces. The exposure of the PET film surfaces to the plasmas led to the etching process on the surfaces and to changes in the topography of the surfaces. The etching rate and surface roughness were closely related to what kind of plasma was used and how high the radio frequency (RF) power was that was input into the plasmas. The etching rate was in the order of O₂ plasma > H₂ plasma > N₂ plasma > Ar plasma > NH₃ plasma, and the surface roughness was in the order of NH₃ plasma > N₂ plasma > H₂ plasma > Ar plasma > O₂ plasma. Heavy etching reactions did not always lead to large increases in the surface roughness. The plasmas also led to changes in the surface properties of the PET surfaces from hydrophobic to hydrophilic; and the contact angle of water on the surfaces decreased. Modification reactions occurring on the PET surfaces depended on what plasma had been used for the modification. The O₂, Ar, H₂, and N₂ plasmas modified mainly CH₂ or phenyl rings rather than ester groups in the PET polymer chains to form C? O groups. On the other hand, the NH₃ plasma modified ester groups to form C? O groups. Aging effects of the plasma‐modified PET film surfaces continued as long as 15 days after the modification was finished. The aging effects were related to the movement of C?O groups in ester residues toward the topmost layer and to the movement of C? O groups away from the topmost layer. Such movement of the C?O groups could occur within at least 3 nm from the surface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3727–3740, 2004     

Isolation and identification of cyclic oligomers of the poly(ethylene terephthalate)–poly(ethylene isophthalate) copolymer

New cyclic oligomers of the copolymer of poly(ethylene terephthalate) (PET) and poly(ethylene isophthalate) (PEI) were isolated and identified. A condensation polymerization was carried out at a high temperature, and the solid‐state polymerization that followed yielded the high molecular weight polymer. The oligomers were extracted from the high molecular weight PET–PEI copolymer and separated with preparative high performance liquid chromatography techniques. Their chemical structures and properties were analyzed and determined by ¹H NMR, differential scanning calorimetry, and mass spectroscopy. The oligomers observed at early retention times were a cyclic dimer and cyclic trimers and consisted of [GT]₃, [GI]₂, [GI]₃, [GT]₂[GI]₁, and [GT]₁[GI]₂. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 881–889, 2003     

Organocatalytic depolymerization of poly(ethylene terephthalate)

We describe the organocatalytic depolymerization of poly(ethylene terephthalate) (PET), using a commercially available guanidine catalyst, 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD). Postconsumer PET beverage bottles were used and processed with 1.0 mol % (0.7 wt %) of TBD and excess amount of ethylene glycol (EG) at 190 °C for 3.5 hours under atmospheric pressure to give bis(2‐hydroxyethyl) terephthalate (BHET) in 78% isolated yield. The catalyst efficiency was comparable to other metal acetate/alkoxide catalysts that are commonly used for depolymerization of PET. The BHET content in the glycolysis product was subject to the reagent loading. This catalyst influenced the rate of the depolymerization as well as the effective process temperature. We also demonstrated the recycling of the catalyst and the excess EG for more than 5 cycles. Computational and experimental studies showed that both TBD and EG activate PET through hydrogen bond formation/activation to facilitate this reaction. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Preparation and characterization of poly(butylene terephthalate)/poly(ethylene terephthalate) copolymers via solid‐state and melt polymerization

To increase the T_g in combination with a retained crystallization rate, bis(2‐hydroxyethyl)terephthalate (BHET) was incorporated into poly(butylene terephthalate) (PBT) via solid‐state copolymerization (SSP). The incorporated BHET fraction depends on the miscibility of BHET in the amorphous phase of PBT prior to SSP. DSC measurements showed that BHET is only partially miscible. During SSP, the miscible BHET fraction reacts via transesterification reactions with the mobile amorphous PBT segments. The immiscible BHET fraction reacts by self‐condensation, resulting in the formation of poly(ethylene terephthalate) (PET) homopolymer. ¹H‐NMR sequence distribution analysis showed that self‐condensation of BHET proceeded faster than the transesterification with PBT. SAXS measurements showed an increase in the long period with increasing fraction BHET present in the mixtures used for SSP followed by a decrease due to the formation of small PET crystals. DSC confirmed the presence of separate PET crystals. Furthermore, the incorporation of BHET via SSP resulted in PBT‐PET copolymers with an increased T_g compared to PBT. However, these copolymers showed a poorer crystallization behavior. The modified copolymer chain segments are apparently fully miscible with the unmodified PBT chains in the molten state. Consequently, the crystal growth process is retarded resulting in a decreased crystallization rate and crystallinity. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 882–899, 2007.     

UV curing of a novel resin derived from poly(ethylene terephthalate)

The synthesis and characterization of photopolymerizable unsaturated polyester resins based on PET waste are described. The resins came from a depolymerization process based on the glycolysis of PET by diethylene glycol (DEG). Different molecular weights of glycolysates were synthesized. Then, the latter was functionalized by a methyl hemiester of maleic acid to obtain unsatured α,ω‐bismaleate PET oligomers. In the presence of an electron donor monomer, such as triethylene glycol divinyl ether, these electron acceptor oligomers were copolymerized by way of charge‐transfer complexes under UV irradiation. The reaction was monitored in situ by real‐time IR spectroscopy to study the kinetics of photopolymerization. This one was studied in relation with the physical and chemical characteristics of oligoesters and the composition of mixtures containing divinyl ethers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1324–1335, 2007     

The triple melting behavior of poly(ethylene terephthalate): Molecular weight effects

The melting behavior of isothermally crystallized PET has been studied using linear heating in a differential scanning calorimeter (DSC). Variables such as crystallization temperature, crystallization time, heating rate, and average molecular weight are the main focus of the study. On the basis of several experimental techniques, a correlation of the melting behavior of PET with the amount of secondary crystallization was found to exist. It was observed that the triple melting of PET is a function of programmable DSC variables such as crystallization temperature, crystallization time, and heating rate. However, in testing the hypothesis that there was a correlation between melting endotherms and secondary crystallization inside spherulites, it was found necessary to use a DSC-independent variable in order to enhance the observed effects. Therefore, on the basis of a crystallization model that involves secondary branching along the edges of parent lamellar structures, it was speculated that an increase in the average molecular weight could affect the triple melting of PET due to an increase of rejected portions of the macromolecules. It was found that the second melting endotherm increased, apparently, at the expense of the third one as the average molecular weight was increased. The second melting endotherm was also found to correlate proportionally with the amount of secondary crystallization inside spherulites. The results support a model of crystallization which basically consists of parent crystals and at least one population of secondary, probably metastable, crystals. This latter structural component must involve excluded portions of the macromolecules that did not crystallize during the isothermal crystallization period of the parent crystals. An increase of molecular weight gives rise to a higher entanglement density which in turn increases the fraction of initially rejected chain sections and therefore the amount of secondary crystallization. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1757–1774, 1997     

Alkyd resins derived from glycolized waste poly(ethylene terephthalate)

In this investigation the production of secondary value-added products, such as alkyd resins, derived from the glycolysis of poly(ethylene terephthalate) (PET) is examined as an effective way for its recycling. PET was taken from common soft-drink bottles and diethylene glycol (DEG) was used for the depolymerization at several initial molar ratios. The oligomers obtained were analyzed according to their average molecular weights. Furthermore, the glycolyzed PET products (oligomers) were reacted with maleic anhydride, phthalic anhydride and propylene glycol to form unsaturated polyester resins. These were subsequently mixed with styrene and cured using the benzoyl peroxide/amine initiator system to carry out the reaction in ambient temperature. The curing characteristics of the resins produced were investigated with respect to the initial molar ratio of DEG/PET as well as the initial initiator concentration. Finally, the mechanical properties (tensile strength and elongation at the break point) of the resins were compared with the conventional general purpose resin and were found to be comparable.     

Comparison of the catalytic activity of PHB–depolymerase,yeast lipase,and papain on poly(ethylene adipate), poly(ethylene succinate), and poly (3-hydroxybutyric acid)-co-(3-hydroxyvaleric acid)

PHB-depolymerase degraded poly[(3-hydroxybutyric acid)-co-(3-hydroxyvaleric acid)] (PHB/V) significantly. No other enzyme used in this study showed activity toward PHB/V. Weight loss and gel permeation chromatography (GPC) studies suggested that enzymatic degradation takes place by a surface erosion mechanism. pH studies demonstrated that enzymatic degradation occurs even when little weight loss is observed. Differential scanning calorimetry (DSC) analysis demonstrated that the enzymes studied prefer to degrade amorphous regions. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2581–2585, 1999     

Synthesis and hydrolytic degradation of poly(ethylene succinate) and poly(ethylene terephthalate) copolymers

The conditions of synthesis of statistical poly(ethylene succinate-co-terephthalate) copolymers (2GTS) and high molecular weight poly(ethylene succinate) (PES) with good hydrolytic and optical parameters, designed for the production of biodegradable products and resins, are presented in this article. Copolymers were prepared by melt polycondensation of bis-(β-hydroxyethylene terephthalate) (BHET) and succinic acid (SA) with excess of ethylene glycol (2G) in the presence of a novel titanium/silicate catalyst (C-94) and catalytic grade of germanium dioxide (GeO₂) as cocatalyst. The chemical structure and physical properties of those materials were characterized by ¹H NMR, FT-IR, dynamical-mechanical thermal analyses (DMTA), differential scanning calorimetry (DSC), solution viscosity and spectroscopic methods. The hydrolytic degradation was performed in a water solution with variable pH, also in garden soil and in compost. The highest hydrolytic degradation rate was observed for pH 4 and for compost. Better hydrolytic degradation values in compost medium were observed for copolyester prepared in the presence of GeO₂ as polycondensation cocatalyst. The copolyester with 40 mol% of aliphatic units was chosen for industrial syntheses which were performed in ELANA and subsequently the processing parameters and compatibility with potato starch of this polyester were checked by BIOP Biopolymer Technologies AG.     

Colour formation in poly(ethylene terephthalate) during melt processing

The discolouration, that occurs in virgin poly(ethylene terephthalate) - PET during melt processing, was studied using various bulk and surface analytical techniques. Proton nuclear magnetic resonance (¹H NMR) was used to study the bulk chemical changes occurring in the polymer during thermo-oxidative degradation. Chemical derivatisation with trifluoroacetic anhydride (TFAA) was used to label the hydroxyl groups introduced on the polymer surface by thermal oxidation.From the surface analysis studies using photoacoustic Fourier transform infrared spectroscopy (PA/FT-IR), diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) and X-ray photoelectron spectroscopy (XPS) it was evident that colour formation starts initially with the hydroxylation of the terephthalic ring. Further, the formation of additional carbonyl functionalities and conjugated chromophoric systems complete the colour formation process.     

Anisotropic properties of poly(ethylene terephthalate) by Brillouin spectroscopy: Anisotropic properties of oriented bulk and nanostructured poly(ethylene terephthalate) determined by Brillouin spectroscopy and birefringence experiments

Using Brillouin spectroscopy (BS), the tensor of the elastic constants of oriented poly(ethylene terephthalate) was determined for a variety of morphologies obtained by different uniaxial drawing procedures. The extreme values of the moduli along the drawing direction at frequencies of a few gigahertz were C₃₃ = 40 GPa and C₄₄ = 1.8 GPa. As a result of the invariants of the single‐phase aggregate model, the oriented state is dominated by the Reuss average even at extreme draw ratios and subsequent to a deformation‐induced crystallization. This is documented in both the BS orientation parameter and the BS mode numbers in comparison with birefringence. Additional spectral lines observed at draw ratios larger than 6 are discussed in relation to the formation of nanostructured phases. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1201–1213, 2002     

Solvent and concentration effects on the properties of electrospun poly(ethylene terephthalate) nanofiber mats

This study describes the preparation and characterization of nanofibrous mats obtained by electrospinning poly(ethylene terephthalate) (PET) solutions in trifluoroacetic acid/dichloromethane (TFA/DCM). Special attention was paid to the effect of polymer concentration and solvent properties on the morphology, structure, and mechanical and thermal properties of the electrospun nonwovens. The results show that the spinnable concentration of PET solution in TFA/DCM solvents is above 10 wt %. Mats have nanofibrous morphology with fibers having an average diameter in the range of 200–700 nm (depending on polymer concentration and solvent composition) and an interconnected pore structure. Higher solution concentration favors the formation of uniform fibers without beads and with higher diameter. Morphology and fiber assembly changed with the solvent properties. Solvent mixtures rich in TFA, i.e., those with higher dielectric constant and lower surface tension, originated fibers with small diameter. However, due to the lower volatility, those solvent mixtures also produced more branched and crosslinking fibers, with less morphologic uniformity. Mechanical properties (Young's modulus, ultimate strength, and elongation at break) and thermal properties (glass transition, crystallization, and melting) have been studied for the PET electrospun nanomats and compared with those of the original polymer. Solvent effect on fiber crystallinity was not significant, but a complex effect was observed on the mechanical properties of the electrospun mats, as a consequence of the different structural organization of the fibers within the mat network. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 460–471, 2008     

Alkaline-solution-induced crystallization in poly(butylene terephthalate)

Subtle crystalline structure changes of poly(butylene terephthalate) (PBT) specimens treated with an alkali solution at room temperature were investigated with the grazing incidence X-ray diffraction (GIXRD) analysis method. A new phenomenon was found: the aqueous alkali solution induced the crystallization of the PBT polymer. Under the GIXRD analysis condition of an incidence angle of 1°, the penetration depth of the X-ray in PBT was less than 80 μm, and this agreed well with the rough theoretical estimation. The alkali solution adopted in this study was an aqueous sodium hydroxide solution, which had a concentration of 2.5 N. Dissolved quantities of the surface layers during the alkaline treatment were found to be small. No appreciable intrinsic viscosity change due to the alkaline treatment was detected. Possible factors that might contribute to the crystallization, such as water absorption and a chemical reagent effect, were examined, and a plausible explanation for the phenomenon was developed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1938–1948, 2004     

Characterization and degradation behavior of poly(butylene adipate‐co‐terephthalate)s

Random copolyesters based on 1,4‐butanediol and different ratios between adipic and terephthalic units were synthesized from thermal polycondensation of the appropriate mixture of monomers or by melt transesterification of the mixture of homopolymers. ¹H NMR spectroscopy makes feasible the study of the average block lengths of polymers once synthesized and after degradation in different media. Calorimetric data are reported, including those referred to the study of isothermal and nonisothermal crystallizations. Degradability of samples was evaluated by different methods including NMR and thermal analysis, evaluation of molecular weight by gel permeation chromatography or from intrinsic viscosity measures, scanning electron micrographs, and changes in mechanical properties. Distilled water at 70 °C acidic conditions provided by a pH 2.3 aqueous medium and enzymatic media containing lipases from Pseudomonas cepacia or Candida cylindracea were considered in this study. The degradability of the studied copolyesters strongly depends on the terephthalate content and the degradation media. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4141–4157, 2002     

Synthesis of triblock copolymers from glycolysed poly(ethylene terephthalate) by living radical polymerization

Valorization of poly(ethylene terephthalate) (PET) waste has been achieved using glycolysis. The resulting diols were employed for the synthesis of triblock copolymers by atom transfer radical polymerization using copper (I) bromide and (1,1,4,7,10,10)‐hexamethyltriethylenetetramine as catalyst system. Macroinitiator was obtained after depolymerization of PET waste followed by functionalization of the obtained glycolysate with 2‐bromoisobutyrate bromide. Polymerization of styrene (S) and glycidyl methacrylate (GMA) has been achieved leading to PS‐b‐PETG‐b‐PS and (PS‐stat‐PGMA)‐b‐PETG‐b‐(PS‐stat‐PGMA) triblock copolymers. Best results were obtained at 100 °C. At this temperature, termination reaction were negligible and the measured number‐average molar mass of the product increased linearly with monomer conversion in agreement with the theoretical M_n with low polydispersity products achieved. Polymers were also characterized by ¹H NMR. This work presents a original valorization of PET waste as (PS‐stat‐PGMA)‐b‐PETG‐b‐(PS‐stat‐PGMA) copolymer could be used as heat curable coatings. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 433–443, 2008     

Antibacterial poly(ethylene terephthalate) surfaces obtained from thymyl methacrylate polymerization

Thymol, an antibacterial agent was used for the preparation of a methacrylic monomer. The conventional and atom transfer radical (ATRP) polymerizations of this monomer were studied using different conditions. Then, the functionalization of poly(ethylene terephthalate) (PET) films by “grafting from” ATRP using this monomer was investigated. In this aim, a three steps procedure was developed. The surfaces were first treated by NH₃ plasma treatment to incorporate primary amino functions. Then, in a second step, ATRP initiator was grafted by reaction with bromoisobutyryl bromide. Surface initiated ATRP of thymyl methacrylate was performed in solution in the presence of a sacrificial initiator. The efficiency of these reactions was confirmed by X‐ray photoelectron spectroscopy. Wetting properties and surface energy were found to vary systematically depending to the type of functionalization and grafting. The poly(thymyl methacrylate)‐grafted PET surfaces exhibit resistance to bacterial adhesion toward Pseudomonas aeruginosa, Listeria monocytogenes, and Staphylococcus aureus strains. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1975–1985     

Effect of catalysts on thermally stimulated current in poly(ethylene terephthalate)

The effect of catalysts on relaxation phenomena in poly(ethylene terephthalate) (PET) was studied by thermally stimulated current (TSC). Resins Sb-PET and Ge-PET were produced by the antimony and germanium main catalyst systems, respectively. Spontaneous, global and thermal sampling of TSC were compared in both PETs. The lower TSC peaks are observed in Ge-PET than those in Sb-PET for equivalent treatment. The compensation parameters were determined from the variation polarization temperatures (Tp) data. These parameters were used to calculate degree of disorder (DOD). The DOD of Sb-PET and Ge-PET were 36.14 and 66.23, respectively. The relaxation time at the maximum current and the dipolar relaxation strength in the Sb-PET has the higher values and wider distribution than that in Ge-PET. Furthermore, Sb-PET exhibited electrically softer. These results are attributed to the stiffening amorphous parts by the entanglement network in Ge-PET. This revised version was published online in July 2006 with corrections to the Cover Date.